Metal-Support Interaction and Catalysis of the Catalysts Prepared Using Microemulsion

We have developed a new preparation method (ME method) of supported metal catalysts by using microemulsion. The metal particles in the catalyst prepared by this method were interacted strongly with support and were considered to be positively charged, and the SiO₂-supported Rh and Fe catalysts prepared by this method exhibited a unique activity and a good selectivity to oxygenates in the hydrogenation of CO. The Al₂O₃-supported Ni catalyst also exhibited an excellent activity and a strong resistance to carbon deposition in the methane-steam reforming. In this review, these interesting catalytic behaviors of the catalysts prepared by ME method were elucidated from the view-point of the electronic state of metals.     

Disilane Cleavage with Selected Alkali and Alkaline Earth Metal Salts

The industry-scale production of methylchloromonosilanes in the Müller–Rochow Direct Process is accompanied by the formation of a residue, the direct process residue (DPR), comprised of disilanes Me_nSi₂Cl_6-n (n=1–6). Great research efforts have been devoted to the recycling of these disilanes into monosilanes to allow reintroduction into the siloxane production chain. In this work, disilane cleavage by using alkali and alkaline earth metal salts is reported. The reaction with metal hydrides, in particular lithium hydride (LiH), leads to efficient reduction of chlorine containing disilanes but also induces disproportionation into mono- and oligosilanes. Alkali and alkaline earth chlorides, formed in the course of the reduction, specifically induce disproportionation of highly chlorinated disilanes, whereas highly methylated disilanes (n>3) remain unreacted. Nearly quantitative DPR conversion into monosilanes was achieved by using concentrated HCl/ether solutions in the presence of lithium chloride.     

The Significant Role of the Atomic Surface Structure of Support in Strong Metal-Support Interaction

Supported metal catalysts are important in many industrial reactions. It is reported that support materials are not always inert, and in some cases could even interact with metal nanoparticles (NPs) actively via various ways. In particular, the strong metal-support interaction (SMSI), referring to metal NPs covered by support materials, affects catalysis at the active sites on the metal NP surface, which can serve as a very effective method in tuning and improving catalytic performance. By tailoring the support materials or controlling the treatment processes, different kinds of SMSI, such as classical SMSI, oxidative SMSI, wet-chemistry SMSI, and adsorbate-mediated SMSI, can be achieved. This concept summarizes the general strategies to tune SMSI and discusses the key results. Moreover, a new proposal is presented to tailor SMSI by combining both the exposed facets of the support materials and external environments. Furthermore, the challenges faced at present are discussed and useful insights for future research concerning this topic are provided.     

Thermodynamic Properties of Ammonia Production from Hydrogenation of Alkali and Alkaline Earth Metal Amides

Thermodynamic properties of alkali and alkaline earth metal amides are critical for their performance in hydrogen storage as well as catalytic ammonia synthesis. In this work, the ammonia equilibrium concentrations of LiNH₂, KNH₂ and Ba(NH₂)₂ at ca.10 bar of hydrogen pressure and different temperatures were measured by using a high-pressure gas-solid reaction system equipped with a conductivity meter. Hydrogenation of KNH₂ gives the highest ammonia equilibrium concentration, followed by Ba(NH₂)₂ and LiNH₂. Based on these data, the entropy and enthalpy changes of the reaction of ANH₂+H₂→AH+NH₃ (A=Li, K, and Ba) were obtained from the van't Hoff equation. These thermodynamic parameters provide important information on the understanding of metal amides in catalytic ammonia synthesis reaction.     

The Thermal Degradation of Alkaline Earth Metal Salts of Poly(Itaconic Acid)

The Mg-, Ca- and Ba-salts of poly(itaconic acid) (PIA) were prepared by treating the aqueous solution of the polyacid with the corresponding metal oxide or hydroxide. The resulting polysalts were analysed by FTIR spectroscopy and thermogravimetry. The results indicate that the polysalts are thermally more stable than the parent PIA, they all degrade in a similar manner, the Ba-salt being the most stable. This revised version was published online in August 2006 with corrections to the Cover Date.     

阳离子交换色谱中色谱柱温度对碱金属与碱土金属离子保留的影响

研究了非抑制型阳离子交换色谱中色谱柱温度(25~50℃)对碱金属离子(Li+、Na+、K+、Rb+)和碱土金属离子(Mg2+、Ca2+、Sr2+)以及NH4+保留的影响。在Shim-pack IC-C1磺酸型阳离子交换柱上,以硝酸为流动相分离碱金属离子,以乙二胺或乙二胺-草酸(柠檬酸)为流动相分离碱土金属离子,随着色谱柱温度的升高,碱金属和碱土金属离子的保留时间均增长,其范特霍夫曲线具有良好的线性关系,斜率为负值,表明在此条件下碱金属和碱土金属离子的保留为吸热过程。在Shim-pack IC-SC1羧酸型阳离子交换柱上,以硫酸为流动相同时分离碱金属和碱土金属离子,随着色谱柱温度的升高,Mg2+、Ca2+的保留时间增长,而K+、Rb+的保留时间缩短,Li+、Na+、NH4+的保留时间基本不变。在此条件下,Mg2+、Ca2+、K+和Rb+的范特霍夫曲线具有良好的线性关系,其中Mg2+和Ca2+的曲线斜率为负值,K+和Rb+的曲线斜率为正值,表明Mg2+和Ca2+的保留表现为吸热过程,K+和Rb+的保留表现为放热过程。研究表明在不同固定相和流动相条件下,色谱柱温度对碱金属和碱土金属离子保留行为的影响不同。     

离子色谱法测定中药女贞子浸煮液中的碱金属和碱土金属

用离子色谱法测定了中药女贞子水浸煮液中K+、Na+、Ca2+、Mg2+的含量,色谱柱为IonPAC CS 12A(4 mm×250 mm)阳离子交换柱,淋洗液为11.0 mmol/L的硫酸溶液,流速1.00mL/min,电导检测器检测。结果表明,4种离子的检出限分别为:Na+0.021 mg/L,K+0.020 mg/L、Mg2+0.015 mg/L,Ca2+0.100 mg/L,相对标准偏差在0.72%~3.92%之间,回收率为98.3%~103.1%。结论:该法操作简便、快速,准确,为测定其它中药中Na+、K+、Mg2+、Ca2+的含量提供了一种有效的方法。     

碱土金属化合物在氧化锆上的分散与碱性

 研究了碱土金属化合物在ZrO2表面上的分散状况及碱性. 结果表明,碱土金属硝酸盐分解成为氧化物的难度随着原子序数的增大而增加. Mg(NO3)2在550 ℃时就可以直接分解为MgO. Ca(NO3)2和Sr(NO3)2不能单独分解成CaO和SrO, 但当负载在ZrO2载体上时,就可以在载体表面分解成CaO和SrO, 只是由于负载量不同其存在的形式各不相同. CaO含量较少时, CaO与ZrO2形成固溶体而不是以CaO的形式分散在ZrO2的表面; CaO含量较多时,生成CaZrO3. SrO含量较少时,以SrO的形式分散在ZrO2的表面上; 含量较多时,有SrZrO3生成. Ba(NO3)2即使有载体ZrO2存在时也不能分解成BaO, 而是以Ba(NO2)2的形式分散于ZrO2表面. CO2-TPD实验表明,与纯ZrO2相比,负载样品的碱位分布范围较宽,碱的强度与数量都有很大提高.     

Polymerization of Polar Monomers Using Cyclopentadienyl Complexes of the Alkaline Earth Metals

Tetramethylcyclopentadienyl complexes of magnesium, calcium and strontium are efficient catalysts at −78 °C for the solution polymerization of polar monomers such as alkyl methacrylates in the presence of only small amounts of triethylaluminium as cocatalyst. The molecular mass of the resulting polymers is predictable on the monomer/catalyst ratio. The polymerization reaction follows a first order kinetics with respect to the initial catalyst concentration. Block-copolymers are easily available by sequential dosage of the monomer. A living polymerization mechanism is proposed involving activation of the catalyst by alkylation and subsequent insertion of coordinated monomers.     

离子色谱法同时分析中药丹参中碱金属和碱土金属

用离子色谱法同时分析中药丹参中碱金属和碱土金属 ,结果表明 ,丹参中常见离子Li+ 、Na+ 、NH+4、K+ 、Mg2 + 、Ca2 + 含量比例各有不同。各离子的检出限为 0 .0 1～ 0 .0 3mg·L-1,线性范围分别为 0 .1～ 10 .0mg·L-1(Li+ 、NH+4)和 0 .2～ 5 0 .0mg·L-1(Na+ 、K+ 、Mg2 + 、Ca2 + )     

几种稀土盐封闭的铝阳极氧化试样的腐蚀行为

为提高铝硫酸阳极氧化膜的抗污染和防腐蚀性能，分别采用环境友好的铈盐、钇盐和镧盐溶液对阳极氧化膜进行了封闭处理。采用动电位极化法比较了不同稀土盐封闭的铝阳极氧化试样在弱酸性NaCl腐蚀介质中的电化学行为，采用扫描电子显微镜（SEM）和能量色散谱（EDS）对封闭试样腐蚀前后的表面形貌、组成进行了表征。结果表明：在腐蚀介质的侵蚀及强电化学极化条件下，铈盐和镧盐封闭的阳极氧化膜对铝基体具有较好的保护作用，而钇盐封闭膜的保护作用则较差。这种差别的主要原因是不同稀土盐封闭过程中封闭产物的析出倾向及速率不同。     

碱／碱土金属催化松木屑快速热解机制

研究碱／碱土金属（AAEM）对生物质的热解及其热解产物组成的影响规律,可为生物质热解特性研究和热解产物的高效利用提供重要的理论依据。本文以松木屑为原料,将原样进行酸洗,并对酸洗样分别用K、Ca、Na和Mg氯化盐溶液浸渍,在500℃和Ar气氛下对各样品进行快速热解,考察了4种金属离子对松木屑热解产物组成分布的影响规律;通过热重分析考察了各个样品的热解特性;通过对热解生物油的气相色谱／质谱（GC／MS）分析考察了快速热解的焦油成分。研究结果表明：AAEM对松木屑有明显的催化作用,AAEM的存在能够提高热解气体和固体的产率,降低热解焦油的产率;AAEM能够降低热解温度,使热解更加容易进行;快速热解的焦油成分主要有酚类、酮类、醛类、芳烃、醇类、脱水糖类、呋喃类以及酸类,AAEM显著影响焦油产物组成,特别是呋喃类和芳烃的含量会有所增加。本文为优化生物质的热解条件与提高热解生物油品质具有重要意义。     

多柔比星稀土金属离子配合物与DNA相互作用的研究

用紫外分光光度法和荧光光谱法研究了多柔比星( Adriamycin,ADM)稀土金属离子配合物(ADM-M)与DNA的相互作用.结果发现,在pH=7.0时,ADM与Eu3+、yb3+能形成稳定配合物,该配合物可使DNA的最大吸收产生明显的减色效应及红移,并能够竞争置换溴化乙锭(EB)与DNA的结合点.KI猝灭试验发现D...     

碱土金属盐中痕量铅的共沉淀分离富集及其机理研究

研究提出Ｃｕ（Ⅱ）＿ＰＤＣ在溶液ｐＨ２－１１时定量共沉淀碱土金属盐中的痕量铅,用ＦＡＡＳ测定,检出限可达１．５×１０＾２ｍｇ／Ｌ Ｐｂ（Ⅱ）,标准加入回收率在９８％－１０４％之间,克服了基体干扰,取得了较为满意的结果。同时对共沉淀机理进行了初步的研究探讨,结果表明其属于吸附共沉淀类型。     

高锰酸钾-鲁米诺反应体系中碱土金属离子Mg2+,Ca2+,Sr2+,Ba2+化学发光行为研究

将被认为没有化学发光活性的第二主族(碱土金属)离子Mg^2 ,Ca^2 ,Sr^2 ,Ba^2 溶液注入到已充分反应的高锰酸钾与鲁米诺混合液中时,又发生了新的化学发光反应,并检测到强的化学发光信号．在对有关反应的动力学性质、化学发光光谱、紫外可见光谱及其它一系列实验研究的基础上,提出了可能的化学发光反应机理．同时,优化了反应条件,评价了这一反应用于Mg^2 ,Ca^2 ,Sr^2 ,Ba^2 分析的可行性．     

碱金属和碱土金属促进的Ni/SiO2催化剂上甲烷的二氧化碳重整制合成气

Ni/SiO2 catalysts promoted by alkali metals K and Cs or alkaline earth metals Mg, Ca, Sr and Ba were prepared, characterized by H2-TPR and XRD, and used for the production of synthesis gas via methane reforming with CO2. Though K and Cs promoted Ni catalysts could eliminate coke deposition, the reforming activity of these promoted catalysts was decreased heavily. Mg and Ca promoted Ni/SiO2 catalysts exhibited excellent coke resistance ability with minor loss of the reforming activity of Ni/SiO2. Ba showed poor coke resistance ability and small amount of Sr increased the formation of coke. The possible mechanism of these promoters was discussed.     

水基溶胶-凝胶法制备稀土/碱土金属硅酸盐纳米粉

采用水基溶胶凝胶法,以廉价的无机盐Y2O3,MgO为前驱物,Si(OC2H5)4为络合剂,PEG4000为复合表面活性剂,氨水调节pH值,并利用无水乙醇超声分散技术,成功制备了分散性良好的稀土碱土金属复合硅酸盐纳米粉xY2O3·yMgO·zSiO2(YMS),考察了初始溶液的pH值、温度及浓度对溶液—溶胶—凝胶转变的影响,并利用TG DTA,XRD,TEM分析手段对复合硅酸盐纳米粉YMS的性质进行了研究。实验表明,在60℃相似文献   

基于柔性环己烷六酸配体的两个碱土金属配位聚合物的水热合成及结构表征(英文)

水热反应条件下,碳酸锰和碳酸钡分别与水合环己烷六酸(H6LⅠ·H2O)(顺式椅式构型LⅠ:a,e,a,e,a,e)反应生成2个三维的配位聚合物[Mg3(LⅡ)(H2O)6](1)和[Ba2(H2LⅡ)(μ2-H2O)2](2)(反式椅式构型LⅡ:e,e,e,e,e,e),通过元素分析和红外光谱对这2个配位聚合物进行了表征。X射线单晶衍射分析表明配合物1属于三方晶系,R3空间群,晶胞参数为:a=1.4393(2)nm,c=1.4597(4)nm,β=120.00°,V=2.6187(10)nm3,Z=18;配合物2结构属于单斜晶系,C2/c空间群,晶胞参数为:a=1.6764(2)nm,b=0.9095(1)nm,c=1.0001(1)nm,β=105.991(2)°,V=1.4659(2)nm3,Z=4。配合物1是由反式椅式构型LⅡ配体桥连形成的高对称性的三维配位网络。在配合物2中,顺式的H6LⅠ配体也发生构型转变并脱去部分羧基质子形成H2LⅡ配体,将Ba离子连接成一个具有一维孔道的三维有孔框架结构。在这2个配合物中,环己烷六酸配体均采取反式椅式LⅡ构型,证明了碱土金属离子Mg髤及Ba髤在水热条件下通过配位作用可以稳定环己烷六酸配体的这种反式椅式构型。