Approach to excellent superhydrophobicity and corrosion resistance of carbon-based films by graphene and cobalt synergism

A new series of carbon-based films doped with graphene oxide and cobalt (G-Co/a-C:H films) were successfully prepared on Si substrate via one-step electrochemical deposition of methanol as the carbon source and graphene oxide/cobalt as the dopant. G-Co/a-C:H films were fabricated at various graphene oxide concentration for comparative experiments. It can be found that the graphene oxide and cobalt were well embedded in amorphous carbon matrix to form superhydrophobic G-Co/a-C:H film at the doping GO concentration of 0.007 mg/mL, which was confirmed by transmission electron microscopy (TEM). It was noted that the superhydrophobicity of the resulting surface derives from its rough surface with hierarchical micro-nanostructures and the presence of the low-surface-energy GO components on it. The hierarchical micro-nanostructures are attributed to the corporate joint of GO and cobalt to form the multilevel nanoscale composite interface. Specially, the as-fabricated superhydrophobic G-Co/a-C:H film could exhibit excellent self-cleaning ability and corrosion resistance, revealed by the self-cleaning and corrosion tests.     

Effect of atomic oxygen irradiation on the structural and tribological characteristics of polytetrafluoroethylene and its composites

Based on the ground‐based simulation facility, the effects of atomic oxygen (AO) irradiation on the structural and tribological properties of pure polytetrafluoroethylene (PTFE) and carbon fiber and MoS₂‐filled PTFE composites were studied by scanning electron microscopy, X‐ray photoelectron spectroscopy, and a ball‐on‐disc tribometer. The results shown that AO irradiation had significant effects on the structural and tribological properties of pure PTFE, in which the surface morphologies, mass loss, friction coefficient, and wear rate had been changed greatly after AO irradiation. However, it was noticeable that the addition of carbon fiber and MoS₂ filler to PTFE could improve the AO resist capacity and tribological properties of PTFE composites significantly. Copyright © 2016 John Wiley & Sons, Ltd.     

Achieving ultra-low friction of a-C:H film grown on 9Cr18Mo steel for industrial application via programmable high power pulse magnetron sputtering

Owing to the high hardness and hydrogen passivation of carbon bonds, hydrogenated diamond-like carbon (a-C:H) film has shown promising potential to achieve ultra-low friction and wear on steel surfaces. Here, a-C:H film was successfully deposited on 9Cr18Mo steel via programmable high power pulse magnetron sputtering and potential application for industrial was evaluated. The a-C:H films against different mating materials of GCr15 steel balls, Al₂O₃, Si₃N₄, ZrO₂, and a-C:H-coated GCr15 balls all showed ultra-low friction under a normal load of 5 N in a dry ambient air environment. Among them, self-mating tribo-system a-C:H films on steel surfaces and a-C:H-coated steel balls achieve best friction performance; the principal reason is that both contacting surfaces coated with a-C:H film have the lower electron affinities compared with other tribo-systems. However, the differences of coefficient of friction (COF) for uncoated-GCr15, Al₂O₃, ZrO₂, Si₃N₄, and a-C:H(GCr15) balls can be attributed to different sizes of clustering in wear debris. This work provides new insights on synthesis and industry application of the a-C:H films with ultra-low friction properties.     

Effect of methane on magnetron sputtering graphite target deposited films and tribological properties of a-C:H:Ti/a-C:H friction pairs

In this study, we prepared a-C:H films with different nanostructures at different methane flow rates. The effect of the methane flow rate on the tribological properties of 440 steel/a-C:H friction pairs and a-C:H:Ti/a-C:H friction pairs in an atmospheric environment was studied by a reciprocating friction machine. The results show that there is no relationship between the tribological properties of 440 steel/a-C:H friction pair and methane flow rate. The tribological performance of the a-C:H:Ti/a-C:H friction pair was greatly improved. In particular, in the friction pair of a-C:H:Ti/a-C:H with a methane flow rate of 20 sccm, superlubricity is shown, and the wear rate is only 4.04 × 10⁻⁹ mm³/Nm. After tribological experiments, Raman spectroscopy, XPS, and other characterization methods were used to study the relationship between the nanostructure and tribological properties of a-C:H:Ti films and a-C:H prepared with different methane flow rates. This study is great significance to the application of a-C:H:Ti/a-C:H friction pair in mechanical parts under atmospheric environment.     

Effect of solid lubricant particles on the tribological properties of PTFE composites lubricated with natural seawater

An orthogonal test was used to design different mixture ratios of molybdenum disulfide(MoS₂), graphite, and SiO₂ particles, which were filled with polytetrafluoroethylene (PTFE) composite. MoS₂-, graphite-, and SiO₂-modified PTFE was obtained by pressing and sintering, and the processing parameters were determined using progressive studies and experiments. The friction and wear properties of different PTFE composites lubricated with natural seawater were analyzed using an MMU-5G wear tester. A laser scanning confocal microscope was employed to examine the morphological characteristics of the worn surface. Moreover, the influence of particle proportions on the tribological property of composites was analyzed. Results show that the addition of SiO₂, MoS₂, and graphite can increase the bearing capacity, improve the wear resistance, reduce the friction coefficient, and increase the self-lubricating ability of the PTFE matrix.     

Electrodeposition and characterization of Pd nanoparticles doped amorphous hydrogenated carbon films

Palladium (0) nanoparticles incorporated hydrogenated amorphous carbon (Pd/a-C:H) films were synthesized on single crystal silicon (100) substrates by electrochemical deposition route using methanol and camphor as carbon source, and Pd nanoparticles as dopant. The characterization results indicate that Pd nanocrystalline particles with diameter in the range of 1–5 nm dispersed in the amorphous carbon matrix. Compared with pure a-C:H films, the introduction of Pd nanoparticles didn't change the structure of carbon films. At the end, the growth mechanism of the Pd/a-C:H composite films was discussed.     

Structural and tribological properties of polytetrafluoroethylene composites in atomic oxygen environment

Effects of atomic oxygen (AO) irradiation on the structural and tribological behaviors of glass fiber (GF) and MoS₂ filled polytetrafluoroethylene (PTFE) composites were investigated in a ground‐based simulation facility, in which the average energy of AO was about 5 eV and the flux was 5.0 × 10¹⁵ cm^–2 s^–1. The structural changes were characterized by XPS and attenuated total‐reflection Fourier transform infrared spectroscopy, and the tribological changes were evaluated by friction and wear tests and SEM analysis of the worn surfaces. It was found that AO irradiation induced the degradation of PTFE molecular chains, and the primary erosion mechanism is collisionally induced rather than chemically induced. The addition of MoS₂ filler significantly increased the AO resistance of PTFE composites. Friction and wear tests indicated that GF and MoS₂ improved the tribological properties of materials before and after AO irradiation. Short GF and MoS₂ exhibited a good synergistic effect for improving the AO resistant and tribological properties of PTFE material. Copyright © 2012 John Wiley & Sons, Ltd.     

Tribological behaviors of DLC films in sulfuric acid and sodium hydroxide solutions

Tribological behaviors of three typical kinds of diamond-like carbon (DLC) films (a-C, a-C:Cr, and a-C:H) in sulfuric acid and sodium hydroxide solutions were investigated. The a-C film showed the lowest stable coefficients of friction (COF) in both sulfuric acid and sodium hydroxide solutions but the worst wear resistance in sulfuric acid solution. The a-C:H film showed the highest COF in sulfuric acid solution and the best wear resistance in both sulfuric acid and sodium hydroxide solutions. The a-C:Cr film exhibited superior comprehensive tribological performance in sulfuric acid solution, while in sodium hydroxide solution, high COF and very poor wear resistance was observed. What is more, friction and wear mechanism was revealed by investigating the friction-induced material evolutions on the sliding surface.     

Friction and wear behavior of PI and PTFE composites for ultrasonic motors

High‐performance polymer‐based frictional materials have become increasingly important to improve the mechanical output properties of ultrasonic motors. This study discussed the friction and wear behavior of 2 dominating frictional materials of polymer composites for ultrasonic motors, polyimide (PI), and polytetrafluoroethylene (PTFE) filled by aramid fibers (AF) and molybdenum disulfide (MoS₂). To explore the wear mechanisms, the tribo‐pair contact stress was theoretically characterized, and the interface temperature rise was numerically predicted. The predictions showed that the flash temperature on asperity tips could reach the glass transition temperature of the polymer materials. The experimental results indicated that the contact stress and sliding speed have a small effect on the friction of the PI composite but influence considerably the friction of the PTFE composite. A higher contact stress brings about a higher specific wear rate, but a higher sliding speed reduces the wear rate. Compared with AF/MoS₂/PTFE, the AF/MoS₂/PI has much better tribological performance under high loads and speeds.     

大功率激光制备a-C和a-C∶H类金刚石膜的光学性能研究

采用大功率高重复频率准分子激光溅射热解石墨靶制备了类金刚石碳膜, 研究了实验条件对类金刚石膜光学性能的影响, 发现氢可以提高膜中sp3键的含量和膜的光学透过率. 在实验参数范围内, 膜的光学性能随着氢压的增加而提高. 根据类金刚石膜的反应沉积机理对上述结果进行了分析、解释.     

Tribological behavior of polyurethane-based composite coating reinforced with TiO2 nanotubes

The unmodified and hexamethylene diisocyanate (HDI) modified TiO₂ nanotubes, were used for fabricating TiO₂ nanotubes (TiNTs)/polyurethane (PU) composite coating. The effects of applied load and sliding speed on the tribological behavior of the composite coating were investigated using a block-on-ring wear tester. Compared to the TiO₂ nanotubes filled PU composite coating, the HDI modified TiO₂ nanotubes (TiNTs-HDI) filled one had the lower friction coefficient and higher wear life under various applied loads and sliding speed. Scanning electron microscope (SEM) investigation showed that the TiNTs-HDI filled PU coating had smooth worn surface under given applied load and sliding speed, and a continuous and uniform transfer film formed on the surface of the counterpart ring, which helped to reduce the wear of the coating. The improvement in the tribological properties of TiNTs-HDI/PU composite coating might due to an improvement in interfacial adhesion between TiNTs and PU after HDI treatment. The strong interfacial coupling of the composite coating made TiNTs-HDI not easy to detach from the PU matrix, and prevented the rubbing-off of PU composite coating, accordingly improved the friction and wear properties of the composite coating.     

The structure and tribological properties of aluminum/carbon nanocomposite thin films synthesized by reactive magnetron sputtering

Hydrogenated nanocomposite aluminum/carbon thin films (Al/a‐C:H) were fabricated on stainless steel and silicon wafer substrates via unbalanced reactive magnetron sputtering from an Al target in CH₄/Ar plasma. The composition and structure of Al/a‐C:H films were investigated by high‐resolution transmission electron microscope (HRTEM), XPS and micro‐Raman spectroscopy. Nanoindenter, interferometer and ball‐on‐disc tribometer were carried out to evaluate the hardness, internal stress and tribological properties of Al/a‐C:H films. HRTEM observations confirmed that the metallic Al nanocrystallites were uniformly dispersed in the amorphous carbon matrix. XPS and Raman analyses indicated that the sp² content increased with the increase of Al content in the films. Nanoindenter and interferometer tests exhibited that the uniform incorporation of Al nanocrystallites can diminish drastically the magnitude of internal stress with maintaining the higher hardness of as‐deposited films. Especially, the ball‐on‐disc tribometer measurements revealed that the nanocomposite film with 2.3 at.% Al content exhibited relatively better wear resistance and self‐lubrication performance with a friction coefficient of 0.06 and wear rate of 3.1 × 10^?16 m³/ N·m under ambient air, which can be attributed to the relatively higher hardness, the formation of continuous graphitized transfer film on counterface and the reduced reaction of oxygen with carbon. Copyright © 2010 John Wiley & Sons, Ltd.     

片状MoS2/MoS1.5Se0.5纳米复合材料的制备及其摩擦学性能研究

将钼粉与升华硫和硒粉的混合粉末按一定化学计量比混合,通过固相反应法成功制备出了均匀的片状纳米颗粒。分别使用X射线粉末衍射仪(XRD)、扫描电子显微镜(SEM)以及透射电子显微镜(TEM)对该纳米粉体进行结构表征和分析,发现该粉体为MoS2/MoS1.5Se0.5混合晶相,晶粒尺寸在300~600 nm,厚度约为5 nm的片状结构。将该MoS2/MoS1.5Se0.5纳米片作为润滑油添加剂添加到基础油中,使用UMT-2型摩擦磨损试验机对其摩擦学性能进行测试,并对摩擦机理进行了解释,结果表明MoS2/MoS1.5Se0.5纳米片作为润滑油添加剂具有良好的减摩抗磨性能。     

Cu掺杂TiO_2薄膜的摩擦学性能

采用溶胶-凝胶法在普通玻璃基底上制备了纯TiO2和Cu掺杂的TiO2(Cu-TiO2)纳米结构薄膜,利用X射线光电子能谱(XPS)、原子力显微镜(AFM)、粉末X射线衍射(XRD)及UMT-3摩擦磨损试验机考察了Cu掺杂量对薄膜组成、结构、表面形貌及摩擦学性能的影响.结果表明,相比于纯TiO2薄膜,Cu掺杂TiO2纳米薄膜平整、均匀,具有较好的耐磨减摩性能.Cu掺杂量的多少直接影响Cu-TiO2薄膜的减摩抗磨性能,当Cu掺杂量为5%(摩尔分数)时,Cu-TiO2膜具有最佳的耐磨寿命和最低的摩擦系数.     

Importance of the catalytic effect of the substrate in the functionality of lubricant additives: the case of molybdenum dithiocarbamates

Molybdenum dithiocarbamates (MoDTCs) are lubricant additives very efficient in reducing the friction of steel, and they are used in a number of industrial applications. The functionality of these additives is ruled by the chemical interactions occurring at the buried sliding interface, which are of key importance for the improvement of the lubrication performance. Yet, these tribochemical processes are very difficult to monitor in real time. Ab initio molecular dynamics simulations are the ideal tool to shed light on such a complicated reactivity. In this work, we perform ab initio simulations, both in static and tribological conditions, to understand the effect of surface oxidation on the tribochemical reactivity of MoDTC, and we find that when the surfaces are covered by oxygen, the first dissociative steps of the additives are significantly hindered. Our preliminary tribological tests on oxidized steel discs support these results. Bare metallic surfaces are necessary for a stable adsorption of the additives, their quick decomposition, and the formation of a durable MoS₂ tribolayer. This work demonstrates the importance of the catalytic role of the substrate and confirms the full capability of the computational protocol in the pursuit of materials and compounds more efficient in reducing friction.     

Effects of atomic oxygen irradiation on structural and tribological properties of polyimide/Al2O3 composites

To understand the effects of atomic oxygen (AO) irradiation on the structural and tribological behaviors of polymer composites, polyimide/Al₂O₃ composites were irradiated with AO in a ground‐based simulation facility. The structural changes were characterized by X‐ray photoelectron spectroscopy and attenuated total‐reflection FTIR, whereas the tribological changes were evaluated by friction and wear tests as well as scanning electron microscopy analysis of the worn surfaces. It was found that AO irradiation induced the oxidation and degradation of polyimide molecular chains, which increased the O concentration and decreased the C concentration in the composite surfaces. The destruction action of AO changed the surface chemical structure and morphology of the samples. Friction and wear tests indicated that AO irradiation decreased the friction coefficient but increased the wear rate of both pure and Al₂O₃ filled polyimides. In terms of the tribological properties, appropriate content of Al₂O₃ might be favorable for the improvement of tribological properties in AO environment. Copyright © 2011 John Wiley & Sons, Ltd.     

Superlubricity behaviors of Si3N4/DLC Films under PAO oil with nano boron nitride additive lubrication

The tribological properties of Si₃N₄ ball sliding against diamond‐like carbon (DLC) films were investigated using a ball‐on‐disc tribometer under dry friction and oil lubrications, respectively. The influence of nano boron nitride particle as lubricant additive in poly‐α‐olefin (PAO) oil on the tribological properties of Si₃N₄/DLC films was evaluated. The microstructure of DLC films was measured by Raman spectroscopy and X‐ray photoelectron spectroscopy. The experimental results show coefficient of friction (COF) of Si₃N₄/DLC films was as low as 0.035 due to the formation of graphite‐like transfer films under dry friction condition. It also indicates that the tribological properties of Si₃N₄/DLC films were influenced significantly by the viscosity of oil and the content of nano boron nitride particle in PAO oil. COF increases with the viscosity of PAO oil increasing. Si₃N₄/DLC films exhibit the superlubricity behaviors (μ=0.001 and nonmeasurable wear) under PAO 6 oil with 1.0 wt% nano boron nitride particle lubrication, indicating that the improved boundary lubrication behaviors have indeed been responsible for the significantly reduced friction. Nano boron nitride additive is used as solid lubricant‐like nano scale ball bearing to the pointlike contact and a soft phase bond with the weak van der Waals interaction force on the contact surface to improve the lubrication behaviors of Si₃N₄/DLC films. The potential usefulness of nano boron nitride as lubricant additive in PAO oil for Si₃N₄/DLC films has been demonstrated under oil lubrication conditions. The present work will extend the wide application of nano particle additive and introduce a new approach to superlubricity under boundary lubrication in future technological areas. Copyright © 2013 John Wiley & Sons, Ltd.     

Tribological behaviour of nanostructured Ti-C:H coatings for biomedical applications

The development of a mechanically stable, functionally graded Ti-doped a-C:H interface layer in combination with a functional a-C:H coating requires a reduction of the brittle phases which induce generally problems in the transitions from Ti to TiC/a-C:H. The core objective of this study was to develop an optimum interlayer between the substrate and the functional top layer for biomedical applications, namely for tooth implants. Since the interlayer may be exposed to the sliding process, in the case of local failure of the top layer it has to fulfil the same criteria: biocompatibility, high wear resistance and low friction.The functional Ti-C:H layers with thickness in the range 2.5–3.5 μm were deposited by a magnetron sputtering/PECVD hybrid process by sputtering a Ti-target in a C₂H₂ + Ar atmosphere in dc discharge regime. The sets of coating samples were prepared by varying the C and H concentrations controlled by the C₂H₂ flow during the deposition process. The tribological properties were evaluated on a pin-on-disc tribometer at room temperature (RT) and at 100 °C using 440C balls with a diameter of 6 mm. The tests at 100 °C were performed to investigate the effect of the sterilization temperature on the tribological properties and the coating lifetime as well. The tribological performance was examined with respect to the friction coefficient, the wear rates of the coating and the counter-parts and the analysis of the wear debris. The Ti/C ratio decreased almost linearly from 4.5 to 0.1 with increasing C₂H₂ flow; the hydrogen content showed a minimum of 5 at.% at C₂H₂ flow of 30 sccm, while for lower flows it was about 10 at.%. The coatings could be divided into three groups based on the C₂H₂ flow: (i) 10–15 sccm, exhibiting severe abrasive damage during the sliding tests, (ii) 20–45 sccm, showing the highest hardness and friction values, and (iii) 52–60 sccm, with moderate hardness and minimal values of the friction coefficient and the wear rate.     

Free‐standing and Flexible MoS2/rGO Paper Electrode for Amperometric Detection of Folic Acid

The development of flexible electrodes is of considerable current interest because of the increasing demand for modern electronics, portable medical products, and compact devices. We report a new type of flexible electrochemical sensor fabricated by integrating graphene and MoS₂ nanosheets. A highly flexible and free‐standing conductive MoS₂ nanosheets/reduced graphene oxide (MoS₂/rGO) paper was prepared by a two‐step process: vacuum filtration and chemical reduction treatment. The MoS₂/graphene oxide (MoS₂/GO) paper obtained by a simple filtration method was transformed into MoS₂/rGO paper after a chemical reduction process. The obtained MoS₂/rGO paper was characterized by scanning electron microscopy, X‐ray diffraction spectroscopy, X‐ray photoelectron spectroscopy, Raman spectroscopy, electrochemical impedance spectroscopy. The electrochemical behavior of folic acid (FA) on MoS₂/rGO paper electrode was investigated by cyclic voltammetry and amperometry. Electrochemical experiments indicated that flexible MoS₂/rGO composite paper electrode exhibited excellent electrocatalytic activity toward the FA, which can be attributed to excellent electrical conductivity and high specific surface area of the MoS₂/rGO paper. The resulting biosensor showed highly sensitive amperometric response to FA with a wide linear range.     

Effects of bias voltage on structure and properties of TiAl‐doped a‐C:H films prepared by magnetron sputtering

Hydrogenated TiAl‐doped a‐C:H films were deposited on Si substrates by middle frequency magnetron sputtering TiAl target in argon and methane gas mixture atmosphere. Effects of substrate bias voltage on structure and properties of the films, such as the surface morphology, hardness, chemical nature and bond types, were investigated by means of atomic force microscopy (AFM), XPS, Raman spectroscopy and nanoindentation. The friction and wear behaviors of the deposited films were characterized on an UMT‐2MT tribometer. SEM was utilized to analyze the wear scar on steel balls and debris after sliding on the deposited films under dry friction conditions. The results demonstrated that the film deposited at ? 100 V exhibited low friction coefficient which is attributed to the easier formation of graphitized transfer layer. Copyright © 2010 John Wiley & Sons, Ltd.