Structural characterization of titanium oxide layers prepared by plasma based ion implantation with oxygen on Ti6Al4V alloy

Ti6Al4V alloy was implanted with oxygen by using plasma based ion implantation (PBII) at pulsed voltage ranging from −10 to −50 kV with a frequency of 100 Hz. In order to maintain a lower implantation temperature, an oil cooling working table was employed. The structure of the modified layers was characterized by X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. The results show that the thickness of the titanium oxide layer increases significantly with the increase of implanted voltage. The structure of the modified layer changes along depth. It is found that the surface layer consists of TiO₂, and the subsurface layer is a mixing structure of TiO_2, Ti₂O₃ and TiO. There is crystalline rutile phase existing in the modified layer of sample implanted at high implanted voltage. In addition, in the outmost modified surface, aluminum present as oxidized state, and vanadium could not be detected.     

Structure and tribological performance by nitrogen and oxygen plasma based ion implantation on Ti6Al4V alloy

Ti6Al4V alloy was implanted with nitrogen-oxygen mixture by using plasma based ion implantation (PBII) at pulsed voltage −10, −30 and −50 kV. The implantation was up to 6 × 10¹⁷ ions/cm² fluence. The changes in chemical composition, structure and hardness of the modified surfaces were studied by XPS and nanoindentation measurements. According to XPS, it was found that the modified layer was predominantly TiO₂, but contained small amounts of TiO, Ti₂O₃, TiN and Al₂O₃ between the outmost layer and metallic substrate. Surface hardness and wear resistance of the samples increased significantly after PBII treatment, the wear rate of the sample implanted N₂-O₂ mixture at −50 kV decreased eight times than the untreated one. The sample implanted N₂-O₂ mixture showed better wear resistance than that of the sample only implanted oxygen at − 50 kV. The wear mechanism of untreated sample was abrasive-dominated and adhesive, and the wear scar of the sample implanted at −50 kV was characterized by abrasive wear-type ploughing.     

Structure and micro-mechanical properties of helium-implanted layer on Ti by plasma-based ion implantation

The present paper concentrates on structure and micro-mechanical properties of the helium-implanted layer on titanium treated by plasma-based ion implantation with a pulsed voltage of −30 kV and doses of 3, 6, 9 and 12 × 10¹⁷ ions/cm², respectively. X-ray photoelectron spectroscopy and transmission electron microscopy are employed to characterize the structure of the implanted layer. The hardnesses at different depths of the layer were measured by nano-indentation. We found that helium ion implantation into titanium leads to the formation of bubbles with a diameter from a few to more than 10 nm and the bubble size increases with the increase of dose. The primary existing form of Ti is amorphous in the implanted layer. Helium implantation also enhances the ingress of O, C and N and stimulates the formations of TiO₂, Ti₂O₃, TiO, TiC and TiN in the near surface layer. And the amount of the ingressed oxygen is obviously higher than those of nitrogen and carbon due to its higher activity. At the near surface layer, the hardnesses of all implanted samples increases remarkably comparing with untreated one and the maximum hardness has an increase by a factor of up to 3.7. For the samples implanted with higher doses of 6, 9 and 12 × 10¹⁷ He/cm², the local displacement bursts are clearly found in the load-displacement curves. For the samples implanted with a lower dose of 3 × 10¹⁷ He/cm², there is no obvious displacement burst found. Furthermore, the burst width increases with the increase of the dose.     

First-principles calculations on implanted TiO<Subscript>2</Subscript> by 3d transition metal ions

3d transition metal (V, Cr and Fe) ions are implanted into TiO₂ by the method of metal ion implantation. The electronic band structures of TiO₂ films doped 3d transition metal ions have been analyzed by ab initio band calculations based on a self-consistent full-potential linearized augmented plane-wave method within the first-principle formalism. Influence of implantation on TiO₂ films is examined by the method of UV-visible spectrometry. The results of experiment and calculation show that the optical band gap of TiO₂ films is narrowed by ion implantation. The calculation shows that the 3d state of V, Cr and Fe ions plays a significant role in red shift of UV-Vis absorbance spectrum.     

Methylene blue photoelectrodegradation under UV irradiation on Au/Pd-modified TiO2 films

In this work TiO₂ thin films were modified with gold/palladium (Au/Pd) bimetallic paticles by sputtering method. TiO₂ films were deposited on ITO (SnO₂:In) by Doctor Blade method and post-anneling. The properties of the films were studied through measurements of XRD (X-ray diffraction) and AFM (atomic force microscopy). The degradation of methylene blue was studied by UV-irradiated pure TiO₂ and Au/Pd-modified TiO₂ in aqueous solution. Langmuir-Hinshelwood model was used to obtain kinetic information. Photocatalytic study indicated that Au/Pd-modified TiO₂ photocatalytic activity was better than TiO₂ pure; the best half-life time for Au/Pd-modified TiO₂ in photodegradation was 2.8 times smaller than TiO₂ pure; finally the efficiency in methylene blue photodegradation was improved from 23% to 43% when Au/Pd-modified TiO₂ films were used.     

Visible-light photocatalysis of nitrogen-doped TiO2 nanoparticulate films prepared by low-energy ion implantation

Nitrogen-doped TiO₂ (N-TiO₂) films were prepared by low-energy implantation of nitrogen ions into pulsed laser deposited anatase TiO₂ films. The anatase phase of the films was not changed by the implantation with very low energy of 200 eV. XPS measurements revealed that the implanted nitrogen species were mainly interstitial ones. The nitrogen concentration was increased with increasing ion flux which could be controlled by adjusting the gas flow rate of the ion source. All the produced N-TiO₂ films exhibited visible-light photocatalytic activities in degradation of methylene blue in aqueous solutions, indicating that interstitial nitrogen could also be responsible for the photocatalysis in visible region. Higher visible-light photocatalytic efficiency was achieved with higher implanted nitrogen concentration.     

N掺杂锐钛矿TiO2电子结构的第一性原理研究

为了研究N掺杂对锐钛矿型TiO₂电子结构的影响，进而揭示N掺杂导致锐钛矿型TiO₂的禁带宽度变小的机理，对N掺杂TiO₂进行了基于密度泛函理论的第一性原理研究. 通过对能带、态密度及电子分布密度图的分析，发现在N掺杂后，N原子与Ti原子在导带区，发生了强烈的相互关联作用，致使Ti原子3d轨道上的电子向N原子2p轨道发生移动，使得导带降低了，从而使得TiO₂导带的禁带宽度变小.理论预测可以发生红移现象，与实验结果对比分析，理论与实验基本相符. 关键词： N掺杂 2')" href="#">锐钛矿型TiO₂ 电子结构     

N掺杂锐钛矿TiO2光学性能的第一性原理研究

用平面波赝势方法(PWP)计算了N掺杂锐钛矿型TiO₂前后的光学特性,即介电函数虚部ε₂(ω)，光学吸收系数I(ω)和反射率R(ω). 并从能带结构上解释了为什么掺N后锐钛矿型TiO₂的光学谱在2.93，3.56和3.97eV处相对掺杂前会出现3个峰值的原因. 从光谱图上分析得出，掺杂后TiO₂要发生红移现象，实验现象证实了这一结果. 关键词： N掺杂 2')" href="#">锐钛矿型TiO₂ 光学性能 第一性原理     

Preparation of visible light responsive N doped TiO2 via a reduction-nitridation procedure by nonthermal plasma treatment

A visible light responsive N-doped TiO₂ was prepared via a reduction-nitridation procedure by nonthermal plasma treatment. X-ray diffraction, N₂ adsorption, UV-vis spectroscopy, photoluminescence, and X-ray photoelectron spectroscopy were used to characterize the prepared TiO₂ samples. The plasma treatment did not change the phase composition and particle sizes of TiO₂ samples, but extended its absorption edges to the visible light region. The photocatalytic activities were tested in the degradation of an aqueous solution of a reactive dyestuff, methylene blue, under visible light. The photocatalytic activities of TiO₂ prepared by reduction-nitridation procedure were much higher than that of samples prepared by simple nitridation treatment. The enhanced activity was ascribed to the substitutional N-doping and appropriate concentration of oxygen vacancies. TOHN10 prepared by reduction-nitridation procedure exhibited excellent photocatalytic stability. A possible mechanism for the photocatalysis was proposed.     

Enhanced photocatalytic degradation of Safranin-O by heterogeneous nanoparticles for environmental applications

Nanostructure titanium dioxide (TiO₂) has been synthesized by hydrolysis of titanium tetrachloride in aqueous solution and Ag-TiO₂ nanoparticles were synthesized by photoreduction method. The resulting materials were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier-transform infrared (FT-IR) and UV-vis absorption spectroscopy. The experimental results showed that the sizes of the synthesized TiO₂ and Ag-TiO₂ particles are in the range of 1.9-3.2 nm and 2-10 nm, respectively. Moreover, Ag-TiO₂ nanoparticles exhibit enhanced photocatalytic activity on photodegradation of Safranin-O (SO) dye as compared to pure TiO₂. The positive effect of silver on the photocatalytic activity of TiO₂ may be explained by its ability to trap electrons. This process reduces the recombination of light generated electron-hole pairs at TiO₂ surface and therefore enhances the photocatalytic activity of the synthesized TiO₂ nanoparticles. The effects of initial dye and nanoparticle concentrations on the photocatalytic activity have been studied and the results demonstrate that the dye photodegradation follows pseudo-first-order kinetics. The observed maximum degradation efficiency of SO is about 60% for TiO₂ and 96% for Ag-TiO₂.     

Structure and phase transformations caused by oxygen ion implantation into titanium

Secondary-ion mass spectrometry and transmission electron microscopy are used to investigate structural changes and phase transformations during ¹⁶O and ¹⁸O ion implantation into titanium at 100 and 300 K. For all implanted ion energies, there are the doses (saturation doses) after which the interstitial oxygen profile takes a final steady-state shape. The steady-state profile corresponds to a definite stable set of oxide phases, including TiO, rutile TiO₂, and TiO_1.5 layers. Under steady-state conditions, the film is composed of several oxide phases, whose structures depend on the target temperatures used in the irradiation process. At 100 K, the steady-state oxide system contains an amorphous phase layer with gas-filled bubbles instead of crystalline rutile.     

TiO2 Wedgy Nanotubes Array Flims for Photovoltaic Enhancement

In this study, TiO₂ wedgy nanotubes with rectangular cross-sections were fabricated on transparent conductive substrates by using TiO₂ nanorods as the precursor via the anisotropic etching route. TiO2 nanotubes with V-shaped hollow structure and the special crystal plane exposed on the tube wall possess nature of high surface area for more dye molecules absorption, and the strong light scattering effects and dual-channel for effective electron transport of the TiO₂ V-shaped nanotubes based dye-sensitized solar cell exhibit a remarkable photovoltaic enhancement compared with the TiO₂ nanorods. The photoanode based on our V-shaped TiO₂ nanotubes with a length of 1.5 μm show a 123% increase of the dye loading and a 182% improvement in the overall conversion efficiency when compared with 4 μm rutile TiO₂ nanorods photoanode.     

A combined experimental and theoretical analysis of Fe-implanted TiO2 modified by metal plasma ion implantation

Photocatalyst titanium dioxide (TiO₂) thin films were prepared using sol-gel process. To improve the photosensitivity of TiO₂ at visible light, transition metal of Fe was implanted into TiO₂ matrix at 20 keV using the metal plasma ion implantation process. The primary phase of the Fe-implanted TiO₂ films is anatase, but X-ray diffraction revealed a slight shift of diffraction peaks toward higher angles due to the substitutional doping of iron. The additional band gap energy levels were created due to the formation of the impurity levels (Fe-O) verified by X-ray photoelectron spectroscopy, which resulted in a shift of the absorption edge toward a longer wavelength in the absorption spectra. The optical band gap energy of TiO₂ films was reduced from 3.22 to 2.87 eV with an increase of Fe ion dosages from 0 to 1 × 10¹⁶ ions/cm². The band gap was determined by the Tauc plots. The photocatalysis efficiency of Fe-implanted TiO₂ was assessed using the degradation of methylene blue under ultraviolet and visible light irradiation. The calculated density of states for substitutional Fe-implanted TiO₂ was investigated using the first-principle calculations based on the density functional theory. A combined experimental and theoretical Fe-implanted TiO₂ film was formed, consistent with the experimentally observed photocatalysis efficiency of Fe-implanted TiO₂ in the visible region.     

Synthesis and photocatalytic property of N-doped TiO2 nanorods and nanotubes with high nitrogen content

Nano N-doped TiO₂ nanotubes were fabricated by hydrothermally treating N-doped TiO₂ nanorods in a 8 M NaOH solution at 110 °C for 20 h. The N-doped TiO₂ nanorods were synthesized by a solvothermal process with precursor solution containing titanium sulfate, urea, and dichloroethane. The N-doped TiO₂ nanorods and nanotubes were characterized with X-ray diffraction, transmission electron microscopy, and UV-vis spectrophotometry. The nitrogen contents of the N-doped TiO₂ nanorods and nanotubes were reached to high values of 36.9 at.% and 25.7 at.%, respectively. The nitrogen doping narrowed the band gap of the N-doped TiO₂ nanorods and nanotubes and introduced indirect band gap to the powders, which respectively extended the absorption edge to visible light and infrared region. The nanotubes showed larger specific surface area and greater degradation efficiency to methyl orange than the nanorods.     

Photodegradation of CH3I on mesoporous TiO2-B nanofibers with Au nanoparticles

Au nanoparticles deposited on mesoporous TiO₂-B nanofibers have been prepared, characterized, and used to catalyze photoreactions of iodomethane. High-density gold-particle deposition on TiO₂-B is obtained by electrostatic and/or chemical force between the particles of TiO₂-B and Au capped with -SC(H)(CO₂H)(CH₂CO₂H) through pH control. The capping groups on the gold particles can be removed after 400 °C calcination. It is found that the nature of the inorganic acids used for pH adjustment has effects on particle morphology and deposition. Two other methods, i.e., preparation of TiO₂-B nanofibers in the presence of gold particles and preparation of gold nanoparticles in the presence of TiO₂-B particles (deposition-precipitation method), are also investigated. However, the former method produces a low-density deposition and the latter one induces a morphology change of the TiO₂-B and an increase of the Au in size. Fourier transform infrared spectroscopy has been employed to study and to compare the photoreactions of CH₃I on TiO₂-B and Au/TiO₂-B and the effect of O₂. The presence of gold particles on TiO₂-B increases the efficiency of CH₃I photodegradation, forming adsorbed methoxy and formate. The role of gold is also discussed.     

Influence of deposition atmosphere on photocatalytic activity of TiO2/SiOx double-layers prepared by RF magnetron sputtering

TiO₂/SiO_x double-layers have been prepared at room temperature by RF magnetron sputtering. The TiO₂ top-layer was deposited in an Ar atmosphere, while the SiO_x bottom-layer was deposited in an Ar/O₂ atmosphere. Samples were characterized using X-ray photoelectron spectroscopy, scanning electron microscopy, atomic force microscopy, and photoluminescence techniques. The photocatalytic activity of the samples was evaluated by the photodegradation of methylene blue; the results showed that the photocatalytic activity of the TiO₂/SiO_x double-layers was superior to that of the TiO₂ single-layers. The presence of the SiO_x bottom-layer improved the photocatalytic activity of the TiO₂ layer because it may act as a trap for electrons generated in the TiO₂ layer thus preventing electron-hole recombinations.     

The correlation between structure and magnetism of Ni-implanted TiO2 annealed at different temperatures

In this paper, the structural and magnetic properties of Ni metal implanted TiO₂ single crystals are discussed. Ni nanocrystals (NCs) have been formed in TiO₂ after ion implantation. Their crystallite sizes increased with increasing post-annealing temperature. Metallic Ni nanocrystals inside the TiO₂ matrix are stable up to an annealing temperature of 1073 K. The Ni NCs formed inside TiO₂ make the major contribution to the measured ferromagnetism.     

V+注入锐钛矿TiO2第一性原理研究

用金属离子注入方法在锐钛矿TiO₂薄膜中掺杂了V⁺，采用全势线性缀加平面波方法计算了锐钛矿TiO₂及V⁺掺杂TiO₂超原胞的电子结构，通过紫外-可见吸收光谱测试方法检测了注入不同剂量的V⁺对TiO₂薄膜吸收光谱的影响.理论计算和实验结果表明，锐钛矿TiO₂薄注入V⁺后，带隙宽度变小，吸收光谱发生红移，并且TiO 关键词： +注入')" href="#">V⁺注入 2')" href="#">TiO₂ 全势线性缀加平面波方法 能带结构     

Fabrication,characterization and biocompatibility of TiO2 nanotubes via anodization of Ti6Al7Nb

Ti6Al7Nb has been used as an implant material because of its good corrosion resistance and high mechanical properties. However, the presence of aluminium (Al), which may lead to ostemalacia, anaemia and nervous system disorders, limited its wide clinical use. In this study, a titanium oxide (TiO₂) nanoporous layer was fabricated on a Ti6Al7Nb alloy using an electrochemical anodic oxidation method. The structure of the TiO₂ nanoporous layer was examined by scanning electron microscopy. The chemical compositions of the samples were analysed by X-ray photoelectron spectroscopy (XPS). Biocompatibility was evaluated by culturing rat osteoblast cells. The result showed that TiO₂ nanoporous layers comprise a mixed oxide containing TiO₂ and a small amount of nobium oxides (Nb₂O₅) and almost no elemental aluminium. The outer layer of the TiO₂ nanoporous layer comprises highly ordered nanotubes and the inner layer forms disordered nanopores. The TiO₂ nanoporous layer could support the adhesion, proliferation, differentiation and gene expression of osteoblast cells. Therefore, a TiO₂ nanoporous layer could enhance the biocompatibility of Ti6Al7Nb alloy and is as a promising candidate for Ti6Al7Nb alloy implants.     

Thickness effect of the TiO2 nanofiber scattering layer on the performance of the TiO2 nanoparticle/TiO2 nanofiber-structured dye-sensitized solar cells

TiO₂ nanofibers (NFs) were fabricated by an electrospinning process and were used as scattering layers in dye-sensitized solar cells (DSSCs). The NF-coated photoanodes of the DSSCs were prepared with a variety of scattering layer thicknesses. The thickness effect of the scattering layer on the double-layered TiO₂ nanoparticle (NP)/TiO₂ NF structure was investigated through structural, morphological, and optical measurements. In the double-layered photoanode, the TiO₂ NP layer plays a major role in dye adsorption and light transmission, and the TiO₂ NF scattering layer improves the absorption of visible light due to the light scattering effects. The scattering effect of TiO₂ NFs layer was examined by the incident monochromatic photon-to-electron conversion efficiency (IPCE) and UV–Vis spectrometry. The conversion efficiency for the 12 μm-thick photoanode composed of a 2 μm-thick TiO₂ NF layer and 10 μm-thick TiO₂ NP layer was higher than that of DSSCs with only TiO₂ NPs photoanode by approximately 33%.