Continuous Wavelength Sweep of External Cavity 630 nm Laser Diode without Antireflection Coating on Output Facet

We developed a simple method of continuous wavelength sweep using a commercial laser diode (LD) without antireflection (AR) coating. A 630 nm AlGalnP LD was installed in a Littrow-type external cavity. In this cavity, the LD has the same effect as an etalon, and its free spectral range can be controlled easily by the LD drive current. By scanning the grating angle of the external cavity and LD drive current simultaneously, we obtained single-mode oscillation and continuous wavelength sweep of over 22 GHz without mode hopping. This technique is simple and inexpensive because it does not need AR coating on its output facet, and does not use a servo system which requires apparatuses such as a lock-in amplifier and local oscillator.     

波长扫描法布里-珀罗干涉仪的优化设计

分析了可用于绝对距离测量的波长扫描法布里－珀罗干涉仪腔内多光束干涉对输出信号的影响, 及由此产生的相位测量误差。研究表明, 通过选择合适的腔端面反射率和参考腔长度可以减小相位测量误差。优化选择的腔面反射率为０．１０～０．１５, 参考腔长为０．９５ ｍ ｍ , 在１ ｍ ｍ 范围内系统可达到０．０５ μｍ 的测距精度。     

波长扫描法布里-泊罗光纤加速度计的研究

利用光纤传感器的独特优点 ,用波长扫描法将 Fabry- Perot干涉仪 (以下简称 FPI)和传统加速度计相结合 ,得到了较好的分辨率。分析了在 FPI中多光束干涉对双光束干涉的影响。实验研究表明 ,它对由振动引起的位移 (加速度 )变化相当灵敏     

Iodine stabilised He-Ne Laser

A single mode He-Ne laser operating at 6328 Å is used with an iodine cell in the cavity to detect the absorption components of iodine falling within the gain curve of the laser line. Experimental details are given for locking the frequency of the laser line with one of the hyperfine components of the iodine absorption line, using a servo-control system. The system uses the technique of detecting the first and third harmonics of the modulation frequency.     

基于扫描光纤激光器的光纤传感解调仪研究

介绍了一种基于扫描光纤激光器的光纤传感解调系统.采用氰化氢（HCN）气体吸收池作为波长参考基准,采用三次多项式拟合的方法来确定光纤F- P可调谐滤波器的波长与驱动电压的对应关系,可调谐滤波器扫描过程中对扫描电压、多路光谱信号进行同步采样,实时标定.实验结果表明,该解调系统在1 510 nm到1 590 nm波长范围内对FBG反射峰值波长的分辨率为1.4 pm,长期波长重复性达到3.2 pm.利用该系统实现了对FBG反射峰值波长和光纤EFPI传感器腔长的高准确度解调.     

基于亚波长光栅的VCSEL偏振控制研究

为了确定亚波长光栅在微电机械系统(MEMS)波长可调谐VCSEL不同位置(上DBR上表面、上DBR下表面以及内腔)中实现TE和TM偏振控制的光栅参数范围以及光栅在哪个位置时实现偏振控制最稳定,通过MATLAB建立MEMS波长可调VCSEL的模型,然后计算光栅在3种位置时上反射镜(包括空气隙和光栅)随光栅参数变化的反射率,以此来确定它们实现TE/TM稳定偏振的光栅参数范围(即高反射范围内的参数)。将各自的高反射所对应反射率减去相同光栅参数范围内TM/TE低反射对应的反射率,通过反射率差值确定光栅在哪种位置时MEMS波长可调谐VCSEL实现偏振是最稳定的。最后得出的结论是光栅在上DBR下表面几乎无法控制TM偏振,而将光栅放置于内腔中,无论是在TE偏振控制上还是TM偏振上都是最稳定的。在实现TE偏振稳定的参数范围内,TE的阈值增益比TM最小少10 cm~(-1);而在实现TM偏振稳定时,在TE偏振稳定的参数范围内,TE的阈值增益比TM最小少5 cm~(-1)。     

EIT as a tool to observe dual wavelength operation of a semiconductor laser

We propose a simplified technique for dual wavelength operation of an extended cavity semiconductor laser, and its characterization using electromagnetically induced transparency (EIT). In this laser cavity scheme light beam is made converging before it incidences on the cavity grating. The converging angle of the beam creates two longitudinal oscillating modes of resonating cavity. Frequency separation between the longitudinal modes are measured with the help of beat frequency generation in a photodiode and creating pair of EIT spectra in Rb vapor. The pair of EIT dips that are generated due to dual wavelength of this laser (that is used as control laser) can be used to estimate frequency difference between the generated wavelengths. Width of EIT spectra can be used to estimate linewidth of individual wavelength components.     

基于F-P标准具的固体激光可调线宽控制技术

钠导星激光研制需激光线宽在一定范围内可调节。开展了F-P标准具压窄线宽数值模拟,设计一台高光束质量基横模线偏振激光输出全固态1064 nm激光器作为实验装置,结合激光器输出光谱特性进行计算。根据计算结果采用不同规格的单标准具、组合双标准具实现了激光线宽在0.75 ~2.83 GHz范围内的离散调节控制。在标准具未控温情况下,不同线宽时激光中心波长保持1064.58 nm,30 min内波长漂移量小于3 pm。     

Grating-Stabilized External Cavity Diode Lasers for Raman Spectroscopy—A Review

Abstract: Conventional Raman techniques require a continuous-wave laser with stabilized wavelength, narrow line width, and sufficient output power. Due to their miniature size and low cost, diode lasers are good choice as light sources for Raman spectroscopy, especially when compact and portable instruments are needed. However, a solitary multimode diode laser has certain drawbacks that limit its use for Raman application. To circumvent these drawbacks, an external cavity can be coupled to the active gain medium of the diode to enhance the laser performance. A grating-based external cavity allows the laser to operate in a single longitudinal mode with greatly reduced line width and stabilized wavelength. This article examines the fundamentals of semiconductor lasers to show the necessity of operating diode lasers in an external cavity for Raman applications. Two feedback grating-based external cavity diode laser (ECDL) designs, viz. Littrow and Littman-Metcalf configurations, are explained. Historic and recent progress in the development of ECDL devices is reported. An updated summary of ECDL-equipped Raman systems applied to fields such as in vivo biomedical studies and in situ process/quality control is provided. Topics on mode-hop-free continuous scanning, wavelength stabilization, and dealing with ambient conditions are discussed.     

程控宽带连续调谐外腔半导体激光器特性分析

对宽带调谐外腔半导体激光器进行了理论及实验研究,分析了其最大调谐范围和连续调谐条件,为宽带可调谐激光器的设计提供了依据。完成了实用化的程控宽带连续调上腔激光器,该器件调谐范围超过７５ｎｍ,波长重复性精度为１ｎｍ,分辨率为０．０１ｎｍ。     

Surface Shape Measurement by Wavelength Scanning Interferometry Using an Electronically Tuned Ti:sapphire Laser

We developed a high speed and high resolution surface shape measurement system based on wavelength scanning interferometry with an electronically tuned Ti:sapphire laser. This laser emits pulses and the wavelength of each pulse can be tuned arbitrarily within 680 nm and 1056 nm. We also designed a high speed multiport CCD camera as a detector. This camera is synchronized with wavelength scanning of the laser at the frequency of 250 Hz. We could measure the object shape with a height resolution of 3.05 μm at the tuning range from 740.0 nm to 842.3 nm. By simple parabolic curve fitting to the Fourier peak of interference signals from each CCD pixel, the height resolution has been improved to the order of submicrometers.     

分布式反馈激光器动态扫描光纤布拉格光栅波长解调系统

通过对该系统采集到的法布里-珀罗(F-P)标准具透射谱和光纤布拉格光栅(FBG)传感器反射谱进行寻峰算法以及拟合算法的研究,采用C语言编程和LabVIEW编程相结合的方式,实现了FBG波长信号的解调。其中,由于系统采集到的F-P透射谱和FBG反射谱线时域信号数据都由离散点构成,且在3dB带宽内均符合高斯曲线分布,采用高斯拟合对采集到的信号数据进行寻峰处理,提高系统精度;又由于分布式反馈(DFB)激光器的波长扫描存在着一定的非线性,采用二项式拟合对DFB激光器的波长扫描曲线进行拟合,以降低其非线性导致的误差。另外,设置一路标准FBG传感通道用于波长校准。实验研究表明该系统稳定性良好,波长测量范围为1 550.012~1 554.812nm,分辨力为1pm,精度为±10pm,验证了该系统可用于FBG波长信号检测的可行性。     

改善外腔半导体激光器调谐特性的新方法

基于原有的Littman结构外腔半导体激光器,提出采用一种新的光学方法来实现波长调谐。该方法采用了包含一个旋转楔形棱镜的“光杠杆”系统来降低调谐的机械要求,提高波长选择精度。通过选择不同的楔形棱镜顶角和光线入射角,机械要求可以降低1～2个数量级,波长选择精度也得到相同量级的提高。该方法使Littman结构外腔半导体激光器的调谐特性得到极大的改善,并大大降低了震动的敏感性。     

ACTIVE CONTROL OF PRESSURE FLUCTUATIONS DUE TO FLOW OVER HELMHOLTZ RESONATORS

Grazing flows over Helmholtz resonators may result in self-sustained flow oscillations at the Helmholtz acoustic resonance frequency of the cavity system. The associated pressure fluctuations may be undesirable. Many solutions have been proposed to solve this problem including, for example, leading edge spoilers, trailing edge deflectors, and leading edge flow diffusers. Most of these control devices are “passive”, i.e., they do not involve dynamic control systems. Active control methods, which do require dynamic controls, have been implemented with success for different cases of flow instabilities. Previous investigations of the control of flow-excited cavity resonance have used mainly one or more loudspeakers located within the cavity wall. In the present study, oscillated spoilers hinged near the leading edge of the cavity orifice were used. Experiments were performed using a cavity installed within the test section wall of a wind tunnel. A microphone located within the cavity was used as the feedback sensor. A loop shaping feedback control design methodology was used in order to ensure robust controller performance over varying flow conditions. Cavity pressure level attenuation of up to 20dB was achieved around the critical velocity (i.e., the velocity for which the fundamental excitation frequency matches the Helmholtz resonance frequency of the cavity), relative to the level in the presence of the spoiler held stationary. The required actuation effort was small. The spoiler peak displacement was typically only 4% of the mean spoiler angle (approximately 1′). The control scheme was found to provide robust performance for transient operating conditions. Oscillated leading edge spoilers offer potential advantages over loudspeakers for cavity resonance control, including a reduced encumbrance (especially for low-frequency applications), and a reduced actuation effort.     

空间正交三轴激光陀螺的调腔技术

通过分析传统激光陀螺的调腔方式,提出了激光陀螺应在实际工作条件(具有增益能力状态)下进行调腔的观点,以及通过控制其腔长或光程长来控制反射镜的反射方向的调腔方法,并相应地设计了新的腔长控制镜结构。通过全面扫描的方式,找出了空间正交三轴激光陀螺的三腔在高质量运转时的最佳角度控制参数,解决了空间三轴激光陀螺高精度调腔的难题。     

Real-space observation of ultraslow light in photonic crystal waveguides

We show the real-space observation of fast and slow pulses propagating inside a photonic crystal waveguide by time-resolved near-field scanning optical microscopy. Local phase and group velocities of modes are measured. For a specific optical frequency we observe a localized pattern associated with a flat band in the dispersion diagram. During at least 3 ps, movement of this field is hardly discernible: its group velocity would be at most c/1000. The huge trapping times without the use of a cavity reveal new perspectives for dispersion and time control within photonic crystals.     

光纤光栅激光器激射波长的研究

一般认为，用光纤光栅作选频元件的光纤激光器，激射波长与光纤光栅中心反射波长一致，本文报道了不同的实验研究结果。通过细致的实验研究，发现光纤光栅激光器激射波长相对于光纤光栅中心反射波长有一定的偏移。激射波长可以出现在光栅中心反射波长的长波端，也可以出现在其短波端。对不同腔结构的掺镱、掺铒光纤光栅激光器的深入研究证明，谐振腔的各向异性对激光器的激射波长偏移起到决定性的作用，波长最大偏移量主要受限于光纤光栅的反射带宽。通过激光腔内的偏振控制器改变谐振腔的各向异性，可以在光纤光栅的反射带宽内控制激射波长的位置。     

Short‐wavelength infrared defect emission as a probe of degradation processes in 980 nm single‐mode diode lasers

Infrared emission from 980‐nm single‐mode high power diode lasers is recorded and analyzed in the wavelength range from 0.8 to 8.0 μm. A pronounced short‐wavelength infrared (SWIR) emission band with a maximum at 1.3 μm originates from defect states located in the waveguide of the devices. The SWIR intensity is a measure of the non‐equilibrium carrier concentration in the waveguide, allowing for a non‐destructive waveguide mapping in spatially resolved detection schemes. The potential of this approach is demonstrated by measuring spatially resolved profiles of SWIR emission and correlating them with mid‐wavelength infrared (MWIR) thermal emission along the cavity of devices undergoing repeated catastrophic optical damage. The enhancement of SWIR emission in the damaged parts of the cavity is due to a locally enhanced carrier density in the waveguide and allows for an analysis of the spatial damage patterns. The figure shows a side view of a diode laser during catastrophic degradation as recorded by a thermocamera within 5 successive current pulses. The geometry of the device is given in grayscale. The position of the laser chip is indicated by the dotted line. The thermal signatures of the internal degradation of the diode laser are overlaid in color. The bi‐directional spread of the damage along the laser cavity is clearly visible.     

一种中红外腔增强甲醛检测系统的研制

介绍了研制的一种基于共轴锁模腔增强吸收光谱技术的中红外甲醛气体检测系统。系统采用了发射中心波长为3.6 μm的带间级联激光器为光源,以高精度F-P谐振腔作为气体反应池,通过激光在谐振腔内的多次反射极大地提高了有效吸收路径。为了实现甲醛检测,利用Pound-Drever-Hall（PDH）技术将激光频率和腔谐振频率锁定至波长为3 599.08 nm的甲醛吸收峰上。实验发现,谐振腔腔长容易受到外界环境的影响产生变化,导致系统失去锁定,产生测量误差;为了抑制这一现象,提高系统的准确性和抗干扰性,采用了动态PDH锁定技术,通过低频锯齿波信号对腔长进行小范围内的周期性调制,使得腔谐振频率在目标气体吸收峰附近缓慢来回变化;通过选择合适的扫描范围使得在扫描过程中激光与谐振腔保持频率锁定。系统通过光电探测器采集谐振腔透射光强信号,通过对腔透射信号进行拟合计算来确定甲醛浓度。为了验证检测系统的有效性、评估系统的性能,采用质量流量计配备了6种不同浓度的甲醛气体样品并开展了甲醛吸收光谱测量实验、系统标定实验和稳定性实验。实验结果显示,在0～10 mL·L-1范围内,腔透射信号拟合值与甲醛浓度之间呈现出良好的线性关系;通过Allan方差分析得到当积分时间为1 s时系统检测下限为52.8 nL·L-1,积分时间为14 s时检测下限可以降至3.3 nL·L-1。此外,通过增加谐振腔的腔镜反射率和腔长可以提高有效吸收路径,进一步降低检测下限。该系统灵敏度高、响应速度快,具有较好的抗干扰性和长期稳定性,在痕量甲醛检测方面具有广阔的应用前景。     

测量大口径光学元件反射率用精密扫描系统误差分析

为测量高能激光传输系统中大口径高反射率光学元件的反射率,设计了一种大口径光学元件二维扫描的精密测量系统。介绍了该系统的结构及其工作原理,分析了影响系统测量精度的因素,从理论上分析了扫描系统的系统误差对测量精度的影响,结果表明在垂直于光束传播方向上,水平偏差在0.29 mm时,测量误差在10-6量级;腔长的变化量较小时,可通过对衰荡腔腔镜的调节,实现对旋转轴偏差的补偿及对系统的精细调节。通过拟合处理光强与时间的数据得到对应的一次指数函数拟合曲线,并通过计算得到衰荡时间和反射率,经过对比分析可知,该误差分析方法能比较有效地测量腔镜的反射率,并能减小实验数据本身带来的误差。