Dissolved Cu(II) Speciation in Unpolluted Soil Solutions of a Planosolic Horizon

Dissolved Cu(II) speciation in unpolluted soil solutions from different horizons was studied using differential pulse anodic stripping voltammetry (DPASV). Three sites were selected according to topography and monitored for three years. Experiments evidence Cu(II) can be bound by DOM (Dissolved Organic Matter) through complexation and/or adsorption reactions. The complexation capacity and the corresponding conditional stability constant were determined for complexation reactions. The adsorbing sites were titrated. A potential binding coefficient was calculated to compare both types of reactions. Results show adsorption is less frequent than complexation but exhibits higher binding coefficient.     

Development of an anodic stripping voltammetric assay, using a disposable mercury-free screen-printed carbon electrode, for the determination of zinc in human sweat

This paper reports on the development of a novel electrochemical assay for Zn²⁺ in human sweat, which involves the use of disposable screen-printed carbon electrodes (SPCEs). Initially, SPCEs were used in conjunction with cyclic voltammetry to study the redox characteristics of Zn²⁺ in a selection of supporting electrolytes. The best defined cathodic and anodic peaks were obtained with 0.1 M NaCl/0.1 M acetate buffer pH 6.0. The anodic peak was sharp and symmetrical which is typical for the oxidation of a thin metal film on the electrode surface. This behaviour was exploited in the development of a differential pulse anodic stripping voltammetric (DPASV) assay for zinc. It was shown that a deposition potential of −1.6 V versus Ag/AgCl and deposition time of 60 s with stirring (10 s equilibration) produced a well-defined stripping peak with E_pa = −1.2 V versus Ag/AgCl. Using these conditions, the calibration plot was linear over the range 1 × 10⁻⁸ to 5 × 10⁻⁶ M Zn²⁺. The precision was examined by carrying out six replicate measurements at a concentration of 2 × 10⁻⁶ M; the coefficient of variation was calculated to be 5.6%. The method was applied to the determination of the analyte in sweat from 10 human volunteers. The concentrations were between 0.39 and 1.56 μg/mL, which agrees well with previously reported values. This simple, low-cost sensitive assay should have application in biomedical studies and for stress and fatigue in sports studies.     

Exfoliated Graphite Oxide Modified Electrode for the Selective Determination of Picomolar Concentration of Lead

We report the selective, picomolar determination of lead(II) ions using exfoliated graphite oxide (EGO) modified glassy carbon electrode. Exfoliated graphite oxide is the oxidized form of exfoliated graphite containing a variety of functional groups such as hydroxyl, phenolic and carboxyl groups. The EGO can be dispersed as a stable colloid in a wide range of pH, from 2 to 11. This leads to the flexibility of film formation on substrates and use of a variety of functional groups to complex lead ions. The analyte is preconcentrated and subsequently determined using differential pulse anodic stripping voltammetry. The factors influencing the determination of lead such as the pH of the analyte solution, preconcentration time and the thickness of EGO layer on the electrode surface have been optimized. Two linear ranges are observed between 1 mM and 10 μm and 0.1 μM and 1 pM for a 5 minute preconcentration time. The lowest detection limit is found to be 1 pM. The main advantages of the electrode are the ease of preparation of the modified electrode, low cost, sensitivity and selectivity. The analytical utility of the EGO modified electrode in the determination of lead is demonstrated by application to several water samples.     

Evaluation of a carbon paste electrode modified with organofunctionalized amorphous silica in the cadmium determination in a differential pulse anodic stripping voltammetric procedure

The determination of cadmium using a carbon paste electrode modified with organofunctionalized amorphous silica with 2-benzothiazolethiol was investigated. The Cd(II) oxidation peak was observed around −0.80 V (vs. SCE) in phosphate buffer (pH 4.0) in differential pulse anodic stripping voltammetry. The best results were obtained under the following optimized conditions: 1 min accumulation time, 50 mV pulse amplitude, 20 mV s⁻¹ scan rate in phosphate buffer pH 4.0. Using such parameters a linear dynamic range from 5.6×10⁻⁷ to 3.5×10⁻⁵ mol l⁻¹ Cd(II) was observed with a sensitivity of 2.83 μA mol⁻¹ l, limit of detection 1.0×10⁻⁷ mol l⁻¹. Cd(II) spiked in a natural water sample was determined with 99% mean recovery at 10⁻⁷ mol l⁻¹ level. Interference were also evaluated.     

Hg(II) immobilized MWCNT graphite electrode for the anodic stripping voltammetric determination of lead and cadmium

The preparation of Hg(II)-modified multi walled carbon nanotube (MWCNT) by reaction of oxidized MWCNT with aqueous HgCl₂ was carried out. The Hg(II)-modified multi walled carbon nanotube (Hg(II)/MWCNT) dispersed in Nafion solution was used to coat the polished graphite electrode surface. The Hg(II)/MWCNT modified graphite electrode was held at a cathodic potential (−1.0 V) to reduce the coordinated Hg(II) to Hg forming nanodroplets of Hg. The modified electrode was characterized by FESEM/EDAX which provided useful insights on the morphology of the electrode. The SEM images showed droplets of Hg in the size of around 260 nm uniformly distributed on the MWCNT. Differential pulse anodic stripping voltammetry (DPASV) and electrochemical impedance spectroscopy were used to study the Hg(II) binding with MWCNT. Differential pulse anodic stripping voltammetry of ppb levels of cadmium and lead using the modified electrode yielded well-defined peaks with low background current under a short deposition time. Detection limit of 0.94 and 1.8 ng L⁻¹ were obtained following a 3 min deposition for Pb(II) and Cd(II), respectively. Various experimental parameters were characterized and optimized. High reproducibility was observed from the RSD values for 20 repetitive measurements of Pb(II) and Cd(II) (1.7 and 1.9%, respectively). The determination of Pb(II) and Cd(II) in tap water and Pb(II) in human hair samples was carried out. The above method of fabrication of Hg(II)/MWCNT modified graphite electrode clearly suggests a safe route for preparing Hg immobilized electrode for stripping analysis.     

Simultaneous determination of chromium(III) and cadmium(II) by differential pulse anodic stripping voltammetry on a stannum film electrode

A stannum film electrode has been developed for the simultaneous determination of trace levels of chromium(III) and cadmium(II) by differential pulse anodic stripping voltammetry (DPASV). The stannum film electrode was generated in situ by depositing simultaneously the stannum film and the metals obtained by reduction of Cd(II) and Cr(III) at −1.4 V on a glassy carbon electrode. Then, the reduced products were oxidized by scanning the potential of the electrode from −1.4 to −0.4 V using DPASV. The electrode exhibited well-defined and separated stripping signals for both metals accompanied with a low background contribution. The possible mechanism of this design was proposed. Under the optimized working conditions, the detection limit was 2.0 and 1.1 μg l⁻¹ for Cr(III) and Cd(II) at a deposition time of 3 min. Finally, the stannum film electrode was successfully applied to the determination of Cd(II) in tap water with satisfactory results.     

Anodic Stripping Voltammetry of Heavy Metals at Nanocrystalline Boron‐Doped Diamond Electrode

Boron‐doped Diamond (BDD) electrode has become one of the important tools for heavy metal detection. By studying some analytical parameters of DPASV method, like deposition time and potential in different electrolyte concentrations (acetate buffer), the conditions for detecting very low metal ion levels (Zn, Cd, Pb, and Cu) could be chosen. Diluted electrolyte (0.01 M buffer) was one of the factors favoring low detection and quantification limits, but its quantification range is short in comparison to more concentrated media. For ?1.7 V deposition potential, the detection of single metal at ppb levels was reached in 60 s deposition time. Understanding different metal‐metal interactions shows the limits to the simultaneous determination of heavy metals at BDD. Quantification was possible for the simultaneous determination of Zn, Cd and Pb despite the overlapping of Zn and Cd peaks. The performance of the BDD was compared with that of another C‐based solid electrode: the glassy carbon electrode (without mercury plating). A lower base line current, wider potential range, higher sensitivity (3 to 5 times higher than GC) and longevity of the material were noticed for the BDD.     

Proposal for a mercury isolation procedure using cold vapor method in combination with voltammetric determination using a rotating gold electrode

The optimal process of pre-treatment and activation of gold rotating disc electrode (AuRDE) before voltammetric determination of mercury is proposed. This treatment encompasses polishing of the electrode surface, electrochemical cycling, and activation. This procedure both increases determination sensitivity as well as improves determination reproducibility. The detection limit on the working electrode achieved using this approach amounted to 8.26·10⁻¹⁰ mol L⁻¹for direct mercury determination in water solution (applying 200 s running accumulation). The procedure of the quantitative mercury isolation from complicated sample matrix was developed as well. It provides better selectivity and significant increase of sensitivity of mercury determination. In case of mercury isolation from one liter of water the detection limit is 6.23·10⁻¹¹ mol L⁻¹ (analyzing a greater sample volume the determined concentration could be lower).      

Influence of molar mass distribution on the complexation of heavy metals by humic material

The association of the heavy metals zinc(II) and cadmium(II) with humic acids of different molar mass distributions has been studied by differential pulse anodic stripping voltammetry. The various humic acid samples were obtained using an experimental procedure in which an untreated Fluka humic acid sample was fractionated by pH variation. Flow field-flow fractionation was used to characterize the humic acid samples with respect to the molar distributions, which appeared to be relatively wide for all samples. The voltammetric analysis of the binding properties of the various samples for zinc(II) and cadmium(II) yielded similar values for the mean stability of the metal complex which thus appears to be independent of the molar mass distribution of the sample. Differences in the shape of the voltammetric complexation curves were the result of differences in the mean diffusion coefficients of the humics involved.     

A voltammetric sensor for simultaneous determination of lead,cadmium and zinc on an activated carbon fiber rod

A simple, low cost and sensitive voltammetric sensor was developed for the simultaneous detection of Pb²⁺, Cd²⁺, and Zn²⁺ based on a disposable carbon fiber rod (CFR). The important factors to enhance the sensing property were creation of a clean surface by dealing with CFR at a high potential and electrochemical deposition of Bi film to improve the accumulation of heavy metal ions.     

TpPa-1/Nafion修饰电极的差分脉冲阳极溶出伏安法同时测定铜离子和汞离子

通过机械化学合成法合成了一种共价有机框架材料TpPa-1,以此作为电极材料制备化学修饰电极,研究了修饰电极的差分脉冲阳极溶出伏安法(DPASV)同时测定铜离子和汞离子。结果表明,TpPa-1/Nafion修饰电极在磷酸盐缓冲溶液中可实现对Cu^2+和Hg^2+的同时检测。Cu^2+的检出限为5.0×10^-8 mol/L线性范围为1.0×10^-7~5.0×10^-5 mol/L,R^2=0.9975。Hg^2+的检出限为1.0×10^-8 mol/L,线性范围为2.0×10^-8~1.0×10^-4 mol/L,R^2=0.9988。采用上述方法对实际样品进行检测,回收率为97.6%~105.5%,RSD均小于4.0%。     

High Sensitivity and Reproducibility of a Bismuth/Poly(bromocresol purple) Film Modified Glassy Carbon Electrode for Determination of Trace Amount of Cadmium by Differential Pulse Anodic Stripping Voltammetry

This work described a novel type of bismuth/poly(bromocresol purple) film modified glassy carbon electrode (denoted as Bi/Poly(BCP)/GCE) for anodic stripping analysis of trace Cd²⁺. The Bi/Poly(BCP)/GCE was fabricated in situ by depositing simultaneously bismuth and cadmium by reduction at ?1.20 V on the poly(BCP) film using a differential pulse voltammetry. Under the optimum conditions, the anodic stripping peak current response increased linearly with the Cd²⁺ concentrations in a range of 2.0×10^?8–1.0×10^?7 M and 1.0×10^?7–6.0×10^?6 M in 0.1 M NaAc‐HAc buffer solution (pH 5.0) with the detection limit of 6.5×10^?9 M (S/N=3). The Bi/poly(BCP)/GCE performed good reproducibility and high sensitivity. Finally, this proposed method was successfully applied to determine the concentration of Cd²⁺ in water samples.     

Ultrasensitive and simultaneous detection of heavy metal ions based on three-dimensional graphene-carbon nanotubes hybrid electrode materials

A green and facile method was developed to prepare a novel hybrid nanocomposite that consisted of one-dimensional multi-walled carbon nanotubes (MWCNTs) and two-dimensional graphene oxide (GO) sheets. The as-prepared three-dimensional GO–MWCNTs hybrid nanocomposites exhibit excellent water-solubility owing to the high hydrophilicity of GO components; meanwhile, a certain amount of MWCNTs loaded on the surface of GO sheets through π–π interaction seem to be “dissolved” in water. Moreover, the graphene(G)-MWCNTs nanocomposites with excellent conductivity were obtained conveniently by the direct electrochemical reduction of GO–MWCNTs nanocomposites. Seeing that there is a good synergistic effect between MWCNTs and graphene components in enhancing preconcentration efficiency of metal ions and accelerating electron transfer rate at G-MWCNTs/electrolyte interface, the G-MWCNTs nanocomposites possess fast, simultaneous and sensitive detection performance for trace amounts of heavy metal ions. The electrochemical results demonstrate that the G-MWCNTs nanocomposites can act as a kind of practical sensing material to simultaneously determine Pb²⁺ and Cd²⁺ ions in terms of anodic stripping voltammetry (ASV). The linear calibration plots for Pb²⁺ and Cd²⁺ ranged from 0.5 μg L⁻¹ to 30 μg L⁻¹. The detection limits were determined to be 0.2 μg L⁻¹ (S/N = 3) for Pb²⁺ and 0.1 μg L⁻¹ (S/N = 3) for Cd²⁺ in the case of a deposition time of 180 s. It is worth mentioning that the G-MWCNTs modified electrodes were successfully applied to the simultaneous detection of Cd²⁺ and Pb²⁺ ions in real electroplating effluent samples containing lots of surface active impurities, showing a good application prospect in the determination of trace amounts of heavy metals.     

Palladium Particles‐Impregnated Natural Phosphate Electrodes for Electrochemical Determination of Mercury in Ambient Water Samples

We present here a simple procedure for the determination of mercury(II) using differential pulse anodic stripping voltammetry (DPASV) at palladium particles‐impregnated natural phosphate modified carbon paste electrodes (Pd‐NP‐CPE). The surface of modified electrode was characterized using SEM, infrared spectroscopy, X‐ray diffraction and electrochemical analysis. All experimental variables involved in the voltammetric stripping method were optimized. The detection limit was found to be 4.99×10^?8 mol L^?1 (S/N=3) that is not different to the permitted value for Hg(II) in water reported by the Environmental Protection Agency (EPA). The proposed electrode exhibits good applicability for monitoring Hg(II) in tap and wastewater.     

Simultaneous determination of lead(II) and cadmium(II) at a diacetyldioxime modified carbon paste electrode by differential pulse stripping voltammetry

A simple and effective chemically modified carbon paste electrode (CMCPE) for the simultaneous determination of lead(II) and cadmium(II) was developed in this work. The electrode was prepared by the addition of diacetyldioxime into a carbon paste mixture. Pb²⁺ and Cd²⁺ were preconcentrated on the surface of the modified electrode by complexing with diacetyldioxime and reduced at a negative potential (−1.10 V). Then the reduced products were oxidized by differential pulse stripping. The fact that two stripping peaks appeared on the voltammograms at the potentials of −0.65 V (Cd²⁺) and −0.91 V (Pb²⁺) demonstrates the possibility of simultaneous determination of Pb²⁺ and Cd²⁺. Under the optimized working conditions, calibration graphs were linear in the concentration ranges of 1.0×10⁻⁷-1.5×10⁻⁵ mol l⁻¹ (Pb²⁺) and 2.5×10⁻⁷-2.5×10⁻⁵ mol l⁻¹ (Cd²⁺), respectively. For 5 min preconcentration, detection limits of 1×10⁻⁸ mol l⁻¹ (Pb²⁺) and 4×10⁻⁸ mol l⁻¹ (Cd²⁺) were obtained at the signal noise ratio (SNR) of 3. To evaluate the reproducibility of the newly developed electrode, the measurements of 5×10⁻⁷ mol l⁻¹ Pb²⁺ and Cd²⁺ were parallel carried out for six times at different electrodes and the relative standard deviations were 2.9% (Pb²⁺) and 3.2% (Cd²⁺), respectively. Interferences by some metals were investigated. Only Ni²⁺ and Hg²⁺ apparently affected the peak currents of Pb²⁺ and Cd²⁺. The diacetyldioxime modified carbon paste electrode was applied to the determination of Pb²⁺ and Cd²⁺ in water samples. The results indicate that this electrode is sensitive and effective for the simultaneous determination of Pb²⁺ and Cd²⁺.     

Sensitive Voltammetric Determination of Cadmium(II) with 8‐Hydroxyquinoline and Ionic Liquid Modified Carbon Paste Electrode

In this paper 8‐hydroxyquinoline (HQ) and ionic liquid (IL) modified carbon paste electrode was fabricated and used for the sensitive determination of cadmium(II) with differential pulse anodic stripping voltammetry (DPASV). The modified electrode was prepared by the addition of HQ and IL 1‐ethyl‐3‐methylimidazoliam ethylsulphate as the modifiers into the traditional carbon paste mixture. Cd(II) was preconcentrated and reduced on the surface of the modified electrode at the potential of ‐1.0 V (vs. SCE) by the co‐contributions from the formation of HQ‐Cd(II) complex and the accumulation effect of IL. Then the reduced Cd on the electrode surface was reoxidized by DPASV with a sensitive oxidation peak appeared at ‐0.79 V (vs. SCE). Under the optimal conditions the oxidation peak current was proportional to the Cd(II) concentration in the range from 0.03 to 2.0 mol/L with the detection limit as 5.0 nmol/L (3σ). The proposed method was successfully applied to the water samples detection with the recovery in the range from 95.6% to 96.6%.     

Application of computer imaging,stripping voltammetry and mass spectrometry to study the effect of lead (Pb-EDTA) on the growth and viability of early somatic embryos of Norway spruce (<Emphasis Type="Italic">Picea abies</Emphasis> /L./ Karst.)

Image analysis (IA) was used to determine the areas and circumferences of clusters of early somatic embryos (ESEs) of the Norway spruce (Picea abies /L./Karst.). Results obtained from IA were compared with the fresh weights of the ESE clusters and their esterase activities. The areas of the ESE clusters correlated well with both the increases in fresh weight (R ²=0.99) of the ESEs and their esterase activities (R ²=0.99). In addition, we studied the viability of the ESEs, which was determined by (a) double staining with fluorescein diacetate and propidium iodide (the resulting fluorescence was quantified by IA) and (b) determining esterase activity using a spectrofluorimetric detector. The results obtained with IA and esterase assay were comparable (the deviation between the tangents of the bisectors was 6.4%). IA was also used to study the effect of Pb–EDTA chelate (50, 250 and 500 μM) on the viability of the ESEs and on the growth of clusters. The presence of Pb–EDTA markedly slowed the growth of ESEs clusters (by more than 65% with 250 μM of Pb–EDTA after 288 h of cultivation) and decreased the viability of ESEs (by more than 30% with 500 μM of Pb–EDTA after 288 h of cultivation). The lead concentration in the ESEs was determined by differential pulse anodic stripping voltammetry and increased with the external lead concentration and the time of treatment from 100 to 600 pg Pb/100 mg of fresh weight of ESEs. Glutathione is a diagnostic marker of the influence of Pb–EDTA on ESEs and its content was determined by high–performance liquid chromatography coupled with mass spectrometry. The glutathione content changed linearly with treatment time and the applied external lead concentration. The highest glutathione content was obtained at 250 μM of Pb–EDTA after 192 h of cultivation.     

Simultaneous Quantitative Determination of Cadmium,Lead, and Copper on Carbon‐Ink Screen‐Printed Electrodes by Differential Pulse Anodic Stripping Voltammetry and Partial Least Squares Regression

Water is a vital commodity for every living entity on the planet. However, water resources are threatened by various sources of contamination from pesticides, hydrocarbons and heavy metals. This has resulted in the development of concepts and technologies to create a basis for provision of safe and high quality drinking water. This paper focuses on the simultaneous quantitative determination of three common contaminants, the heavy metals cadmium, lead and copper. Multivariate calibration was applied to voltammograms acquired on in‐house printed carbon‐ink screen‐printed electrodes by the highly sensitive electrochemical method of differential pulse anodic stripping voltammetry (DPASV). The statistically inspired modification of partial least squares (SIMPLS) algorithm was employed to effect the multivariate calibration. The application of data pretreatment techniques involving range‐scaling, mean‐centering, weighting of variables and the effects of peak realignment are also investigated. It was found that peak realignment in conjunction with weighting and SIMPLS led to the better overall root mean square error of prediction (RMSEP) value. This work represents significant progress in the development of multivariate calibration tools in conjunction with analytical techniques for water quality determination. It is the first time that multivariate calibration has been performed on DPASV voltammograms acquired on carbon‐ink screen‐printed electrodes.     

槲皮素在聚谷氨酸修饰玻碳电极上的伏安行为及检测

制备了聚谷氨酸修饰玻碳电极,通过循环伏安法和差分脉冲伏安法研究了槲皮素在该修饰电极上的电化学行为。在pH 5.00的B-R缓冲液中,槲皮素在修饰电极上于0.28 V(vs Ag/AgCl)电位处产生一个灵敏的DPV阳极氧化峰,氧化峰电流与槲皮素的浓度在1.0×10-8～5×10-5 mol/L的范围内呈良好的线性关系,最低检测限为4.0×10-9 mol/L。实验表明,聚谷氨酸修饰电极可提高槲皮素的检测灵敏度,该电极用于芦丁水解产物中槲皮素的检测,回收率为103.4%～104.5%。     

Thiol‐Functionalized Silica Thin Film Modified Electrode in Determination of Mercury Ions in Natural Water

The use of a thin thiol‐functionalized silica film modified glassy carbon electrode in the determination of Hg(II) ions in a natural water sample is described. A typical measurement involves two successive steps: a glassy carbon electrode coated with a thin mesoporous silica film containing 10% of mercaptopropyl groups, according to the MPTMS/TEOS ratio in the starting sol‐gel, was first immersed into the accumulation medium for 15 min, then removed, and finally transferred into a detection solution containing KCl 1.0 mol L^?1 where detection was performed by anodic stripping voltammetry. In this medium the previously accumulated Hg²⁺ species complexed by the thiol groups in an open circuit preconcentration step is then directly reduced at ?0.6 V during 60 s prior to be quantified by a differential pulse anodic scan from ?0.6 to 0.3 V (vs. Ag/AgCl). A stripping peak appeared at about ?0.01 V, which is directly proportional to the quantity of the analyte previously accumulated into the film. The best results were obtained under the following conditions: 100 mV pulse amplitude and 10 mV s^?1 scan rate in 1.0 mol L^?1 KCl solution pH 2.0. Using such parameters a linear dynamic range from 1.00 to 10.0×10^?8 mol L^?1 Hg(II) was observed with a limit of detection of 4.3 nmol L^?1 for an accumulation time of 15 min. Hg(II) spiked in a natural water sample was determined between 97.0 and 101.4% mean recovery at 10^?8 mol L^?1 level. The results indicate that this electrode is sensitive and selective for the Hg(II)determination.