Preparation approaches of the coated capillaries with liposomes in capillary electrophoresis

The use of liposomes as coating materials in capillary electrophoresis has recently emerged as an important and popular research area. There are three preparation methods that are commonly used for coating capillaries with liposomes, namely physical adsorption, avidin–biotin binding and covalent coupling. Herein, the three different coating methods were compared, and the liposome-coated capillaries prepared by these methods were evaluated by studying systematically their EOF characterization and performance (repeatability, reproducibility and lifetime). The amount of immobilized phospholipids and the interactions between liposome or phospholipid membrane and neutral compounds for the liposome-coated capillaries prepared by these methods were also investigated in detail. Finally, the merits and disadvantages for each coating method were reviewed.     

A covalent capillary coating of diazoresin and polyglycerol dendrimer for protein analysis using capillary electrophoresis

Overcoming proteins adsorption on the inner surface of capillary has attracted increasing attention recently. By using the unique photochemistry reaction of diazoresin (DR), a new covalent capillary coating was prepared on the fused‐silica capillary through layer‐by‐layer self‐assembly of DR with polyglycerol (PG) dendrimer. The separation performance of covalently DR/PG‐dendrimer coated capillary noticeably exceeded the bare capillary and the noncovalently linked DR/PG‐dendrimer capillary. A baseline separation of lysozyme, myoglobin, bovine serum albumin, and ribonuclease A was achieved using CE within 20 min. Besides, the covalently linked DR/PG‐dendrimer coating has the remarkable stability and reproducibility. Especially, compared with the traditional method which use highly toxic and moisture‐sensitive silane coupling agent, this method seems to be a simple and environmental friendly way to prepare the covalently coated capillaries for CE.     

甲氧苄啶的毛细管电泳快速检测新方法

建立了毛细管电泳高频电导法测定药物和尿液中的甲氧苄啶。考察了各种条件对分离和检测的影响。以4.0 mmol/L HAc 体积分数10%甲醇(pH4.0)为电泳介质,分离电压20.0 kV,重力虹吸进样。在优化条件下,甲氧苄啶峰形良好,出峰时间小于6 min,线性范围为1.5~120.0μg/mL,检出限0.5μg/mL。该方法样品处理过程简单,可用于药物制剂的质量控制和临床检验。     

Polypyrrole-coated capillaries for capillary zone electrophoresis

Fused-silica capillaries are permanently coated by silanization with 3-{[3-(N-pyrrole)-2-hydroxypropyl]amino}propyltriethoxysilane followed by oxidative polymerization of the pyrrole moieties with iron (III) or peroxodisulfate in the presence of chloride, perchlorate, or dextransulfate as anions. This approach allows to modulate the EOF in its magnitude as well as in its direction. With the small anions chloride and perchlorate, the EOF is reversed below pH 5 while with the large dextransulfate polyanions (DS) the EOF is relatively constant over the pH range from 2.5 to 9.4. This can be of advantage at low pH, at which the EOF of uncoated capillaries is close to zero. Application for separation of some herbicides is shown. The lifetime of PP-modified capillaries is satisfactory: the decrease in EOF is less than 3% during 80 analyses (160 min) and less than 5% over three months of storage. The reproducibility of capillary modification is about 5% (RSD of EOF).     

A covalent modified hydrophilic capillary for enhanced capillary electrophoresis of biopolymers

δ-Gluconolactone was covalently coupled to aminopropyl derivatized capillary,which created hydrophilic brushes on the inner wall of the capillary.The coated capillary was shown to generate a stable electroosmotic flow(EOF) in the investigated pH range of 2.0-9.0 and to suppress effectively the adsorption of proteins.And it enabled separation of some biopolymer mixtures including basic proteins,DNA and tryptic digested bovine serum albumin(BSA) within 15 min with efficiencies up to 450,000 plates/m.The in...     

A novel diazoresin/poly(N‐vinyl aminobutyric acid) covalent capillary coating for the analysis of proteins by capillary electrophoresis

A novel method for the preparation of covalently linked capillary coatings of poly(N‐vinyl aminobutyric acid) (PVAA) obtained from hydrolyzed polyvinylpyrrolidone was demonstrated using photosensitive diazoresin (DR) as a coupling agent. A layer‐by‐layer self‐assembled film of DR and PVAA based on ionic bonding was first fabricated on the inner wall of capillary, then ionic bonding was converted into covalent bonding after treatment with UV light through a unique photochemical reaction of DR. The covalently bonded coatings suppressed protein adsorption on the inner surface of the capillary, and thus a baseline separation of lysozyme, cytochrome c, BSA, amyloglucosidase, and myoglobin was achieved using CE. Compared with bare capillary or noncovalently bonded DR/PVAA coatings, the covalently linked DR/PVAA capillary coatings not only improved the CE separation performance for proteins, but also exhibited good stability and repeatability. Due to the replacement of the highly toxic and moisture‐sensitive silane coupling agent by DR in the covalent coating preparation, this method may provide a green and easy way to make covalently coated capillaries for CE.     

Piperazine-based buffers for liposome coating of capillaries for electrophoresis

Anionic liposomes can be coated on fused-silica capillaries for electrophoresis in the presence of N-(hydroxyethyl)piperazine-N'-(2-ethanesulfonic acid) (HEPES) as background electrolyte (BGE) solution. In this work, the interaction of various compounds with zwitterionic and anionic phospholipid coatings was studied with HEPES at pH 7.4 as BGE solution. The chromatographic and electrophoretic behavior of three test sample solutions (anionic, cationic, and neutral) was investigated for evaluation of the phospholipid coatings. Our results show that hydrophobic interactions between analytes and the phospholipid coating are important for the migration of charged analytes. In addition, the performances of other piperazine-based buffers, i.e., N-(2-hydroxyethyl)piperazine-N'-(2-hydroxypropanesulfonic acid), piperazine-N,N'-bis(2-ethanesulfonic acid), and piperazine-N,N'-bis(hydroxypropane sulfonic acid), at pH 7.4, as liposome solvent and BGE solution were evaluated and compared with the performance of HEPES at pH 7.4. The anionic liposome solution comprised 80/20 mol% phosphatidylcholine/phosphatidylserine. A simple test solution was selected and the chromatographic and electrophoretic migration behavior of the analytes was evaluated. The results show that, in addition to HEPES, other piperazine-based buffers at pH 7.4 are suitable for coating of fused-silica capillaries with anionic liposomes.     

A novel injection method for high-speed proteome analysis by capillary electrophoresis

We have developed a new sample injection method for capillary electrophoresis (CE) that reduces the required migration time. We demonstrated a pressurization technique that was performed with buffer in the outlet after the electrokinetic sample injection with no buffer in the outlet. To reduce the migration time, the sample injection had to be performed with no buffer in the outlet; water should be pressurized while the buffer is in the outlet. Though the resolution was slightly decreased using this method, the addition of a separation carrier (curdlan) to the run buffer restored the resolution without delaying the migration time. The use of our new sample injection method combined with our high-quality separation carrier will enable us to improve the efficiency of the high-throughput screening (HTS) system for proteome analysis.     

A novel sealing method in static coating fused-silica capillary column

Summary In this paper a new sealing method for the static coating of capillary columns is described. When one end of the fully filled capillary was immersed into liquid nitrogen in a Dewar flask, the coating solution at this end would be frozen and became a temporary seal, and an air-free solvent/seal interface was obtained. No bumping has ever been found at the interface, even when butane was used as solvent. By applying this sealing method, several capillary columns, including some narrow bore capillary, had been successfully coated.     

Novel polyamine coating providing non-covalent deactivation and reversed electroosmotic flow of fused-silica capillaries for capillary electrophoresis

A new polycationic coating for use in capillary electrophoresis has been developed that enables chemical modification of fused-silica capillary surfaces for analysis of compounds like basic proteins. The cationic polyamine, containing short aliphatic blocks of combined 2 and 3-carbon length, was physically adsorbed onto the negatively charged fused-silica surface through ionic interaction by flushing the capillary with a polyamine solution, followed by a self-stabilization step. The polyamine coated capillaries generated an anodal electroosmotic flow that was independent of pH in the investigated range of pH 4-8. The capillary performance was demonstrated by fast separations of basic proteins with peak efficiencies in the range of 265,000-584,000 plates.     

Variation of zeta-potential with temperature in fused-silica capillaries used for capillary electrophoresis

The temperature variation of electroosmotic mobility corrected for the effects of Joule heating (muEOF0) was employed to investigate the variation of the zeta-potential (zeta) with temperature in fused-silica capillaries. Experimentally determined values for zeta increased at 0.39% per degrees C, a rate that is about four to five times smaller than reported previously. Experimentally determined values of zeta were directly proportional to the absolute temperature although values were also influenced slightly by changes to the dielectric constant. It was found that the effective charge density at the inner surface of the capillary was independent of temperature.     

Preparation and characterization of calixarene-coated capillaries for capillary electrophoresis

Preparation and characterization of calixarene-coated capillaries for capillary electrophoresis (CE) were exemplified with p-allylcalix[4]arene (pACX4) which was immobilized to the fused silica surface using gamma-methacryloxypropyl-trimethoxysilane (gamma-MAPS) as linking agent. Successful gamma-ACX4 coating was suggested by the greatly decreased electroosmotic flow (EOF), due to the introduction of phenolic hydroxyl groups on the inner surface of the capillaries. A slight slope of EOF versus pH at pH <8 would help make the separation reproducible. The coated columns also featured a low ultraviolet (UV) absorption background and long lifetime (> 6 months at 4相似文献   

A fully automated linear polyacrylamide coating and regeneration method for capillary electrophoresis of proteins

Surface modification of the inner capillary wall in CE of proteins is frequently required to alter EOF and to prevent protein adsorption. Manual protocols for such coating techniques are cumbersome. In this paper, an automated covalent linear polyacrylamide coating and regeneration process is described to support long‐term stability of fused‐silica capillaries for protein analysis. The stability of the resulting capillary coatings was evaluated by a large number of separations using a three‐protein test mixture in pH 6 and 3 buffer systems. The results were compared to that obtained with the use of bare fused‐silica capillaries. If necessary, the fully automated capillary coating process was easily applied to regenerate the capillary to extend its useful life‐time.     

A novel capillary electrophoresis method for the determination of d-serine in neural samples

A capillary electrophoresis method has been developed for the determination of d-serine in neural samples. d/l-serine was tagged with naphthalene-2,3-dicarboxaldehyde (CBI-d/l-Ser), and the separation of CBI-d/l-Ser enantiomer was achieved by using a dual chiral selector system consisting of β-cyclodextrin (β-CD) and chiral micelles formed by sodium deoxycholate (SDC). No resolution was observed when either β-CD or SDC was used alone. Moreover, the combined use of β-CD with achiral micelles of sodium dodecylsulfate (SDS) exhibited no resolving effect. With laser induced fluorescence detection, the limit of detection was 3.0 × 10⁻⁸ M Ser. Under the separation conditions selected, no other amino acids co-eluted with l-/d-Ser enantiomers. Using the present method, d-Ser level in Aplysia ganglia homogenates was found to vary significantly from animal to animal. Interestingly, d-Ser was not detected in single neurons isolated from Aplysia ganglia.     

Phospholipid-lysozyme coating for chiral separation in capillary electrophoresis

A phospholipid coating with lysozyme as chiral recognition reagent permeated into the phospholipid membrane was developed for the chiral capillary electrophoretic (CE) separation of D- and L-tryptophan. As a kind of carriers, coated as phospholipid membranes onto the inner wall of a fused-silica capillary, liposomes are able to interact with basic proteins such as lysozyme, which may reside on the surface of the phospholipid membrane or permeate into the middle of the membrane. The interaction results in strong immobilization of lysozyme in the capillary. Coatings prepared with liposomes alone did not allow stable immobilization of lysozyme into the phospholipid membranes, as seen from the poor repeatability of the chiral separation. When 1-(4-iodobutyl)-1,4-dimethylpiperazin-1-ium iodide (M1C4) was applied as a first coating layer in the capillary, the electroosmotic flow (EOF) was effectively suppressed, the phospholipid coating was stabilized, and the lysozyme immobilization was much improved. The liposome composition, the running buffer, and the capillary inner diameter all affected the chiral separation of D- and L-tryptophan. Coating with 4 mM M1C4 and then 1 mM phosphatidylcholine (PC)/phosphatidylserine (PS) (80:20 mol%), with 20 mM (ionic strength) Tris at pH 7.4 as the running buffer, resulted in optimal chiral separation with good separation efficiency and resolution. Since lysozyme was strongly permeated into the membrane of the phospholipids on the capillary surface, the chiral separation of D- and L-tryptophan was achieved without lysozyme in the running buffer. The effects of different coating procedures and separation conditions on separation were evaluated, and the M1C4-liposome and liposome-lysozyme interactions were elucidated. The usefulness of protein immobilized into phospholipid membranes as a chiral selector in CE is demonstrated for the first time.     

Wall coating for capillary electrophoresis on microchips

This review article with 116 references describes recent developments in the preparation of wall coatings for capillary electrophoresis (CE) on a microchip. It deals with both dynamic and permanent coatings and concentrates on the most frequently used microchip materials including glass, poly(methyl methacrylate), poly(dimethyl siloxane), polycarbonate, and poly(ethylene terephthalate glycol). Characterization of the channel surface by measuring electroosmotic mobility and water contact angle of the surface is included as well. The utility of the microchips with coated channels is demonstrated by examples of CE separations on these chips.     

Cycloaliphatic epoxy resin coating for capillary electrophoresis

Coating the interior surface of a fused-silica capillary with a polymeric material has long been used in capillary electrophoresis (CE) to reduce or eliminate electroosmotic flow and suppress adsorption. A cycloaliphatic epoxide-based resin was bonded to silane treated capillaries and crosslinked with a curing agent. The epoxy resin coating significantly reduced electroosmotic flow over a pH range of 3-10. This coating was sufficiently hydrophilic to suppress protein adsorption. The epoxy resin coated capillary was used to separate several acidic and basic proteins and peptides. Separation efficiencies greater than 400,000 theoretical plates were achieved. The relative standard deviations in migration times for proteins were <0.8%. Speed and simplicity are important advantages of the coating procedure compared to other published coating methods.     

Characterization of a sapphire-epoxy coating for capillary electrophoresis

A new procedure for coating capillaries for capillary electrophoresis applying a sapphire (alumina) containing epoxy resin was developed. Coated capillaries showed considerably reduced electroosmotic flow, and decreased the adsorption of proteins to the internal wall of the capillary. Coating is transparent down to 195 nm and can be used with advantage to analyze different kinds of substances, such as small cations and/or anions, and proteins.     

Alcohols and wide-bore capillaries in nonaqueous capillary electrophoresis.

The feasibility of using C1-C5 alcohols as electrolyte solutions in nonaqueous capillary zone electrophoresis was investigated. The separation of basic narcotic analgesics and acidic diuretics was modified by changing the alcohol in an electrolyte solution containing alcohol-acetonitrile-acetic acid (50:49:1, v/v) and 20 mM ammonium acetate while other experimental conditions were kept constant. The alcohols studied were methanol, ethanol, 1-propanol, 2-propanol, 1-butanol, 2-butanol, and 1-pentanol. The results indicate that even longer-chain alcohols can be used in nonaqueous capillary zone electrophoresis and, because of the lower currents they allow, they are especially advantageous in wider capillaries. Basic analytes were separated in 200 microm and 320 microm ID capillaries with 1-butanol-acetonitrile-acetic acid (50:49:1, v/v) containing 20 mM ammonium acetate as electrolyte solution. Problems related to the use of wide-bore capillaries are discussed.