Wavelength tunable linear cavity cladding pump Er<Superscript>3+</Superscript>/Yb<Superscript>3+</Superscript>co-doped fiber laser operating in L-band

We have demonstrated a novel tunable linear cavity Er³⁺/Yb³⁺ co-doped fiber laser, which utilizes amplified spontaneous emission as a secondary pump source so that it can operate in L-band. The tuning wavelength range can be up to 34 nm, from 1588.6 to 1622.6 nm, and the output power excursion of the laser at different wavelengths can be less than 0.4 dB by using a two sections of high-birefringence fiber loop mirror as the wavelength filter. The high output power of 200 mW is realized by using the cladding-pump.     

30-W Yb<Superscript>3+</Superscript>-pulsed fiber laser with wavelength tuning

We have investigated various pulsed operation regimes of a diode-pumped Yb³⁺-doped fiber laser with both an acoustooptic filter and a shutter inside the resonator. To imbed the polarization-sensitive acoustooptic-tunable spectral filter into the polarization-nonmaintaining resonator, based on an “isotropic” single-mode fiber without “polarization’ losses, we have used a CaCO₃ single-crystal nondispersive thermostable polarization splitter. Stable smooth bell-shaped laser pulses were obtained in the Q-switch generation regime across the entire wavelength tuning band. Their duration depended on the resonator travel time and their repetition rate was determined exclusively by the outer high-frequency generator controlling the acoustooptic shutter. A pulsed laser radiation tuning bandwidth of more than 20-nm at a repetition rate band of 10–100 kHz was observed in the amplification band of the Yb³⁺-doped fiber. A stable average power of 30 W of the pulsed 70-ns 100-kHz laser radiation in a near Gaussian beam was reached by means of the two-stage amplifier based on Yb³⁺-doped fibers with an enlarged mode field diameter (14 μm). The amplifier was pumped by λ = 975 nm CW multimode laser diodes with a maximum average power of 42 W.     

Tunable,narrow linewidth,linearly polarized and gain-switched Cr<Superscript>2+</Superscript>:ZnSe laser

We demonstrate a tunable, narrow linewidth, linearly polarized and gain-switched Cr²⁺:ZnSe laser pumped by a Tm, Ho:YVO₄ laser at 10 kHz pulse repetition frequency. By setting a quartz birefringent filter with a Brewster angle in the cavity, the linearly polarized Cr²⁺:ZnSe laser can be continuously tuned from 2.45 to 2.50 μm, and the output power was almost not changed. In addition, the linewidth was compressed to about 5 nm. At the incident pump power to the crystal of 14 W, the maximum output power of 2.84 W was obtained, corresponding to a slope efficiency of 20.4%.     

Numerical analysis of stimulated Brillouin scattering in high-power double-clad fiber lasers

A theoretical analysis of stimulated Brillouin scattering (SBS) in linear cavity Yb³⁺-doped double-clad fiber lasers is presented by solving the steady-state rate equations with the SBS. The effects of cavity length, fiber core diameter, input mirror reflectivity at Stokes wavelength, Yb³⁺ concentration and laser linewidth on the SBS are discussed. Numerical results show that the SBS threshold power can be improved by shortening the cavity length, using large mode area fiber, reducing the input mirror reflectivity at Stokes wavelength, lowering the Yb³⁺ concentration and broadening the laser linewidth, and the influence of the laser linewidth on the SBS threshold power is more noticeable than other system parameters.     

Critical pump power and cross-section calculation for Yb<Superscript>3+</Superscript>-doped novel inner-clad structures

Rare-earth doped fiber lasers are now considered suitable sources for the 1.0-, 1.5-, and even 2.0-μm regions in a relatively large number of applications. In particular, Yb³⁺-doped fiber lasers have received strong interest due to its high quantum efficiency, broad tunability, and available high output power. In this work, we present results on a newly developed code for the simulation of the critical power that is required when designing double-clad high-power Yb³⁺-doped fiber lasers, which are based on novel inner-clad structures. From our results, we can also estimate σ_ep, σ_el, σ_ap, and σ_al for the aforementioned free-running laser cavities. Finally, we will formulate our predictions for feasible fiber laser cross sections.     

All-fiber ultra-narrow linewidth 50 pm Tm<Superscript>3+</Superscript>-doped double-clad fiber laser at 1948 nm

A high stability all-fiber LD-clad-pumped Tm³⁺-doped fiber laser was reported. The fiber laser had the ultra-narrow linewidth 50 pm at 1.948 μm with the maximal output power of 12.8 W. The slope efficiency was 28.9%, and threshold was 5.7 W. The double-clad Tm³⁺-doped fiber core was multi-mode, which had a demission of 25/250 μm with the core NA of 0.1 and inner-clad NA of 0.46. The high reflectivity coupler FBG was directly written into the single-mode passive photosensitive optical fiber core, which had a core diameter of 15 μm and NA of 0.1. The cavity was build-up by the high reflectivity FBG and the output fiber end Fresnel reflectivity.     

Comparison of RTP electro-optic Q-switch and acousto-optic Q-switch in Tm,Ho:GdVO<Subscript>4</Subscript> laser

We demonstrate a tunable, narrow linewidth, linearly polarized and gain-switched Cr²⁺:ZnSe laser pumped by a Tm, Ho:YVO₄ laser at 10 kHz pulse repetition frequency. By setting a quartz birefringent filter with a Brewster angle in the cavity, the linearly polarized Cr²⁺:ZnSe laser can be continuously tuned from 2.45 to 2.50 μm, and the output power was almost not changed. In addition, the linewidth was compressed to about 5 nm. At the incident pump power to the crystal of 14 W, the maximum output power of 2.84 W was obtained, corresponding to a slope efficiency of 20.4%.     

All-fiber clad-pumped Tm3+-doped fiber amplifier using high power fiber combiner

The diode laser (LD) clad-pumped 1947.6 nm continuous wave (CW) Tm³⁺-doped fiber amplifier is reported using the master oscillation power amplifier (MOPA) method. The injected seed laser is provided by an all-fiber LD-clad-pumped Tm³⁺-doped single-mode fiber laser, which has a nearly 2.4 W maximal output power and 0.1 nm ultra-narrow linewidth based on the intracore reflection FBG. Using the 25/400 μm double-clad LMA Tm³⁺-doped fiber as the gain fiber, the output maximal output power is 30.6 W from the fiber amplifier, with a slope efficiency of 39.1% respected to the LD total output power. A high power multi-mode fiber combiner is used to couple high power LD light into the gain fiber. The output wavelength is also located at 1947.6 nm, with the slightly expanded laser linewidth of 0.2 nm.     

A ceramic based Yb<Superscript>3+</Superscript>:YAG laser

We report the performance of a laser based on a 9.8% doped ceramic Yb³⁺:YAG operating in quasi-Continuous Wave (QCW) and in Continuous Wave (CW) at room temperature. The maximum output power of 9 W with a slope efficiency of 73% at 1030 nm was achieved in QCW. We investigated the problems originated from thermo-mechanical properties of the ceramic and we studied their effects on the laser per-formance finding that either the slope efficiency or the laser threshold are thermal-losses independent. Finally, we report a characterization of a low losses tunable cavity for several laser wavelengths.     

Several hundred kHz repetition rate nanosecond pulses amplification in Er–Yb co-doped fiber amplifier

We have experimentally investigated several hundred kHz repetition rate 1,550-nm nanosecond pulses amplification in Er–Yb co-doped fiber amplifier (EYDFA). The experimental setup has three stage fiber amplifiers. At the output of the second stage EYDFA, Yb³⁺ ions induced amplified spontaneous emission (Yb-ASE) is not observed owing to the low pump power. In the third stage EYDFA, a simultaneously seeded 1,064-nm continuous-wave laser is used to control Yb-ASE. Without any additional 1,064-nm signal, significantly backward Yb-ASE which caused loss-induced heat accumulation at the input port of the pump combiner can be observed. The monitored temperature at the input port of the pump combiner rapidly grows from 30 to 80 °C when the pump power is turned from 20 to 32 W. When a 196-mW forward 1,064-nm laser is added, the monitored backward Yb-ASE power is significantly declined, and the monitored temperature is kept below 35 °C. But, the additional signal caused a large power fraction at 1,064 nm in the output laser. In our experiment at the maximum pump power of 48.5 W, the total output power is 20 W with ~6.4-W 1,550-nm pulsed laser and ~13-W 1,064-nm continuous-wave laser.     

Top-hat beam Tm<Superscript>3+</Superscript>-doped fiber laser using an intracavity abrupt taper

The top-hat beam clad-pumped Tm³⁺-doped fiber laser was realized simply using an intracavity multi-mode abrupt taper. The ratio of the flat-top diameter to the spot diameter reaches 53%, with a small intensity variation less than 6%, and the top-hat beam’s half-divergence angle is only 5.3°. The fiber laser has a maximal output power of 5 W with slope efficiency of 39.7%, pumped by the 792 nm diode laser (LD). The abrupt taper is directly made on the multi-mode double-clad Tm³⁺-doped fiber near the fiber laser output end with the 0.45 ratio of taper waist diameter to fiber clad diameter, and this fiber end 4% Fresnel reflection is used to be the output coupler. The fiber laser’s high reflective coupler is an intracore multi-mode FBG, which is directly written into the multi-mode Tm³⁺-doped fiber core using femtosecond laser and phase mask, at the other fiber end. The abrupt taper has no obviously influence on the fiber laser output power, and the output laser spectrum.     

Wavelength tunable femtosecond laser based on short Er<Superscript>3+</Superscript>/Yb<Superscript>3+</Superscript> codoped phosphate fiber

A wavelength tunable laser system mode-locked by nonlinear polarization evolution based on a 3 cm-long homemade Er³⁺/Yb³⁺ codoped phosphate fiber has been reported. By simply adjusting the polarization controllers, the central wavelength of the mode-locked spectrum can be tuned over 1537.1–1563.3 nm continuously. Moreover, 264-fs pulse with 3-dB spectral width of 39.6 nm and peak power of 7.8 kW at a 7.55 MHz repetition rate is generated directly from the all-fiber ring cavity.     

Self-mixing effect in Yb3+ doped DBR fiber laser with different linewidth enhancement factor

We present a self-mixing interference model approach to stimulate the self-mixing interference in YDBR fiber laser with optical self-mixing interference operating in the weak feedback regime. The self-mixing interference model includes Yb³⁺ doped fibers pumped at 920 nm, with distributed Bragg reflector mirrors at both fiber ends and external reflector. Using the quasi-analytical YDBR fiber laser model and self-mixing three-mirror cavity model, the output power expression is deduced and the Peak-to-Peak values and asymmetry values of self-mixing waveform at different linewidth enhancement factor have been studied in detail.     

100-mW linear polarization single-frequency all-fiber seed laser for coherent Doppler lidar application

A compact short-cavity fiber laser configured with Er³⁺/Yb³⁺ highly co-doped phosphate glass fiber with stable linear polarization and single frequency output is proposed and investigated experimentally. The fiber laser is composed of a high-reflectivity fiber Bragg grating (HRFBG) and a polarization-maintaining fiber Bragg grating (PMFBG) with the matched wavelengths at 1540.3 nm, which aims at one of the center wavelengths of the atmospheric transmission windows and may be used as the local oscillator (LO) of the coherent Doppler lidar (CDL). The output power of the laser reaches more than 114-mW, the signal-to-noise ratio is larger than 70 dB and the laser linewidth is about 4.1-kHz. Moreover, the linear polarization with 40.5 dB extinction ratio, the power fluctuation of less than ± 0.25% and the frequency fluctuation of less than ± 80 MHz are also obtained. Compared with the DFB fiber laser, the proposed fiber laser is more suitable for the CDL applications.     

Threshold characteristics of linear cavity Yb-doped double-clad fiber laser

The threshold characteristics of linear cavity Yb³⁺-doped double-clad fiber laser have been studied theoretically and experimentally. By solving rate equations, the expression for threshold pump power is obtained. The effects of fiber length, mirror reflectivity, pump wavelength, laser wavelength and Yb³⁺ concentration on threshold pump power are discussed. Then, the Yb³⁺-doped double-clad fiber laser with linear cavity is developed. By using various output couplers, threshold pump power has been measured. The experimental results are in accord with theory.     

Passive picosecond and femtosecond mode-locking laser action of Yb<Superscript>3+</Superscript>:LuYSiO<Subscript>5</Subscript>

Efficient passive mode locking of a diode-pumped Yb³⁺:LuYSiO₅ (Yb:LYSO) laser is first demonstrated in experiment using a semiconductor saturable absorber mirror (SESAM), to the best of our knowledge. A stable pulse train with a repetition rate of 101 MHz is generated. The average output power of 2.13 W and the pulse duration of 3.9 ps. With a pair of SF10 uncoated prisms for dispersion compensation, we obtained pulses as short as 780 fs with center wavelength around 1042 nm, the average output power of 1.03 W and the peak power of 13.1 kW.     

Thermal- and Spectral-Characteristics of High-Power Quasi-Continuous Wave 940-nm InGaAs Diode Laser Arrays

Experimental results of the thermal and spectral characteristics of a monolithic stack of high power quasicontinuous wave 940-nm InGaAs linear laser diode arrays have been evaluated. Thermal resistance as the most important thermal parameter characterizing a high-power laser diode package was obtained using the temperature rise measured directly by a thermo-camera. A new simple and convenient technique to measure a spectral transition of the emission from laser diode arrays is proposed. Spectral chirping due to the transient thermal power dissipated during the laser pulse was observed as a time-evolution of the spectral profile; it gave a comprehensible image of the chirping behavior. Comparing the temperature rise in the diode junction with the thermal simulation, it was determined that the thermal shift of central wavelength dλ/dT was 0.21 nm/°C. Detailed performances were identified for pumping a Yb³⁺ doped crystalline laser, and it was verified that the laser diode arrays were satisfactory to meet pumping source requirements for coupling to Yb³⁺ absorption linewidth.     

全光纤超短脉冲掺Yb3+光纤环形激光器

讨论了自启动被动锁模掺Yb³⁺光纤环形激光器产生短脉冲的机理，并研制出全光纤结构超短脉冲掺Yb³⁺光纤环形激光器.采用两个976nm半导体激光器级联抽运作为抽运源，高掺杂浓度掺Yb³⁺光纤作为增益介质，利用光纤的非线性偏振旋转效应，得到自启动、十分稳定的ps量级锁模光脉冲.激光器锁模阈值功率260mW，输出功率25mW，锁模光脉冲中心波长1056nm，3dB带宽11.7nm，重复频率20MHz.与其他结构光纤激光器相比，这种全光纤结构具有更高的效率和更好的稳定性. 关键词： 环形光纤激光器 3+光纤')" href="#">高掺杂浓度掺Yb³⁺光纤 自启动 被动锁模     

Continuous wave laser operation of Yb<Superscript>3+</Superscript>:YVO<Subscript>4</Subscript>

We have demonstrated the continuous wave laser operation of Yb³⁺:YVO₄. For Ti:Al₂O₃ laser pumping at 985 nm, a maximum slope efficiency of 41.1% and a threshold pump power of 76 mW were obtained. The maximum output power was 433 mW at a laser wavelength of 1037 nm.Using a cw diode laser around 974 nm as a pump source, a slope efficiency of 10.9% and a maximum output power of 152 mW were achieved at a laser wavelength of 1039 nm. The laser threshold pump power was 608 mW with respect to the absorbed pump power. The effective emission cross-sections for the ²F_5/2²F_7/2 transition were determined using the Füchtbauer–Ladenburg equation. The maxima of the effective absorption and emission cross-sections were found at 984.5 nm (6.74×10^-20 cm²) in -po larization and 985.5 nm (4.28×10^-20 cm²) also in -p olarization. The upper laser level lifetime was measured with suppression of radiation trapping and is around 318 s. PACS 42.55.Rz; 42.55.Xi; 42.70.Hj     

Diode-pumped passively mode-locked yb<Superscript>3+</Superscript>-doped yttrium lanthanum oxide ceramic sub-picosecond laser

A diode-pumped sub-picosecond laser is realized with Yb³⁺-doped yttrium lanthanum oxide transparent ceramic Yb:(Y_0.9La_0.1)₂O₃ as the gain medium for the first time. By using Gires-Tournois interferometer mirrors and chirped mirror for dispersion compensation and semiconductor saturable absorber mirror for passive mode-locking, laser pulse as short as 730 fs was obtained at the central wavelength of 1033 nm and repetition rate of 65.5 MHz. Under the maximum pump power of 6 W at 976 nm, the output power is 92 mW.