水对Ni/MgAlO催化丙酮加氢的影响

研究了H2O对Ni/MgAlO催化剂上丙酮加氢为异丙醇的催化反应的影响。结果发现,在丙酮中添加少量H2O可提高丙酮转化率,但超过5%的H2O量则会显著降低催化剂活性。吸附量热结果表明,催化剂表面吸附少量H2O会明显降低异丙醇的吸附热,但对丙酮吸附热的影响较小,这也许是反应体系中少量的H2O能促进丙酮加氢活性的原因之一。当催化剂表面吸附较多H2O后,丙酮、异丙醇和H2的吸附热都降低了,因此反而抑制了丙酮的加氢反应。此外,红外光谱结果表明,预吸附水抑制了催化剂表面异丙醇脱氢生成丙酮,并抑制吸附的丙酮在表面生成烯醇盐或异丙叉丙酮等物种,这也许是少量水能促进丙酮加氢生成异丙醇的另一个重要原因。     

水对Ni/MgAlO催化丙酮加氢的影响（英文）

研究了H2O对Ni/Mg Al O催化剂上丙酮加氢为异丙醇的催化反应的影响.结果发现,在丙酮中添加少量H2O可提高丙酮转化率,但超过5%的H2O量则会显著降低催化剂活性.吸附量热结果表明,催化剂表面吸附少量H2O会明显降低异丙醇的吸附热,但对丙酮吸附热的影响较小,这也许是反应体系中少量的H2O能促进丙酮加氢活性的原因之一.当催化剂表面吸附较多H2O后,丙酮、异丙醇和H2的吸附热都降低了,因此反而抑制了丙酮的加氢反应.此外,红外光谱结果表明,预吸附水抑制了催化剂表面异丙醇脱氢生成丙酮,并抑制吸附的丙酮在表面生成烯醇盐或异丙叉丙酮等物种,这也许是少量水能促进丙酮加氢生成异丙醇的另一个重要原因.     

Ni-Mo/Al_2O_3催化剂上硫转移反应的研究

制备了以γ-Al2O3为载体的Ni-Mo催化剂,并用于FCC汽油的加氢硫转移反应。对Ni-Mo/Al2O3催化剂上的硫转移反应机理进行了研究,考察了不同反应条件对硫转移反应的影响。实验结果表明,硫醇与烯烃的反应在催化剂表面的加氢活性位上进行,小分子的硫醇发生加氢脱硫,生成吸附态H2S,吸附态的H2S与烯烃反应,生成大分子硫醇和硫醚;另外小分子硫醇还可直接与烯烃发生反应,生成硫醚。提高反应温度、压力、氢油比或降低空速,均可提高催化剂的硫转移反应活性,轻质硫转化率得到明显提高,且单烯选择性还能维持在98%左右。     

CO加氢合成C2含氧化合物Rh-Sm-V-Li/SiO2催化剂的研究

使用加压下的CO加氢反应和程序升温还原(TPR),吸附氢的程序升温脱附(H2-TPD),以及H2和CO吸附等技术,研究了Rh-Sm-V-Li/SiO2催化剂上Sm,V和Li促进剂对合成二碳含氧化合物的促进效应.结果表明,Sm和V加入到Rh/SiO2中使催化剂的活性和生成二碳含氧化合物的选择性显著提高,催化剂上的Sm3+不易被还原,Sm的加入起着提高Rh分散度的作用,使催化剂上H2和CO吸附量提高,并促进乙酸和乙醛的生成;催化剂上的高价钒离子容易还原成低价钒离子,并迁移覆盖金属Rh的表面,使催化剂上H2和CO吸附量降低.低价钒具有良好的贮氢能力,使催化剂的加氢能力显著提高,促进乙醇的生成.     

锰助剂对F-T合成Co/Al2O3催化剂反应性能的影响

采用程序升温和原位红外技术对锰改性Co/Al2O3催化剂进行了表征，并与CO加氢反应活性和选择性进行关联.结果表明，添加适量锰能够增加反应活性，提高烃选择性，抑制甲烷及低碳烃的生成. XRD和FT IR结果表明锰助剂的添加能够促进活性相的分散，促进桥式CO吸附位数的增加. H2 TPD表明锰的加入可增加低温吸附氢量，但吸附氢量随锰含量的增加而减少.钴基催化剂的费托合成反应性能可以用锰添加导致的CO吸附态物种的变化来解释.     

乙苯脱氢与逆水煤气变换偶合反应的铁/活性炭催化剂研究

 研究了活性炭负载的Fe催化剂在乙苯脱氢与逆水煤气变换偶合反应中的催化活性,考察了催化剂中的铁物相,添加Li,Na和K等碱金属以及CO2对催化活性的影响. 实验表明, Fe3O4可能是偶合反应的活性相. 在CO2气氛中,适当还原度的、经碱金属元素调变后的Fe/AC的催化活性较好,苯乙烯的选择性明显提高. 以NH3和CO2为探针分子,运用微分吸附量热技术表征了催化剂的表面酸碱性质. 结果表明,活性炭表面具有较多的弱酸位. 担载铁后,NH3的起始吸附热为96 kJ/mol, 吸附饱和覆盖度为112 μmol/g, 说明Fe/AC表面具有酸性; CO2的起始吸附热为72 kJ/mol, 吸附饱和覆盖度为7 μmol/g, 表明催化剂表面也有少量的碱位. 碱金属元素的加入减弱了Fe/AC催化剂表面上的酸强度,同时产生了一定量的碱性位,因而显著提高了苯乙烯的选择性. CO2的作用是及时除去脱氢反应产生的H2, 促进乙苯脱氢生成苯乙烯,并抑制乙苯的加氢裂解.     

负载型Ru基催化剂用于丙酮常压气相加氢

采用气相脉冲法，首次将非晶态Ru-B合金催化剂用于催化丙酮常压气相加氢反应．研究结果表明负载型Ru-B合金催化剂在较低的反应温度下表现出了很高的活性及生成异丙醇的选择性；负载在γ-Al2O3上的非晶态Ru-B合金与晶态的Ru相比，活性及异丙醇的产率都有很大提高；采用不同载体的非晶态Ru-B合金催化剂活性不同，在所选定的反应温度下，以膨润土为载体的Ru-B合金催化剂的活性与异丙醇的产率均高于以γ-Al2O3作载体的．用程序升温还原(TPR)，程序升温脱附(TPD)，等离子体发射光谱(ICP)等方法对催化剂表面性质及含量进行了表征．     

Rh基催化剂上CO加氢制C2含氧化合物的红外光谱研究

 用红外光谱法考察了Rh-Mn-Li-Ti/SiO2催化剂在CO加氢反应过程中表面吸附物种随压力、温度和H2/CO比的改变而变化的规律. 结果表明,高压有利于提高催化剂表面吸附的CO浓度和活性,高温有利于CO解离; 而高温、高压条件不但促进了CO吸附,而且提高并平衡了CO的解离和插入之间的相对活性,促进了C2含氧化合物的生成. H2/CO比的增大有利于CO在催化剂表面的吸附,从而促进了CO插入,尤其是CO的解离和加氢活性,但是过高的H2/CO比将导致过高的CO解离和加氢活性,引起CO插入活性的削弱而最终导致C2含氧化合物生成活性的下降. 同时,考察了助剂(Mn, Li和Ti)对Rh基催化剂表面吸附物种的影响. 结果表明,助剂的加入可提高C2含氧化合物的生成活性.     

原位漫反射红外光谱法研究SO2对Ag/Al2O3选择性催化丙烯还原NOx反应的影响

 以Ag/Al2O3为催化剂,采用原位漫反射傅里叶变换红外光谱法研究了SO2对C3H6选择性还原NOx反应的影响. 结果表明, SO2在催化剂表面转化为硫酸盐,并且随着硫酸盐累积量的增加,其主要红外特征吸收峰由低波数向高波数漂移. 高浓度表面硫酸盐的存在不仅抑制了催化剂表面硝酸盐的生成,而且抑制了硝酸盐与表面烯醇式物种(RCH=CH-O-)或乙酸盐物种进一步反应,生成活泼的反应中间体异氰酸酯(-NCO), 这是导致Ag/Al2O3催化剂上C3H6选择性还原NOx活性降低的主要原因.     

NiW/γ-Al2O3加氢催化剂化学吸附性质的研究

采用脉冲色谱法测定了噻吩在硫化态NiW/γ-Al2O3催化剂上化学吸附过程中热力学函数的变化,并与噻吩加氢脱硫(HDS)反应活性进行了关联.结果表明,噻吩在硫化态NiW/γ-Al2O3催化剂上的吸附不能太强,催化剂中的Ni可以降低噻吩在催化剂表面上的吸附强度,增加HDS反应活性中心的数目.从H2在硫化态NiW/γ-Al2O3催化剂上吸附后的程序升温脱附实验结果发现,H2在硫化态催化剂上有两种吸附态,高温脱附所对应的吸附态与HDS反应有关.     

Furfural Hydrogenation on Nickel‐promoted Cu‐containing Catalysts Prepared from Hydrotalcite‐Like Precursors

The nickel‐promoted Cu‐containing catalysts (Cu_xNi_y‐MgAlO) for furfural (FFR) hydrogenation were prepared from the hydrotalcite‐like precursors, and characterized by X‐ray powder diffraction, inductively‐coupled plasma atomic emission spectroscopy, N₂ adsorption‐desorption, UV‐Vis diffuse reflectance spectra and temperature‐programmed reduction with H₂ in the present work. The obtained catalysts were observed to exhibit a better catalytic property than the corresponding Cu‐MgAlO or Ni‐MgAlO samples in FFR hydrogenation, and the CuNi‐MgAlO catalyst with the actual Cu and Ni loadings of 12.5 wt% and 4.5 wt%, respectively, could give the highest FFR conversion (93.2%) and furfuryl alcohol selectivity (89.2%). At the same time, Cu⁰ species from the reduction of Cu²⁺ ions in spinel phases were deduced to be more active for FFR hydrogenation.     

非负载镍催化剂的2-乙基蒽醌加氢活性及其氢吸脱附性质

 分别制备了金属镍粉、兰尼镍、Ni-B非晶态合金及镧掺杂的Ni-B非晶态合金(Ni-B-La)催化剂,研究了催化剂的氢吸附和脱附性质以及对2-乙基蒽醌加氢反应的催化性能. 结果表明,金属镍粉、兰尼镍和Ni-B催化剂表面均具有两种氢吸附位: 弱吸附位和强吸附位. Ni-B-La催化剂表面只有氢的强吸附位,其强吸附氢量与兰尼镍相当. 推测只有氢的强吸附位是2-乙基蒽醌加氢反应的活性中心,并且Ni-B-La催化剂上的强吸附氢较兰尼镍上的更活泼,因而Ni-B-La非晶态合金催化剂对加氢反应的催化活性高于兰尼镍.     

Ni‐W Catalysts Supported on HZSM‐5/HMS for the Hydrogenation Reaction of Aromatic Compounds: Effect of Ni/W Ratio on Activity,Stability, and Kinetics

Ni‐W/HZSM5‐HMS catalysts were evaluated for the benzene hydrogenation reaction at 130–190°C. To study the catalyst characterization, X‐ray diffraction, X‐ray fluorescence, Fourier transform infrared, UV–vis, diffuse reflectance spectra, temperature‐programmed desorption of NH₃, FT‐IR of adsorbed pyridine measurements (Py‐IR), H₂ chemisorption, nitrogen adsorption–desorption, and TGA techniques were used. Kinetics of benzene hydrogenation was investigated under various hydrogen and benzene pressures, and the effect of reaction conditions on catalytic performance was studied. The results showed that bimetallic catalysts have better ability than a monometallic catalyst (Ni/HZSM5‐HMS) for this reaction, such as maximum benzene conversion (100%), minimum toluene conversion (1.76–40%), very low converted xylene, benzene selectivity (100%), good catalytic stability against coke deposition, and appropriate kinetic parameters.     

镍掺杂对Fe催化剂上CO_2加氢制烃影响的理论计算研究

为研究镍掺杂对铁基催化剂上二氧化碳加氢生成C_1和C_2烃类产物的影响,应用密度泛函理论进行了相关计算.在Fe(110)和Ni-Fe(110)表面上, CH~*物种是最有利的生成CH_4和C_2H_4的C_1物种(CH_x~*),其最可能的生成路径为CO_2→HCOO~*→HCO~*→CH~*.尽管CO_2直接解离为CO~*在动力学上相较于加氢生成HCOO~*和COOH~*是较为有利的,但CO~*进一步加氢生成HCO~*在能量上是不利的,其倾向于逆向解离回到CO~*. CH~*物种可以通过三步加氢反应生成CH_4或者经C—C耦合及两步加氢生成C_2H_4.在Fe(110)表面上,对甲烷和乙烯产物选择性起决定作用的基元反应能垒之间差异仅为0.10 eV,因此两者选择性相近.在将Ni原子引入Fe(110)表面后,生成甲烷与乙烯的选择性差异变大,导致乙烯的选择性提高.计算结果表明,添加少量金属Ni能够促进CO_2转化为CH~*,及两个CH~*物种发生C—C耦合和进一步加氢转化为乙烯.     

甲烷干重整反应用Ni-Ru/MgAl类水滑石催化剂的研究

采用焙烧记忆法分别制备Ni/Mg Al O和NiRu/Mg Al O类水滑石催化剂用于甲烷干重整反应.利用XRD、TPR、TG、XPS、CO2-TPD、TEM等表征催化剂的结构及失活特征,发现在Ni/Mg Al O中添加Ru,有利于增加催化剂表面Ni含量,并促进Ni2+的还原.不同Mg/Al比双金属催化剂中,7Ni-0.15Ru/Mg2.5Al催化剂具有较高的催化活性,这归结为该催化剂适宜的碱性、较高表面Ni含量以及小尺寸的Ni0物种.添加Ru明显抑制Ni/Mg Al O催化剂表面的丝状碳的形成.而7Ni-0.15Ru/Mg2.5Al较强的抗积碳性能与其较小Ni0晶粒尺寸及适宜催化剂碱性有关.     

Experimental microkinetic approach of the photocatalytic oxidation of isopropyl alcohol on TiO2. Part 1. Surface elementary steps involving gaseous and adsorbed C3H(x)O species

The present study concerns an experimental microkinetic approach of the photocatalytic oxidation (PCO) of isopropyl alcohol (IPA) into acetone on a pure anatase TiO2 solid according to a procedure previously developed. Mainly, the kinetic parameters of each surface elementary step of a plausible kinetic model of PCO of IPA are experimentally determined: natures and amounts of the adsorbed species and rate constants (preexponential factor and activation energy). The kinetics parameters are obtained by using experiments in the transient regime with either a FTIR or a mass spectrometer as a detector. The deep oxidation (CO2 and H2O formation) of low concentrations of organic pollutants in air is one of the interests of the PCO. For IPA, literature data strongly suggest that acetone is the single route to CO2 and H2O and this explains that the present study is dedicated to the elementary steps involving gaseous and adsorbed C3H(x)O species. The microkinetic study shows that strongly adsorbed IPA species (two species denoted nd-IPA(sads) and d-IPA(sads) due to non- and dissociative chemisorption of IPA, respectively) are involved in the PCO of IPA. A strong competitive chemisorption between IPA(sads) and a strongly adsorbed acetone species controls the high selectivity in acetone of the PCO at a high coverage of the surface by IPA(sads). The kinetic parameters of the elementary steps determined in the present study are used in part 2 to provide a modeling of macroscopic kinetic data such as the turnover frequency (TOF in s(-1)) of the PCO using IPA/O2 gas mixtures.     

担载型钌催化剂吸附CO性能的原位红外研究

用原位红外研究了ＣＯ的吸附与脱附，ＣＯ／Ｈ２的共吸附及反应，考察了焙烧温度对Ｒｕ／Ａｌ２Ｏ３及Ｒｕ／ＳｉＯ２催化剂的影响，结果表明，经不同温度焙烧的催化剂样品，其吸附性能有很大差别。随着焙烧温度的升高，金属－载体相互作用增强，导致ＣＯ吸附量减少。Ｒｕ／Ａｌ２Ｏ３吸附的ＣＯ较稳定，而Ｒｕ／ＳｉＯ２吸附的ＣＯ在高温易脱附。各不同ＣＯ吸会态间、多重态更易发生反应。在未焙烧的Ｒｕ／ＳｉＯ２低ＣＯ／Ｈ２反应     

H2-induced CO adsorption and dissociation over Co/Al2O3 catalyst

The activation of adsorbed CO is an important step in CO hydrogenation. The results from TPSR of pre-adsorbed CO with H2 and syngas suggested that the presence of H2 increased the amount of CO adsorption and accelerated CO dissocia-tion. The H2 was adsorbed first, and activated to form H* over metal sites, then reacted with carbonaceous species. The oxygen species for CO2 formation in the presence of hydrogen was mostly OH*, which reacted with adsorbed CO subsequently via CO*+OH* → CO2*+H*; however, the direct CO dissociation was not excluded in CO hydrogenation. The dissociation of C-O bond in the presence of H2 proceeded by a concerted mechanism, which assisted the Boudourd reaction of adsorbed CO onthe surface via CO*+2H* → CH*+OH*. The formation of the surface species (CH) from adsorbed CO proceeded as indicated with the participation of surface hydrogen, was favored in the initial step of the Fischer-Tropsch synthesis.     

铂催化氧还原反应过程中磷酸的影响及抑制磷酸吸附策略

与低温(<100oC)质子交换膜燃料电池相比,磷酸掺杂PBI膜燃料电池可工作于100–200 oC,工作温度的提高有利于提高电极反应动力学速率、增加Pt催化剂对CO等毒物的耐受性,以及简化电池水管理等.然而,磷酸在Pt催化剂表面吸附较强,这将造成Pt一定程度的毒化.基于“第三体效应”,即在Pt表面预吸附某些小分子,可在一定程度上抑制磷酸吸附,然而预吸附分子同时也将占据Pt表面部分活性位点,因而Pt的催化性能最终由两个因素决定：磷酸抑制程度和预吸附分子在Pt表面的覆盖度.
　　本文系统考察了Pt表面预吸附分子覆盖度和预吸附分子链长对其催化氧还原反应(ORR)活性的影响.首先,通过控制预吸附了胺类分子的Pt电极的电位,得到表面具有不同覆盖度的Pt电极,考察了0.1 mol/L H3PO4电解液中Pt电极对ORR的催化活性随预吸附分子覆盖度的变化规律;为分离磷酸吸附和修饰分子吸附本身对Pt催化活性的影响,对比了0.1 mol/L HClO4电解液中Pt电极对ORR的催化活性随预吸附分子覆盖度的变化规律.进一步对比研究了不同链长胺分子——正丁胺(BA)、正辛胺(OA)及十二胺(DA)等作为修饰分子对Pt/C催化剂电催化ORR活性的影响.结果表明,随修饰分子在Pt表面覆盖度提高,在0.1 mol/L HClO4溶液中,由于预吸附分子占据Pt部分活性位,修饰后光滑Pt电极表面的本征活性单调下降;而在0.1 mol/L H3PO4中,修饰后光滑Pt电极表面的ORR活性呈现先升高后降低的趋势,当预吸附分子覆盖度约为20%时,其ORR活性最高,为未修饰的光滑Pt电极表面的1.67倍.这表明预吸附分子有效抑制了磷酸的吸附,且当预吸附分子覆盖度约为20%时,预吸附分子对Pt表面的占据与其抑制磷酸吸附的作用达到最佳平衡点.然而,当修饰分子BA, OA和DA在Pt表面覆盖度分别为38.6%,26.1%和26.1%时, Pt/C在0.1 mol/L H3PO4中的ORR催化活性接近,分别为未经修饰Pt/C电催化剂的1.7,1.8和2.0倍,这表明预吸附分子链长对ORR催化活性影响较小,表面预吸附分子抑制磷酸吸附的策略对Pt/C催化剂也同样适用.同时, Pt/C电极经BA, OA和DA修饰后,其在0.1 mol/L HClO4中的比表面活性分别为未经修饰Pt/C电催化剂的1.0,1.1和1.3倍,与修饰后光滑Pt电极表面本征ORR活性变化规律不一致.然而,与Pt在HClO4电解质中的ORR活性相比, ORR的半波电位仍有大约123 mV的差距,今后还需继续从催化剂的角度,如调控Pt表面的吸附特性,或从创新电解质的角度,如有机磷酸电解质等出发解决磷酸毒化的问题.     

The Surface Chemistry of Water on Fe(100): A Density Functional Theory Study

The formation of water by hydrogenation of atomic oxygen is studied using density functional theory. Atomic oxygen preferentially adsorbs at the four‐fold hollow site, the hydroxyl group prefers the bridge site in a tilted configuration, and water is most stable when adsorbed at the top site with the two O? H bonds parallel to the Fe surface. Water formation by the hydrogenation of oxygen is a highly activated process on the Fe(100) surface, with similar activation energies, in the order of 1.1 eV, for the first and second hydrogen additions. A more favourable route for the addition of the second hydrogen atom involves the disproportionation of hydroxyl groups to form water and adsorbed oxygen. Dissociation of the OH is also likely since the activation energy is similar to that for disproportionation of 0.65 eV. Furthermore, the results show that the dissociation of water on Fe(100) is a non‐activated process: 0.16 eV for the zero‐coverage limit and 0.03 eV when surface oxygen is present. Herein, adsorption energies, structures and vibrational frequencies are presented for several adsorption states at 0.25 ML coverage, as well as the potential energy surface for water formation on Fe(100).