ssDNA/十八酸修饰碳糊电极的制备及伏安法表征

将石墨粉与十八酸在80 ℃下混合制成表面富含—COOH的基底碳糊电极(SA/CPE), 然后在活化剂N-羟基琥珀酰亚胺(NHS)和1-乙基-3-(3-二甲基氨丙基)碳二亚胺盐酸盐(EDC)存在下将ssDNA固定到电极表面制备ssDNA修饰电极(ssDNA/SA/CPE). 以亚甲基蓝(MB)为指示剂, 用循环伏安法对SA/CPE和ssDNA/SA/CPE进行电化学表征, 发现其在ssDNA/SA/CPE上较在SA/CPE上的氧化峰电流(i_pa)和还原峰电流(i_pc)分别增大1.9倍和1.7倍, 式电势(E_f)负移8 mV. 把ssDNA/SA/CPE放在互补ssDNA溶液中杂交后, MB的i_pa 和i_pc较在SA/CPE上分别增大1.0倍和0.8倍, E_f负移18 mV. 用0.5 mol/L 的NaOH溶液冲洗使电极表面杂交而成的dsDNA变性洗脱, MB的伏安信号几乎与在ssDNA/SA/CPE上一样. i_pc与SA/CPE上固定的ssDNA质量在1.0×10^－7～5.0×10^－6 g范围内成线性关系, 检测限为2.0×10^－9 g (S/N＝3). 这种既廉价又灵敏的电化学生物传感器有望在转基因植物产品检测研究中得到应用.     

DNA修饰碳纳米管电极对DNA与亚甲基蓝相互作用的研究

通过羧基化的多壁碳纳米管（MWNTs）电极表面的-CO0H与DNA末端的-NH2,在N-羟基琥珀酰亚胺（NHS）和1-乙基一3-（3-二甲基氨丙基）碳二亚胺盐酸盐（EDC）活化作用下,制备了DNA共价修饰MWNTs电极。采用循环伏安法系统研究了崮定在MWNTs电极表面的DNA与亚甲基蓝（MB）之间的相互作用。实验结果表明：在20～200mV·s^-1范围内,MB在DNA修饰MWNTs电极上的氧化还原过程为表面控制过程;在pH5．1～7．6范围内,MB在DNA修饰MWNTs电极上的峰电位随pH的增加向负方向移动。     

玻碳电极吸附伏安法测定痕量硫化物的研究

研究了利用玻碳电极吸附伏安法测定痕量硫化物的新方法。在含高铁离子的酸性溶液中,硫化物与对-氨基苯二甲基盐酸盐(p-ADAD)反应生成亚甲基蓝,采用线性扫描伏安法亚甲基蓝于-0.30 V(vs.SCE)在玻碳电极上出现灵敏的还原峰,峰电流与S2-浓度在0～25μg/mL范围内呈良好的线性关系。优化了实验条件,研究了电极反应机理。该方法具有灵敏、简便、快速、避免汞污染等特点。已成功用于多种水样中痕量硫化物的测定,回收率为98.0%～104.6%,结果令人满意。     

DNA共价结合在化学修饰云母片上的AFM研究

原子力显微镜(AFM)自1986年发明以来,已经成为生物学研究领域中的一个有效工具,尤其在核酸及其它生物大分子结构方面的应用已成为普遍关注的热点.原子力显微镜要求基底达到原子级平整,硅片和玻璃表面的起伏很大,因而原子级平整的云母具有重要的价值.     

无修饰碳糊电极为工作电极-差分脉冲伏安法测定DNA中4种碱基的含量

取健康人尿样2.5mL,加入高氯酸(1+9)溶液4.5mL,涡旋振荡30min,离心,取上清液用100g·L-1的氢氧化钠溶液调节其酸度至4.5,以质量比为5∶1的石墨粉/硅油Ⅲ制备的碳糊电极作为工作电极,以pH 4.5的0.1mol·L-1乙酸盐缓冲溶液为电解质,采用差分脉冲伏安法测定上清液中腺嘌呤、鸟嘌呤、胞嘧啶和胸腺嘧啶的含量。结果表明:4种碱基的浓度分别在一定范围内与其峰电流呈线性关系,检出限(3S/N)依次为0.090,0.050,17,2.8μmol·L-1。按标准加入法进行加标回收试验,测得回收率在92.5%～109%之间,测定值的相对标准偏差(n=5)在0.90%～4.3%之间。     

聚甲基蓝修饰电极的制备及对多巴胺的测定

研究了聚甲基蓝修饰电极的制备及其多巴胺在聚甲基蓝修饰电极上的循环伏安特性,建立了循环伏安法测定多巴胺的新方法。在pH7.0磷酸盐缓冲溶液中,峰电流与多巴胺浓度在8.0×10-7～5.0×10-4mol L范围内呈良好的线性关系,检出限为5.0×10-8mol L。已用于药剂中多巴胺的测定。     

聚次甲基蓝修饰玻碳电极测定叶酸

利用循环伏安法将次甲基蓝修饰到玻碳电极表面,制备了聚次甲蓝修饰电极(PMB/GCE),并研究了此电极的化学性质及对叶酸的电化学响应特性.在磷酸盐缓冲液中PMB/GCE电极对叶酸有良好的催化作用并出现一个灵敏的还原峰,用循环伏安法测得峰电流与叶酸的浓度在0.1×10-3～2.9×10 -3 mol/L范围内呈良好线性关系...     

DNA/聚(3,4-乙烯基二氧噻吩)修饰电极的制备及其用于亚硝酸根的电化学行为及测定研究

采用恒电流和电沉积两步法制备了脱氧核糖核酸-聚(3,4-乙烯基二氧噻吩)(DNA-PEDOT)复合膜修饰玻碳电极。用电化学阻抗法(EIS)和循环伏安法(CV)表征了不同修饰电极的修饰可行性和表面的电子传递能力。结果表明,DNA可以牢固地结合在PEDOT膜上,并能改善PEDOT膜的性质。研究了NO2-在DNA-PEDOT修饰电极上的电化学行为,提出了一种新的检测NO2-的电化学方法。在0.1 mol/L pH7.0的磷酸盐缓冲溶液(PBS)中,NO2-在DNA-PEDOT修饰电极上于0.88 V左右出现1个较好的氧化峰,考察了该氧化峰的性质及其影响因素。示差脉冲伏安法(DPV)的结果表明,NO2-的DPV氧化峰电流与其浓度在0.3~1.0、1.0~20、20~100μmol/L 3个范围内呈良好的线性关系,检出限(S/N=3)为60 nmol/L,并考察了可能存在的干扰物质对测定的影响。结果显示,该复合膜修饰电极对NO2-的检测具有良好的稳定性和选择性。将其用于实际样品的检测,结果满意。     

DNA-纳米多孔羟基磷灰石修饰电极用于研究DNA与亚甲基蓝的相互作用

利用溶胶-凝胶法将具有优良生物相容性和独特吸附性的羟基磷灰石(HAp)修饰在玻碳电极上形成纳米多孔薄膜. 电化学实验结果证明该纳米多孔羟基磷灰石薄膜能有效地将双链DNA吸附于其表面. 采用循环伏安法系统研究了固定在HAp薄膜上的DNA与亚甲基蓝(MB)之间的相互作用. 实验结果表明, 在20～200 mV•s^－1扫描速度范围内该电极反应过程系表面反应控制; 在pH 6.0～7.4范围内, MB在DNA修饰电极上的峰电位随pH的增加而向负方向移动; 当磷酸盐缓冲溶液中的离子强度小于59 mmol•L^－1时, MB与DNA之间为静电作用, 当离子强度大于59 mmol•L^－1时, 二者之间既有静电作用, 也有部分嵌入作用. 根据Langmuir吸附公式, 得出MB与DNA之间的结合常数为4.2×10⁴ mol^－1•L.     

普鲁士蓝膜修饰电极循环伏安行为的研究

本文研究普鲁士蓝(PB)膜修饰电极的循环伏安行为,结果表明,膜中电活性中心间的相互作用导致PB膜电极的伏安行为偏离理想表面波.用有限扩散边界模型解释了高电位扫速下膜电极的伏安行为.在含钾离子的电解质溶液中测得PB膜中电荷传输扩散系数为10~(-9)～10~(-11)cm~2/s.     

Nano-ZnO/Chitosan Composite Film Modified Electrode for Voltammetric Detection of DNA Hybridization

Abstract

A sensitive electrochemical DNA biosensor based on nano-ZnO/chitosan composite matrix for DNA hybridization detection was developed. The Nano-ZnO was synthesized by the hydrothermal method and dispersed in chitosan, which was used to fabricate the modification of the glassy carbon electrode (GCE) surface. The ZnO/chitosan-modified electrode exhibited good biocompatibility and excellent electrochemical conductivity. The hybridization detection was monitored with differential pulse voltammetry (DPV) measurement using methylene blue (MB) as an indicator. The established biosensor can effectively discriminate complementary target sequence and two-base-mismatched sequence, with a detection limit of 1.09 × 10^?11 mol L^?1 of complementary target.     

Voltammetric Detection of the DNA Interaction with Toluidine Blue

Binding reactions of toluidine blue (TB) with herring fish DNA in pH 6.0 Britton–Robinson (B–R) buffer solution have been investigated by cyclic voltammetry and linear‐sweep voltammetry at a glassy carbon electrode. TB has a couple of well‐defined redox peaks. The addition of DNA into the TB solution resulted in the decrease of the redox‐peak currents and the shift negatively of the anodic peak potential. The values of the electrochemical parameters such as the electron number of the electrochemical reaction, the electron transfer coefficient and the electrochemical reaction standard rate constant in the absence and presence of DNA, as well as the values of binding constant and binding ratio of DNA with TB were obtained. Almost unchanged values of the electrochemical parameters in the absence and presence of DNA show that nonelectroactive complexes were formed when TB interacted with DNA. DNA concentration can be determined by the decrease of the peak current of TB. The binding mode of TB with DNA was discussed.     

A Novel DNA Probe Based on Molecularly Imprinted Polymer Modified Electrode for the Electrochemical Monitoring of DNA

A DNA probe that was based on methylene blue (MB) imprinted polyvinyl pyridine polymer (MIP) modified carbon paste electrodes were developed for the first time for electrochemical monitoring of DNA. Probes were built up by adsorbing MB onto modified electrodes prior to DNA immobilization. It was shown that DNA strongly immobilizes on MIP modified electrodes when MB was adsorbed in advance of DNA immobilization. The performance of the MB imprinted polymer modified carbon paste electrodes (MIP‐CPE) to rebind the template molecule (MB) were compared to those of control polymer modified (non‐imprinted polymer NIP‐CPE) and bare (CPE) electrodes. Electrochemical signal resulting from the oxidation of guanine moiety of the immobilized probe DNA was high enough on the constructed platform, implicating that probes of this kind could be favorably used for DNA analysis. These probes exhibited high selectivity for its complementary DNA sequences (target). HBV‐DNA hybridization was studied to evaluate the selectivity of the probes for complementary, non‐complementary and mismatch sequences. The detection limit of the probe for the target DNA was 8.72 µg/mL (1.38 µM), which was better than those attained by some earlier DNA sensor studies.     

Voltammetric determination of DNA hybridization using methylene blue and self-assembled alkanethiol monolayer on gold electrodes

An electrochemical DNA biosensor based on the recognition of single stranded DNA (ssDNA) by hybridization detection with immobilized complementary DNA oligonucleotides is presented. DNA and oligonucleotides were covalently attached through free amines on the DNA bases using N-hydroxysulfosuccinimide (NHS) and N-(3-dimethylamino)propyl-N′-ethylcarbodiimide hydrochloride (EDC) onto a carboxylate terminated alkanethiol self-assembled monolayers (SAM) preformed on a gold electrode (AuE). Differential pulse voltammetry (DPV) was used to investigate the surface coverage and molecular orientation of the immobilized DNA molecules. The covalently immobilized probe could selectively hybridize with the target DNA to form a hybrid on the surface despite the bases being attached to the SAM. The changes in the peak currents of methylene blue (MB), an electroactive label, were observed upon hybridization of probe with the target. Peak currents were found to increase in the following order: hybrid-modified AuE, mismatched hybrid-modified AuE, and the probe-modified AuE which indicates the MB signal is determined by the extent of exposed bases. Control experiments were performed using a non-complementary DNA sequence. The effect of the DNA target concentration on the hybridization signal was also studied. The interaction of MB with inosine substituted probes was investigated. Performance characteristics of the sensor are described.     

Voltammetric Study of Methylene Blue at Thiol SAMs‐Modified Gold Electrodes

The voltammetric behavior of methylene blue (MB) at thiol self‐assembled monolayers modified gold electrodes (SAMs/Au) has been investigated. MB exhibited a redox peak at about ?0.35 V (vs.SCE) in alkaline solution at bare gold electrodes. When the gold electrodes were modified with thiol SAMs, the peak grew due to the accumulation of MB at SAMs. With the solution pH rising, more MB was accumulated, hence the peak height increased, which differed from that at bare gold electrodes. The electrode process at SAMs/Au featured the characteristics of adsorption and/or electrode reaction controlled. The enhancing action of glutathione monolayer (GSH SAM), 3‐mercaptopropionic acid monolayer (3MPA SAM) and other thiol SAMs was compared. Among these, GSH SAM made the MB peak increase more. At GSH SAM/Au, the peak height varied linearly with MB concentration over the range of 2 μM to 400 μM. So this can be developed for the determination of MB and studies concerned. The accumulation behavior caused by GSH SAM and native fish sperm dsDNA was compared. The interaction between DNA and MB was also discussed under this condition.     

Sensitive and Selective Detection of Dopamine Using a DNA Immobilized Ethylenedidamine/Polyglutamic Modified Electrode

DNA was attached on the surface of an ethylenedidamine/polyglutamic(En/PGA) modified glassy carbon electrode (GCE) to create a novel voltammetric sensor (DNA/En/PGA/GCE) for dopamine (DA). This modified electrode exhibited a linear voltammetric response for DA in the range from 1.0×10^?7 mol L^?1 to 1×10^?5 mol L^?1, with a detection limit of 2×10^?8 mol L^?1. The detection of DA was found to be unaffected by the presence of ascorbic acid, uric acid, serotonin and folic acid. The method proposed was applied to detect DA in pharmaceutical dosage and human blood serum with good satisfactory results.     

掺杂硒修饰碳糊电极伏安法测定对乙酰氨基酚

采用循环伏安法制备了掺杂硒修饰碳糊电极,用循环伏安法和差分脉冲伏安法研究了对乙酰氨基酚在掺杂硒修饰碳糊电极上的电化学行为,建立了掺杂硒修饰碳糊电极测定对乙酰氨基酚的电化学方法。在pH 4.6的0.1mol·L-1乙酸-乙酸钠缓冲溶液中,对乙酰氨基酚在+0.61V呈现一个灵敏的氧化峰。对乙酰氨基酚的浓度在6.0×10-7~1.5×10-4 mol·L-1范围内与其氧化峰电流呈线性关系,检出限(3s/k)为2.8×10-7 mol·L-1。方法用于药品中对乙酰氨基酚的测定,测定结果与药典法测定值相符,测定值的相对标准偏差(n=5)在2.1%~2.5%之间。     

用盐酸阿霉素作为嵌入剂石墨电极伏安法识别测定DNA片段的研究

用盐酸阿霉素作为嵌入剂石墨电极伏安法识别测定ＤＮＡ片段的研究方禹之,刘盛辉,何品刚（华东师范大学化学系,上海,２０００６２）关键词ＤＮＡ,嵌入剂,盐酸阿霉素,伏安法核酸分子杂交技术是近年来发展起来的检测ＤＮＡ分子的一种重要手段,目前主要采用的放射性同...     

Voltammetric Behavior of Semicarbazide at Graphene Modified Electrode and Application to Detection

Herein voltammetric behaviors of semicarbazide (SEM) are investigated by employing a graphene modified working electrode, which displays attractive electroanalytical properties. In the acetate buffer solution of pH 4.00, there is a well‐defined oxidative peak of SEM, attributing to the irreversible and adsorption‐controlled electrode reaction with 2 electrons participation. The values of apparent heterogeneous electron transfer rate constant k′_s with the redox are 0.0061 s^?1 and 0.0009 s^?1, respectively, for two scan rate section. After the experimental parameters, which influence the voltammetric responses of SEM, including supporting electrolyte, pH, accumulation time and accumulation potential, etc., are optimized, it is found that the anodic peak current of SEM is proportional to its concentration in the range of 4 ‐ 40 μmol/L with a detection limit of 1 μmol/L (S/N = 3). Then, an electrochemical method for detecting SEM quantitatively is developed successfully. The concentrations of SEM in fortified tap water samples are tested with satisfactory recovery, indicating that the novel method is strongly promising in the environmental monitoring application.