Fabrication of macroporous foam and microspheres of polystyrene by Pickering emulsion polymerization

Poly(styrene-co-methacrylic acid) (PS-co-MAA) particles were synthesized via surfactant-free emulsion polymerization and then used as particulate emulsifiers for preparation of Pickering emulsions. Our results showed that adjusting the solution pH can tune the wettability of PS-co-MAA particles to stabilize either water-in-oil (W/O) or oil-in-water (O/W) Pickering emulsions. Stable W/O emulsions were obtained with PS-co-MAA particles at low pH values due to their better affinity to the dispersed oil phase. In contrast, increasing the pH value significantly changed the stabilizing behavior of the PS-co-MAA particles, leading to the phase inversion and formation of stable O/W emulsions. We found that the oil/water ratio had a significant influence on pH value of the phase inversion. It decreased with decreasing the oil/water ratio, and no phase inversion occurred when the styrene volume fraction reduced to 10 %. Additionally, macroporous polystyrene (PS) foam and PS microspheres were obtained via polymerization of Pickering high internal phase emulsion (Pickering HIPE) and O/W Pickering emulsion, respectively.     

Long-term prediction of compressive creep development in expanded polystyrene

The results obtained in investigating the creep of expanded polystyrene (EPS) boards under compressive stress are presented. Power and exponential equations were used for describing creep compliance. It was found that the curves of creep compliance approximated by both equations adequately represent the research results, taking into account the scatter of the experimental data. Based on the calculation and empirical estimate of long-term creep of EPS under compressive stress σ_c=(0.25–0.45)σ_10%, its creep compliance was determined for a period of 10 years in the future. The dependence of on the density of polystyrene boards and the value of long-term compressive stress σ_c was established. The expected values of creep strain development in expanded polystyrene boards EPS 80–EPS 250 under constant compressive stress σ_c=(0.25–0.45)σ_10% are presented for the prediction period of 10 years. To obtain the expected creep values for any other period of time in the interval of 5T50 years, the values of should be multiplied by the empirical coefficient .     

Thermal decomposition of polystyrene foam under controlled atmosphere and temperature conditions

The thermal decomposition of polystyrene foam with and without tetrabromovinylcyclohexene, at sample sizes permitting secondary reactions, was studied. The decomposition was carried out in a carefully controlled device providing high reproducibility at 823, 1023 and 1223 K, in air, in a mixture of air and nitrogen and in nitrogen. No flame source was included. The volatile products (boiling range roughly 350–750 K) were studied by gas chromatography—mass spectrometry.The study showed that the amounts of the products were dependent on the decomposition temperature and on the kind of sample. The products were very complex mixtures, containing, amongst others, monomer, oligomers, fused aromatic ring compounds, oxidized hydrocarbons and bromine-containing products. The types and amounts of the products were influenced by the atmosphere, the decomposition temperature and the type of sample.     

Application of modified wastes from phenol-formaldehyde resin and expanded polystyrene in sewage treatment processes

A solution to environmental pollution by polymer plastic wastes can be their chemical modification in to useful products. Such a new solution is the obtaining of effective flocculants for sewage treatment from chemically modified phenol-formaldehyde resin production wastes (SE and NS novolak) and expanded polystyrene wastes. Comparative analysis of flocculation properties was performed for amino derivatives of novolak wastes, synthesized sulphonated derivatives of novolak and expanded polystyrene wastes, of standard polyacryloamide and for Praestol commercial polyelectrolyte. Amino derivatives and sulphonated derivatives of polymer plastic wastes, having properties of anionic type polyelectrolytes, exhibit good flocculation properties in purification processes of sewages with a chemical composition close to that of found in the water circulating system power plant, coal-mine, and steel plant. Application of synthesised flocculants caused a decrease of turbidity, concentration of solved impurities and improved quality parameter of purified water. It was found that synthesised polyelectrolytes could be used in industrial water treatment processes.     

Fire hazard evaluation of activated carbons

Journal of Thermal Analysis and Calorimetry - Activated carbons are widely used in the iodine adsorbers in nuclear plants, but little information about their combustibility is available for fire...     

Efficiency of Cd(II) removal from aqueous media using chemically modified polystyrene foam

The removal of Cd(II) using polystyrene foam chemically modified with 2,2′-bipyridine has been investigated. The modified polystyrene foam has been characterized by FT-IR spectroscopy, thermogravimetry, elemental analysis and scanning electron microscopy. The solid was employed as a Cd(II) adsorption from aqueous solutions at room temperature. The effects of several variables (pH, shaking speed, agitation time, metal concentration and presence of other ions in the medium) have been studied using batch technique. Flame atomic absorption spectrometry was used to determine the Cd(II) ion concentration in the filtrate after the adsorption process. Maximum sorption 90% was achieved at pH 7 after 30 min of shaking time. Sorbed metal ions have been desorbed with 5 ml of 2 M HNO₃ with the detection limit of 16.7 ng ml⁻¹. The Langmuir, Freundlich and D–R isotherm equation were used to describe partitioning behavior of the system at room temperature. Kinetic and thermodynamic behavior of modified polystyrene foam for Cd(II) ion removal was also studied. Br⁻, PO₄³⁻, Pb²⁺, Ni²⁺ and Cr(VI) suppress the sorption to some extent. The possible sorption mechanism of Cd(II) ions onto modified sorbent is also discussed. Method was utilized to remove Cd(II) ions from aqueous media.     

Thermoplastic elastomers based on waste rubber and expanded polystyrene: Role of devulcanization and ionizing radiation

Waste rubber (WR) powder as a vulcanized one was introduced into a two-roll mill in the presence of various ratios of curatives to develop sheets of devulcanized waste rubber (DWR). Thermoplastic elastomers (TPE) were prepared by blending either WR or the obtained DWR with the waste of expanded polystyrene (EPS) at a fixed ratio of 70 rubber/30 EPS in the absence or presence of gamma irradiation at 100?kGy. Maleic anhydride (MA) 1?wt% with respect to rubber was used as coupling agent. The mechanical parameters of the blends: tensile properties, rheology, hardness (Shore D), and abrasion resistance were studied.     

Analysis of volatiles associated with industrial scale processing of expanded polystyrene. Part I: Methods development

This paper reports on the methodology to collect volatiles from the hot-wire cutting of expanded polystyrene. Analytical scale pyrolysis was used to model the conditions in the field. It appears that gas chromatographic profiles are little affected by the presence or absence of flame retardants. Pyrolysis in air or in an inert gas generates very similar pyrograms but the temperature at which pyrolysis takes place is the major factor affecting amount and distribution of volatiles. An experimental design is discussed that permits to model in the laboratory the production of volatiles generated in the field.     

Drainage of aqueous film-forming foam stabilized by different foam stabilizers

The present study focuses on the drainage property of aqueous film-forming foam stabilized by different types and concentrations of foam stabilizers. Aqueous film-forming foam (AFFF) formulation concentrates are prepared based on the main components of fluorocarbon surfactant, hydrocarbon surfactant, and organic solvents. Carboxymethylcellulose sodium (CS), xanthan gum (XG), and lauryl alcohol (LA) are selected as foam stabilizers of the AFFF. Surface tension, viscosity, and foamability tests of the AFFF solutions are conducted to evaluate the effect of foam stabilizers on the properties of AFFF solutions. Particularly, an apparatus is established based on the law of connected vessel in order to obtain the instantaneous mass of liquids drained from foams. The drainage features of the AFFFs containing different foam stabilizers are analyzed and compared with each other. The results indicate that AFFF drainage is significantly affected by the type and the concentration of foam stabilizers. The addition of CS and XG to AFFF results in a deceleration of foam drainage, while foam drainage is accelerated by the addition of LA. The variations of surface tension, viscosity, and liquid fraction of foams are the main reasons for the varying foam drainage rate. This study provides a direct connection between chemical components and fundamental properties of AFFF.     

Analysis of volatiles associated with industrial scale processing of expanded polystyrene Part II: Identification and quantitation

Expanded polystyrene was pyrolyzed on a laboratory scale hot wire cutter. The resulting volatiles were characterized using GC/MS as the primary analytical tool. Use was also made of retention data from a complex petrochemical standard. In situ bromination of the pyrolysate further helped in structure elucidation. Air samples were collected in the field and compared to the model experiments from a laboratory scale hot wire cutter. The results indicate that alkylbenzene type compounds were the primary compounds in this environment. A few oxygenated substances were also formed. Traces of brominated compounds were detected in the model experiments but not in the samples collected in the field, with one exception. Quantitative data are presented from a typical industrial operation.     

Fluorescence quenching of polystyrene by oxygen

The fluorescence quenching of polystyrene by oxygen at room temperature was investigated. The diffusion coefficient of oxygen in polystyrene films was taken as 3.1 × 10^?7 cm²/sec; the energy migration coefficient of polystyrene in the excited singlet state was estimated as 6 × 10^?6 cm²/sec.     

Sorption of organic vapors by polystyrene

Activity coefficients of benzene, toluene, cyclohexane, carbon tetrachloride, chloroform, and dichloromethane in binary solutions with polystyrene at 23.5°C have been determined using a piezo-electric sorption apparatus. The investigated solvent concentration ranges were 15 to 39 wt % for benzene, 14 to 29 wt % for toluene, 15 to 28 wt % for cyclohexane, 26 to 38 wt % for carbon tetrachloride, 24 to 46 wt % for chloroform, and 21 to 41 wt % for dichloromethane. The polystyrene (weight-averaged) molecular weights were 1.1 × 10⁵ and 6.0 × 10⁵ g/gmole. The weight-fraction activity coefficients (Ω₁ = a₁/w₁) of cyclohexane, toluene, and carbon tetrachloride in polystyrene solutions determined in this work agree within experimental error with previously published values determined by measurement of vapor pressure lowering and vapor absorption by thin films. We find disagreement, at low solvent concentrations, between our results for benzene and chloroform and previously published results. We have analyzed our results using Flory's version of corresponding-states polymer solution theory. The theory can account, qualitatively, for the cyclohexane and carbon tetrachloride results. It cannot account for the toluene, benzene, dichloromethane, or chloroform results.     

Positron annihilation lifetime evaluation of thermal cycling effects in atactic polystyrene

Positron annihilation lifetime spectroscopy (PALS) was used to investigate the thermal cycling characteristics of two different molecular weight atactic polystyrene resins. Annealed compression molded samples were thermally cycled over the temperature range 253 K to 393 K with PAL spectra taken in 10 K increments upon both cooling and heating. The longest lived component lifetime and intensity, indicative of orthopositronium pick-off, exhibit thermal dependencies that can be interpreted in a manner consistent with anticipated free volume changes associated with structural transitions.     

单分散交联聚苯乙烯色谱填料的制备与评价

与生命科学相关的分离技术促进了高效液相色谱中聚合物填料的发展.因为硅胶基质填料在某些色谱模式及生物分子所要求的分离条件下不稳定.1979年,Ugelstand等[1]提出了活化多步溶胀法使单分散小粒径聚合物颗粒的制备成为可能.其理论基础是[2]:使用一种能使种子颗粒的单体溶胀能力大幅度提高的水不溶性低分子量溶剂(溶胀活化剂),通过溶胀活化作用使大小均匀的聚合物种子颗粒溶胀活化.     

Effect of blowing agent content on the structure and flame-retardant properties of rigid polyurethane foam/expanded graphite composites

Driven by global environmental issues, the development of green building materials has become an immediate focus. In this work, n-pentane was used as an environmentally friendly blowing agent to prepare flame-retardant rigid polyurethane foam (RPUF) with the addition of expandable graphite (EG) successfully, and the effect of n-pentane content on flame retardancy and compressive properties of RPUF/EG composites was investigated through limit oxygen index (LOI), vertical burning test (UL-94), scanning electron microscope (SEM), thermogravimetric analysis (TGA), and compressive properties test. SEM results show that the content of EG and n-pentane causes a change in the cell structure of RPUF. The change of the n-pentane content has also an obvious effect on the thermal stability, flame retardancy, and specific compressive strength of RPUF/EG composites. In addition, the cell structure of RPUF matrix has an obvious influence on the distribution of EG in the composites, which indirectly affects the flame-retardant efficiency of EG. This research explores the conditions for the application of environmentally friendly RPUF and expands its application prospects.     

High-throughput evaluation of lipophilicity and acidity by new gradient HPLC methods

There is a need for fast testing of drug candidates for properties of pharmacokinetics and pharmacodynamics importance, in particular lipophilicity and acidity. These two parameters can conveniently be estimated by gradient reversed-phase HPLC. Appropriate conventional organic solvent gradient and the new pH gradient HPLC procedures are presented. The chromatographic parameter of lipophilicity, log kw, can be determined from two organic solvent gradient runs instead of 6-8 runs necessary in the standard isocratic (polycratic) approach. The newly introduced pH gradient reversed-phase HPLC consists in a programmed increase during the chromatographic run of the eluting power of the mobile phase with regards to ionizable analytes. The eluting strength of the mobile phase increases due to its increasing (in case of acidic analytes) or decreasing (basic analytes) pH, whereas the content of organic modifier remains constant. It has been theoretically and experimentally demonstrated that the pKa and log kw values can be evaluated based on retention data from a pH gradient run, combined with appropriate data from two organic solvent gradient runs. The gradient HPLC-derived log kw parameters correlate well with analogous parameters determined isocratically as well as with reference lipophilicity parameter log P (logarithm of n-octanol/water partition coefficient). Also, the HPLC-derived pKa parameters correlate to the literature pKa values (w(w)pKa), conventionally determined by titrations in water. The approach described allows rapid and high-throughput assessment of log kw and pKa for large series of drugs candidates, also when the analytes are available in a form of mixture, e.g. produced by combinatorial synthesis.     

A computer program for a general case evaluation of the expanded uncertainty

The ISO Guide to the Expression of Uncertainty in Measurement provides a uniform method for the evaluation of combined standard uncertainty of a measurand whose expectation and standard deviation are stable over the measurement period. However, the method provided for the evaluation of the expanded uncertainty is not complete. Particularly, it does not include the case where the contributing components are correlated. Also, the probability distribution of the combined uncertainty must be close to a Normal distribution otherwise other methods must be used. The method presented here, which is implemented in a computer program, is based on a combination of the ISO guide method and Monte-Carlo simulation.The Monte-Carlo Simulation can obtain the data needed for the evaluation of the expanded and standard uncertainties directly from the measurement equation (that defines the measurand in terms of the contributing components) or from a spreadsheet-like format. Some sample results obtained by the computer program using both methods are compared and discussed.     

Benchtop micromolding of polystyrene by soft lithography

Polystyrene (PS), a standard material for cell culture consumable labware, was molded into microstructures with high fidelity of replication by an elastomeric polydimethylsiloxane (PDMS) mold. The process was a simple, benchtop method based on soft lithography using readily available materials. The key to successful replica molding by this simple procedure relies on the use of a solvent, for example, gamma-butyrolactone, which dissolves PS without swelling the PDMS mold. PS solution was added to the PDMS mold, and evaporation of the solvent was accomplished by baking the mold on a hotplate. Microstructures with feature sizes as small as 3 μm and aspect ratios as large as 7 were readily molded. Prototypes of microfluidic chips made from PS were prepared by thermal bonding of a microchannel molded in PS with a flat PS substrate. The PS microfluidic chip displayed much lower adsorption and absorption of hydrophobic molecules (e.g. rhodamine B) compared to a comparable chip created from PDMS. The molded PS surface exhibited stable surface properties after plasma oxidation as assessed by contact angle measurement. The molded, oxidized PS surface remained an excellent surface for cell culture based on cell adhesion and proliferation. To demonstrate the application of this process for cell biology research, PS was micromolded into two different microarray formats, microwells and microposts, for segregation and tracking of non-adherent and adherent cells, respectively. The micromolded PS possessed properties that were ideal for biological and bioanalytical needs, thus making it an alternative material to PDMS and suitable for building lab-on-a-chip devices by soft lithography methods.