钛纳米管负载锰催化剂的低温选择性催化还原脱硝性能

采用水热法合成了钛纳米管（TiNT）,以400℃焙烧后得到的TiO₂纳米管为载体,采用浸渍法制备了MnO_x/TiNT催化剂,用于低温NH₃选择性催化还原脱NO反应（SCR）。BET、TEM、XRD及TG测试表明,经过400℃焙烧之后的钛纳米管主要成分为锐钛矿型TiO₂,所制备的催化剂活性组分分散性较好。在模拟烟气条件下,考察了锰负载量、空速、O₂含量、氨氮比及进口NO浓度对MnO_x/TiNT的SCR催化性能的影响。在150℃、\[NH₃\]/\[NO\]比为1.2、O₂浓度为3%、NO浓度为0.06%、空速GHSV为23613.8h^-1、Mn的负载量为5%~15%的条件下,NO的转化率达到95%以上。反应气氛中单独通入水会造成催化剂的活性下降;切断H₂O,催化剂的活性可以恢复至初始水平。温度越高,催化剂抗水性能越好,而且水存在情况下的抗硫性能优于其单独抗硫性能。再次切断H₂O和SO₂,催化剂的活性逐渐上升,但不能恢复到初始水平。     

全氟磺酸功能化碳纳米管的制备及其催化性能

采用全氟磺酸-全氟乙烯共聚物的液相沉积方法制备了全氟磺酸功能化碳纳米管催化剂,利用N2吸附、扫描电子显微镜、透射电子显微镜、傅里叶变换红外光谱以及酸碱滴定等方法对材料的结构和酸性进行了表征,考察了温度和溶剂对催化剂稳定性的影响.结果表明,催化剂在极性和非极性溶液中均十分稳定,并且具有良好的热稳定性,使用温度可达300°C.该催化剂在对苯二酚与叔丁醇的烷基化反应中表现出优异的催化性能,其催化活性与稳定性均高于聚苯乙烯磺酸功能化的碳纳米管催化剂.     

Fabrication of p/n heterojunctions by electrochemical deposition of Cu2O onto TiO2 nanotubes

This work describes the TiO₂ nanotubes formation by anodic oxidation under different experimental conditions and the following attempts to optimize the electrochemical deposition of Cu₂O within the nanotubular structure. The as-formed Cu₂O/TiO₂ interface is a p/n junction that could be used in various light-assisted devices. The effect of the F^– concentration, the polarization duration and the post-thermal treatment on the TiO₂ nanotubes is recalled. Then the electrochemical deposition of cuprous oxide is investigated by cyclic voltammetry and the influence of the pH on the morphology and crystal structure is studied. Finally, potential pulses were applied to optimize the Cu₂O film morphology in order to improve the nanotubes covering.     

TiO2 nanotubes: synthesis and applications

TiO(2) is one of the most studied compounds in materials science. Owing to some outstanding properties it is used for instance in photocatalysis, dye-sensitized solar cells, and biomedical devices. In 1999, first reports showed the feasibility to grow highly ordered arrays of TiO(2) nanotubes by a simple but optimized electrochemical anodization of a titanium metal sheet. This finding stimulated intense research activities that focused on growth, modification, properties, and applications of these one-dimensional nanostructures. This review attempts to cover all these aspects, including underlying principles and key functional features of TiO(2), in a comprehensive way and also indicates potential future directions of the field.     

The photocatalytic and thermal catalytic reduction of CO2 with H2 over Pt/TiO2 catalysts

浸渍法制备了Pt负载量为0.5 to 2%的Pt/TiO2催化剂,考察它们在光照和加热条件下二氧化碳催化加氢性能.结果表明,二氧化碳加氢反应均可在Pt/TiO2的催化下进行,但在不同反应条件下加氢反应通过不同方式进行.在加热条件下,二氧化碳可转化为一氧化碳和甲烷,且在低温加热条件下一氧化碳是主产物(CO选择性为100%,250℃,0.5%Pt/TiO2).在1.5%Pt/TiO2催化剂上,当反应温度从250℃升高到450℃时,CH4的选择性由0增加到60.94%.同时,增加Pt的负载量也会导致CH4的选择性的增加.然而,在光照条件下,产物只有甲烷.CO2-TPD结果表明,二氧化碳通过羰基基团与作为吸附中心的Pt相连接.结合催化活性与表征结果,提出在光照条件下,反应可能以二氧化碳和氢气分别被光生电子活化反应生成甲酸中间体,随后经由甲酸加氢和脱水生成甲烷的机理进行.而在加热条件下,反应可能以二氧化碳首先吸附在催化剂表面形成羰基Pt物种,随后加氢生成一氧化碳,一氧化碳继续加氢生成甲烷的机理进行.     

Brookite-type TiO(2) nanotubes

Brookite-type TiO(2) nanotubes with crystalline multilayer walls have been synthesized for the first time via a simple hydrothermal route.     

二氧化钛纳米管的制备与光催化活性

用阳极氧化法,室温条件下在含NH4F和H2O的电解液(丙三醇+NH4F+H2O;乙二醇+NH4F+H2O)中制备了TiO2纳米管阵列。用环境扫描电子显微镜(SEM)、X射线衍射仪(XRD)表征二氧化钛纳米管阵列的微观形貌和物相结构。在丙三醇电解液中,电压为60 V,65 V,70 V,75 V制备的纳米管直径依次为160、170、190、220 nm。对甲基橙(10 mg/L)降解测试TiO2纳米管阵列的光催化性能。研究结果表明:在100 V阳极电压制备经过500℃退火处理后的TiO2纳米管阵列的光催化效果最好,其光催化降解率在光照时间120 min时达到89.2%。     

CVD synthesis of spiral carbon nanotubes over asymmetric catalytic particles

The influence of asymmetric catalytic particles prepared by various methods was investigated on the growth of spiral carbon nanotubes using the CVD method. Asymmetric particles were prepared by either milling or crystallization from oversaturated solution onto the surface of catalyst support or catalyst impregnation at pH 8–9. As-prepared catalysts were tested in the decomposition of acetylene. Carbon deposit, thus carbon nanotubes and spirals were observed by transmission electron microscopy the activity was characterized by carbon yield.     

负载Cu氧化铝纳米管合成及在NO+CH4反应中催化性能研究

采用过氧化氢调节反应条件,在水热体系中合成了新型的勃姆石纳米管,经520℃焙烧2h后,晶型由AlOOH转化为γ-Al2O3;采用XRD、氮吸附、TEM等对合成的纳米管进行表征.结果表明,合成的γ-Al2O3纳米管长约300nm,外径20nm,比表面积达到230m2/g以上.以此为载体,采用等体积浸渍法用Cu(NO3)2...     

光稳定二氧化钛纳米管负载钯催化剂光降解甲基橙过程中的活性物种(英文)

采用光沉积法制备了光稳定二氧化钛纳米管负载钯催化剂.通过X射线衍射、紫外-可见漫反射光谱、透射电子显微镜(TEM)、氮气吸附-脱附、X射线光电子能谱(XPS)、光致发光光谱和光电流等表征手段研究了催化剂的结构和性质.TEM表明二氧化钛纳米管经光照后仍然保持良好的管状结构;XPS结果表明大部分Pd以零价形式存在.以甲基橙溶液作为模拟废液研究了催化剂在紫外光及模拟日光条件下的光催化活性.当Pd的负载量为0.3 wt%时,催化剂的光催化活性最高并且优于P25的光催化活性.另外,通过在光降解过程中加入不同的捕获剂研究了不同氧化活性组分的作用.结果表明,光生空穴(hrb+)在光催化降解过程中起主要作用.     

Photocatalytic reduction of nitrate over TiO2 and Ag-modified TiO2

This research work presents the efficiency of the TiO₂ and Ag–TiO₂ thin films prepared by the sol–gel method and coated onto the surface of 304 stainless steel sheets used in the photocatalytic nitrate reduction processes. The Ag–TiO₂ thin films had the weight by weight (w/w) ratio of Ag⁺/TiO₂ of 0.1% as Ag atom. The XRD results showed that the crystalline phase structure of TiO₂ on the Ag–TiO₂ thin films was anatase. The optical band gaps of the TiO₂ and 0.1% Ag–TiO₂ thin films were respectively 3.27 and 2.70 eV, while the surface of the prepared catalysts was hydrophobic with the respective average water contact angles of 94.8° and 118.5° for the TiO₂ and 0.1% Ag–TiO₂ thin films. The net efficiencies of photocatalytic nitrate reduction of TiO₂ and 0.1% Ag–TiO₂ were 41.4% and 70.0%, respectively. The loading of Ag only influenced the nitrate removal efficiency without affecting the stoichiometric ratio of formate to nitrate. The net stoichiometric ratio of formate to nitrate of all experiments was 2.8:1.0, which is close to the stoichiometric ratio of 2.5:1.0 of the nitrate reduction to nitrite and then to nitrogen gas.     

Synthesis and characterization of ultrahigh crystalline TiO2 nanotubes

Ultrahigh crystalline TiO2 nanotubes were synthesized by hydrogen peroxide treatment of very low crystalline titania nanotubes (TiNT-as prepared), which were prepared with synthesized TiO2 nanoparticles by hydrothermal methods in an aqueous NaOH solution. Thus, prepared ultrahigh crystalline TiO2 nanotubes (TiNT-H2O2) showed comparable crystallinity with high crystalline TiO2 nanoparticles. The details of nanotubular structures were elucidated by high resolution-transmission electron microscopy (HR-TEM), field emission-scanning electron microscopy (FE-SEM), energy-dispersive X-ray analysis in transmission electron microscopy (TEM-EDX), X-ray diffraction (XRD), photoluminescence (PL), and BET surface area. TiNT-H2O2 was found to be a multiwalled anatase phase only with an average outer diameter of approximately 8 nm and an inner diameter of approximately 5 nm and grown along the [001] direction to 500-700 nm long with an interlayer fringe distance of ca. 0.78 nm. The photocatalytic activity of TiNT-H2O2 was about 2-fold higher than those of TiNT-as prepared, synthesized TiO2 nanoparticles, and TiO2-P25 (Degussa) in the photocatalytic oxidation of trimethylamine gas under UV irradiation.     

TiO2 (Anatase) films nanotubes

Anatase titanium dioxide nanotubes were prepared by hydrothermal synthesis with subsequent annealing in a nitrogen atmosphere. The outer diameter of particles is 10–15 nm, their inner diameter is 4–6 nm, and their length is several hundreds of nanometers. The structural transformation of polytitanic acid to TiO₂, which preserves the tubular morphology until 500°C, was studied by X-ray powder diffraction and thermal analyses, scanning and transmission electron microscopies, and IR and Raman spectroscopies.     

不同晶相TiO2负载Cu2O催化甲醛乙炔化反应

分别以金红石相和锐钛矿相TiO₂为载体, 采用液相还原-沉积法制备了Cu₂O/TiO₂催化剂. 采用氮气物理吸附-脱附(N₂-physisorption)实验、 氢气程序升温还原(H₂-TPR)、 X射线衍射(XRD)、 X射线光电子能谱(XPS)、 CO红外光谱(CO-IR)及高分辨透射电子显微镜(HRTEM)等技术, 研究了不同晶相TiO₂载体对Cu₂O/TiO₂结构及其催化甲醛乙炔化反应性能的影响. 结果表明, 以金红石相TiO₂为载体的催化剂炔化活性明显高于以锐钛矿相TiO₂为载体的催化剂, 原因在于金红石相TiO₂主要暴露(110)晶面, 其与铜物种的配位环境及较高的空位密度形成了更多的Cu—O—Ti结构物种, 表现为Cu₂O与TiO₂之间强的相互作用. 这导致Cu₂O高效转变为乙炔亚铜活性物种, 并保持了较高的分散度与稳定性, 抑制了过度还原物种金属Cu的生成, 进而使催化剂表现出较高的催化性能.