具有L型源极场板的双槽绝缘体上硅高压器件新结构

为了提高小尺寸绝缘体上硅(SOI)器件的击穿电压,同时降低器件比导通电阻,提出了一种具有L型源极场板的双槽SOI高压器件新结构.该结构具有如下特征:首先,采用了槽栅结构,使电流纵向传导面积加宽,降低了器件的比导通电阻;其次,在漂移区引入了Si O2槽型介质层,该介质层的高电场使器件的击穿电压显著提高;第三,在槽型介质层中引入了L型源极场板,该场板调制了漂移区电场,使优化漂移区掺杂浓度大幅增加,降低了器件的比导通电阻.二维数值仿真结果表明:与传统SOI结构相比,在相同器件尺寸时,新结构的击穿电压提高了151%,比导通电阻降低了20%;在相同击穿电压时,比导通电阻降低了80%.与相同器件尺寸的双槽SOI结构相比,新结构保持了双槽SOI结构的高击穿电压特性,同时,比导通电阻降低了26%.     

漂移区表面阶梯掺杂LDMOS的击穿电压模型

提出表面阶梯掺杂(SD：Step Doping on surface)LDMOS的二维击穿电压模型.基于求解多区二维Poisson方程,获得SD结构表面电场的解析式.借助此模型,研究其结构参数对击穿电压的影响;计算优化漂移区浓度和厚度与结构参数的关系,给出获得最大击穿电压的途径.数值结果,解析结果和试验结果符合较好.漂移区各区和衬底电场相互调制,在漂移区中部产生新的峰值,改善电场分布;高掺杂区位于表面,降低了正向导通电阻.结果表明：SD结构较常规结构击穿电压从192V提高到242V,导通电阻下降33%. 关键词： 阶梯掺杂 模型 优化 调制     

New CMOS compatible super junction LDMOST with n-type buried layer

A new super-junction lateral double diffused MOSFET (LDMOST) structure is designed with n-type charge compensation layer embedded in the p$^{ - }$-substrate near the drain to suppress substrate-assisted depletion effect that results from the compensating charges imbalance between the pillars in the n-type buried layer. A high electric field peak is introduced in the surface by the pn junction between the p$^{ - }$-substrate and n-type buried layer, which given rise to a more uniform surface electric field distribution by modulation effect. The effect of reduced bulk field (REBULF) is introduced to improve the vertical breakdown voltage by reducing the high bulk electric field around the drain. The new structure features high breakdown voltage, low on-resistance and charges balance in the drift region due to n-type buried layer.     

具有部分超结的新型SiC SBD特性分析

提出了一种具有部分超结（super junction, SJ）结构的新型SiC肖特基二极管,命名为SiC Semi-SJ-SBD结构,通过将常规SBD耐压区分为常规耐压区和超结耐压区来减小导通电阻,改善正向特性.利用二维器件模拟软件MEDICI仿真分析,研究了不同超结深度和厚度时击穿电压(V_B)和比导通电阻(R_on-sp),与常规结构的SBD比较得出,半超结结构可以明显改善SiC肖特基二极管特性,并得到优化的设计方案,选择超结宽度2< 关键词： SiC肖特基二极管 super junction 导通电阻 击穿电压     

A super junction SiGe low-loss fast switching power diode

This paper proposes a novel super junction (SJ) SiGe switching power diode which has a columnar structure of alternating p^- and n^- doped pillar substituting conventional n^- base region and has far thinner strained SiGe p⁺ layer to overcome the drawbacks of existing Si switching power diode. The SJ SiGe diode can achieve low specific on-resistance, high breakdown voltages and fast switching speed. The results indicate that the forward voltage drop of SJ SiGe diode is much lower than that of conventional Si power diode when the operating current densities do not exceed 1000 A/cm², which is very good for getting lower operating loss. The forward voltage drop of the Si diode is 0.66V whereas that of the SJ SiGe diode is only 0.52 V at operating current density of 10 A/cm². The breakdown voltages are 203 V for the former and 235 V for the latter. Compared with the conventional Si power diode, the reverse recovery time of SJ SiGe diode with 20 per cent Ge content is shortened by above a half and the peak reverse current is reduced by over 15%. The SJ SiGe diode can remarkably improve the characteristics of power diode by combining the merits of both SJ structure and SiGe material.     

Control of electric field in 4H-SiC UMOSFET: Physical investigation

In this paper, we show how breakdown voltage (V_BR) and the specific on-resistance (R_on) can be improved simply by controlling of the electric field in a power 4H-SiC UMOSFET. The key idea in this work is increasing the uniformity of the electric field profile by inserting a region with a graded doping density (GD region) in the drift region. The doping density of inserted region is decreased gradually from top to bottom, called Graded Doping Region UMOSFET (GDR-UMOSFET). The GD region results in a more uniform electric field profile in comparison with a conventional UMOSFET (C-UMOSFET) and a UMOSFET with an accumulation layer (AL-UMOSFET). This in turn improves breakdown voltage. Using two-dimensional two-carrier simulation, we demonstrate that the GDR-UMOSFET shows higher breakdown voltage and lower specific on-resistance. Our results show the maximum breakdown voltage of 1340 V is obtained for the GDR-UMOSFET with 10 µm drift region length, while at the same drift region length and approximated doping density, the maximum breakdown voltages of the C-UMOSFET and the AL-UMOSFET structures are 534 V and 703 V, respectively.     

An oxide filled extended trench gate super junction MOSFET structure

This paper proposes an oxide filled extended trench gate super junction (SJ) MOSFET structure to meet the need of higher frequency power switches application. Compared with the conventional trench gate SJ MOSFET, new structure has the smaller input and output capacitances, and the remarkable improvements in the breakdown voltage, on-resistance and switching speed. Furthermore, the SJ in the new structure can be realized by the existing trench etching and shallow angle implantation, which offers more freedom to SJ MOSFET device design and fabrication.     

Ultra-low on-resistance high voltage (>600 V) SOI MOSFET with a reduced cell pitch

A low specific on-resistance (R S,on) silicon-on-insulator (SOI) trench MOSFET (metal-oxide-semiconductor-field-effect-transistor) with a reduced cell pitch is proposed.The lateral MOSFET features multiple trenches:two oxide trenches in the drift region and a trench gate extended to the buried oxide (BOX) (SOI MT MOSFET).Firstly,the oxide trenches increase the average electric field strength along the x direction due to lower permittivity of oxide compared with that of Si;secondly,the oxide trenches cause multiple-directional depletion,which improves the electric field distribution and enhances the reduced surface field (RESURF) effect in the SOI layer.Both of them result in a high breakdown voltage (BV).Thirdly,the oxide trenches cause the drift region to be folded in the vertical direction,leading to a shortened cell pitch and a reduced R S,on.Fourthly,the trench gate extended to the BOX further reduces R S,on,owing to the electron accumulation layer.The BV of the MT MOSFET increases from 309 V for a conventional SOI lateral double diffused metal-oxide semiconductor (LDMOS) to 632 V at the same half cell pitch of 21.5 μm,and R S,on decreases from 419 m · cm 2 to 36.6 m · cm 2.The proposed structure can also help to dramatically reduce the cell pitch at the same breakdown voltage.     

高k介质电导增强SOI LDMOS机理与优化设计

本文提出一种高k介质电导增强SOI LDMOS新结构（HK CE SOI LDMOS）,并研究其机理. HK CE SOI LDMOS的特征是在漂移区两侧引入高k介质,反向阻断时,高k介质对漂移区进行自适应辅助耗尽,实现漂移区三维RESURF效应并调制电场,因而提高器件耐压和漂移区浓度并降低导通电阻. 借助三维仿真研究耐压、比导通电阻与器件结构参数之间的关系. 结果表明,HK CE SOI LDMOS与常规超结SOI LDMOS相比,耐压提高16%–18%,同时比导通电阻降低13%–20%,且缓解了由衬底辅助耗尽效应带来的电荷非平衡问题. 关键词： k介质')" href="#">高k介质 绝缘体上硅 (SOI) 击穿电压 比导通电阻     

具有半绝缘多晶硅完全三维超结横向功率器件

为了突破传统LDMOS (lateral double-diffused MOSFET)器件击穿电压与比导通电阻的硅极限的2.5 次方关系, 降低LDMOS器件的功率损耗, 提高功率集成电路的功率驱动能力, 提出了一种具有半绝缘多晶硅SIPOS (semi-insulating poly silicon)覆盖的完全3 D-RESURF (three-dimensional reduced surface field)新型Super Junction-LDMOS结构(SIPOS SJ-LDMOS). 这种结构利用SIPOS的电场调制作用使SJ-LDMOS的表面电场分布均匀, 将器件单位长度的耐压量提高到19.4 V/μupm; 覆盖于漂移区表面的SIPOS使SJ-LDMOS沿三维方向均受到电场调制, 实现了LDMOS的完全3 D-RESURF效应, 使更高浓度的漂移区完全耗尽而达到高的击穿电压; 当器件开态工作时, 覆盖于薄场氧化层表面的SIPOS的电场作用使SJ-LDMOS的漂移区表面形成多数载流子积累, 器件比导通电阻降低. 利用器件仿真软件ISE分析获得, 当SIPOS SJ-LDMOS的击穿电压为388 V时, 比导通电阻为20.87 mΩ·cm², 相同结构参数条件下, N-buffer SJ-LDMOS的击穿电压为287 V, 比导通电阻为31.14 mΩ·cm²; 一般SJ-LDMOS 的击穿电压仅为180 V, 比导通电阻为71.82 mΩ·cm².     

具有P型覆盖层新型超级结横向双扩散功率器件

为了设计功率集成电路所需要的低功耗横向双扩散金属氧化物半导体器件(lateral double-diffused MOSFET), 在已有的N型缓冲层超级结LDMOS(N-buffered-SJ-LDMOS)结构基础上, 提出了一种具有P型覆盖层新型超级结LDMOS结构(P-covered-SJ-LDMOS). 这种结构不但能够消除传统的N沟道SJ-LDMOS由于P型衬底产生的衬底辅助耗尽问题, 使得超级结层的N区和P区的电荷完全补偿, 而且还能利用覆盖层的电荷补偿作用, 提高N型缓冲层浓度, 从而降低了器件的比导通电阻. 利用三维仿真软件ISE分析表明, 在漂移区长度均为10 μm的情况下, P-covered-SJ-LDMOS的比导通电阻较一般SJ-LDMOS结构降低了59%左右, 较文献提出的N型缓冲层 SJ-LDMOS(N-buffered-SJ-LDMOS)结构降低了43%左右.     

新型缓冲层分区电场调制横向双扩散超结功率器件

为了突破传统横向双扩散金属-氧化物-半导体器件(lateral double-diffused MOSFET)击穿电压与比导通电阻的极限关系,本文在缓冲层横向双扩散超结功率器件(super junction LDMOS-SJ LDMOS)结构基础上,提出了具有缓冲层分区新型SJ-LDMOS结构.新结构利用电场调制效应将分区缓冲层产生的电场峰引入超结(super junction)表面而优化了SJ-LDMOS的表面电场分布,缓解了横向LDMOS器件由于受纵向电场影响使横向电场分布不均匀、横向单位耐压量低的问题.利用仿真分析软件ISE分析表明,优化条件下,当缓冲层分区为3时,提出的缓冲层分区SJ-LDMOS表面电场最优,击穿电压达到饱和时较一般LDMOS结构提高了50%左右,较缓冲层SJ-LDMOS结构提高了32%左右,横向单位耐压量达到18.48 V/μm.击穿电压为382 V的缓冲层分区SJ-LDMOS,比导通电阻为25.6 mΩ·cm2,突破了一般LDMOS击穿电压为254 V时比导通电阻为71.8 mΩ·cm2的极限关系.     

New Power Lateral Double Diffused Metal-Oxide-Semiconductor Transistor with a Folded Accumulation Layer

A new lateral double diffused metal oxide semiconductor field effect transistor with a double-charge accumulation layer using a folded silicon substrate is proposed to improve the performance of the breakdown voltage and specific on-resistance. Three kinds of technologies, which are the additional electric field modulation effect, majority carrier accumulation and increasing the effective conduction area, are applied simultaneously by a semi- insulating polycrystalline silicon layer deposited over the top of thin oxide covering the drift region. It is indicated that by the simulator, the ideal silicon limits of the breakdown voltage and specific on-resistance have been broken due to the complete three-dimensional reduced surface field effect and the doubled majority carrier accumulation layer.     

Study and optimal simulation of 4H-SiC floating junction Schottky barrier diodes’ structures and electric properties

This paper stuides the structures of 4H-SiC floating junction Schottky barrier diodes. Some structure parameters of devices are optimized with commercial simulator based on forward and reverse electrical characteristics. Compared with conventional power Schottky barrier diodes, the devices are featured by highly doped drift region and embedded floating junction layers, which can ensure high breakdown voltage while keeping lower specific on-state resistance, and solve the contradiction between forward voltage drop and breakdown voltage. The simulation results show that with optimized structure parameter, the breakdown voltage can reach 4.36 kV and the specific on-resistance is 5.8 mΩ·cm2 when the Baliga figure of merit value of 13.1 GW/cm2 is achieved.     

Novel high-voltage power lateral MOSFET with adaptive buried electrodes

A new high-voltage and low-specific on-resistance (R on,sp ) adaptive buried electrode (ABE) silicon-on-insulator (SOI) power lateral MOSFET and its analytical model of the electric fields are proposed. The MOSFET features are that the electrodes are in the buried oxide (BOX) layer, the negative drain voltage V d is divided into many partial voltages and the output to the electrodes is in the buried oxide layer and the potentials on the electrodes change linearly from the drain to the source. Because the interface silicon layer potentials are lower than the neighboring electrode potentials, the electronic potential wells are formed above the electrode regions, and the hole potential wells are formed in the spacing of two neighbouring electrode regions. The interface hole concentration is much higher than the electron concentration through designing the buried layer electrode potentials. Based on the interface charge enhanced dielectric layer field theory, the electric field strength in the buried layer is enhanced. The vertical electric field E I and the breakdown voltage (BV) of ABE SOI are 545 V/μm and -587 V in the 50 μm long drift region and the 1 μm thick dielectric layer, and a low R on,sp is obtained. Furthermore, the structure also alleviates the self-heating effect (SHE). The analytical model matches the simulation results.     

Analytical models of lateral power devices with arbitrary vertical doping profiles in the drift region

By solving the 2D Poisson's equation, analytical models are proposed to calculate the surface potential and electric field distributions of lateral power devices with arbitrary vertical doping profiles. The vertical and the lateral breakdown voltages are formulized to quantify the breakdown characteristic in completely-depleted and partially-depleted cases. A new reduced surface field (RESURF) criterion which can be used in various drift doping profiles is further derived for obtaining the optimal trade-off between the breakdown voltage and the on-resistance. Based on these models and the numerical simulation, the electric field modulation mechanism and the breakdown characteristics of lateral power devices are investigated in detail for the uniform, linear, Gaussian, and some discrete doping profiles along the vertical direction in the drift region. Then, the mentioned vertical doping profiles of these devices with the same geometric parameters are optimized, and the results show that the optimal breakdown voltages and the effective drift doping concentrations of these devices are identical, which are equal to those of the uniform-doped device, respectively. The analytical results of these proposed models are in good agreement with the numerical results and the previous experimental results, confirming the validity of the models presented here.     

Breakdown voltage model and structure realization of a thin silicon layer with linear variable doping on a silicon on insulator high voltage device with multiple step field plates

Based on the theoretical and experimental investigation of a thin silicon layer(TSL) with linear variable doping(LVD) and further research on the TSL LVD with a multiple step field plate(MSFP),a breakdown voltage(BV) model is proposed and experimentally verified in this paper.With the two-dimensional Poisson equation of the silicon on insulator(SOI) device,the lateral electric field in drift region of the thin silicon layer is assumed to be constant.For the SOI device with LVD in the thin silicon layer,the dependence of the BV on impurity concentration under the drain is investigated by an enhanced dielectric layer field(ENDIF),from which the reduced surface field(RESURF) condition is deduced.The drain in the centre of the device has a good self-isolation effect,but the problem of the high voltage interconnection(HVI) line will become serious.The two step field plates including the source field plate and gate field plate can be adopted to shield the HVI adverse effect on the device.Based on this model,the TSL LVD SOI n-channel lateral double-diffused MOSFET(nLDMOS) with MSFP is realized.The experimental breakdown voltage(BV) and specific on-resistance(R on,sp) of the TSL LVD SOI device are 694 V and 21.3 ·mm 2 with a drift region length of 60 μm,buried oxide layer of 3 μm,and silicon layer of 0.15 μm,respectively.     

Design optimization of high breakdown voltage vertical GaN junction barrier Schottky diode with high-K/low-K compound dielectric structure

A vertical junction barrier Schottky diode with a high-$K$/low-$K$ compound dielectric structure is proposed and optimized to achieve a high breakdown voltage (BV). There is a discontinuity of the electric field at the interface of high-$K$ and low-$K$ layers due to the different dielectric constants of high-$K$ and low-$K$ dielectric layers. A new electric field peak is introduced in the n-type drift region of junction barrier Schottky diode (JBS), so the distribution of electric field in JBS becomes more uniform. At the same time, the effect of electric-power line concentration at the p-n junction interface is suppressed due to the effects of the high-$K$ dielectric layer and an enhancement of breakdown voltage can be achieved. Numerical simulations demonstrate that GaN JBS with a specific on-resistance ($R_{\rm on, sp}$) of 2.07 m$\Omega\cdot$cm$^{2}$ and a BV of 4171 V which is 167% higher than the breakdown voltage of the common structure, resulting in a high figure-of-merit (FOM) of 8.6 GW/cm$^{2}$, and a low turn-on voltage of 0.6 V.     

阶梯氧化层新型折叠硅横向双扩散功率器件

为了设计功率集成电路所需的低功耗横向功率器件, 提出了一种具有阶梯氧化层折叠硅横向双扩散金属-氧化物-半导体(step oxide folding LDMOS, SOFLDMOS)新结构. 这种结构将阶梯氧化层覆盖在具有周期分布的折叠硅表面, 利用阶梯氧化层的电场调制效应, 通过在表面电场分布中引入新的电场峰而使表面电场分布均匀, 提高了器件的耐压范围, 解决了文献提出的折叠积累型横向双扩散金属-氧化物-半导体器件击穿电压受限的问题. 通过三维仿真软件ISE分析获得, SOFLDMOS 结构打破了硅的极限关系, 充分利用了电场调制效应、多数载流子积累和硅表面导电区倍增效应, 漏极饱和电流比一般LDMOS 提高3.4倍左右, 可以在62 V左右的反向击穿电压条件下, 获得0.74 mΩ·cm²超低的比导通电阻, 远低于传统LDMOS相同击穿电压下2.0 mΩ·cm²比导通电阻, 为实现低压功率集成电路对低功耗横向功率器件的要求提供了一种可选的方案.     

Comprehensive study of a 4H–SiC MES–MOSFET

In this paper, we studied the enhancement of the breakdown voltage in the 4H–SiC MESFET–MOSFET (MES–MOSFET) structure which we have proposed in our previous work. We compared this structure with Conventional Bulk-MOSFET (CB-MOSFET) and Field plated Conventional Bulk-MOSFET (FCB-MOSFET) structures. The 4H–SiC MES–MOSFET structure consists of two additional schottky buried gates which behave like a Metal on Semiconductor (MES) at the interface of the active region and substrate. The motivation for this structure was to enhance the breakdown voltage by introducing a new technique of utilizing the reduced surface field (RESURF) concept. In our comparison and investigation we used a two-dimensional device simulator. Our simulation results show that the breakdown voltage of the proposed structure is 3.7 and 2.9 times larger than CB-MOSFET and FCB-MOSFET structures, respectively. We also showed that the threshold voltage and the slope of drain current (I_D) as a function of drain–source voltage (V_DS) for all the structures is the same.