Surface modification of acrylate intraocular lenses with dielectric barrier discharge plasma at atmospheric pressure

Surface modification with dielectric barrier discharge (DBD) plasma was carried out at atmospheric pressure (argon as the discharge gas) to improve the biocompatibility of hydrophobic acrylate intraocular lens (IOL). Changes of the plasma-treated IOL surface in chemical composition, morphology and hydrophilicity were comprehensively evaluated by X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM) and water contact angle (WCA) measurements. The surface biocompatibility of the untreated and plasma-treated IOLs was compared with the adhesion behavior of platelets, macrophages and lens epithelial cells (LECs) in vitro. After DBD plasma treatment, the hydrophilicity of the IOL surface was obviously improved. The changes in WCA with treatment extension may be attributed to both the introduction of oxygen or/and nitrogen-containing polar groups and the increase of surface roughness induced by plasma etching effect. The existence of low molecular weight oxidized material (LMWOM) was proved on the plasmatreated IOL which was caused by the chain scission effect of the plasma treatment. The plasma-treated IOLs resisted the adhesion of platelets and macrophages significantly. The LECs spreading and proliferation were postponed on the IOLs plasma-treated for more than 180 s, with a well maintained epithelial phenotype of LECs. The IOL biocompatibility was improved after the DBD plasma treatment. We speculate that slighter foreign-body reaction and later incidence of anterior capsule opacification (ACO) may be expected after implantation of the argon DBD plasma-treated IOL. Supported by the Zhejiang Natural Science Foundation of China (Grant No. 2004C23003)     

Surface characterization of the SiOx films prepared by a remote atmospheric pressure plasma jet

The deposition rate and surface properties of SiO_x films were prepared and investigated using remote atmospheric pressure plasma (APP) jet. The APP, generated with low frequency power at 16 kHz, was fed with tetraethoxysilane (TEOS)/air gas mixture. After deposition, the SiO_x films were analyzed for chemical characteristics, elemental composition, surface morphology, and hardness. It was found that the deposition substrate temperature is the key factor to affect the deposition rate of remote APP chemical vapor deposition process. Fourier transform infrared (FTIR) spectra indicated that APP deposited SiO_x films are an inorganic feature. XPS examination revealed that the SiO_x films contained approximately 30% silicon, 58% oxygen and 12% carbon. Atomic forced microscopy (AFM) analysis results indicated a smooth surface of SiO_x films in deposition under higher substrate temperature. Also, pencil hardness tests indicated that the hardness of APP deposited SiO_x films was greatly improved with increasing substrate temperatures. Copyright © 2008 John Wiley & Sons, Ltd.     

Surface modifications of PET in argon atmospheric pressure plasma: Gas flow rate effect

The correlation between plasma optical properties and the treated polyethylene terephthalate (PET) surface characteristics have been studied at various Ar flow rate. The rotational T_rot and vibrational T_vib temperatures of APPJ were determined from SPS emission band. The pristine and plasma-treated PET surfaces were characterized by several techniques including X-ray photoelectrons spectroscopy (XPS), Raman spectroscopy, contact angle (CA), and atomic force microscope (AFM). The CA decreased rapidly in the flow rate range 1–3 L/min and weakly dependent as flow rate > 3 L/min. XPS results showed that C 1s % of plasma-treated PET surfaces decreases and has a minimum for samples treated at 3–4 L/min, while O 1s has a maximum at the same flow rate range. The carbon C 1s peak of pristine and plasma treated PET samples resolved into five subcomponents: C–C, C–O, C=O, O–C=O, and π–π bonds with variable percentage ratio accordance to the plasma gas flow rate. Raman data revealed a partial loss in the crystallinity of the treated PET samples and also confirm the incremental of C–O band at Ar flow rate of 3 L/min. AFM images showed that the surface roughness of treated PET films increases as Ar flow rate increases.     

Deposition of thin films and coatings by atmospheric pressure vapor plasma jet

An atmospheric pressure plasma jet generated by inductively coupled RF discharge and containing vapors of silicon compounds in argon-carrier gas was used to deposit a-Si∶H, a-Si∶(H, O), and a-SiC film. Rapid deposition up to 10 μm/min results from efficient material transport and is limited mainly by rates of surface reactions. Morphology, structure, and composition of deposits were studied.     

Surface modification of chromatography adsorbents by low temperature low pressure plasma

In this study we show how low temperature glow discharge plasma can be used to prepare bi-layered chromatography adsorbents with non-adsorptive exteriors. The commercial strong anion exchange expanded bed chromatography matrix, Q HyperZ, was treated with plasmas in one of two general ways. Using a purpose-designed rotating reactor, plasmas were employed to either: (i) remove anion exchange ligands at or close to the exterior surface of Q HyperZ, and replace them with polar oxygen containing functions (‘plasma etching and oxidation’); or (ii) bury the same surface exposed ligands beneath thin polymer coatings (‘plasma polymerization coating’) using appropriate monomers (vinyl acetate, vinyl pyrrolidone, safrole) and argon as the carrier gas. X-ray photoelectron spectroscopy analysis (first ∼10 nm depth) of Q HyperZ before and after the various plasma treatments confirmed that substantial changes to the elemental composition of Q HyperZ's exterior had been inflicted in all cases. The atomic percent changes in carbon, nitrogen, oxygen, yttrium and zirconium observed after being exposed to air plasma etching were entirely consistent with: the removal of pendant Q (trimethylammonium) functions; increased exposure of the underlying yttrium-stabilised zirconia shell; and introduction of hydroxyl and carbonyl functions. Following plasma polymerization treatments (with all three monomers tested), the increased atomic percent levels of carbon and parallel drops in nitrogen, yttrium and zirconium provided clear evidence that thin polymer coats had been created at the exteriors of Q HyperZ adsorbent particles. No changes in adsorbent size and surface morphology, nor any evidence of plasma-induced damage could be discerned from scanning electron micrographs, light micrographs and measurements of particle size distributions following 3 h exposure to air (220 V; 35.8 W L⁻¹) or ‘vinyl acetate/argon’ (170 V; 16.5 W L⁻¹) plasmas. Losses in bulk chloride exchange capacity before and after exposure to plasmas enabled effective modification depths within hydrated Q HyperZ adsorbent particles to be calculated as 0.2–1.2 μm, depending on the conditions applied. The depth of plasma induced alteration was strongly influenced by the power input and size of the treated batch, i.e. dropping the power or increasing the batch size resulted in reduced plasma penetration and therefore shallower modification. The selectivity of ‘surface vs. core’ modification imparted to Q HyperZ by the various plasma treatments was evaluated in static and dynamic binding studies employing appropriate probes, i.e. plasmid DNA, sonicated calf thymus DNA and bovine serum albumin. In static binding studies performed with adsorbents that had been exposed to plasmas at the 5 g scale (25 g L⁻¹ of plasma reactor), the highest ‘surface/core’ modification selectivity was observed for Q HyperZ that had been subjected to 3 h of air plasma etching at 220 V (35.8 W L⁻¹). This treatment removed ∼53% of ‘surface’ DNA binding at the expense of a 9.3% loss in ‘core’ protein binding. Even more impressive results were obtained in dynamic expanded bed adsorption studies conducted with Q HyperZ adsorbents that had been treated with air (220 V, 3 h) and ‘vinyl acetate/argon’ (170 V, 3 h) plasmas at 10.5 g scale (52.5 g L⁻¹ of plasma reactor). Following both plasma treatments: the 10% breakthrough capacities of the modified Q HyperZ adsorbents towards ‘surface’ binding DNA probes dropped very significantly (30–85%); the DNA induced inter-particle cross-linking and contraction of expanded beds observed during application of sonicated DNA on native Q HyperZ was completely eradicated; but the ‘core’ protein binding performance remained unchanged cf. that of the native Q HyperZ starting material.     

Surface modification of aluminium with reactive microgels

The adsorption and organisation process of reactive microgels has been investigated on technical aluminium. The aim was to replace the present chromating procedure on reactive metals like aluminium because this process was been considered as an ecological problem. By means of a two‐step emulsion polymerization with phosphate substituted monomer we have obtained polymeric nano‐particles with phosphate groups on the surface. The core is synthesized by copolymerization from styrene (St) and butyl acrylate (BuA). The results of several analytical methods like contact angle SEM or TEM measurements showed, that these microgels were able to adsorb spontaneously onto the substrate surface and subsequently a structured molecular order was formed. The properties of the adsorbed microgel layers were confirmed by industrial linked adhesion and corrosion tests.     

Surface treatment and characterization of ITO thin films using atmospheric pressure plasma for organic light emitting diodes

Ar atmospheric pressure plasma (APP) was used to treat indium-tin-oxide (ITO). The plasma conditions were varied to treat the ITO surface, e.g., plasma treatment time, RF power, flow rate, and the plasma outlet-to-sample distance. The plasma effectiveness was measured by the contact angle. The change in the surface energy calculated with the Owens-Wendt method mainly arises from the polar component. The dynamic contact angle measurements show that APP-treated surface showed considerably lower hysteresis in the water and ethylene glycol but there was no change in hysteresis in methylene iodide compared with the untreated ITO. Atomic force microscopy showed that the Ar APP-treated surface sharply decreased the surface roughness and showed a similar morphology as the untreated ITO. X-ray photoelectron spectroscopy showed that the Ar APP treatment not only effectively removed carbon contamination from the surface but also introduced oxygen. Therefore, it is believed that the APP treatment modifies the physico-chemical properties of ITO, which can in turn improve the performance of the organic light-emitting diodes.     

大气压等离子体射流重整CH4-CO2制合成气

采用大气压等离子体射流,以CH₄和CO^₂直接作为放电气体进行常压下重整制合成气的实验研究,考察了等离子体射流的放电特征及放电距离、放电功率、原料气配比和流量对反应的影响。结果表明,该等离子体具有放电稳定、均匀的特征。重整反应的主要产物为合成气,只有少量的H₂O和积炭生成。优化的反应条件为放电距离为9mm,CH₄和CO₂的摩尔比为4/6。当原料气流量为1000mL/min,放电功率为88.4W时,CH4和CO₂的最高转化率为分别为94.99%和87.23%。甲烷和二氧化碳的转化率随放电功率的增加而增加,随流量的增加而减少。     

大气压等离子体射流重整CH_4-CO_2制合成气

采用大气压等离子体射流,以CH4和CO2直接作为放电气体进行常压下重整制合成气的实验研究,考察了等离子体射流的放电特征及放电距离、放电功率、原料气配比和流量对反应的影响。结果表明,该等离子体具有放电稳定、均匀的特征。重整反应的主要产物为合成气,只有少量的H2O和积炭生成。优化的反应条件为放电距离为9 mm,CH4和CO2的摩尔比为4/6。当原料气流量为1 000 mL/min,放电功率为88.4 W时,CH4和CO2的最高转化率为分别为94.99%和87.23%。甲烷和二氧化碳的转化率随放电功率的增加而增加,随流量的增加而减少。     

Comparison of the surface characteristics of polypropylene films treated by Ar and mixed gas (Ar/O2) atmospheric pressure plasma

In an attempt to modify the hydrophobic surface properties of polypropylene (PP) films, this study examined the optimum process parameters of atmospheric pressure plasma (APP) using Ar gas. Under optimized conditions, the effects of a mixed gas (Ar/O2) plasma treatment on the surface-free energy of a PP film were investigated as a function of the O2 content. The polar contribution of the surface-free energy of the PP film increased with increasing O2 content in the gas mixture. However, slightly more oxygen-containing polar functional groups such as CO, CO, and COO were introduced on the PP film surface by the Ar gas only rather than by the Ar/O2 gas mixture. In addition, AFM analysis showed that the Ar plasma treatment of the PP film produced the smoothest surface as a result of the relatively homogeneous etching process.     

Selective determination of organofluorine compounds by capillary column gas chromatography with an atmospheric pressure helium microwave-induced plasma detector

Fluorinated analogs of compounds typical of those found in metabolic and other biological studies are detected with high selectivity using a gas chromatograph/microwave-induced plasma detector (GC-MIPD), which permits fluorine-selective detection by monitoring the emission at 685.6 nm. Using the described atmospheric pressure helium-sustained plasma detector, the minimum detectable level, fluorine selectivity (relative to carbon), and linear dynamic range of this GC-MIPD system were determined to be 4.8 pg-F/s, 1060, and 5000, respectively. The utility of this GC-MIPD system for the selective detection of organofluorine compounds is demonstrated by its application in the analysis of the metabolic fate of a fluorinated substrate administered to a mixture of wheat germ phosphatase and potato apyrase, as well as by analysis of synthetic mixtures.     

Surface modification of EPDM rubber by plasma treatment

The effect of argon, oxygen, and nitrogen plasma treatment of solvent cast EPDM rubber films has been investigated by means of atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and surface energy measurements. Plasma treatment leads to changes in the surface energy from 25 to 70 mN/m. Treatment conditions influenced both the changes in surface energy and the stability, and it became more difficult to obtain good contact angle measurements after longer (> ca. 4 min) treatment times, probably because of an increasingly uneven surface structure. XPS analyses revealed that up to 20 at. % oxygen can be easily incorporated and that variations of approximately 5% can be controlled by the plasma conditions. Oxygen was mainly found in hydroxyl groups, but also as carbonyl and carboxyl. XPS analyses showed more stable surfaces than expected from contact angles, probably because XPS analysis is less surface sensitive than contact angle measurements. AFM measurements revealed different surface structures with the three gases. The surface roughness increased generally with treatment time, and dramatic changes could be observed at longer times. At short times, surface energy changes were much faster than the changes in surface structure, showing that plasma treatment conditions can be utilized to tailor both surface energies and surface structure of EPDM rubber.     

Enhanced lithium-ion intercalation and conduction of transparent tantalum oxide films by lithium addition with an atmospheric pressure plasma jet

An investigation is conducted on enhancing lithium-ion intercalation and conduction performance of transparent organo tantalum oxide (TaO _y C _z ) films, by addition of lithium via a fast co-synthesis onto 40 Ω/□ flexible polyethylene terephthalate/indium tin oxide substrates at the short exposed durations of 33–34 s, using an atmospheric pressure plasma jet (APPJ) at various mixed concentrations of tantalum ethoxide [Ta(OC₂H₅)₅] and lithium tert-butoxide [(CH₃)₃COLi] precursors. Transparent organo-lithiated tantalum oxide (Li _x TaO _y C _z ) films expose noteworthy Li⁺ ion intercalation and conduction performance for 200 cycles of reversible Li⁺ ion intercalation and deintercalation in a 1 M LiClO₄-propylene carbonate electrolyte, by switching measurements with a potential sweep from ?1.25 to 1.25 V at a scan rate of 50 mV/s and a potential step at ?1.25 and 1.25 V, even after being bent 360° around a 2.5-cm diameter rod for 1000 cycles. The Li⁺ ionic diffusion coefficient and conductivity of 6.2?×?10^?10 cm²/s and 6.0?×?10^?11 S/cm for TaO _y C _z films are greatly progressed of up to 9.6?×?10^?10 cm²/s and 7.8?×?10^?9 S/cm for Li _x TaO _y C _z films by co-synthesis with an APPJ.     

Ar等离子体对氟橡胶F2311表面的改性

利用氩气等离子对氟橡胶F2311进行表面亲水改性处理，通过接触角测量、X射线光电子能谱(XPS)对改性后的F2311进行分析，结果表明氩气等离子体处理可通过等离子体聚合在F2311表面形成含碳、氧、氮的覆盖层，可较好地改善F2311的表面亲水性，并有较好的表面动力学性质，获得的表面亲水性可以保持很长时间。     

Surface modification of chlorobutyl rubber by plasma polymerization

Radio frequency (r.f.) plasma polymerization of vinylidene fluoride (CH₂CF₂) has been used to modify the surface properties of chlorobutyl rubber. FTIR-ATR spectra of the treated rubbers and transmission spectra of plasma polymer films on NaCl windows indicated that as power increased the F/H ratio decreased. SIMS tests supported the FTIR results, and showed that the decrease in the F/H ratio was due to a decrease in the amount of F and an increase in the amount of H in the plasma polymer. Sliding friction measurements showed a reduction in the coefficient of friction (μ) from 3.7 for the untreated rubber to values ranging between 0.4 and 1.9 for the plasma-treated rubbers. There did not appear to be any correlation between the coefficient of friction and plasma power or monomer flow rate, and the average coefficient of friction for the plasma-treated samples was 0.9, which was lower than a commercially used silicone oil treatment (μ = 1.1–1.3). Repetitive sliding friction tests showed that the plasma- and silicone oil treated-chlorobutyl rubbers had the similar lubricating lifetimes. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 1651–1660, 1997     

Surface modification of Kapton film by plasma treatments

Kapton films were treated with seven plasmas: Ar-, N₂-, O₂-, CO-, CO₂-, NO-, and NO₂- plasmas. Surface properties and chemical composition of the plasma-treated Kapton films were investigated from the contact angle measurement, and the IR and XPS spectra. The plasmas, especially NO- and NO₂-plasma, made the Kapton film surface hydrophilic. The XPS and IR spectra showed that the plasma led to the modification of the imide groups in the Kapton film to secondary amide and carboxylate groups.     

Lithium electrochromism of atmospheric pressure plasma jet-synthesized NiO x C y thin films

Reversible lithium intercalation and deintercalation behavior of atmospheric pressure plasma jet (APPJ)-synthesized organonickel oxide (NiO _x C _y ) thin films under various substrate distances is testified in an electrolyte (1?M LiClO₄–propylene carbonate solution) at low driving voltages from ?0.5 to 1.5?V. Fast responses of 2?s bleaching at ?0.5?V and 6?s coloration at +1.5?V are accomplished for the nano-porous NiO _x C _y thin films. This study reveals that a rapid synthesis of electrochromic NiO _x C _y thin films in a single process via APPJ by 21?s is investigated. This study presents a noteworthy electrochromic performance in a light modulation with up to 43% of transmittance variation and a coloration efficiency of 36.3?cm²/C at a wavelength of 830?nm after 200?cycles of cyclic voltammetry measurements.     

Surface modification of thin polystyrene films

 The sulfonation of polystyrene (PS) films with 50 and 96% sulfuric acid as a function of time is presented. In contrast to previous literature reports, we showed that the treatment of PS films even with dilute sulfuric acid yields sulfonated surfaces after reaction times of 30 s–1 h. The hydrophilicity of the modified PS increased considerably in comparison to the unreacted PS films. X-ray photoelectron spectroscopy yielded evidence for the sulfonation of PS at the surface. Unreacted spin-coated PS films were very smooth, while modified PS showed some clumps dispersed on a flat surface, as analyzed by atomic force microscopy. The surface morphology was identified as a phase-separated system composed of domains of unreacted PS and a matrix of sulfonated PS by fluorescence microscopy using the positively charged dye rhodamine B. The adsorption of the polycation diallyldimethylammonium chloride on the sulfonated PS surface could be detected. The thickness of the adsorbed polycation was 2.2 nm. Received: 3 November 1998 Accepted in revised form: 23 February 1999     

Lithium intercalation and conduction in Fe-containing tantalum oxide films synthesized with an atmospheric pressure plasma jet

Journal of Solid State Electrochemistry - Lithium ionic intercalation and conduction performance of tantalum oxides films improved by adding with iron oxides using an atmospheric pressure plasma...