Determination of benzene, toluene, ethylbenzene and xylenes in air by solid phase micro-extraction/gas chromatography/mass spectrometry

The aim of the study was to analyse BTEX compounds (benzene, toluene, ethylbenzene, xylenes) in air by solid phase micro-extraction/gas chromatography/mass spectrometry (SPME/GC/MS), and this article presents the features of the calibration method proposed. Examples of real-world air analysis are given. Standard gaseous mixtures of BTEX in air were generated by dynamic dilution. SPME sampling was carried out under non-equilibrium conditions using a Carboxen/PDMS fibre exposed for 30 min to standard gas mixtures or to ambient air. The behaviour of the analytical response was studied from 0 to 65 g/m³ by adding increasing amounts of BTEX to the air matrix. Detection limits range from 0.05 to 0.1 g/m³ for benzene, depending on the fibre. Inter-fibre relative standard deviations (reproducibility) are larger than 18%, although the repeatability for an individual fibre is better than 10%. Therefore, each fibre should be considered to be a particular sampling device, and characterised individually depending on the required accuracy. Sampling indoor and outdoor air by SPME appears to be a suitable short-delay diagnostic method for volatile organic compounds, taking advantage of short sampling time and simplicity.     

Optimization of in situ derivatization SPME by experimental design for GC-MS multi-residue analysis of pharmaceutical drugs in wastewater

This paper presents the development of a procedure, which enables the analysis of nine pharmaceutical drugs in wastewater using gas chromatography‐mass spectrometry (GC‐MS) associated with solid‐phase microextraction (SPME) for the sample preparation. Experimental design was applied to optimize the in situ derivatization and the SPME extraction conditions. Ethyl chloroformate (ECF) was employed as derivatizing agent and polydimethylsiloxane‐divinylbenzene (PDMS‐DVB) as the SPME fiber coating. A fractional factorial design was used to evaluate the main factors for the in situ derivatization and SPME extraction. Thereafter, a Doehlert matrix design was applied to find out the best experimental conditions. The method presented a linear range from 0.5 to 10 μg/L, and the intraday and interday precision were lower than 16%. Applicability of the method was verified from real influent and effluent samples of a wastewater treatment plant, as well as from samples of an industry wastewater and a river.     

Development of a gas chromatographic/mass spectrometric method to quantify R(-)-apomorphine, R(-)-apocodeine and R(-)-norapomorphine in human plasma and urine

A method was developed and validated for the analysis of R(-)-apomorphine, (R-)-apocodeine and R(-)-norapomorphine in human plasma and urine with N-propylnorapomorphine as internal standard using gas chromatography/mass spectrometry (GC/MS) and single-ion monitoring after a single liquid-liquid extraction and silylation of compounds. The quantification limits were 1 ng/ml for apomorphine and apocodeine and 25 ng/ml for norapomorphine. Calibration curves were linear, within the range 1-100 ng/ml. Variation in intraday and interday precision was below 10%. This method was applied to study apomorphine bioavailability in nine patients with Parkinson's disease before and after coadministration of a catechol-O-methyl transferase inhibitor.     

Application of tandem mass spectrometry combined with gas chromatography to the routine analysis of ethyl carbamate in stone-fruit spirits

Gas chromatography (GC) coupled to mass spectrometry (MS) operated in selected ion monitoring (SIM) mode is currently the method of choice for the determination of the toxic contaminant ethyl carbamate in alcoholic beverages. However, even after extensive sample cleanup over diatomaceous earth columns, the identity of ethyl carbamate often cannot be ascertained with confidence, due to inconsistent ratios of the SIM ions m/z 62, 74 and 44 because the qualifier ions are highly susceptible to interferences. Therefore, a new method combining GC and tandem MS using a triple-quadrupole instrument is introduced to determine ethyl carbamate in stone-fruit spirits. For quantitative analysis the characteristic transitions of m/z 74 --> 44 and m/z 62 --> 44 for ethyl carbamate as well as m/z 64 --> 44 for the deuterated internal standard ethyl carbamate-d5 were monitored in the multiple reaction monitoring (MRM) mode. In the validation studies, ethyl carbamate exhibited good linearity with a regression coefficient of 1.000. The limits of detection and quantitation were 0.01 and 0.04 mg/L. The recovery of the method was 100.4 +/- 9.4%. The precision never exceeded 7.8% (intraday) and 10.1% (interday) and the trueness never exceeded 11.3% (intraday) and 12.2% (interday) at any of the concentrations examined, indicating good assay accuracy. A good agreement of analytical results between a previously developed GC/MS SIM method and the GC/MS/MS MRM procedure was found (R=0.987). Regarding the validation data, the procedure is sensitive, selective and reproducible. The applicability of the developed method was demonstrated by the investigation of 70 stone-fruit spirits from commercial trade. The ethyl carbamate concentration of the samples ranged between 0.07 and 7.70 mg/L (mean 1.21 mg/L). The main advantage of the developed GC/MS/MS method is the reliability of the results without the need for time-consuming confirmatory analyses.     

Determination of benzene at trace levels in air by a novel method based on solid-phase microextraction gas chromatography/mass spectrometry.

A new method for the determination of benzene at trace levels in air is presented. The method consists of the collection of air samples on adsorbent cartridges with simultaneous adsorption of pre-established amounts of D6-labeled internal standard. Desorption from the cartridge is performed by solid-phase microextraction (SPME) with analysis by gas chromatography/mass spectrometry (GC/MS) using an ion trap mass spectrometer. The influence of several parameters (type of SPME fiber, temperature, time, for example) was investigated, and good linearity in the range 10-400 ng of C6D6, with a coefficient of variance (CV) around 3-5%, was obtained. The method was tested by sampling air in a town center in Italy, and a benzene concentration of approximately 50 microg/m(3) was determined. The maximum limit recommended by the European Community is 10 microg/m(3).     

Non-equilibrium solid-phase microextraction coupled directly to ion-trap mass spectrometry for rapid analysis of biological samples

To determine sub-ppb levels of drugs in biological samples, selective, sensitive and rapid analytical techniques are required. This work shows the possibilities for high-throughput analysis of solid-phase microextraction (SPME) directly coupled to an ion-trap mass spectrometer equipped with an atmospheric pressure chemical ionisation source. As no chromatographic separation is performed, the SPME procedure is the time-limiting step. Direct immersion SPME under non-equilibrium conditions permits the determination of lidocaine in urine within 10 min. After a 5 min sorption time with a 100 microm polydimethylsiloxane-coated fibre, the extraction yield of lidocaine from urine is about 7%. When applying 4 min desorption, using a mixture of ammonium acetate buffer (pH 4.5) and acetonitrile (85 + 15 v/v), about 10% of the analyte is retained on the fibre. An extra cleaning step of the fibre is therefore used to prevent carry-over. By use of tandem MS, no matrix interference is observed. The detection limit for lidocaine is about 0.4 ng ml(-1) and the intraday and interday reproducibility are within 14% over a concentration range of 2-45 ng ml(1).     

Performance evaluation of a rapid-scanning quadrupole mass spectrometer in the comprehensive two-dimensional gas chromatography analysis of pesticides in water

The performance of a novel rapid-scanning (20,000 amu/s) quadrupole mass spectrometer (qMS) has been evaluated in the comprehensive 2-D gas chromatography (GC×GC) analysis of pesticides contained in water. Analyte extraction was performed by using direct solid-phase microextraction (SPME). The MS system was operated using a rather wide m/z 50-450 mass range and a 33 Hz spectral production rate, a frequency which was found sufficient for reliable quantification. The qMS performance was evaluated considering: (i) number of data points per peak, (ii) mass spectral quality, (iii) extent of peak skewing, and (iv) consistency of retention times. Seven-point calibration curves (external calibration) were constructed for 28 pesticides over the limit of quantification range of 100 μg/L (1, 5, 10, 25, 50, and 100 μg/L). The solid-phase microextraction-GC×GC-qMS method was validated by calculating limits of detection and quantification, intraday peak area precision, accuracy, and intraday retention-time precision. A series of tap water samples were subjected to analysis, fortunately giving negative results.     

Biomonitoring of benzene and toluene in human blood by headspace-solid-phase microextraction

A simple and rapid method for the determination of benzene and toluene in whole blood by headspace-solid-phase microextraction (HS-SPME) is described. Using SPME fibres coated with 65 μm carboxene/polydimethylsiloxane, limits of quantification (LOQ) of 5 ng/L for benzene and 25 ng/L for toluene are achieved. As a result of its large linear range (i.e. 5–5000 ng/L for benzene) the method is suitable for biomonitoring of both occupationally and environmentally exposed people. The reproducibility of the determination of benzene is ≤ 8%. An interlaboratory comparison demonstrated that the method proposed here compares favorably with existing methods (dynamic headspace, purge and trap).     

Liquid chromatography/negative ion atmospheric pressure photoionization mass spectrometry: a highly sensitive method for the analysis of organic explosives

Gas chromatography/mass spectrometry (GC/MS) is applied to the analysis of volatile and thermally stable compounds, while liquid chromatography/atmospheric pressure chemical ionization mass spectrometry (LC/APCI‐MS) and liquid chromatography/electrospray ionization mass spectrometry (LC/ESI‐MS) are preferred for the analysis of compounds with solution acid‐base chemistry. Because organic explosives are compounds with low polarity and some of them are thermally labile, they have not been very well analyzed by GC/MS, LC/APCI‐MS and LC/ESI‐MS. Herein, we demonstrate liquid chromatography/negative ion atmospheric pressure photoionization mass spectrometry (LC/NI‐APPI‐MS) as a novel and highly sensitive method for their analysis. Using LC/NI‐APPI‐MS, limits of quantification (LOQs) of nitroaromatics and nitramines down to the middle pg range have been achieved in full MS scan mode, which are approximately one order to two orders magnitude lower than those previously reported using GC/MS or LC/APCI‐MS. The calibration dynamic ranges achieved by LC/NI‐APPI‐MS are also wider than those using GC/MS and LC/APCI‐MS. The reproducibility of LC/NI‐APPI‐MS is also very reliable, with the intraday and interday variabilities by coefficient of variation (CV) of 0.2–3.4% and 0.6–1.9% for 2,4,6‐trinitrotoluene (2,4,6‐TNT). Copyright © 2008 John Wiley & Sons, Ltd.     

流动气体捕集法测定贯叶连翘提取物中大孔树脂残留物

采用流动气体捕集法,通过GC／MS法测定贯叶连翘提取物中大孔树脂残留物—苯、甲苯和二乙烯苯。与萃取、回流和顶空进样三种处理方式比较,自制的流动气体捕集装置能够很好地收集待测成分并有效地消除干扰。整体(流动气体捕集法处理 含量测定)检出限和回收率(苯：0．3ng/g,99．0％;甲苯：0．8ng／g,99．5％;二乙烯苯：0．5ng／g,99．2％),与GC／MS法所得结果(苯：0．1ng／g,99．2％;甲苯：0．2ng／g,99．4％;二乙烯苯：0．1ng／g,99．2％)无显著差别,说明该法有较低的检出限和良好的回收率。经其他3种方式处理后,检出限变差回收率下降。结果证明流动气体捕集法适于中药提取物中大孔树脂残留物的定量检测。     

Preparation and application of carbon nanotubes/poly(o‐toluidine) composite fibers for the headspace solid‐phase microextraction of benzene,toluene, ethylbenzene,and xylenes

A novel nanocomposite coating of poly(o‐toluidine) and oxidized multiwalled CNTs (MWCNTs, where CNTs is carbon nanotubes) was electrochemically prepared on a stainless‐steel wire. The applicability of the fiber was assessed for the headspace solid‐phase microextraction of benzene, toluene, ethylbenzene, and xylenes in aqueous samples followed by GC with flame ionization detection. In order to obtain an adherent and stable composite coating, several experimental parameters related to the coating process, such as polymerization potential and time, and the concentration of o‐toluidine and oxidized MWCNTs were optimized. The combination of MWCNTs and polymer in a nanocomposite form presents desirable opportunities to produce materials for new applications. The effects of various parameters on the efficiency of the headspace solid‐phase microextraction process, such as desorption temperature and time, extraction temperature and time, and ionic strength were also investigated. At the optimum conditions, LODs were 0.03–0.06 μg/L. The method showed linearity in the range of 0.5–300 μg/L with coefficients of determination >0.99. The intraday and interday RSDs obtained at a 5 μg/L concentration level (n = 5) using a single fiber were 1.2–5.2 and 3.2–7.5%, respectively. The fiber‐to‐fiber RSD (%; n = 3) at 5 μg/L was 6.1–9.2%.     

Disposable ionic liquid coating for headspace solid-phase microextraction of benzene, toluene, ethylbenzene, and xylenes in paints followed by gas chromatography-flame ionization detection

Solid-phase microextraction (SPME) with a disposable ionic liquid (IL) coating was developed for headspace extraction of benzene, toluene, ethylbenzene, and xylenes (BTEX) in paints. The SPME fiber was coated with IL prior to every extraction, then the analytes were extracted and desorbed on the injection port of gas chromatography, and finally the IL coating on the fiber was washed out with solvents. The coating and washing out of IL from the fiber can be finished in a few minutes. This disposable IL-coated fiber was applied to determine BTEX in water-soluble paints with results in good agreement with that obtained by using commercially available SPME fibers. For all the four studied paints samples, the benzene contents were under the detection limits, but relatively high contents of toluene, ethylbenzene and xylenes (56-271 microg g(-1)) were detected with spiked recoveries in the range of 70-114%. Compared to the widely used commercially available SPME fibers, this proposed disposable IL-coated fiber has much lower cost per determination, comparable reproducibility (RSD < 11%), and no carryover between each determination. Considering that IL possess good extractability for various organic compounds and metals ions, and that task-specific IL can be designed and synthesized for selective extraction of target analytes, this disposable IL coating SPME might has great potential in sample preparation.     

Biomonitoring of benzene and toluene in human blood by headspace-solid-phase microextraction

A simple and rapid method for the determination of benzene and toluene in whole blood by headspace-solid-phase microextraction (HS-SPME) is described. Using SPME fibres coated with 65 μm carboxene/polydimethylsiloxane, limits of quantification (LOQ) of 5 ng/L for benzene and 25 ng/L for toluene are achieved. As a result of its large linear range (i.e. 5–5000 ng/L for benzene) the method is suitable for biomonitoring of both occupationally and environmentally exposed people. The reproducibility of the determination of benzene is ≤ 8%. An interlaboratory comparison demonstrated that the method proposed here compares favorably with existing methods (dynamic headspace, purge and trap). Received: 9 February 1998 / Revised: 6 July 1998 / Accepted: 18 July 1998     

Development of a liquid chromatography/tandem mass spectrometry assay for the quantification of PM02734, a novel antineoplastic agent, in dog plasma

A rapid and sensitive liquid chromatography/tandem mass spectrometry (LC/MS/MS) assay was developed and validated to quantify a novel antineoplastic agent, PM02734, in dog plasma. The method was validated to demonstrate the specificity, limit of quantification (LOQ), accuracy, and precision of measurements. The calibration range for PM02734 was established using PM02734 standards from 0.05 to 100 ng/mL in blank plasma. The dominating ions were doubly charged molecular ions [M+2H]2+ at m/z 740.0 instead of singly charged ones at m/z 1478.4. The selected reaction monitoring (SRM), based on the m/z 740.0 --> 212.2 transition, was specific for PM02734, and that based on the m/z 743.8 --> 212.2 transition was specific for deuterated PM02734 (the internal standard, IS); no endogenous materials interfered with the analysis of PM02734 and IS from blank plasma. The assay was linear over the concentration range 0.05-100 ng/mL. In terms of sensitivity of assay 0.05 ng/mL is a very low LLOQ, especially considering PM02734 is a peptide. The correlation coefficients for the calibration curves ranged from 0.9990 to 0.9999. The mean intraday and interday accuracies for all calibration standards (n = 9) ranged from 93 to 111% (< or =11% bias) in dog plasma, and the mean interday precision for all calibration standards was less than 6.4%. The mean intra- and interday assay accuracy for all quality control replicates in dog plasma (n = 9), determined at each QC level throughout the validated runs, ranged from 85-111% (< or =15% bias) and from 99-109% (< or =9% bias), respectively. The mean intra- and interday assay precision was less than 12.1 and 13.3% for all QC levels, respectively. The assay has been used to support preclinical pharmacokinetic (PK) and toxicokinetic studies. The results showed that preclinical samples could be monitored for PM02734 up to 168 h after dosing, which allowed us to identify multiple elimination phases and accurately estimate PK information.     

Implementing tandem mass spectrometry as a routine tool for characterizing the complete purine and pyrimidine metabolic profile in urine samples

Purines and pyrimidines are the basic constituents of DNA and RNA and constitute the basis of at least 50 other important compounds that serve equally vital but separate roles as integral components of intracellular mononucleotide pools. They maintain the supply of these basic components to the different nucleotide pools through an extremely efficient mechanism involving the degradation and recycling of the daily waste products of normal cell turnover. We have developed an LC-MS/MS diagnostic and routine monitoring method for known defects due to both purine and pyrimidine metabolism in a single analysis. Precision tests were made by spiking several urine samples with different creatinine concentrations. For nonspiked low-creatinine urine, intraday precision was in the range of 0.1-9.8% and interday precision was between 1.6 and 14.1%. For nonspiked high-creatinine urine, intraday precision was in the range 0.5-17.2% and interday precision was between 1.5 and 29%. Limit-of-detection (LOD) was in the range 0.1-10 micromol/l and limit-of-quantification (LOQ) in the range of 0.2-15 micromol/l. The current 'dilute and shoot' approach monitors many metabolites, and utilizes a reverse phase chromatographic analysis with a detection requiring 17 min of analysis time. Tandem mass spectrometry and isotope dilution technique enable the accurate quantitation of more than 30 metabolites in one analysis.     

Determination of 3-hydroxy pterocarpan, a novel osteogenic compound in rat plasma by liquid chromatography-tandem mass spectrometry: application to pharmacokinetics study

A rapid, sensitive and selective LC‐MS/MS method for the quantitative analysis of 3‐hydroxy pterocarpan (S006‐1709) in female rat plasma has been developed and validated. A Discovery RP₁₈ column was used for the chromatographic elution using acetonitrile and 0.1% acetic acid in water as mobile phase (80:20 v/v) at the flow rate of 0.5 mL/min. MS/MS analysis was performed using a triple quadrupole mass spectrometer with electrospray ionization in negative ion mode using biochanin as an internal standard (IS). Extraction of S006‐1709 and IS from rat plasma was done by liquid–liquid extraction method using diethyl ether. The LC‐MS/MS method was sensitive with 1.95 ng/mL as the limit of detection and 3.9 ng/mL as the lower limit of quantification. The method was linear in the concentration range of 3.9–1000 ng/mL. The percentage bias for intraday and interday accuracy was not greater than 4.2 and the %RSD for intraday and interday precision was not greater than 13.2. The recoveries of S006‐1709 and IS were 73.9–79.3 and 85.7%, respectively. S006‐1709 was found to be stable in various stability studies. The validated LC‐MS/MS method was successfully applied for the oral pharmacokinetics study of S006‐1709 at 10 mg/kg in female Sprague–Dawley rats. Copyright © 2010 John Wiley & Sons, Ltd.     

A simple gas chromatography method for the analysis of monoethanolamine in air

A simple method determining airborne monoethanolamine has been developed. Monoethanolamine determination has traditionally been difficult due to analytical separation problems. Even in recent sophisticated methods, this difficulty remains as the major issue often resulting in time-consuming sample preparations. Impregnated glass fiber filters were used for sampling. Desorption of monoethanolamine was followed by capillary GC analysis and nitrogen phosphorous selective detection. Separation was achieved using a specific column for monoethanolamines (35% diphenyl and 65% dimethyl polysiloxane). The internal standard was quinoline. Derivatization steps were not needed. The calibration range was 0.5-80 μg/mL with a good correlation (R(2) = 0.996). Averaged overall precisions and accuracies were 4.8% and -7.8% for intraday (n = 30), and 10.5% and -5.9% for interday (n = 72). Mean recovery from spiked filters was 92.8% for the intraday variation, and 94.1% for the interday variation. Monoethanolamine on stored spiked filters was stable for at least 4 weeks at 5°C. This newly developed method was used among professional cleaners and air concentrations (n = 4) were 0.42 and 0.17 mg/m(3) for personal and 0.23 and 0.43 mg/m(3) for stationary measurements. The monoethanolamine air concentration method described here was simple, sensitive, and convenient both in terms of sampling and analytical analysis.     

High-performance liquid chromatography/tandem mass spectrometry method for the determination of arbidol in human plasma

An HPLC/MS/MS method for the determination of arbidol in human plasma was developed. Arbidol and internal standard (loratadine) were extracted from alkaline plasma with tert-butyl methyl ether and analyzed on a Zorbax SB C18 column (30 x 2.1 mm id, 3.5 microm particle size). The detection was by monitoring arbidol at m/z 479.1 --> 434.1 and the internal standard at m/z 383.2 --> 337.2. The method was validated according to U.S. Food and Drug Administration guidelines. The calibration curve was linear over the range of 0.5-500 ng/mL using a 100 microL sample volume. The intraday and interday precisions were less than 6.5%, and acceptable values were obtained for accuracy, recovery, and sensitivity. The developed method was selective, simple, sensitive, and easily applicable.     

Automated analysis of lidocaine and its metabolite in plasma by in-tube solid-phase microextraction coupled with LC-UV for pharmacokinetic study

A sensitive, selective, and reproducible in-tube solid-phase microextraction and liquid chromatographic (in-tube SPME/LC-UV) method for determination of lidocaine and its metabolite monoethylglycinexylidide (MEGX) in human plasma has been developed, validated, and further applied to pharmacokinetic study in pregnant women with gestational diabetes mellitus (GDM) subjected to epidural anesthesia. Important factors in the optimization of in-tube SPME performance are discussed, including the draw/eject sample volume, draw/eject cycle number, draw/eject flow rate, sample pH, and influence of plasma proteins. The limits of quantification of the in-tube SPME/LC method were 50 ng/mL for both metabolite and lidocaine. The interday and intraday precision had coefficients of variation lower than 8%, and accuracy ranged from 95 to 117%. The response of the in-tube SPME/LC method for analytes was linear over a dynamic range from 50 to 5000 ng/mL, with correlation coefficients higher than 0.9976. The developed in-tube SPME/LC method was successfully used to analyze lidocaine and its metabolite in plasma samples from pregnant women with GDM subjected to epidural anesthesia for pharmacokinetic study.     

The comparison of solid phase microextraction-GC and static headspace-GC for determination of solvent residues in vegetable oils

The objective of these investigations has been the determination of volatile organic compounds including residue solvents present in vegetable oil samples. Some olive oil, rape oil, sunflower oil, soy-bean oil, pumpkin oil, grape oil, rice oil as well as hazel-nut oil samples were analysed. Among residue solvents the following compounds have been mentioned: acetone, n-hexane, benzene, and toluene. Some experiments for the solid phase microextraction (SPME)-GC-flame ionisation detection (FID) were performed to examine extraction conditions such as fiber exposure time, temperature of extraction, and temperature of desorption. Various SPME fibers such as polydimethylsiloxane, Carboxen/polydimethylsiloxane and polydimethylsiloxane/divinylbenzene coatings were used for the isolation of tested compounds from vegetable oil samples. After optimisation of SPME, real vegetable oil samples were examined using SPME-GC/MS. Based on preliminary experiments the qualitative and quantitative analyses for the determination of acetone, n-hexane, benzene and toluene were performed by SPME-GC-FID and static head-space (SHS)-GC-FID methods. The regression coefficients for calibration curves for the examined compounds were R(2) > or = 0.992. This shows that the used method is linear in the examined concentration range (0.005-0.119 mg/kg for SPME-GC-FID and 0.003-0.728 mg/kg for SHS-GC-FID). Chemical properties of analysed vegetable oils have been characterised by chemometric procedure (cluster analysis).