利用Raman散射光谱研究铜铟镓硒薄膜表面的掺杂调节作用

主要研究了采用溅射后硒化方法制备CIGS(铜铟镓硒)薄膜太阳电池的吸收体材料中的表面层掺杂调节问题。并利用Raman散射谱分析研究了样品表面层特征峰的移用,研究结果表明: CIGS薄膜表面层由富In表面层调节为富CuGa表面层后,Raman特征峰位向高波数移动,表明薄膜表面的Ga含量随之变化,并导致表面能带的相应改变,经计算证实了富CuGa表面层样品较之富In表面层样品具有更高的表面能带,从而改善了以此材料为吸收层的太阳电池器件性能, V_oc提高了74 mV,填充因子上升8％,最终使器件转换效率η相应提高了约2％。提高了V_oc与FF。同时表明Raman散射谱作为一种灵敏的表面表征手段,在研究太阳电池吸收层表面状态时十分有力。     

Effect of post annealing on the characteristics of In2S3 buffer layer grown by chemical bath deposition on a CIGS substrate

In₂S₃ as an alternative Cd-free buffer in Cu(In,Ga)Se₂ (CIGS) solar cells was deposited on CIGS substrate by a chemical bath deposition and characterized after post annealing to optimize film properties for CIGS solar cells. A uniform and pinhole-free In₂S₃ film was deposited on a CIGS substrate by H₂O₂ treatment prior to chemical bath deposition. The In₂S₃ layer was an amorphous state due to the co-existence of In–S, In–O, and In–OH bonds. Annealing at 200 °C induced copper diffusion from CIGS into In₂S₃ layer and lowered the band gap from 3.3 to 1.9 eV, leading to phase change from amorphous state to crystalline state. The conduction band alignment at the In₂S₃/CIGS interface can be controlled by the post annealing. The shunt current through In₂S₃ film was prevented down to the thickness of 30 nm and a 1.15 eV shallow defect was eliminated by the annealing. The results indicated that post annealing in air is a critical to fabricate CIGS solar cells with a sub-30 nm CBD-In₂S₃ buffer layer.     

Post-annealing effect on the reactively sputter-grown CIGS thin films and its influence to solar cell performance

Using a reactive co-sputtering from Cu_0.6Ga_0.4 and Cu_0.4In_0.6 alloy targets, we prepared CuIn_1−xGa_xSe₂ (CIGS) thin films on Mo/soda-lime glass (SLG) in association with a thermal cracker for elemental atomic Se radicals. The film growth was performed at 500 °C for 90 min. To achieve the composition ratio of CIGS absorber layer, Cu_0.6Ga_0.4 target was set at RF power of 50 W, 60 W, 70 W, and 80 W while keeping at 100 W for Cu_0.4In_0.6 alloy target. Post-annealing was done for all the CIGS films at 550 °C for 30 min. The composition ratio of [Cu]/[In + Ga] and [Ga]/[In + Ga] was increased with RF power but showed no change after post-annealing. X-ray diffraction analysis revealed all the samples has grown dominantly in the [112] crystal orientation. We found the Cu_2−xSe and (InGa)_2−xSe₃ defect phase both at the surface and in the bulk, and developed with post-annealing. From the devices fabricated in the structure of grid/ITO/i-ZnO/CdS/CIGS/Mo/soda-lime glass (SLG), the external quantum efficiency (EQE) was observed to improve in the wavelength, λ ≥ 550 nm in the samples treated with annealing. In the current–voltage (J–V) measurements, the solar cell showed the best performance of FF = 54.1%, V_oc = 0.48 V, J_sc = 33.1 mA/cm² and η = 8.5% in the sample with [Cu]/[In + Ga] = 0.84 that improved largely from η = 4.6% for the solar cell with an as-grown CIGS films.     

Cu(In,Ga)Se2 superstrate-type solar cells with Zn1−xMgxO buffer layers

Superstrate-type Cu(In,Ga)Se₂ (CIGS) thin film solar cells were fabricated using Zn_1−xMg_xO buffer layers. Due to the diffusion of Cd into CIGS during the growth of the CIGS layer, the conventional buffer material of CdS is not suitable. ZnO is a good candidate because of higher thermal tolerance but the conduction band offset (CBO) of ZnO/CIGS is not appropriate. In this study, the Zn_1−xMg_xO buffer layers were used to fulfill both the requirements. The superstrate-type solar cells with a soda-lime glass/In₂O₃:Sn/Zn_1−xMg_xO/CIGS/Au structure were fabricated with different band gap energies of the Zn_1−xMg_xO layer. The CIGS layers [Ga/(In + Ga)∼0.25] were deposited by co-evaporation method. The substrate temperature during the CIGS deposition of 450 °C did not cause the intermixing of the Zn_1−xMg_xO and CIGS layers. The conversion efficiency of the cell with Zn_1−xMg_xO was higher than that with ZnO due to the improvement of open-circuit voltage and shunt resistance. The results well corresponded to the behavior of the adjustment of CBO, demonstrating that the usefulness of the Zn_1−xMg_xO layer for the CBO control in the superstrate-type CIGS solar cells.     

Cu(In,Ga)Se2 thin film solar cells from nanoparticle precursors

A non-vacuum process for Cu(In,Ga)Se₂ (CIGS) thin film solar cells from nanoparticle precursors was described in this work. CIGS nanoparticle precursors was prepared by a low temperature colloidal route by reacting the starting materials (CuI, InI₃, GaI₃ and Na₂Se) in organic solvents, by which fine CIGS nanoparticles of about 15 nm in diameter were obtained. The nanoparticle precursors were then deposited onto Mo/glass substrate by the doctor blade technique. After heat treating the CIGS/Mo/glass layers in Se gas atmosphere, a complete solar cell structure was fabricated by depositing the other layers including CdS buffer layer, ZnO window layer and Al electrodes by conventional methods. The resultant solar cell showed a conversion efficiency of 0.5%.     

Cu元素对Cu(In,Ga)Se_2薄膜及太阳电池的影响

Cu元素成分对Cu(In,Ga)Se2(简称CIGS)薄膜材料的电学性质及其电池器件性能有很重要的影响.本文利用蒸发法制备了贫Cu和富Cu的CIGS吸收层(0.7Cu/(Ga+In)1.15)及相应的电池器件.扫描电镜和Hall测试发现,富Cu材料的结构特性(晶粒大、结晶状态好)和电学特性(电阻率低、迁移率高等)优于贫Cu材料,而性能测试表明贫Cu器件的效率优于富Cu器件.变温性能测试分析表明,贫Cu器件的主要复合路径是体复合,激活能与CIGS禁带宽度相当;富Cu器件的主要复合路径是界面复合,其激活能远小于CIGS禁带宽度,这大大降低了开路电压Voc,从而降低了电池效率.最后利用蒸发三步法制备了体材料稍富Cu表面贫Cu的CIGS吸收层,降低了短路电流和开路电压的损失,获得了超过15%的电池效率.     

Compositional investigation of potassium doped Cu(In,Ga)Se2 solar cells with efficiencies up to 20.8%

We report on the interaction between intentional potassium doping of thin film Cu(In,Ga)Se₂ (CIGS) solar cells, CIGS absorber composition, and device efficiency. Up to now high efficiency CIGS solar cells could not be produced with a gallium/(gallium + indium) ratio higher than 35%. The new doping process step does not only increase solar cell conversion efficiencies up to 20.8%, but also allows a shift in the CIGS absorber composition towards higher gallium content whilst maintaining this high efficiencies level. We find that the saturation of the open circuit voltages for higher gallium content that is normally observed can partially be overcome by the new doping procedure. This observation leads us to the conclusion that even on this high performance level CIGS solar cells still hold a potential for further development beyond the record values reported here. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Surface modification of CIGS film by annealing and its effect on the band structure and photovoltaic properties of CIGS solar cells

The composition of Cu(In,Ga)Se₂ (CIGS) films employed in CIGS solar cells is Cu deficient. There can be point defects, including Cu vacancies, Se vacancies, and metal anti-site defects. The surface composition and defects are not well controlled right after CIGS film fabrication with a three-stage co-evaporation process. This fabrication technique can result in a large variation in cell efficiency. In order to control the CIGS film in a reproducible way, we annealed the CIGS film in air, S, or Se. With this annealing procedure, the Cu content of the CIGS surface was significantly reduced and Ga content was strongly increased. An intrinsic CIGS layer with a lower valence-band maximum and a wider ban gap was formed at the surface. By annealing the CIGS film, the open-circuit voltage and fill factor were significantly improved, which indicates that the surface intrinsic layer acts as a hole-blocking layer so that the surface recombination rate is suppressed. In addition to CIGS film annealing, with subsequent annealing of the completed devices using rapid thermal annealing, the efficiency and reproducibility of CIGS solar cells were markedly improved.     

Cu(In,Ga)Se2 薄膜在共蒸发"三步法"中的相变过程

CIGS薄膜的结晶相是制备高质量薄膜的关键问题. 本文采用共蒸发"三步法"工艺沉积Gu(In, Ga)Se₂ (CIGS) 薄膜, 通过X射线衍射仪 (XRD) 和X射线荧光光谱仪 (XRF)、扫描电镜 (SEM) 结合的方法详细研究了"三步法"工艺的相变过程, 并制备出转换效率超过15% 的 CIGS 薄膜太阳电池. 关键词： CIGS薄膜 共蒸发三步法 相变过程     

Electroreflectance study of CuIn1−xGaxSe2 thin film solar cells

We have investigated the optical properties of CuIn_1−xGa_xSe₂ (CIGS) thin film solar cells using their electroreflectance (ER) at room temperature. The ER spectra exhibited one broad and two narrow signal regions. Using the photoluminescence (PL) and photocurrent (PC) spectra, the peaks in the low-energy region (1.02–1.35 eV) can be assigned to the CIGS thin film. The PC results implied that the peaks in the high-energy region (2.10–2.52 eV) can be assigned to the CdS band-gap energy. Using the applied bias voltage, the broad signals in the 1.35–2.09 eV region can be assigned to the Franz–Keldysh oscillation (FKO) due to the internal electric field. The ER spectra exhibited a distorted CdS signal for the CIGS thin film solar cell with low shunt resistance and efficiency.     

Photovoltaic performance of flexible Cu(In,Ga)Se2 thin-film solar cells with varying Cr impurity barrier thickness

We report the effect of Cr impurity barrier on Cu(In,Ga)Se₂ (CIGS) thin-film solar cells prepared on flexible substrates. The Cr films with varying the thickness (t_Cr) were deposited on stainless steel substrates using direct-current magnetron sputtering. The solar cell performance was improved by increasing t_Cr since the diffusion of Fe impurities from the substrate to CIGS was suppressed. Although the elemental composition, grain size, and strain of CIGS film showed little change with varying Fe content, the fill factor and the short-circuit current density increased as decreasing Fe. The Fe increased the series resistance, shunt paths, and saturation current density. The reduction of Fe caused a steeper bandgap grading in CIGS which enhances current collection due to higher electric fields in bulk CIGS. CIGS solar cells with 1000 nm-thick Cr barrier showed the best conversion efficiency of 9.05%.     

Effects of Ga contents on properties of CIGS thin films and solar cells fabricated by co-evaporation technique

This study examined the effects of Ga content in the CIGS absorber layer on the properties of the corresponding thin films and solar cells fabricated using a co-evaporation technique. The grain size of CIGS films decreased with increasing Ga content presumably because Ga diffusion during the 2nd stage of the co-evaporation process is more difficult than In diffusion. The main XRD peaks showed a noticeable shift to higher diffraction angles with increasing Ga content, which was attributed to Ga atoms substituting for In atoms in the chalcopyrite structure. Band gap energy and the net carrier concentration of CIGS films increased with Ga/(In + Ga) ratios. Regarding the solar cell parameters, the short circuit current density (J_SC) decreased linearly with Ga/(In + Ga) ratios due to the lack of absorption in the long-wavelength portion of the spectrum, while the open circuit voltage (V_OC) increase with those. However, V_OC values at high Ga/(In + Ga) regions (>0.35) was far below than those extrapolated from the low Ga contents regions, finally resulting in an optimum Ga/(In + Ga) ratio of 0.28 where the solar cell showed the highest efficiency of 15.56% with V_OC, J_SC and FF of 0.625 V, 35.03 mA cm⁻² and 0.71, respectively.     

Ga梯度分布对Cu(In,Ga)Se_2薄膜及太阳电池的影响

传统制备Cu(In,Ga)Se2(CIGS)手段之一是共蒸发三步法,工艺中通过Cu,In,Ga,Se 4种元素相互扩散、作用形成抛物线形的Ga梯度分布.本文通过调整Ga源温度制备了Ga梯度分布不同的CIGS薄膜及电池.利用多种测试方法,研究了Ga梯度分布不同对CIGS薄膜表面及背面结构性质及电性质的影响,计算分析了表面导带失调值及背面电场对电池性能的影响,从而获得了合适的Ga梯度分布,提高了电池光谱相应,获得了较好的电池性能参数.     

Characterization of CBO and defect states of CZTSe solar cells prepared by using two-step process

We fabricated kesterite Cu₂ZnSnSe₄ (CZTSe) solar cells and studied device characteristics, where CZTSe absorbers were made by using two-step process. First, we deposited precursor CZTSe films with spin-coating or sputtering, and performed sulfurization and subsequent selenization. To complete the device, we applied In₂S₃ as a buffer layer. We obtained power conversion efficiency (PCE) of 4.18% with spin-coated CZTSe absorber and 5.60% with sputtered CZTSe absorber. Both devices showed deep defects in the bulk and strong interface recombinations near the pn junction. In addition, we observed red-kinks in the current density-voltage (J-V) curves for both devices under the filtered light illumination (>660 nm), which is attributed to large conduction band offset (CBO) between the CZTSe absorber and the buffer layer and defect states in the buffer/CZTSe absorber or in the buffer. The red-kink was also observed in CZTSe (PCE of 7.76%) solar cell with CdS buffer. Hence, to enhance the PCE with CZTSe absorber, along with suppression of deep defects which act as recombination center, optimization of CBO between absorber and buffer is also required.     

Computational analysis of the effect of the surface defect layer (SDL) properties on Cu(In,Ga)Se2-based solar cell performances

In this article, the performances of Cu(In,Ga)Se₂ (CIGS) solar cells have been modelled and numerically simulated using the one-dimensional simulation program Solar Cell Capacitance Simulator in 1 Dimension (SCAPS-1D), and a detailed analysis of the effect of surface defect layer (SDL) thickness, band gap and carrier mobility with Fermi level pinning is presented. Furthermore, donor-type defect state density in the SDL has been investigated, and their effect on device performances has been presented. Based on the simulation results, optimal properties of the SDL for the CIGS solar cell are proposed. The simulated results show that the optimal thickness of the SDL to optimise the solar cells is in the range of 100–200 nm. The increase in the band gap of the SDL >1.3 eV improves the device performance by enhancing the open-circuit voltage (V_oc), fill factor (FF) and conversion efficiency due to the larger quasi-Fermi energy-level splitting, and optimal band offset between the SDL and the buffer layer (CdS). The simulation results suggest that the SDL defect density as well as carrier mobilities are the critical parameters for the limitation of the performances for the CIGS solar cells. All these results show that the SDL plays an important role in designing high-efficiency and high-performance CIGS-based solar cells.     

A new method of generating Ga slope in Cu(In,Ga)Se2 film by controlling Se content in a multi-stacked precursor

An appropriate Ga slope is required in Cu(In,Ga)Se₂ (CIGS) film to enhance the cell performance of CIGS thin-film solar cells. In the conventional three-stage-co-evaporation process, the Ga slope was obtained by controlling Ga/In flux during deposition process. However, in two-step process, where a precursor was deposited first and then annealed in a Se environment for mass production, the desirable Ga slope was not achievable with the Ga/In flux control. We observed that the Ga/(Ga + In) ratio was nearly flat in CIGS film for Se-rich precursor and the ratio was nearly zero at surface and very high on bottom side of CISG film for Se-deficient precursor. We were able to generate a CIGS film with a Ga non-zero Ga surface and desired slope in the bulk by devising a precursor with Se-rich layer on top and Se-deficient layer on bottom, resulting in the enhancement of Cell performance.     

Nd:YAG laser ablation characteristics of thin CIGS solar cell films

This work reports that the ablation characteristics of thin CuIn_1?x Ga _x Se₂ (CIGS) solar cell film differ significantly with elemental composition and laser pulse energy. From in situ shadowgraphs measured during Nd:YAG laser (1,064 nm) irradiation of CIGS films and crater morphologies, it was found that strong surface evaporation is dominant for low Ga concentration films of which band gap is well below the photon energy. As the band gap of CIGS film becomes close to or over the laser photon energy due to increased Ga content, surface absorption diminishes and at low laser energy, laser heating of the film plays an important role. It is demonstrated that for the CIGS films with Ga/(Ga + In) ratio being approximately over 0.2, the laser irradiation leads to solid phase removal of the film due to thermomechanical fracture at low laser energy but to ablative evaporation at elevated energy.     

Effects of heavy alkali elements in Cu(In,Ga)Se2 solar cells with efficiencies up to 22.6%

We report on the use and effect of the alkali elements rubidium and caesium in the place of sodium and potassium in the alkali post deposition treatment (PDT) as applied to Cu(In,Ga)Se₂ (CIGS) solar cell absorbers. In order to study the effects of the different alkali elements, we have produced a large number of CIGS solar cells with high efficiencies resulting in a good experimental resolution to detect even small differences in performance. We examine the electrical device parameters of these fully functional devices and observe a positive trend in the I –V parameters when moving from devices without PDT to KF‐, RbF‐, and eventually to CsF‐PDT. A diode analysis reveals an improved diode quality for cells treat‐ed with heavier alkalis. Furthermore, secondary ion mass spectrometry (SIMS) measurements reveal a competitive mechanism induced within the class of alkali elements in the CIGS absorber induced by the alkali post deposition treatment. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

A new simple route to grow Cu(In,Ga)Se2 thin films with large grains in the co-evaporation process

In the conventional three-stage co-evaporation process to grow Cu(In,Ga)Se₂ (CIGS) film, a large grain is achieved by the co-evaporation of Cu and Se on (In,Ga)₂Se₃ layer at 550 °C in the second stage and then a p-type is achieved by the co-evaporation of In, Ga, and Se in the third-stage. We reported a new process where a CIGS film with a large gain and p-type is achieved by evaporation of Cu only in the second stage at 400 °C and by the Se annealing in the third stage. In the new process, thermal budget was lowered and the third-stage co-evaporation process was eliminated. It was found that the CIGS gain size increased when the Cu/(In + Ga) ratio was above 0.7 and an addition thin CIGS layer appeared on the CIGS surface. The reaction path with Cu was described in the Cu-In-Se ternary phase diagram. The cell conversion efficiency increased from 9.6 to 15.4% as the Se annealing temperature increased from 400 to 550 °C in the third stage, mainly due to the increase of open-circuit voltage and fill factor. Our process demonstrated a new route to grow a CIGS film with a less thermal budget and simpler process in the co-evaporation process.     

A comparative study of solution based CIGS thin film growth on different glass substrates

CuIn_xGa_1−xSe_yS_2−y (CIGS) thin films were synthesized on glass substrates by a paste coating of Cu, In, and Ga precursor solution with a three-step heat treatment process: oxidation, sulfurization, and selenization. In particular, morphological changes of CIGS films for each heat treatment step were investigated with respect to the kinds of glass substrates: bare, Mo-coated, and F-doped SnO₂ (FTO) soda-lime glasses. Very high quality CIGS film with large grains and low degree of porosity was obtained on the bare glass substrate. Similar morphology of CIGS film was also acquired on the Mo-coated glass except the formation of an undesired Mo oxide interfacial layer due to the partial oxidation of Mo layer during the first heat treatment under ambient conditions. On the other hand, CIGS film with much smaller grains and higher degree of porosity was gained when FTO glass was used as a substrate, resulting in slight solar to electricity conversion behavior (0.20%). Higher power conversion efficiency (1.32%) was attained by the device with the CIGS film grown on Mo-coated glass in spite of the presence of a Mo oxide impurity layer.