pH-Metric study of gamma-irradiated table sugar for dosimetry purpose

Table sugar has been studied for a long time as a dosimeter in radiation accident and in high-dose dosimetry by using different analytical techniques especially electron paramagnetic resonance (EPR) and optical absorption spectrometry (OA). In this work, we report the results obtained by pH-metry on gamma-irradiated sugar. Table sugar samples were exposed to gamma radiation with doses of 0.1–58 kGy. Aqueous solutions of sugar were prepared with different concentrations ranged from 1% to 60% (w/w). It was found that sugar solutions showed strong decrease of pH up to concentration of 10% (w/w) followed by a slow decrease for the concentrations between 10 and 60% (w/w). Two possible mechanisms are proposed to explain the acidity increasing of the sugar solutions based on the existence of a carbonyl radical induced by gamma irradiation in solid table sugar with an open ring structure. Results for radiation response, post-irradiation change, reading temperature, dose-rate effect and repeatability are presented in this study. The results showed that pH-metric/sugar solution is an adequate high-dose dosimetric system in the dose range of 0.1–10 kGy.     

Ultrasonic depolymerization of aqueous carboxymethylcellulose

Prolonged exposure of solutions of macromolecules to high-energy ultrasonic waves produces a permanent reduction in viscosity. However, the exact mechanism by which degradation occurs is still open to discussion. According to this study hydrodynamic forces played the primary role in degradation process. This study showed that there is an optimal carboxymethylcellulose (CMC) concentration to the most efficient degradation. Ultrasound degraded preferentially large CMC molecules and cleavage took place roughly at the centre of the CMC molecules. Degradation of CMC did not proceed below a certain molecular mass. During ultrasonic degradation the molecular mass distribution narrowed. For any polymer degradation process to become acceptable to industry, it is important to be able to specify the sonication conditions to produce a particular relative molecular mass distribution.     

用傅立叶变换红外光谱法研究核辐照对人参粉成分的影响

本文采用傅立叶变换红外光谱(吸收光谱、二阶导数谱及差谱)法对经不同剂量核辐照的人参粉进行了对比研究.辐照剂量不高于9 kGy时,人参粉样品的化学成分几乎没有发生变化;人参粉样品经15kGy及以上的辐照剂量辐照后,可能产生新的化学成分,表明采用辐照剂量不高于9 kGy的核辐照杀灭人参粉污染的微生物和各种寄生虫卵是可行的;...     

聚丙烯/抗老化剂复合体系的γ-射线辐照降解研究

研究了聚丙烯(PP)及含有受阻酚类抗氧剂和受阻胺类光稳定剂复合体系的PP复合物经过γ-射线辐照后发生的结构变化及抗老化剂所起作用。实验利用红外光谱(FTIR)和示差扫描量热法(DSC)对PP的结构变化进行了系统表征。研究结果表明,当辐照剂量较小(50 kGy)时,纯PP及其复合物体系均未发生明显降解;当辐照剂量较大(≥50 kGy)时,PP及其复合物的羰基指数迅速提高,二者的结晶温度和熔融温度大幅度降低,说明PP发生了严重降解。在相同γ-射线辐照剂量条件下(≥50 kGy),PP复合物的羰基指数高于纯PP,而结晶温度以及熔融温度低于纯PP,表明高辐照剂量下抗老化剂复合物的存在不但没有阻止聚丙烯的降解,反而加快了降解的速率。     

Effect of ultrasound on the immunogenic corn cob xylan

Changes in the structural, molecular and functional properties of the immunogenic corn cob xylan evoked by ultrasonication in water, 1% NaOH and 5% NaOH were investigated. The reduction of the high molar mass (MM) fraction was more intense than that of the medium MM fraction, depending on the sonic power, sonication time, and alkali concentration. The chain degradation was more effective in the alkaline media. The UV-absorbing component, accompanying the xylan polymers in the whole MM range, showed an accumulation in the high MM region as well as shiftening to higher sizes, particularly in 5% NaOH. The sugar composition and primary structure of the xylan was almost retained under all irradiation conditions studied. Although the biological activity of the xylan was affected by the ultrasound, no significant decrease of the biological response was found at short irradiation time and low sonic power.     

Ultrasound irradiation alters the spatial structure and improves the antioxidant activity of the yellow tea polysaccharide

In this study, the impact of ultrasound irradiation on the structural characteristics and antioxidant properties of yellow tea polysaccharides with different molecular weights (Mw) were investigated. Native yellow tea polysaccharide containing YTPS-3N, YTPS-5N and YTPS-7N were prepared through precipitation with ethanol at various concentrations of 30%, 50%, and 70%, respectively, and irradiated with high intensity ultrasound (20 kHz) for 55 min to yield yellow tea polysaccharide including YTPS-3U, YTPS-5U and YTPS-7U. The molecular weight (Mw) of YTPS-3N (from 37.7 to 15.1 kDa) and YTPS-5N (from 14.6 to 5.2 kDa) sharply decreased upon ultrasound irradiation, coincidentally particle size (Zavg) was also significantly reduced for YTPS-3N (40%), YTPS-5N (48%) and YTPS-7N (54%). The high-performance liquid chromatography and Fourier transform-infrared spectroscopy analysis revealed a partial degradation of native yellow tea polysaccharide treated with ultrasound, though the monosaccharide composition was not altered. Furthermore, changes in morphology and the breakdown of native yellow tea polysaccharide upon irradiation was confirmed with the circular dichroism spectrum, atomic force and scanning electron microscopy. As a consequence, irradiation of yellow tea polysaccharide increased free radical scavenging activity with YTPS-7U exhibiting the highest levels of 2, 2-diphenyl-1-picrylhydrazyl free radical, superoxide and hydroxyl radicals scavenging activity. These results suggest that the alteration of the spatial structure of yellow tea polysaccharide can enhance its antioxidant activity which is an important property for functional foods or medicines.     

Photochemistry of refractive index structures in poly(methyl methacrylate) by femtosecond laser irradiation

Femtosecond, subablation threshold photomodification of poly(methyl methacrylate) (PMMA) at 387 nm is explored to enable fabrication of optical components. Volatile fragment analysis (thermal desorption gas chromatography-mass spectrometry) and molecular weight distribution monitoring (size exclusion chromatography) suggest photochemical modification, involving direct cleavage of the polymer backbone and propagation via chain unzipping under formation of monomers, similar to the pyrolytic degradation of PMMA. Waveguides were produced in undoped, clinical-grade PMMA, showing an increased refractive index in the laser focal region (Dnmax=4x10(-3)).     

The effect of ultrasound on the structure and properties of the water-soluble corn hull heteroxylan

Ultrasonic irradiation of a water-soluble corn hull xylan fraction in neutral and alkaline aqueous medium has been found to produce significant changes in its molecular properties. Degradation is first manifested by a decrease in the large molar mass component under generation of polymer chains with about the same size as those of the main molar mass component. The latter is slightly shifted to the lower molar mass region only at stronger irradiation conditions. Ultrasonication of the xylan in neutral aqueous medium at high ultrasound power and/or long irradiation caused no significant changes in its sugar composition, primary structure and viscoelastic properties.     

Influence of electron irradiation on properties of semi-insulating GaAs detectors

The effects of electron beam irradiation on electrical and spectrometric properties of semi-insulating (SI) GaAs detectors were studied. The electric properties were monitored by reverse and forward current–voltage characteristics. In general, a breakdown voltage decrease with the dose was observed. However, some samples showed a local increase in the breakdown voltage at doses between 5 and 10?kGy. The detector spectrometric properties (the charge collection efficiency (CCE), the energy resolution and the detection efficiency) were evaluated from measured spectra of the ²⁴¹Am radionuclide gamma source before and after electron irradiation. The CCE and energy resolution showed minor changes after irradiation. The detection efficiency noticed an initial increase (up to a dose of 5?kGy) followed by a permanent decrease. At 30?kGy, the overall degradation of detector functionality was observed with all samples.     

X-ray irradiation-induced structural modifications in PM-355 polymeric nuclear track detector film

Samples from sheets of the polymeric material PM-355 have been exposed to X-rays from a 50 kV X-ray tube in the dose range of 10–300 kGy. The resultant effect of X-ray irradiation on the structural properties of PM-355 has been investigated using different techniques such as X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, Vickers hardness and refractive index measurements. The results indicate that the X-ray irradiation of PM-355 in the dose range of 10–20 kGy causes initially chain scission. Above 20 and up to 100 kGy, the active free radicals produced from scission contribute to chemical reactions that lead to the crosslinking. Thus, the X-ray irradiation in the dose range of 20–100 kGy leads to a more compact structure of the PM-355 polymer, resulting in an enhancement of its Vickers hardness and refractive index. Moreover, the irradiation in the dose range of 100–300 kGy leads to the predominance of the degradation. This degradation is reported by FTIR spectroscopy and enhances the degree of ordering in the degraded samples as revealed by XRD technique. Additionally, it decreases both the Vickers hardness and refractive index of the PM-355 samples.     

原位漫反射红外光谱研究升温速率对HMX炸药热分解过程的影响

原位红外光谱法是一种新兴的动态研究方法。该方法具有原位实时监控和红外光谱精确分析物质化学结构的优点,能够实时跟踪材料在不同温度下的化学变化,测定材料的微观结构与温度的关系。采用原位漫反射红外光谱研究了炸药1,3,5,7-四硝基-1,3,5,7-四氮杂环辛烷(HMX)分别在每min 5, 10, 20和40 ℃四种不同升温速率下的热分解行为。研究结果表明：在5 ℃·min-1升温速率下,断裂的HMX环发生分子内结合,在10, 20和40 ℃·min-1升温速率下,断裂的HMX发生分子间成环,形成稳定的八元环结构。随着温度的升高,C—N键的断裂数率远高于N—N键的断裂速率。随着升温速率的增加,C—N键的起始分解温度增加,表明增加升温速率会引起HMX分解的滞后。检测到HMX的分解所释放出CO₂, N₂O, CO, NO, HCHO, HONO, NO₂和HCN共八种气体,升温速率的变化未改变HMX的分解机理。     

Ultrasound-assisted limited enzymatic hydrolysis of high concentrated soy protein isolate: Alterations on the functional properties and its relation with hydrophobicity and molecular weight

The effects of power ultrasound (US) pretreatment on the preparation of soy protein isolate hydrolysate (SPIH) prepared at the same degree of hydrolysis (DH) of 12 % were measured. Cylindrical power ultrasound was modified into mono-frequency (20, 28, 35, 40, 50 kHz) ultrasonic cup coupled with an agitator to make it applicable for high density SPI (soy protein isolate) solutions (14 %, w/v). A comparative study of the alterations of the hydrolysates molecular weight, hydrophobics, antioxidants and functional properties change as well as their relation were explored. The results showed that under the same DH, ultrasound pretreatment decelerated the degradation of protein molecular mass and the decrease rate of the degradation lessened with the increase of ultrasonic frequency. Meanwhile, the pretreatments improved the hydrophobics and antioxidants properties of SPIH. Both surface hydrophobicity (H₀) and relative hydrophobicity (RH) of the pretreated groups increased with the decrease of ultrasonic frequency. Lowest frequency (20 kHz) ultrasound pretreatment had the most improved emulsifying properties and water holding capacities, although decrease in the viscosity and solubility were found. Most of these alterations were correspondence toward the change in hydrophobics properties and molecular mass. In conclusion, the frequency selection of ultrasound pretreatment is essential for the alteration of SPIH functional qualities prepared at the same DH.     

Increased porous morphology and thermal degradation of electron beam-irradiated PVDF-HFP/LiCLO4 polymer electrolyte

The effect of 8?MeV energy electron beam radiation at 40, 80 and 120?kGy dosage on surface morphology and thermal properties of lithium perchlorate-doped poly (vinylidene fluoride-co-hexafluoropropylene) polymer electrolyte films have been studied. The field emission scanning electron microscopic image shows small-porous structured morphology for unirradiated film, but it changed drastically into large and deep porous structure as well as the size of spherulites is reduced for 120?kGy confirming the influence of irradiation on morphology. The atomic force microscope reveals the significantly changed surface roughness of unirradiated film from 116.8 to 123.4?nm with a hill-like pattern morphology for 120?kGy confirming the increased amorphousity after irradiation. The thermal study confirmed that the decrease in the melting point of unirradiated film 160.86–155.24°C for 120?kGy doses is attributed to the formation of defects by the chain scissioning process resulting in the degradation of polymer electrolytes at high dose.     

Radiation-induced thermoluminescence characteristics of feldspar upon different heat and microwave treatments

Feldspar minerals are well-known markers for thermoluminescence (TL)-based identification of irradiated foodstuff because of their high TL sensitivity and characteristic TL glow curves. Post-irradiation processing, particularly heating, may affect luminescence properties. In the present study, the effect of boiling, roasting, and microwave treatments on TL properties of irradiated (0, 5, and 10 kGy) feldspar was investigated. The TL glow peak faded (TL peak maxima shift towards higher temperature) upon boiling or roasting, which was mainly dependent upon treatment temperature and time. This effect was most apparent in the roasted samples. Liquid samples showed more changes in TL characteristics than solid samples upon microwave treatment; however, the effect was less prominent compared to those of roasting and boiling. TL ratios could not confirm the TL results when boiled and roasted samples were treated at ≥100 °C, whereas the microwave treatment showed a negligible effect on the TL ratio.     

Modification induced by gamma irradiation in Bayfol CR 1-4 polycarbonate

Bayfol CR 1-4 polycarbonate is a class of polymeric solid state nuclear track detector which has many applications in various radiation detection fields. Samples from sheets of Bayfol have been irradiated with gamma doses ranging from 100 to 620 kGy. The structural modifications in the gamma-irradiated Bayfol samples have been studied as a function of dose, using different characterization techniques such as X-ray diffraction (XRD), Fourier-transform infrared (FTIR) spectroscopy, intrinsic viscosity and refractive index. The results indicate that the carbonyl group (C?O) degraded under irradiation up to 200 kGy. This degradation, reported by FTIR spectroscopy enhanced the degree of ordering in the degraded samples as revealed by the XRD technique. Above 200 and up to 620 kGy, cross-linking is achieved, leading to an increase in the intrinsic viscosity from 0.41 to 0.78 at 35°C, indicating an increase in the average molecular mass. On the other hand, the resultant effect of gamma irradiation on the thermal properties of Bayfol has been investigated using thermo-gravimetric analysis, results indicating that the gamma irradiation in the dose range 200–620 kGy led to a more compact structure of Bayfol polymer, which resulted in an improvement in its thermal stability with an increase in the activation energy of thermal decomposition due to cross-linking. In addition, the V–I characteristics of the polymer samples were performed, results indicated that at higher voltage, the conduction mechanism of Bayfol CR 1-4 was identified as the Poole–Frenkel type.     

微波加热自组装成环荧光显微成像技术在环境水样中的应用研究

提出了一种基于溶剂毛细流效应的微波加热自组装成环荧光显微成像技术在环境水样中的应用方法。在pH 4.58的HAc-NaAc 反应介质和聚乙烯醇-124存在下,盐酸小檗碱液滴在疏水性玻璃表面上受热挥发形成直径为1.1 mm,环带宽为19.2 μm自组装环(self-ordered ring, SOR), 其荧光被苦味酸猝灭,猝灭强度与苦味酸的浓度成正比。当点样体积为0.1 μL时,线性范围为1.3～30.0×10-7 mol·L-1,方法的检测限为1.3×10-8 mol·L-1。应用于天然水样及合成水样分析,回收率为96.3％～108.0％,RSD小于3.3％。该方法灵敏度比斑点分析提高50倍,比液相分析方法提高了60倍,且来源于背景的干扰大大降低。检测方法在环境、生化等领域具有广泛的实用性和优越性。     

EPR study of table sugar rod and powder as high dose dosimeters

In order to improve the ease of sample handling, the reproducibility of signal detection and quantification, simple methods of incorporating a homogeneous mixture containing sugar powder (30%) with wax (35%) and rubber (35%) into rods has been adopted. The dose response, the time stability of the free radicals produced in table sugar dosimeters (in both rod and powder form) by gamma radiation and the effect of the temperature during irradiation were studied by EPR (Electron Paramagnetic Resonance). The peak-to-peak height (PPH) measurement of the EPR signal is studied as a function of the absorbed gamma dose in the range 0.1–58 kGy. For the two forms, a linear dependency is found between 0.1 and 26 kGy. At higher doses the EPR signal amplitude continues to grow but non-linear up to 58 kGy. The dependence of temperature during irradiation has been investigated in the temperature range 25–40 °C and the calculated correction coefficients were found (2.7 ± 0.2)% °C^?1 and (1.5 ± 0.3)% °C^?1, respectively, for powder and rod forms. The time stability of the stored sugar samples was investigated for 34 days at room temperature, a rapid decrease of EPR signal was showed immediately after irradiation followed by slowly decrease.     

Research on pyrolysis of toluene under microwave heating by using ReaxFF molecular dynamics simulations

ReaxFF molecular dynamics (MD) simulations are performed to study high-temperature pyrolysis of toluene under microwave heating. It is observed that the temperature of the reaction system under microwave heating has a rapidly rising stage, which is similar to the phenomenon of thermal runaway often appeared in reactions under microwave heating. Simulations indicate that the consumption rate of toluene and generating rates of H₂ and CH₄ obtained under microwave heating are always lower than those obtained under conventional heating at the early stage. Analyses of the pyrolysis of toluene show that ReaxFF MD simulations can provide an efficient way to study chemical reactions under microwave heating.     

一种微波加热装置的风冷散热研究

微波加热装置工作过程会散发大量的热量,如果不能及时排出,会造成输出功率的下降.本文以九个磁控管加热单元组成的微波加热装置为研究对象,首先提出一种风冷散热结构设计,接着通过Fluent热仿真软件验证结构设计的合理性,然后通过对比分析加热装置进风口位置、面积大小等因素对散热效果的影响,对散热结构进行改进,进一步提高了内部磁...     

Interferometric investigation of the effect of gamma radiation on the refractive index of CR-39 polymer

A non-contact and simple interferometric technique has been used to measure the refractive index variation of gamma irradiated CR-39 polymer samples. Six samples of thickness (750 μm) and dimensions of 1.5 × 3 cm², have been irradiated with gamma radiation doses in the range from zero to 600 kGy. It is observed that the refractive index increases by increasing the dose and reaches its maximum value at 40 kGy dose, and then starts to decrease again. This means that the gamma radiation deformation in the CR-39 polymer is a chain scission effect. This interferometric technique could make a contribution to recombination and degradation mechanisms on CR-39 polymer.