Microstructure and dielectric properties of Nd doped CaCu3Ti4O12 synthesized by sol–gel method

Ca_(1?3x/2)Nd _x Cu₃Ti₄O₁₂ (x = 0, 0.1, 0.2 and 0.3) powders and ceramics were prepared by sol–gel method. Effect of Nd on microstructure and dielectric properties were investigated. XRD patterns suggest that pure perovskite-like CCTO phase were obtained after calcining at 800 °C for 2 h. SEM pictures reveal that particle size monotonously decreases from 250 to 120 nm with increase of Nd concentration. The lattice parameters show an increasing trend with the enhancing amount of Nd³⁺ substitution. The average grain size of CCTO ceramics decrease from 2.0 to 0.8 μm with increase in Nd doping, which indicates that high concentration of Nd inhibits grain growth of CaCu₃Ti₄O₁₂. Both of the dielectric constant and dielectric loss decrease with increase in Nd concentrations. Ca_(1?3x/2)Nd _x Cu₃Ti₄O₁₂ ceramics with x = 0.3 shows the lowest dielectric constant of 1.12 × 10⁴ as well as the lowest dielectric loss value of 0.12 at 20 °C(10 kHz).     

Preparation and characterization of CaCu3Ti4O12 powders by non-hydrolytic sol–gel method

CaCu₃Ti₄O₁₂ (CCTO) powders were prepared via a non-hydrolytic sol–gel (NHSG) method by using acetylacetone as chelating agent and ethylene glycol as solvent. The samples were characterized by TG–DSC, Fourier transform infrared spectroscopy, X-ray diffraction and scanning electron microscope. The dielectric properties of ceramics were also measured. The pure perovskite-like CCTO powders were obtained by heat treatment at 800 °C for 2 h. The average particle sizes of CCTO powders calcined at 800 °C were approximately 350–450 nm. The samples sintered at 1,000 °C showed the mean grain size of 2.5–4 μm. Specially, the ceramics exhibited high dielectric constant (1.19 × 10⁵–1.40 × 10⁵) and low dielectric loss (0.051–0.1) in the temperature range of 30–110 °C. Moreover, with the NHSG method the period of synthesis process was greatly shortened.     

From Synthesis to Applications: Copper Calcium Titanate (CCTO) and its Magnetic and Photocatalytic Properties

Investigations focusing on electrical energy storage capacitors especially the dielectric ceramic capacitors for high energy storage density are attracting more and more attention in the recent years. Ceramic capacitors possess a faster charge-discharge rate and improved mechanical and thermal properties compared with other energy storage devices such as batteries. The challenge is to obtain ceramic capacitors with outstanding mechanical, thermal and storage properties over large temperature and frequencies ranges. ABO₃ as a type of perovskites showed a strong piezoelectric, dielectric, pyroelectric, and electro-optic properties useful as energy storage and environmental devices. CaCu₃Ti₄O₁₂ (CCTO) perovskite with cubic lattice (Im3 symmetry) was discovered to have a colossal dielectric constant (10⁴) that is stable over a wide range of frequencies (10 Hz–1 MHz) and temperature independence (100–300 K). The origin of this high dielectric constant is not fully established, specially because it is the same for single crystal and thin films. In this review, the history of CCTO will be introduced. The synthesis and the sintering approaches, the dopant elements used as well as the applications of CCTO will be reported. In addition to dielectrical properties useful to energy storage devices; CCTO could serve as photocatalytic materials with a very good performance in visible light.     

Thermal behavior of BST//PVDF ceramic–polymer composites

In this paper, we report the results of a study of microstructure and thermal behavior of ceramic–polymer composites composed of barium strontium titanate Ba_0.6Sr_0.4TiO₃ (BST60/40) and polyvinylidene fluoride (PVDF). The Ba_0.6Sr_0.4TiO₃ ceramic powder was prepared by the sol–gel method. Thermal evolution of the dried gel as well as ceramic powder was studied by simultaneous thermal analysis. The composite BST60/40//PVDF was obtained by hot pressing method for volume fraction of BST60/40 ceramic powder c _v = 50 %. The morphology of BST60/40//PVDF composite powder was observed by transmission electron microscopy and the morphology of BST60/40//PVDF composite sample was observed by scanning electron microscopy. Temperature dependence of dielectric constant and dielectric loss factor of BST60/40//PVDF composites was measured in the frequency range of f = (10 × 10³–1 × 10⁶) Hz. Dynamic mechanical properties of BST60/40//PVDF composites were measured by dynamic mechanical thermal analysis DMTA.     

Influence of magnetic and dielectric loss of polymer composites containing magnetic flake particles (Sendust,Permalloy) on noise absorption in microstrip lines

Magnetic and dielectric loss have been systematically controlled by using two kinds of high-permeability particles with different electrical conductivity (Sendust, Permalloy), and the effect of the magnetic and dielectric loss on the noise-absorbing properties has been investigated. Noise-absorbing sheets are composite materials of magnetic flake particles of high aspect ratio dispersed in a polymer matrix. The frequency dispersion of the complex permeability was almost the same for the Sendust and Permalloy composite specimens. However, the complex permittivity of the Permalloy composite (ε _r′ ≈ 250, ε _r″ ≈ 50) was much greater than that of the Sendust composite (ε _r′ ≈ 70, ε _r″ ≈ 0). Enhancement of the space-charge polarization between the highly conductive Permalloy particles results in the high values of ε _r′ and ε _r″. Due to the large dielectric loss of the Permalloy composite (in addition to its inherent magnetic loss), the bandwidth of noise absorption is increased, especially in the lower frequency region. Dielectric loss should be considered in the design of broad-bandwidth noise-absorbing composites.     

Ba0.6Sr0.4TiO3/聚偏氟乙烯-聚甲基丙烯酸甲酯复合材料的制备及其介电性能

采用流延热压工艺制备Ba_0.6Sr_0.4TiO₃(BST)/聚偏氟乙烯(PVDF)?聚甲基丙烯酸甲酯(PMMA)复合薄膜,研究了PMMA含量对复合材料微观组织结构和介电性能的影响规律。结果表明,BST相能够均匀分散在聚合物基体中,归因于PMMA与PVDF良好的相容性,2种聚合物之间的界面不分明;随着PMMA含量的增加,复合材料的介电常数先降低后升高,耐击穿强度和介电可调性先增加后减少。PMMA含量(体积分数)为15%的BST/PVDF?PMMA₁₅复合材料的综合性能最佳:介电常数为23.2,介电损耗为0.07,耐击穿强度为1412 kV·cm^-1,在550 kV·cm^-1偏压场下,介电可调性为26.2%。     

Preparation and thermal reliability of <Emphasis Type="Italic">N</Emphasis>-butyl stearate/methyl palmitate composite phase change material

In this study, a series of binary mixtures of N-butyl stearate (nBS) and methyl palmitate (MP) were used to produce a novel composite phase change material (CPCM) for potential application in the eastern China, and their thermal properties were investigated by differential scanning calorimetry (DSC). The results of DSC indicated that the mixture consisting of 10 mass% nBS and 90 mass% MP is optimum as the CPCM in terms of the phase change temperature ranges (T _f = 19.74–5.59 °C; T _m = 18.34–33.80 °C) and latent heats (ΔH _f = 176.8 J g^?1; ΔH _m = 189.3 J g^?1). On the other hand, the thermal reliability and chemical stability of the CPCM after 120, 180, 240, 300, 360 and 500 accelerated thermal cycling tests were studied by DSC and fourier transform infrared (FTIR) analysis. The results demonstrated that the CPCM had good thermal reliability and chemical stability.     

Influences of Sr2+ Doping on Microstructure,Giant Dielectric Behavior,and Non-Ohmic Properties of CaCu3Ti4O12/CaTiO3 Ceramic Composites

The microstructure, dielectric response, and nonlinear current-voltage properties of Sr²⁺-doped CaCu₃Ti₄O₁₂/CaTiO₃ (CCTO/CTO) ceramic composites, which were prepared by a solid-state reaction method using a single step from the starting nominal composition of CCTO/CTO/xSrO, were investigated. The CCTO and CTO phases were detected in the X-ray diffraction patterns. The lattice parameter increased with increasing Sr²⁺ doping concentration. The phase compositions of CCTO and CTO were confirmed by energy-dispersive X-ray spectroscopy with elemental mapping in the sintered ceramics. It can be confirmed that most of the Sr²⁺ ions substituted into the CTO phase, while some minor portion substituted into the CCTO phase. Furthermore, small segregation of Cu-rich was observed along the grain boundaries. The dielectric permittivity of the CCTO/CTO composite slightly decreased by doping with Sr²⁺, while the loss tangent was greatly reduced. Furthermore, the dielectric properties in a high-temperature range of the Sr²⁺-doped CCTO/CTO ceramic composites can be improved. Interestingly, the nonlinear electrical properties of the Sr²⁺-doped CCTO/CTO ceramic composites were significantly enhanced. The improved dielectric and nonlinear electrical properties of the Sr²⁺-doped CCTO/CTO ceramic composites were explained by the enhancement of the electrical properties of the internal interfaces.     

Thermal,structural, and impedance analysis of nanocrystalline magnesium chromite spinel synthesized via hydrothermal process

Nanocrystalline magnesium chromite spinel was synthesized through hydrothermal reaction of metal nitrate solutions in stoichiometric amount at different pH, temperature and time intervals. The synthesized products were characterized for crystallinity, phase identification, and surface morphology by X-ray diffraction (XRD) and scanning electron microscope (SEM). XRD patterns showed that as-synthesized product remained amorphous up to 250 °C. However, well-crystallized magnesium chromite spinel structure is formed after calcination at 850 °C. Rietveld refinement study confirms the formation of single-phase cubic structure MgCr₂O₄ with lattice parameter a = 8.3347 Å, and Fd3m space group. The as-processed MgCr₂O₄ products showed extensive XRD line broadening, and the mean crystallite size of such crystals was found to be mainly in size range of 85–124 nm. Surface SEM images of calcined specimens revealed that the matrix is uniform, and no separation of secondary phase was detected. Thermal stability was examined by thermogravimetry (TG), differential thermal analysis (DTA), and differential scanning calorimetry. TG/DTA reveals that MgCr₂O₄ is thermally stable above 700 °C. Fourier transform infrared (FTIR) spectra studies shows two strong bands, one around 600 cm^?1 which is attributed to the intrinsic vibrations of tetrahedral and other at 400 cm^?1 is due to octahedral one. FTIR confirms the formation of metal oxides. The bandgap energy was estimated by absorption spectroscopy in ultraviolet–visible range and was found to be 0.693 eV for MgCr₂O₄ specimen sintered at 1,000 °C. Isothermal shrinkage characteristic and coefficient of thermal expansion were determined by dilatometry. The powder specimens showed excellent densification at 1,250 °C temperature and uniformly fine grain sintered ceramics (>90 % relative density) with submicron grain size (2–5 μm) were obtained after sintering at 1,000–1,250 °C. Impedance studies were carried out at room temperature and equivalent circuit model (R ₁ Q ₁) (R ₂ Q ₂) (R ₃ Q ₃) is used to explain different relaxation processes. We report largest impedance values i.e., 6.74 × 10⁸ Ω, reduced dielectric constant (≈1.0), and low tangent loss (0.8) for MgCr₂O₄ sintered at 1,250 °C.     

The synthesis and properties of CaCu3Ti4O12 thin films

The CaCu₃Ti₄O₁₂ (CCTO) thin films were synthesized via a metal‐organic solution containing stoichiometric amounts of the metal cations at 700 °C for 1 h. The stable metal‐organic solution was prepared by dissolving calcium nitrate, copper nitrate, and tetrabuty titanate in grain alcohol. The phases, microstructures, and electric properties of CCTO thin films were characterized by X‐ray diffraction, scanning electron microscopy, atomic force microscope, and electric measurements. The results show that the CCTO thin films have homogeneous microstructure, smooth surface, low leakage current, and high values of dielectric constant. The low leakage current can be attributed to the small surface roughness. The high value of dielectric constant can be attributed to the internal barrier layer capacitor mechanism and metal‐insulator‐semiconductor junction of CCTO thin films. Copyright © 2013 John Wiley & Sons, Ltd.     

Electrochemical performance and stability of nano-particulate and bi-continuous La1−X Sr X CoO3 and Ce0.9Gd0.1O1.95 composite electrodes

A bi-continuous porous cathode consisting of nano-particles of strontium substituted lanthanum cobaltite (LSC) covering the surface of a Ce_0.9Gd_0.1O_1.95 (CGO10) backbone has been produced. The polarization resistance (R _P) of this cathode was measured to ～35 mΩ cm² at 650 °C. The area-specific resistance at 650 °C (ASR) when applied onto an anode supported cell (ASC) was found to increase from 540 to 730 mΩ cm² when subjected to a thermal cycle to 850 °C. This effect was attributed to particles coarsening but also to a reaction with the electrolyte. The results imply that a CGO10 barrier is required for this type of nano-structured cathode.     

A one-dimensional silver(I) coordination polymer with saccharin and pyrazine: synthesis,crystal structure,thermal analysis,FTIR spectra,and DFT studies

A silver(I) complex of saccharinate (sac) with pyrazine (pyz), [Ag(sac)(pyz)] _n , has been synthesized and characterized by elemental analysis, IR, thermal analysis, and single-crystal X-ray diffractometry. The complex crystallizes orthorhombic space group Pnma with unit cell parameters of a = 13.0073(9) Å, b = 6.4907(6) Å, c = 13.4007(9) Å, V = 1131.37(15) Å³, and Z = 4. [Ag(sac)(pyz)] _n is a one-dimensional coordination polymer, in which the sac ligand acts as a monodentate ligand through the N atom and the trigonal silver centers are linked by the bridging pyz ligands. The individual chains are connected into two-dimensional supramolemular network by aromatic π(sac)···π(pyz) stacking interactions. The FTIR spectrum of [Ag(sac)(pyz)] _n has been recorded in the region and 4,000–400 cm^?1. The optimized geometry, frequency, and intensity of the vibrational bands of [Ag(sac)(pyz)] _n were obtained by density functional theory (DFT) at the B3LYP level. The vibrational frequencies were calculated and the scaled values have been compared with the experimental FTIR data. The observed and calculated frequencies are found to be in good agreement.     

A comparative study of thermal properties of sinocalamus affinis and moso bamboo

Moso bamboo (Phyllostachys pubescens) and sinocalamus affinis (Phyllostachys heterocycla) were used in the research. Thermogravimetry (TG), a combination of TG and Fourier transform infrared spectrometer (TG–FTIR), X-ray diffraction (XRD), and differential thermal analysis (DTA) were used to investigate thermal decomposition of bamboo. The calorific value and smoke release process of both bamboos were also tested, respectively. The results from TG indicated that degradation process of sinocalamus affinis and moso bamboo was similar, but their degradation temperatures were different. The main decomposition occurred in the second step and about 68.70 and 64.63% masses degraded for sinocalamus affinis and moso bamboo, whose temperature of maximum mass loss was 319 and 339 °C, respectively. DTA curve showed that the thermal decomposition of both bamboos was an absorbance heat process. TG–FTIR analysis showed that the main pyrolysis products of both bamboos were similar, including absorbed water (H₂O), methane gas (CH₄), carbon dioxide (CO₂), acids and aldehydes, ammonia gas (NH₃). The calorific value of moso bamboo (19,291 J g^?1 K^?1) was higher than that of sinocalamus affinis (18,082 J g^?1 K^?1). The initial time of smoke release process of moso bamboo was later, and its maximum smoke density was higher than that of sinocalamus affinis. The difference was probably attributed to different compositions and structure of sinocalamus affinis and moso bamboo. The results from this research are very helpful to better design manufacturing process of bio-energy, made from bamboo, by gasification and pyrolysis methods.     

Orientation dependence of the dielectric and piezoelectric properties for the Ba0.98Ca0.02Ti0.96Sn0.04O3 thin films

Lead free Ba_0.98Ca_0.02Ti_0.96Sn_0.04O₃ (BCST) thin films with (110), (111) and (001) orientations were processed via chemical solution deposition, and effects of orientation on the dielectric and piezoelectric properties were investigated in some aspects. The (110) orientated BCST thin films exhibit highest Curie temperature (T _c of 85 °C) and lowest dielectric loss (tan δ of 0.02). While, the (111) orientated BCST thin films exhibit highest dielectric tunability (74 %) and largest piezoelectric coefficient (d ₃₃ of 78 pm/V), which indicate that it is a promising lead-free replacement for lead-based applications. The anisotropic dielectric and piezoelectric properties in the three kinds of oriented BCST films has been attributed to the difference of structure, in-plane stress and polarization rotation in orientation engineered BCST films. This work clearly reveals the dielectric and piezoelectric properties of BCST films exhibit a strong sensitivity to orientation.     

Investigation of structural,rheological and thermal properties of PMMA/ONi-Al LDH nanocomposites synthesized <Emphasis Type="Italic">via</Emphasis> solvent blending method: Effect of LDH loading

This article addresses the synthesis of organically tailored Ni-Al layered double hydroxide (ONi-Al LDH) and its use in the fabrication of exfoliated poly(methyl methacrylate) (PMMA) nanocomposites. The pristine Ni-Al LDH was initially synthesized by co-precipitation method and subsequently modified using sodium dodecyl sulfate to obtain ONi-Al LDH. Nanocomposites of PMMA containing various amounts of modified Ni-Al LDH (3 wt%-7 wt%) were synthesized via solvent blending method to investigate the influence of LDH content on the properties of PMMA matrix. Several characterization methods such as X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), rheological analysis, differential scanning calorimetry (DSC) and thermo gravimetric analysis (TGA), were employed to examine the structural, viscoelastic and thermal properties of PMMA/OLDH nanocomposites. The results of XRD and TEM examination confirm the formation of partially exfoliated PMMA/OLDH nanocomposites. The FTIR results elucidate that the characteristic bands for both pure PMMA and modified LDH are present in the spectra of PMMA/OLDH nanocomposites. Rheological analyses were carried out to examine the adhesion between polymer matrix and fillers present in the nanocomposite sample. The TGA data indicate that the PMMA nanocomposites exhibit higher thermal stability when compared to pure PMMA. The thermal decomposition temperature of PMMA/OLDH nanocomposites increases by 28 K compared to that of pure PMMA at 15% weight loss as a point of reference. In comparison with pure PMMA, the PMMA nanocomposite containing 7 wt% LDH demonstrates improved glass transition temperature (T _g) of around 3 K. The activation energy (E _a), reaction orders (n) and reaction mechanism of thermal degradation of PMMA/OLDH nanocomposites were evaluated using different kinetic models. Water uptake capacity of the PMMA/OLDH nanocomposites is less than that of the pure PMMA.     

Preparation,Tg improvement,and thermal stability enhancement mechanism of soluble poly(methyl methacrylate) nanocomposites by incorporating octavinyl polyhedral oligomeric silsesquioxanes

The soluble poly(methyl methacrylate‐co‐octavinyl‐polyhedral oligomeric silsesquioxane) (PMMA–POSS) hybrid nanocomposites with improved T_g and high thermal stability were synthesized by common free radical polymerization and characterized using FTIR, high‐resolution ¹H NMR, ²⁹Si NMR, GPC, DSC, and TGA. The POSS contents in the nanocomposites were determined based on FTIR spectrum, revealing that it can be effectively adjusted by varying the feed ratio of POSS in the hybrid composites. On the basis of the ¹H NMR analysis, the number of the reacted vinyl groups on each POSS molecules was determined to be about 6–8. The DSC and TGA measurements indicated that the hybrid nanocomposites had higher T_g and better thermal properties than the pure PMMA homopolymer. The T_g increase mechanism was investigated using FTIR, displaying that the dipole–dipole interaction between PMMA and POSS also plays very important role to the T_g improvement besides the molecular motion hindrance from the hybrid structure. The thermal stability enhances with increase of POSS content, which is mainly attributed to the incorporation of nanoscale inorganic POSS uniformly dispersed at molecular level. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5308–5317, 2007     

Synthesis of nanostructured titania/zirconia membrane and investigation of its physical separation and photocatalytic properties in treatment of textile industries wastewater

Nanostructured TiO₂/ZrO₂ composite membranes with varying compositions were obtained by sol–gel technique. The influence of 0–30 mol% zirconia doping on microstructure, water permeability, photocatalytic and physical separation properties, removal of methyl violet of textile industries wastewater and thermal and mechanical stability of titania/zirconia composite membranes was described. Firstly, alumina supports were coated with TiO₂ intermediate layers using the colloidal sol–gel route. The TiO₂/ZrO₂ composite sols were prepared via a polymeric sol–gel method and dip-coated on TiO₂ intermediate layer. The samples were characterized by DLS, TG-DTA, XRD, FTIR, BET-BJH, UV–visible, SEM, TEM and AFM. It was shown that zirconia retards the phase transformation of anatase to rutile until at least 700 °C. The minimum pore size and maximum surface area obtained were 1.2 nm and 153 m²/g, respectively, attributed to the sample with 20 mol% zirconia. The mechanical strength of titania membranes was significantly improved by addition of zirconia. The most methyl violet removal efficiency obtained, with and without UV-irradiation, is 80.8 and 72.6%, respectively, attributed to the sample with 20 mol% zirconia.     

Effect of Tb content on microstructure and ferroelectric properties of Bi4−x Tb x Ti3O12 thin films grown by sol–gel method

The effects of Tb substitution on the structural and electrical properties of ferroelectric Bi₄Ti₃O₁₂ (BTO) thin films grown on Pt/TiO₂/SiO₂/Si substrates by a sol–gel process have been reported. X-ray diffraction indicated A-site Tb substitutions did not change the polycrystalline bi-layered Aurivillius structure of the BTO, but a lattice distortion was observed. The leakage current behavior at room temperature of the films was studied and it was found that the leakage current density decreased from 10^?2 to 10^?4 A/cm² with the increase of x under 150 kV/cm. The remnant polarization (2P _r ) and dielectric constant (ε _r) increase firstly and then decreases with the increase of the Tb content. We observed a substantial increase in the remnant polarization (2P _r ) with Tb substitution and obtained a maximum value of~60 μC/cm² at an applied electric field of 500 kV/cm for x = 0.4. Moreover, this BTT-0.4 capacitor did not show fatigue behaviors after 1.0 × 10¹⁰ switching cycles, suggesting an anti-fatigue character.     

Crystal growth, structural, thermal, and dielectric characterization of Tutton salt (NH4)2Fe(SO4)2·6H2O crystals

A good quality single crystal of Tutton salt, (NH₄)₂Fe(SO₄)₂·6H₂O, with dimensions 6 × 7 × 3 mm³ was successfully grown by the slow evaporation growth technique at ambient temperature. The grown crystal was subjected to single crystal X-ray diffraction study which confirms that the grown crystal is monoclinic in nature with the space group P2₁/c. Optical absorption spectrum reveals that the grown crystal has good optical transparency in the entire visible region and its energy band gap was determined. The thermal behavior of the grown crystal was investigated by thermogravimetric and differential thermal analysis. The dielectric measurements were carried out to determine the dielectric behavior of the crystal.