Polymerization of coordinated monomers. V. Polymerization of methyl methacrylate–Lewis acid complexes

The polymerization of the complex of methyl methacrylate with stannic chloride, aluminum trichloride, or boron trifluoride was carried out in toluene solution at several temperatures in the range of 60° to ?78°C by initiation of α,α′-azobisisobutyronicrile or by irradiation with ultraviolet rays. The tacticities of the resulting polymers were determined by NMR spectroscopy. Both the 1:1 and the 2:1 methyl methacrylate–SnCl₄ complexes gave polymers with similar tacticities at the polymerization temperatures above ?60°C. With decreasing temperature below ?60°C, the isotacticity was more favored for the 2:1 complex, whereas the tacticities did not change for the 1:1 complex. On the ESR spectroscopy of the polymerization solution under the irradiation of ultraviolet rays at ?120°C, the 1:1 SnCl₄ complex gave a quintet, while the 2:1 SnCl₄ complex gave both a quintet and a sextet. The sextet became weaker with increasing temperature and disappeared at ?60°C. This behavior of the sextet corresponds to the change of the tacticities of polymer for the 2:1 SnCl₄ complex. An intra–intercomplex addition was suggested for the polymerization of the 2:1 complex, which took a cis-configuration on the basis of its infrared spectra. The sextet can be ascribed to the radical formed by the intracomplex addition reaction, while the quintet can correspond to that formed by the intercomplex addition reaction. The proportion of the intracomplex reaction was estimated to be about 0.25 at ?75°C, and the calculated value of the probability of isotactic diad addition of the intracomplex reaction was found to be almost unity.     

Polymerization of coordinated monomers. III. Copolymerization of acrylonitrile–zinc chloride,methacrylonitrile–zinc chloride or methyl methacrylate–zinc chloride complex with styrene

The 1:1 or 2:1 complex of acrylonitrile, methacrylonitrile, or methyl methacrylate with ZnCl₂ was copolymerized with styrene at the temperature of 0–30°C without any initiator. The structure of the copolymer from methyl methacrylate complex and styrene was examined by NMR spectroscopy. The complexes of acrylonitrile or methacrylonitrile with ZnCl₂ gave a copolymer containing about 50 mole-% styrene units. The complexes of methyl methacrylate yielded an alternating copolymer when the feed molar ratio of methyl methacrylate to styrene was small, but with increasing feed molar ratio the resulting copolymer consisted of about 2 moles of methyl methacrylate per mole of styrene. The formation of a charge-transfer complex of styrene with a monomer coordinated to zinc atom was inferred from the ultraviolet spectra. The regulation of the copolymerization was considered to be effected by the charge-transfer complex. The copolymer resulting from the 2:1 methyl methacrylate–zinc chloride complex had no specific tacticity, whereas the copolymer from the 1:1 complex was richer in coisotacticity than in cosyndiotacticity. The change of the composition of the copolymer and its specific tacticity in the polymerization of the methyl methacrylate complex is related to the structure of the complex.     

Polymerization of coordinated monomers. II. Stereoregulation in the free-radical polymerization of methacrylonitrile–zinc chloride or methacrylonitrile–stannic chloride complexes

The effect of complex formation on stereoregulation in free-radical polymerization was studied. Complexes of methacrylonitrile with ZnCl₂ and SnCl₄ were prepared and their properties and structures examined. The complexes were polymerized by initiation of α,α′-azobisisobutyronitrile or by irradiation with γ-rays from a⁶⁰Co source or ultraviolet rays either in solution or in bulk at various temperatures ranging from ?78 to 100°C. The triad tacticities of the resulting polymethacrylonitrile were determined by converting it to poly(methyl methacrylate) for NMR spectroscopy. The radicals in complexed forms were studied by ESR spectroscopy with the polymerization system in toluene irradiated with ultraviolet rays at ?120°C. The tacticities of the resulting polymers and their dependencies on the polymerization temperature were found to be characteristic of the complex species, i.e., the kind of metal chloride and the stoichiometry, being different from the tacticities and the dependencies, respectively, of the polymer obtained with pure methacrylonitrile. The 2:1 and the 1:1 complexes with SnCl₄ were found to give an eleven-line and a nine-line spectrum, respectively. On the basis of the results of both the tacticities and the ESR spectra, it was estimated that the proportion of the intracomplex reaction was 40%, and that the probabilities of isotactic diad addition of intra- and intercomplex reaction were 0.70 and 0.48, respectively.     

Polymerization of coordinated monomers. I. Stereoregulation in the free-radical polymerization of methyl methacrylate-zinc chloride or methyl methacrylate–stannic chloride complexes

Stereoregulation in free-radical polymerization was studied for the polymerization of the 2:1 or 1:1 complex of methyl methacrylate with ZnCl₂ or SnCl₄. The complexes were polymerized with the use of a free-radical initiator or γ-ray irradiation either in the liquid or solid state at various temperatures ranging from ?196 to 110°C, and the tacticities of the resulting polymers were determined by NMR spectroscopy. The polymers had different and characteristic values of tacticities depending upon the complex species, i.e., the kind of metal chloride and the stoichiometry. The tacticities were found to be independent of the polymerization temperature in both the liquid and solid states, in contrast with the fact that tacticities of the polymer from pure monomer changed markedly with the temperature. A temperature dependence appeared in the polymerization system, which contained more monomer than that corresponding to the 2:1 complex. The effect of the viscosity or the solid phase on the stereoregulation was examined in comparison with the polymerization of a mixture of methyl methacrylate and liquid paraffin. Two possible explanations regarding the stereoregulation mechanism are offered in relation to the structures of the complexes.     

Polymerization of coordinated monomers. XVII. Alternating copolymerization of methyl methacrylate with styrene by boron compounds

By the use of various boron compounds methyl methacrylate and styrene were copolymerized under photoirradiations at ?20°C. The alternately regulating activities of the boron compounds in the copolymerizations were in the following order: boron trichloride > ethylboron dichloride > boron trifluoride > diethylboron chloride ? triethylboron (?0). Boron trichloride and ethylboron dichloride exhibited such high regulating activities that their presence in 1 mol% in the charged methyl methacrylate was sufficient to complete equimolar alternating copolymerization. The alternating copolymerization proceeded in the steady state. The copolymerization rates decreased in the following order: boron trichloride ? ethylboron dichloride > diethylboron chloride ? triethylboron (?0). The cotacticities of methyl methacrylate-centered triads in the resulting copolymers were identical to those prepared with boron trichloride, ethylboron dichloride, and diethylboron chloride. The mechanism of the alternating copolymerization is discussed.     

Polymerization of coordinated monomers. VI. Molecular complex formation of methyl methacrylate coordinated to stannic chloride with styrene or toluene

The equilibrium constants for the complex formation between stannic chloride and methyl methacrylate were determined in n-hexane–toluene solution at 0, ?20, and ?30°C by using the absorption band at 350 nm. Continuous variation plots at ?20°C in n-hexane based on the ¹H-chemical shifts definitely show a 1:1 interaction between the coordinated methyl methacrylate and styrene or toluene. The magnitudes of the shifts for the four groups of protons in methyl methacrylate are found to be in a specific ratio in common with the 1:2 complex–styrene or -toluene system. The equilibrium constants for the ternary molecular complex formation between the 1:2 complex and styrene or toluene were determined in n-hexane in the temperature range ?50 to +20°C by use of the chemical shifts. The concentrations of the complex species in the alternating copolymerization solutions were estimated by use of the equilibrium constants. There is a linear relationship between the enthalpy and the entropy changes for the ternary molecular complex formation, which is governed by the enthalpy factor. The specificity of the interactions indicates a specific time-averaged orientation of benzene ring to the coordinated methyl methacrylate. The effects of the coordination of methyl methacrylate to stannic chloride were discussed on the basis of results of ¹³C-NMR spectroscopy.     

Polymerization of coordinated monomers. XVIII. Sequence distribution in methyl acrylate–styrene copolymers prepared in the presence of zinc chloride

Methyl acrylate and styrene have been copolymerized in the presence of zinc chloride either by photoinitiation or spontaneously. The copolymerization mechanism is investigated by analyses of copolymers composition and monomer sequence distribution. The resulting copolymers are not always alternating, their composition being dependent especially on the monomer feed ratio. Appreciable deviation to higher methyl acrylate unit content from an equimolar composition occurs at monomer feed fractions of methyl acrylate over 0.7. The larger deviation is induced by higher temperature, by photoirradiation, and by greater dilution of the reaction mixture with toluene. The ¹³C-NMR spectrum of the alternating copolymer shows a sharp singlet at the carbonyl region, whereas the spectra of random copolymers prepared by benzoyl peroxide initiation at 60°C show a triplet splitting at the carbonyl carbon region, irrespective of copolymer composition. The relative intensities of the triplet peaks for the random copolymers are in good correspondence to the contents of triad sequences calculated by means of conventional radical copolymerization theory. These results clearly indicate that the carbonyl splitting is caused predominantly by variation of the monomer sequence and not by variation of the stereosequence. The monomer sequence distribution in the copolymers is thus directly and quantitatively measured from the split carbonyl resonance. Although the same triplet splitting appears in the spectra of methyl acrylate–rich copolymers prepared in the presence of zinc chloride at high feed ratios (>0.7) of methyl acrylate, the relative intensities of the split peaks do not fit the sequence distributions of random copolymers calculated by means of the Lewis–Mayo equation. The copolymerization yielding these peculiar sequences and the alternating sequence in the presence of zinc chloride is fully comprehended by a copolymerization mechanism proceeding between two active coordinated monomers, i.e., the ternary molecular complex composed of zinc chloride, methyl methacrylate, and styrene, and the binary molecular complex composed of zinc chloride and methyl methacrylate.     

Polymerization of coordinated monomers. XV. 13C-NMR study on the alternating copolymers of methyl methacrylate with styrene

By the use of various metal halides methyl methacrylate and styrene were copolymerized to produce equimolar alternating sequences and different cotacticities. The ¹³C-NMR spectra of these copolymers were simple in comparison to those of random copolymers because of the fixed monomer sequence which yielded sharply split triplets for carbonyl, methoxy, and quaternary carbons. The relative intensities in these split peaks varied according to the metal halide used. A comparison of the intensities made it possible to obtain clear-cut and quantitative information on the methyl methacrylate-centered triad cotacticity of the copolymers. The spectral assignment with respect to the methoxy carbon was definitely justified by the combined use of partly relaxed Fourier transform and selective decoupling techniques. The spectrum of aromatic C₁ carbon in styrene units also split into three main peaks. From their relative intensities the splitting was attributed to styrene-centered triad cotacticity. The assignment of this carbon was compared with two other assignments made for random copolymers of methyl methacrylate with styrene; they were contradictory, however. Furthermore, an apparent discrepancy was observed between methyl methacrylate-and styrene-centered tactic triads of these alternating copolymers. The origin of this discrepancy suggests a close relationship with the copolymerization mechanism.     

Polymerization of coordinated monomers. XIX. Kinetic study of the alternating copolymerization of methyl methacrylate with styrene by boron trichloride

Alternating copolymerizations of methyl methacrylate with styrene in the presence of boron trichloride at 0°C in 1,2-dichloroethane were carried out by using benzoyl peroxide as an initiator. Conversion increased proportionally with polymerization time, whereas the degree of polymerization was constant irrespective of time. The rate depended linearly on the square root of the concentration of benzoyl peroxide. The equilibrium constants for the formation of the ternary molecular complex composed of methyl methacrylate, styrene, and boron trichloride in 1,2-dichloroethane at ?20, ?10, and +4°C were determined by ¹H-NMR spectroscopy. The concentrations of the ternary molecular complex in the polymerization mixtures were evaluated from the equilibrium constant of the formation. The rate of the alternating copolymerization was proportional to the first order of the concentration of the ternary molecular complex. The distribution of methyl methacrylate-centered triads in the alternating copolymer was different from that of styrene-centered triads. These results can be explained by a mechanism involving the homopolymerization of a ternary molecular complex.     

Polymerization of coordinated monomers. X. Kinetic study of alternating copolymerization of methyl methacrylate and styrene with stannic chloride in dichloroethane

The alternating copolymerization of methyl methacrylate with styrene with the use of stannic chloride was kinetically examined at ?20°C in 1,2-dichloroethane both under photoirradiation and with radical initiator (2:1 tri-n-butylboron-benzoyl peroxide system). At conversions lower than 7%, the conversion increases linearly to the polymerization time, whereas the degree of polymerization is constant irrespective of the polymerization time. The alternating copolymerizations are 1.5 order and the 1.0 order reactions with respect to the ternary molecular complex composed of stannic chloride, methyl methacrylate, and styrene, under photoirradiation and with initiator, respectively. The linear dependences of the rates upon the 0.5 order of the intensity of the incident light and upon the 1.0 order of the concentration of tri-n-butylboron indicate a bimolecular termination. The rate normalized by the 1.5 order of the concentration of the coordinated methyl methacrylate and the rate normalized by the concentration of the coordinated methyl methacrylate are proportional to the 1.5 and 1.0 orders of the charged concentration of styrene, for the copolymerizations under photoirradiation and with initiator, respectively. The kinetic results in the 1,2-dichloroethane solution are quite consistent with those in the toluene solution. The alternating copolymerization mechanism, in which the ternary molecular complex predominantly homopolymerizes as a monomer unit, is confirmed.     

Dielectric study on copolymers in dilute solution. Relaxation behavior of methyl methacrylate–styrene and methyl methacrylate–α-methylstyrene copolymers

Dielectric measurements were made on some methyl methacrylate (MMA)-related polymers in dilute solution, in the frequency range of 1–150 MHz. Effects of the solvent viscosity upon the relaxation behavior were carefully examined. The dielectric relaxation of MMA–styrene copolymers with a high content of MMA units as well as that of the MMA–α-methylstyrene copolymer was little affected by the solvent viscosity. With the aid of Kramers'rate constant for small friction, it was found that their dipolar relaxation is very similar to that caused by the internal rotation of a flexible side-chain. On the other hand, MMA–styrene copolymer with a low content of MMA units showed a diffusion-controlled relaxation process, which can be interpreted in terms of Kramers' theory for large friction. In the latter case, the dipolar relaxation appears to reflect a molecular motion such as sweeping out solvent molecules. These results indicate that it is not the dipole itself but its environment, or rather the local molecular structure containing dipoles, that principally controls the relaxation process. On this basis, we propose a criterion, for quantitatively distinguishing the two relaxation mechanisms from each other.     

Polymerization of coordinated monomers VII. A kinetic study on the alternating copolymerization of methyl methacrylate with styrene using stannic chloride

The alternating copolymerization of methyl methacrylate with styrene in the presence of stannic chloride at ?50°C in toluene was kinetically investigated both under photoirradiation and with the tri-n-butylboron-benzoyl peroxide initiator. The concentrations of the binary and ternary molecular complexes in the copolymerization solution were estimated by use of the equilibrium constants. The rates are found to be proportional to the 1.5th and 1.0th orders of the concentration of the ternary molecular complex composed of stannic chloride, methyl methacrylate, and styrene, under photoirradiation and with initiator, respectively. The conversion increases proportionally with the polymerization time, while the degree of polymerization is constant irrespective of the time. The rates depend linearly upon the square root of the intensity of the incident light and upon the concentration of tri-n-butylboron, respectively. The alternating copolymerization is confirmed experimentally to precede the homopolymerization of the monomer charged in large excess both under photoirradiation and with initiator. The kinetic results indicate consistently that the alternating copolymerization proceeds through the homopolymerization of the ternary molecular complex in the steady state with a bimolecular termination. Both the conventional radical mechanism and the double complex mechanism are unsuitable for the present alternating copolymerization.     

Selective initiation of nonconjugated dienes containing electron donor–electron acceptor systems. IV. Polymerization of vinyl ether–styrene monomers

Three isomeric nonconjugated dienes, o-, m- and p-(2-vinyloxyethoxy)styrenes, were selectively polymerized by anionic or radical initiators through the styryl double bond while leaving the vinyl ether moiety intact. The anionic-initiated polymeric products are of high molecular weight and narrow molecular weight distribution as characterized by membrane osmometry and gel-permeation chromatography, respectively. These polymers were subsequently crosslinked by cationic initiators via the vinyl ether moiety on the polymer side chains. Acid-catalyzed hydrolysis of the poly(2-vinyloxyethoxy)styrenes yielded their respective hydroxy-containing polymers, polyvinylphenoxyethanols. The latter were physically and spectroscopically identical to authentic samples prepared by radical polymerization of the corresponding vinylphenoxyethanols, which, in turn, were synthesized by hydrolysis of the (2-vinyloxyethoxy)styrenes. The polyvinylphenoxyethanols were shown to undergo many chemical transformations, such as esterification with 3,5-dinitrobenzoyl chloride, cyanoethylation, and urethane formation.     

Alternating copolymerization of polar vinyl monomers in the presence of zinc chloride. III. NMR study of methyl methacrylate–styrene copolymer

The copolymer composition curve of the methyl methacrylate–styrene copolymer obtained by the copolymerization in the presence of ZnCl₂ has more alternating tendency than that of ordinary methyl methacrylate–styrene copolymer obtained by radical copolymerization. The fine structure of the copolymer was examined by NMR, and the mechanism of the propagation step of the copolymerization in the presence of ZnCl₂, which was proposed in the first report of this series, was verified.     

Polymerization of coordinated monomers. XVI. Stereoregulation in the alternating copolymerization of methyl methacrylate with styrene in the presence of metal halides

Triad cotacticities of alternating copolymers of methyl methacrylate with styrene prepared in the presence of zinc chloride, ethylaluminium sesquichloride, and ethylboron dichloride are investigated from the mechanistic point of view by means of ¹H- and ¹³C-NMR. The cotacticities from ¹H-NMR spectra are obtained accurately by using α-d-styrene in the place of styrene and by measuring the spectra on the copolymer in o-dichlorobenzene at 170°C. The relative intensities of three peaks of the splitting signal for the methoxy protons in the nonalternating copolymers obtained by the use of benzoyl peroxide in the absence of metal halides agree well with the cotacticity distribution calculated theoretically by the Lewis-Mayo mechanism with the stereoregulation following Bernoullian statistics. The splitting signals in the ¹H- and ¹³C-NMR spectra of the alternating copolymers prepared in the presence of metal halides cannot be explained by the same mechanism. The relative intensities of three peaks of the splitting signals for the methoxy protons and for the carbonyl carbon in the methyl methacrylate unit (the contents of cotactic triads centered by the methyl methacrylate unit) are not equal to those for the aromatic C₁ carbon in the styrene unit (the contents of cotactic triads centered by styrene unit). The value of f²Y - 4fxfz is not equal to zero, where fx, fy, and fz are the cosyndiotactic, coheterotactic, and coisotactic triad contents, respectively, in the alternating copolymer. Copolymers obtained in the presence of zinc chloride are not exactly equimolar alternating but always contain a methyl methacrylate unit in excess, and the relative intensities of the three peaks for the aromatic C₁ carbon change with the copolymer composition. These results are explained by a proposed mechanism: the alternating copolymerization proceeds through the homopolymerization of a ternary molecular complex composed of a metal halide, methyl methacrylate, and styrene, accompanied with the stereoregulation following first-order Markovian statistics; the increase of methyl methacrylate content in the copolymer prepared in the presence of zinc chloride is caused by the participation of the binary molecular complex composed of a metal halide and methyl methacrylate in addition to the ternary molecular complex.     

Copolymerization of eight-membered ring-opening allylic sulfide lactone and disulfide monomers with methyl methacrylate and styrene

Apparent reactivity ratios and detailed NMR analysis of copolymerizations of eight membered ring-opening allylic sulfide monomers; 3-methylene-1,5-oxathiocan-2-one 2 and 2,2,4-trimethyl-7-methylene-1,5-dithiocane 5 with methyl methacrylate and styrene are presented. The activated double bond of 2 and unactivated double bond and additional methyl substituents of 5 were found to have a profound affect on reactivity. The copolymerization rates were analyzed based on the lumped parameter k_p(f/k_t)^0.5, which was estimated as a function of monomer composition in the feed.     

Polymerization of vinyl monomers by diphenylsulfone–potassium complexes

Diphenylsulfone (DPSO₂) was found to react with an equimolar amount of potassium in tetrahydrofuran (THF), dimethoxyethane (DME), or diglyme (DG) at reflux or an elevated temperature to yield a reddish-black solution, giving an electron spin resonance (ESR) signal. The signal was attributed to the formation of relatively labile DPSO₂ anion radical. The apparent effects of solvents on the reactivity of DPSO₂ with potassium depended on the polarities and the solvation powers: benzene ? toluene ? dioxane ? tetrahydrofuran < monoglyme < diglyme. The monopotassium complex was found to react further with another molecular amount of the metal to yield a dark blue solution giving no ESR signal. The monopotassium complex initiated the polymerization of acrylonitrile (AN). It did not, however, initiate the polymerization of methyl methacrylate (MMA), styrene (St), or isoprene (IP). The active species of the monopotassium complex that initiated the polymerization of AN was found from analyses of the reaction products and the infrared spectrum of oily oligomer of AN obtained by the complex to be potassium benzenesulfinate. The dipotassium complex was found to initiate the polymerization of MMA, St, IP and AN. The active species of the dipotassium complex that initiated the polymerization of MMA, St, or IP was found from analyses of the reaction products and the infrared spectrum of the oily oligomer of MMA obtained by the complex to be phenyl potassium.     

Copolymerization of styrene and methyl methacrylate. Reactivity ratios from conversion–composition data

A method for the determination of reactivity ratios from conversion–composition data has been outlined. The conversion–composition changes during the copolymerization of styrene (M₁) and methyl methacrylate (M₂) have been studied at 60°C. By a method of graphical intersection, the integrated form of Skeist's equation has been used to determine the reactivity ratios (r₁ = 0.54 ± 0.02 and r₂ = 0.50 ± 0.06) in reasonably good agreement with values reported in the literature. The area of intersection was used as a measure of the precision of the data.     

Polymerization of coordinated monomers. XIV. Systematic deviations from alternating regulation in copolymerization of methyl methacrylate with styrene in the presence of metal halides

Methyl methacrylate (MMA) and styrene (St) copolymerize in the presence of zinc chloride at 3°C under photoirradiation. The contents of methyl methacrylate in the copolymers obtained at a [ZnCl₂]/[MMA] molar ratio of 0.4 are systematically larger than 53 mole %, which is the limiting value at a small feed ratio of methyl methacrylate. The resulting copolymers are confirmed as the sole products and not the mixtures by thin layer chromatography. The effect of dilution of the monomer feed mixture with toluene on copolymer composition suggests that it depends chiefly on the feed concentration of styrene and hardly at all on monomer feed ratios. Copolymerizations are also conducted in the presence of stannic chloride at ?17°C under photoirradiation and in the presence of ethylaluminium sesquichloride at 0°C with spontaneous initiation. The contents of methyl methacrylate in both copolymers obtained at feed ratios lower than 60 mole % almost correspond to the 1:1 alternating copolymer and increase systematically with higher feed ratios. The systematic deviations of copolymer composition obtained in the presence of metal halides are reasonably interpreted by the participation of the binary molecular complex composed of metal halide and methyl methacrylate in the polymerization of the ternary molecular complex composed of metal halide, methyl methacrylate, and styrene.