聚酰胺表面结构及其对复合膜分离性能的影响

以杂萘联苯聚芳醚超滤膜为支撑层,通过间苯二胺(MPD)、哌嗪(PIP)与均苯三甲酰氯(TMC)的界面聚合制备复合膜.用红外光谱和X射线衍射分别分析了超薄功能层的化学结构与聚集态,用原子力显微镜观察了膜表面形貌,并用统计学方法计算了膜表面的平均粗糙度等特性参数,研究了MPD/PIP比例对膜表层化学结构、形貌和分离性能的影响.结果表明,随着二胺单体MPD/PIP比例从0/100提高到100/0,功能层聚酰胺的聚集态具有从无定形向部分结晶转变的趋势,复合膜表面平均粗糙度由17.8nm提高到71.9nm,膜对NaCl的截留率由26%提高到99%,而通量则由130L.m-2.h-1降低到12L.m-2.h-1.复合膜具有良好的稳定性,温度由25℃提高到80℃,通量提高了2倍左右,而对NaCl的截留率基本不变.     

二胺结构对聚酰胺复合纳滤膜性能的影响

分别以邻苯二胺、间苯二胺、对苯二胺为水相单体,均苯三甲酰氯(TMC)为油相单体,聚醚砜超滤膜为基膜,界面聚合法制备了复合纳滤膜.在纳滤膜对Na<,2>SO<,4>,MgSO<,4>,MgCl<,2>和NaCl四种盐的脱盐率中,间苯二胺膜最高,对苯二胺膜居中,邻苯二胺膜最差;在纳滤膜耐氯性能方面,对苯二胺最佳,邻苯二胺居...     

Armos/聚砜共混中空纤维基膜及其纳滤复合膜的制备与性能研究

中空纤维膜因其体积装填密度高、占地面积小、成本相对低等优点备受关注。本文通过将Armos聚合液与聚砜(PSf)共混，经干-湿法纺丝制备了Armos/PSf共混中空纤维超滤膜，研究表明：Armos均匀分散在中空纤维膜中，中空纤维膜断面呈现疏松的多孔结构，随着Armos共混含量的增加，膜的亲水性和纯水通量均提高，但对PEG-20000截留率下降明显。以Armos/PSf共混中空纤维膜为基膜，通过界面聚合制备了中空纤维复合纳滤膜，优化的制备条件为：基膜中Armos的共混含量为4%、水相单体浓度为3%、油相单体浓度为0.15%时，制得的中空纤维复合纳滤膜性能最佳，其通量为8.40L/(m²·h)，对MgSO₄的截留率为88%。     

界面聚合制备新型荷正电纳滤膜

以聚砜超滤膜为基膜,聚乙烯亚胺、均苯三甲酰氯为界面聚合单体,水和正己烷分别为两相溶剂,通过界面聚合方法制备荷正电纳滤膜。实验着重考察了Na2SO4-PEG400-H2O三元混合体系的分离情况,结果表明,该膜可有效地实现低分子量有机物与Na2SO4的分离;另外,随着Na2SO4或PEG400浓度的增大,膜对Na2SO4和PEG400的截留率有所降低。     

季铵盐高分子抗菌剂的工艺优化与抗菌性能研究

采用正交实验设计,进行公斤级批量制备DMAEMA-DB季铵盐单体和抗菌聚合物的研究,对影响单体合成的关键因素以及聚合的条件进行优化,并采用FT-IR和NMR等方法对所合成的单体和聚合物分别进行了结构表征,通过平板活菌计数法测定了单体以及聚合物的抗菌性能.结果表明,DMAEMA-DB单体的优化合成条件为:反应温度55℃,反应时间30h,反应物浓度为V<,s>:V<,l>=1:1,反应物配比为DMAEMA:DB=1:1.1.Poly(AAm/DMAEMA-DB)的最佳合成工艺条件为:聚合温度70℃,聚合时间8h,单体浓度为0.4mol/L,引发剂用量为单体用量的0.4mol%,在该条件下合成的聚合物平均得率达89%.将它们用于杀灭大肠杆菌时,接触时间5min对大肠杆菌的抑菌率可达99%,接触时间30min抑菌率达到100%.     

聚4-乙烯基吡啶原位修饰PVDF膜及其负载磷钨杂多酸催化剂的研究

以聚偏氟乙烯(polyvinylidene fluoride,PVDF)微滤膜为基膜,4-乙烯基吡啶(4-vinylpyridine,4VP)为功能单体,采用表面引发电子活化再生原子转移自由基聚合(SI-AGET ATRP)法在基膜表面原位改性,并通过接枝聚合物侧链上的吡啶基团与Keggin型磷钨杂多酸(H3PW12O40·n H2O,HPW)之间的静电作用,制备了新型混合催化膜.实验结果表明,接枝聚合过程表现出"活性"/可控表面引发接枝聚合性质,基膜表面接枝聚合物量随聚合反应时间呈现线性增加,当反应时间为16 h,聚合物接枝量达到2.25 mg/cm2,聚合物接枝量的增多致使其相互堆积并坍塌,造成膜表面出现块状聚集体.然后,利用溴代十六烷对接枝聚合物进行季铵化改性,制得表面含有吡啶鎓盐的阳离子复合膜,通过接枝聚合物侧基中的吡啶和吡啶鎓盐基团与磷钨杂多酸之间的静电作用促使其在改性膜表面上有效负载.负载后的磷钨杂多酸均匀的分布在膜表面及孔道中,并保持其化学结构.负载催化剂前后膜的接触角从80.4°减小到57.8°,体现了亲水性催化剂的负载对膜表面润湿性的显著影响.     

含氟聚丙烯酸酯乳液的合成、表征及其应用

以高交联性能的丙烯酸-4-羟基丁酯(4HBA)、丙烯酸丁酯(BA)、甲基丙烯酸十二氟庚酯(G04)等为聚合单体,通过延迟滴加氟单体的核壳乳液聚合工艺,合成了表面富含氟元素的含氟聚丙烯酸酯。采用红外光谱仪、热重分析仪、差示扫描量热仪、原子力显微镜、X光电子能谱仪及接触角测定仪表征了其性能与结构。分析结果表明:当G04质量为聚合单体总质量的20%时,聚合物干膜对水、油的接触角分别为94°和81°,表面能为31 J/m~2,交联单体4HBA的最佳用量为w(4HBA)=4%,该乳液在成膜过程中,氟元素优先向膜表面富集。     

采用巯基-BPO氧化还原引发体系实现GMA在硅胶微粒表面的高效接枝聚合

使用偶联剂γ-巯丙基三甲氧基硅烷(MPMS,KH-590),对微米级硅胶微粒进行了表面化学改性,制得了表面带有巯基的改性微粒MPMS-SiO2.使改性微粒MPMS-SiO2表面的巯基与溶液中的BPO构成氧化-还原引发体系,实现了油溶性单体甲基丙烯酸缩水甘油酯(GMA)在硅胶微粒表面的引发接枝聚合,制得了接枝度为26g/100g的接枝微粒PGMA/SiO2.采用红外光谱(FTIR)、扫描电镜(SEM)及热重分析(TGA)等方法对接枝微粒PGMA/SiO2进行了表征。在此基础上,重点研究了主要因素对巯基-BPO体系引发GMA接枝聚合的影响.研究结果表明,巯基-BPO体系引发的接枝聚合,由于活性位点位于固体表面,因此也是一种表面引发接枝法。与在固体微粒表面引入可聚合双键的"穿过接枝"("grafting through")法相比,巯基-BPO引发体系可更有效地实现油溶性单体的接枝聚合.为制得高接枝度的接枝微粒PGMA/SiO2,适宜的温度为55℃,适宜的BPO用量为单体的1wt%左右,适宜的单体浓度为10 wt%。     

新型聚(酰胺-脲-酰亚胺)反渗透复合膜的稳定性

通过二次界面聚合法制备了一种新型的聚(酰胺-脲-酰亚胺)反渗透复合膜.将常规二元胺——间苯二胺(MPD)与关键功能单体5-异氰酸酯基-异肽酰氯(ICIC)通过界面聚合得到MPD-ICIC初生态基膜,再与关键功能单体N,N'-二甲基间苯二胺(DMMPD)经二次界面聚合制得聚(酰胺-脲-酰亚胺)反渗透复合膜.采用傅里叶变换红外光谱和X射线光电子能谱分析膜活性层的化学结构,评价膜的分离性能,在此基础上采用分子动力学模拟方法从微观角度分析二次聚合膜的稳定性.     

芴酮引发光接枝改性LDPE膜的研究

采用紫外光引发接枝表面改性的方法,以芴酮(FL)为引发剂,在低密度聚乙烯(LDPE)薄膜表面上接枝丙烯酸(AA)、甲基丙烯酸(MAA)、丙烯酸甲酯(MA)、甲基丙烯酸甲酯(MMA)、丙烯酰胺(AM)等单体,以赋予薄膜表面新的化学性质.考察了引发剂浓度、紫外光的辐照时间、辐照强度、单体种类对LDPE薄膜接枝程度的影响.结果表明,在一定范围内,增加芴酮浓度,可以提高单体的接枝率,但当芴酮浓度达到5%时,接枝率反而下降.延长辐照时间至4 min和提高紫外光的辐照强度达100 W/m2,均有利于接枝反应的进行.不同单体在LDPE膜上的接枝能力与单体的活性、单体与基材的相容性等因素有关.接枝后,LDPE与水的接触角下降程度不仅与单体在膜上的接枝量有关,还与接枝单体的亲水性能密切相关.     

Study on the thin-film composite nanofiltration membrane for the removal of sulfate from concentrated salt aqueous: Preparation and performance

Thin-film composite (TFC) nanofiltration (NF) membrane was prepared through the interfacial polymerization between piperazine (PIP) and trimesoyl chloride (TMC) on the polysulphone support membrane. The chemical structure of membrane surface was studied by attenuated total reflectance infrared (ATR-IR) and X-ray photoelectronic spectroscopy (XPS). Parametric studies were conducted by varying reaction time, curing temperature, curing time and additives in PIP solution for obtaining the optimum polymerization conditions. Systematic performance studies were conducted with different feed solutions, feed concentrations, feed pHs, operating temperatures and pressures. Continuous and comparative tests were also conducted to determine the performance stability and separation efficiency of the thin-film composite NF membrane prepared. High performance thin-film composite NF membrane for the selective sulfate removal from concentrated sodium chloride aqueous with the water permeability coefficient of 75 L/(m² h MPa) could be prepared under specific conditions. Experimental results on concentrated mixed solution of NaCl and Na₂SO₄ demonstrated that the NF membrane developed could be successfully used for the removal of sodium sulfate from the concentrated brine of chloralkali industry with high permeate flux, selectivity and performance stability.     

Fabrication and development of interfacial polymerized thin-film composite nanofiltration membrane using different surfactants in organic phase; study of morphology and performance

The effects of addition of cationic cetyltrimethylammonium bromide (CTAB), non-ionic (Triton X-100) and anionic sodium dodecyl sulfate (SDS) surfactants in organic phase for preparing the composite nanofiltration membranes were investigated. The interfacial polymerization technique was employed by applying trimesoyl chloride (TMC) and piperazine (PIP) as the reagents for the preparation of poly(piperazineamide) on a UF support. The obtained thin layer membranes were placed in oven for 2 min at 70 °C. Water permeation performance, salt rejection, membrane surface charge, chemical structure and membrane morphology including top surface and cross-section were investigated for characterization of the prepared membranes using IR-ATR, SEM, filtration and zeta potential measurement. The prepared membranes using SDS showed higher flux compared to the other membranes. SEM surface images demonstrate some defects and cracks on the thin layer surface of the membrane prepared with SDS. For membrane containing CTAB, the salt rejection increased in the order of Na₂SO₄ > NaCl > MgCl₂ with variation around 50–90%.     

Two-Dimensional LDH Film Templating for Controlled Preparation and Performance Enhancement of Polyamide Nanofiltration Membranes

Tailored design of high-performance nanofiltration membranes that can be used in a variety of applications such as water desalination, resource recovery, and sewage treatment is desirable. Herein, we describe the use of layered double hydroxides (LDH) intermediate layer to control the interfacial polymerization between trimesoyl chloride (TMC) and piperazine (PIP) for the preparation of polyamide (PA) membrane. The dense surface of LDH layer and its unique mass transfer behavior influence the diffusion of PIP, and the supporting role of the LDH layer allows the formation of ultrathin PA membranes. By only changing the concentration of PIP, a series of membranes with controllable thickness from 10 to 50 nm and tunable crosslinking-degree can be prepared. The membrane prepared with a higher concentration of PIP shows excellent performance for divalent salt retention with water permeance of 28 Lm⁻² h⁻¹ bar⁻¹, high rejection of 95.1 % for MgCl₂ and 97.1 % for Na₂SO₄. While the membrane obtained with a lower concentration of PIP can sieve dye molecules of different sizes with a flux of up to 70 Lm⁻² h⁻¹ bar⁻¹. This work demonstrates a novel strategy for the controllable preparation of high-performance nanofiltration membranes and provides new insights into how the intermediate layer affects the IP reaction and the final separation performance.     

磺化纤维素纳米纤维多孔膜支撑的高通量纳滤膜的制备及脱盐性能

以细菌纤维素为原材料, 先后通过NaIO₄和NaHSO₃氧化还原反应制备了表面部分磺酸化的细菌纤维素(SBC)纳米纤维. 利用SBC纳米纤维多孔膜替代传统的超滤膜作为支撑底膜, 结合界面聚合反应调控制得复合纳滤膜, 并对其纳滤性能进行研究. 结果表明, 制备得到了对Na₂SO₄和MgSO₄具有高截留率(>96%)和超高分离通量(>320 L·m ^-2·h ^-1·MPa ^-1)的新型纳滤膜.     

Fabrication and Performance of a Low Operating Pressure Nanofiltration Poly（vinyl chloride） Hollow Fiber Membrane

A low operating pressure nanofiltration membrane is prepared by interfacial polymerization between m-phenylenediamine(MPDA) and trimesoyl chloride(TMC) using PVC hollow fiber membrane as supporting.A series of PVC nanofiltration membranes with different molecular weight cutoff(MWCO) can be obtained by controlling preparation conditions.Chemical and morphological characterization of the membrane surface was carried out by FTIR-ATR and SEM.MWCO was characterized by filtration experiments.The preparation conditions were investigated in detail.At the optimized conditions(40 min air-dried time,aqueous phase containing 0.5% MPDA,0.05% SDS and 0.6% acid absorbent,oil phase containing 0.3% TMC,and 1 min reaction time),under 0.3 MPa,water flux of the gained nanofiltration membrane reaches 17.8 L/m2·h,and the rejection rates of methyl orange and MgSO4 are more than 90% and 60%,respectively.     

Synthesis and characterization of crosslinked uniform polymeric microspheres containing a polyimide prepolymer by a new emulsification process

A highly crosslinked poly(styrene–divinyl benzene–trimethyolpropane trimethacrylate) microsphere containing a polyimide prepolymer (PIP) was prepared by a new emulsification method, Shirasu porous glass (SPG) membrane emulsification, and a subsequent radical suspension polymerization. That is, a mixture of styrene, divinyl benzene, trimethyol propane trimethacrylate (TMPTMA), and PIP containing an initiator was permeated through the uniform pores of the SPG membrane into a continuous phase containing a stabilizer to form uniform droplets. Then, the suspension polymerization was carried out at 65 °C for 24 h. The trifunctional crosslinker TMPTMA was added to enhance the destructive strength of the microsphere, and PIP was incorporated into the microsphere to provide an adhesion force by a known self‐curing reaction at 220 °C. The effects of the feed amounts of TMPTMA and PIP on the monomer conversion, size distribution, and destructive strength of the microsphere were investigated. The monomer conversion increased with an increase in TMPTMA. The particle size distribution became narrower as the TMPTMA feed amount increased, but it became broader with an increase in PIP. The destructive strength increased with increases in TMPTMA and PIP. After a heat treatment at 220 °C, the destructive strength decreased because of the heat degradation of the polymer. The addition of TMPTMA suppressed the heat degradation, and PIP could undergo self‐curing at 220 °C. The obtained highly crosslinked uniform microsphere containing PIP has potential applications in liquid‐crystal displays. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2588–2598, 2003     

三(2,6-二叔丁基-4-甲基-苯氧基)镧催化ε-己内酯低温聚合特征及与环碳酸酯嵌段共聚

摘要用三(2,6-二叔丁基-4-甲基-苯氧基)镧[La(OAr)₃]在-15 ℃引发ε-己内酯(CL)的开环聚合, 发现聚合体系具有活性聚合特征. 在第二步聚合过程中继续补加第二种单体三亚甲基环碳酸酯(TMC)或二甲基三亚甲基环碳酸酯(DTC), 可得到CL与环碳酸酯的嵌段共聚物.