Influence of laser power on POCl3 diffused back surface field on n-type PERT silicon solar cells with local back contact

We report n-type passivated emitter rear totally diffused (PERT) silicon solar cells with local back contacts (LBC) formed by laser process. With passivated back surface field (BSF), the PERT cell design shows an improved open circuit voltage (V_oc) with reduced recombination at the rear due to improved optical confinement. The rear side was diffused by POCl₃ diffusion with low sheet resistance (R_s) BSF and passivated using SiN_x. Laser ablation was used to open the SiN_x on the rear for LBC. The Nd:YAG laser power (mW) parameters and POCl₃ doping temperature were varied to obtain the BSF with lower sheet resistance. Laser power of 44 mW with 10 kHz resulted in 30 Ω/sq BSF layer with effective lifetime (τ_eff) of 90 μs and a higher V_oc of 646 mV. With the optimized laser parameters the best electrical results yielded a short circuit current density (J_sc) of 36 mA/cm² and efficiency of 18.54%.     

21.0%‐efficient co‐diffused screen printed n‐type silicon solar cell with rear‐side boron emitter

Plasma enhanced chemical vapor deposition (PECVD) is applied to deposit boron silicate glasses (BSG) acting as boron diffusion source during the fabrication of n‐type silicon solar cells. We characterize the resulting boron‐diffused emitter after boron drive‐in from PECVD BSG by measuring the sheet resistances R_sheet,B and saturation current densities J_0,B. For process optimization, we vary the PECVD deposition parameters such as the gas flows of the precursor gases silane and diborane and the PECVD BSG layer thickness. We find an optimum gas flow ratio of SiH₄/B₂H₆= 8% and layer thickness of 40 nm. After boron drive in from these PECVD BSG diffusion sources, a low J_0,B values of 21 fA/cm² is reached for R_sheet,B = 70 Ω/□. The optimized PECVD BSG layers together with a co‐diffusion process are implemented into the fabrication process of passivated emitter and rear totally diffused (PERT) back junction (BJ) cells on n‐type silicon. An independently confirmed energy conversion efficiency of 21.0% is achieved on 15.6 × 15.6 cm² cell area with a simplified process flow. This is the highest efficiency reported for a co‐diffused n‐type PERT BJ cell using PECVD BSG as diffusion source. A loss analysis shows a small contribution of 0.13 mW/cm² of the boron diffusion to the recombination loss proving the high quality of this diffusion source. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

a-Si(n)/c-Si(p)异质结太阳电池薄膜硅背场的模拟优化

采用AFORS-HET数值模拟软件,对不同带隙的薄膜硅材料在a-Si(n)/c-Si(p)异质结太阳电池上的背场效果进行了模拟,分析了影响背场效果的原因,得到了薄膜硅背场在a-Si(n)/c-Si(p)异质结太阳电池上的适用条件为薄膜硅材料是带隙16 eV,硼掺杂浓度在10¹⁸cm^-3以上的微晶硅材料,其最佳厚度在5nm左右. 这种背场从工艺上易于实现,并且,与常用的Al扩散背场相比,在相同的掺杂浓度下,电池效率可以大大提高. 关键词： 薄膜硅 背场 硅异质结太阳电池     

CdTe太阳电池的不同背电极和背接触层的特性研究

用Ni替代Au来作为CdTe太阳电池的背电极，比较了Ni,Ni/Au,Au/Ni及Au背电极对电池性能的影响.发现Ni作为背电极和ZnTe/ZnTe:Cu复合层接触，电池的开路电压V_oc略有降低，填充因子FF有增有减，变化幅度不大，但因短路电流I_sc有较大的提高，转换效率η平均增长4％.测试了不同背电极的CdTe太阳电池的暗I-V和C-V特性，对背电极剥离后的样品进行了XPS测试分析.结果表明，Ni扩散到ZnTe/ZnTe:Cu复合层的深度比Au多，且大多呈离子态，与ZnTe/ZnTe:Cu复合层中的富Te离子形成Ni_xTe，提高了掺杂浓度，使电池性能获得改善. 关键词： 金属背电极 复合背接触层 转换效率 CdTe太阳电池     

TiO2 treatment using ultrasonication for bubble cavitation generation and efficiency assessment of a dye-sensitized solar cell

In this study, the impacts of different ultrasonic treatments on TiO₂ particles were determined and they were used to manufacture the photoelectrodes of a dye-sensitized solar cell (DSSC). Two methods were used to prepare TiO₂ particles directly sonicated by an ultrasonic horn, and TiO₂ treated indirectly by an ultrasonic cleaner. TEM, XPS analysis was confirmed that cavitation bubbles generated during ultrasonication resulted in defects on the surface of TiO₂ particles, and the defect induced surface activation. To understand the effect of TiO₂ surface activation on energy conversion efficiency of DSSC, ultrasonic horn DSSC and ultrasonic cleaner DSSC were prepared. The UV–vis analysis exhibited that the ultrasonic horn DSSC possessed higher dye adsorption when compared to the ultrasonic cleaner DSSC, and the EIS analysis confirmed that the electron mobility was greatly increased in the ultrasonic horn DSSC. The energy conversion efficiency of the ultrasonic horn DSSC was measured to be 3.35%, which is about 45% increase in comparison to that of the non-ultrasonic treated DSSC (2.35%). In addition to this regard, recombination resistance of ultrasonic horn DSSC was calculated to be 450 Ω·cm², increasing more than two times compared to the non-ultrasonic treated DSSC (200 Ω·cm²). Taken together, these ultrasonic treatments significantly improved the energy conversion efficiency of DSSC, which was not tried in DSSC-related research, and might lead us to develop more efficient practical route in the manufacturing of DSSC.     

界面缺陷态密度与衬底电阻率取值对硅异质结光伏电池性能的影响

在异质结前界面缺陷态密度Dit1和异质结背界面缺陷态密度Dit2均取不同值时,对p型单晶硅(c-Si(p))为衬底的硅异质结太阳电池的衬底电阻率ρ与电池性能的关系进行了数值研究.结果表明:衬底电阻率的最优值ρop取决于前界面缺陷态密度Dit1,且ρop随着Dit1的增大而增大;当ρρop时,背界面缺陷态密度Dit2对衬底电阻率的可取值范围具有较大影响,Dit2越大衬底电阻率的可取值范围越小.     

选择性发射极晶体硅太阳电池的二维器件模拟及性能优化

利用PC2D二维模拟软件对选择性发射极晶体硅太阳电池(SE电池)进行了器件模拟和参数优化的研究.在对丝网印刷磷浆法制备的SE电池的实测典型电流-电压曲线实现完美拟合的基础上,全面系统地研究了栅线、基区、选择性发射区和背表面场层等的参数对电池性能的影响.模拟表明:基区少子寿命、前表面复合速度和背表面复合速度是对电池效率影响幅度最大的三个参数.在所研究的参数范围内,当基区少子寿命从50μs上升到600μs时,电池效率从18.53%上升到19.27%.低的前表面复合速度是使发射区方块电阻配比优化有意义的前提.要取得理想的电池效率,背表面复合速度需控制在500 cm/s以下.此外,对于不同的前表面复合速度,电池效率的最大值总是在50—90Ω/□的重掺区方阻、110—180Ω/□的轻掺区方阻的范围内取得.对不同的栅线数目,重掺区宽度与栅线间距之比为32%时,电池的效率最高.另外,在主栅结构保持较低面积比率的前提下,主栅数目的增加也可提高效率.最后,通过优化p型SE电池的效率可达到20.45%.     

High efficiency ETM-free perovskite cell composed of CuSCN and increasing gradient CH3NH3PbI3

To enhance device performance and reduce fabrication cost,a series of electron transporting material(ETM)-free perovskite solar cells(PSCs)is developed by TCAD Atlas.The accuracy of the physical mode of PSCs is verified,due to the simulations of PEDOT:PSS-CH₃NH₃PbI₃-PCBM and CuSCN-CH₃NH₃PbI₃-PCBM p-i-n PSCs showing a good agreement with experimental results.Different hole transporting materials(HTMs)are selected and directly combined with n-CH₃NH₃PbI₃,and the CuSCN-CH₃NH₃PbI₃ is the best in these ETM-free PSCs.To further study the CuSCN-CH₃NH₃PbI₃ PSC,the influences of back electrode material,gradient band gap,thickness,doping concentration,and bulk defect density on the performance are investigated.Energy band and distribution of electric field are utilized to optimize the design.As a result,the efficiency of CuSCN-CH₃NH₃PbI₃ PSC is achieved to be 26.64%.This study provides the guideline for designing and improving the performances of ETM-free PSCs.     

A12o3钝化及其在晶硅太阳电池中的应用

介绍了A1203的材料性质及其原子层沉积制备方法,详细阐述了该材料的钝化机制（化学钝化和场效应钝化）,并从薄膜厚度、热稳定性及叠层钝化等角度阐释其优化方案．概述了Al203钝化在晶体硅太阳电池中的应用,主要包括钝化发射极及背面局部扩散电池和钝化发射极及背表面电池．最后,对A1203钝化工艺的未来研究方向和大规模的工业应用进行了展望．     

Al2O3钝化及其在晶硅太阳电池中的应用

介绍了Al₂O₃的材料性质及其原子层沉积制备方法, 详细阐述了该材料的钝化机制(化学钝化和场效应钝化), 并从薄膜厚度、热稳定性及叠层钝化等角度阐释其优化方案. 概述了Al₂O₃钝化在晶体硅太阳电池中的应用, 主要包括钝化发射极及背面局部扩散电池和钝化发射极及背表面电池. 最后, 对Al₂O₃钝化工艺的未来研究方向和大规模的工业应用进行了展望.     

Composition-dependent phase separation effects of organic solar cells using P3HT:PCBM as active layer and chromium oxide as hole transporting layer

Phase separation of the poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) active layer (ATL) was investigated by varying their relative ratio in the organic solar cells (OSCs). With the help of the UV/visible spectrophotometer, optical microscopy and scanning electron microscope, we found that the cluster of PCBM at the interface or surface was affected by Al cathode, the composition of the blends and thermal annealing. The disc-like shape crystals of PCBM substituted for the needle-like ones at higher PCBM compositions at the ATL/Al interface, which led to stronger contacts and bigger contact area. It could make short circuit current density increase, but may affect the blend morphology and result in parallel resistance and open circuit voltage decreased with the PCBM ratio increasing from 40 to 60%. The microstructure of the P3HT:PCBM ATL, determined by the composition dependent phase separation, supported the optimized performance of the OSCs with the composition of 40-50% PCBM.