Formation of nano-crystalline and amorphous phases on the surface of stainless steel by Nd:YAG pulsed laser irradiation

Thin surface layers consisting of nano-crystalline and amorphous phases on the surface of stainless steel have been attained under the Nd:YAG pulsed laser irradiation. The phases and microstructures were investigated by X-ray diffraction (XRD) and high resolution transmission electron microscope (HRTEM). The phase compositions of the surface determined by XRD were α-Fe (ferrite) and γ-Fe (austenite) or only γ-Fe in the near surface region on the bases of the different laser power densities. The nano-crystalline grains with sizes of 4-100 nm could result from high cooling rate and crystallization in amorphous region by homogeneous and heterogeneous nucleation. The formation of the amorphous phase was attributed to the higher cooling rates.     

Accumulation morphology on the surface of stainless steel irradiated by a nanosecond Nd:YAG pulsed laser

In this study, results in the irradiation of stainless steel AISI 304 in air with nanosecond laser pulses at laser irradiation power density 4×10⁷ W/cm² are reported. Laser processing parameters, such as wavelengths 532 and 1064 nm, pulse duration 20 ns and repetition rate 10 Hz were used. It is shown that the surface morphology of the stainless steel is related to the number of pulses applied to the same spot. The following surface morphological changes were observed: (i) occurrence of the micro-grains microstructures at wavelengths 532 and 1064 nm after 10 000 pulses irradiation and (ii) occurrence of vermiform-like microstructures at wavelength 1064 nm after 1000 pulses irradiation. Generally, it is concluded that irradiation due to several consecutive pulses caused significant damage and enhanced the stainless steel surface roughness.     

Microstructure evolution on the surface of stainless steel by Nd:YAG pulsed laser irradiation

New structure phenomena with the grain sizes of 60 nm to 1 μm would be expected on the stainless steel surface by Nd:YAG pulsed laser irradiation. Nano-structures with various shapes and sizes were formed mainly during the solidification and most shapes of particles were diversiform according to different distances from the center of the spot. The morphologies were of equiaxed nano-particles and faceted hexagons. The surface re-solidification velocities have been estimated according to the numeral simulation of the thermal conditions. It was proved by the XRD that they were mainly consisted of γ-Fe and manganese oxides. The XPS results confirmed the EDS results that on the surface the alloy elemental composition in the outermost layer were rich in Mn and poor in Fe and in reverse in the center of the laser spot. Through observation of morphologies grown on the laser irradiated surfaces, direct evidence of growth mode transition from a continuous form to a lateral form was provided in one laser spot.     

高平均功率六棒串接脉冲Nd:YAG激光器

报道了一种腔内六棒串接的脉冲Nd:YAG激光器。采用44矩阵对晶体棒失调角度对谐振腔光轴的影响进行了理论分析,给出了六棒串接脉冲激光器中晶体棒失调角度的允许范围。在串接实验中,谐振腔采用对称平平腔结构,通过调整每根晶体棒的失调角度到允许范围内,实现了六棒串接脉冲Nd:YAG激光器。在输入电功率86 kW,占空比17%时,获得了平均功率3 018 W的脉冲激光输出,峰值功率17.75 kW,最高单脉冲能量为66 J,光束参数乘积为26.3 mmmrad,电光转换效率3.5%,长时间工作不稳定性小于2%。     

High power Nd:YAG slab laser sidepumped by diode laser array

ＨｉｇｈｐｏｗｅｒＮｄ：ＹＡＧｓｌａｂｌａｓｅｒｓｉｄｅｐｕｍｐｅｄｂｙｄｉｏｄｅｌａｓｅｒａｒｒａｙＣＨＥＮＹｏｕｍｉｎｇ；ＺＨＯＵＦｕｚｈｅｎｇ；ＨＵＷｅｎｔａｏ；ＬＩＺｈｉｓｈｅｎ；ＹＡＮＧＸｉａｎｇｃｈｕｎ；ＷａｎｇＺｈｉｊｉａｎｇ（Ｓｈａｎ...     

Experimental study of electro-optical Q-switched pulsed Nd:YAG laser

We report the specification of a compact and stable side diode-pumped Q-switched pulsed Nd:YAG laser. We experimentally study and compare the performance of the pulsed Nd:YAG laser in the free-running and Q-switched modes at different pulse repetition rates from 1 Hz to 100 Hz. The laser output energy is stabilized by using a special configuration of the optical resonator. In this laser, an unsymmetrical concave-concave resonator is used and this structure helps the mode volume to be nearly fixed when the pulse repetition rate is increased. According to the experimental results in the Q-switched operation, the laser output energy is nearly constant around 70 mJ with an FWHM pulse width of 7 ns at 100 Hz. The optical-to-optical conversion efficiency in the Q-switched regime is 17.5%.     

355 nm nanosecond pulsed Nd:YAG laser profile measurement, metal thin film ablation and thermal simulation

Laser ablation of nickel, gold and copper thin film on glass substrates has been investigated using a nanosecond pulsed Nd:YAG laser operating at 355 nm in air with a Gaussian intensity profile. The exact beam profile was measured through mechanical scanning with a photodiode. A small beam defect was observed, which can affect the machining performance at higher pulse energies. The ablation thresholds of the films were calculated from the crater diameter values. The effect of the pulse repetition rate and the film thickness was also studied. At high pulse repetition rates heat accumulation was observed and the ablation threshold decreased with the film thickness. Both cases resulted in higher diameters.     

Microstructure and microhardness analysis of the hexagonal oxides formed on the surface of the AISI 304 stainless steel after Nd:YAG pulsed laser surface melting

The laser surface melting (LSM) technique was adopted to modify the surface layer microstructure of the AISI 304 stainless steel in this paper. The results showed that the hexagonal morphologies have been successfully fabricated on the surface after LSM. These hexagons had side lengths of about 0.5-1 μm and were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), field emission scanning electron microscope (FESEM) and high resolution transmission electron microscope (HRTEM). It was proved by the XRD that the stainless steel surface mainly consisted of γ-Fe, Cr₂O₃, Fe₂O₃ and some manganese oxides. The FESEM micrographs showed that the hexagonal oxides were regular hexagons in geometry. The HRTEM micrographs also indicated the presence of the hexagons on the surface of the stainless steel. The spacing values were calculated from the HRTEM micrograph and the SAED pattern, and the hexagonal oxide phases determined by these spacing values were consistent with those verified by the XRD. After LSM, the microhardness of the stainless steel was significantly improved.     

A parametric study of pulsed Nd:YAG laser micro-drilling of gamma-titanium aluminide

In the present research, Nd:YAG laser micro-drilling of gamma-titanium aluminide, a new material which has performed well in laboratory tests as well as in different fields of engineering, is studied. The effect of different process parameters in the optimization of the process is investigated. The aspects considered are the hole circularity at exit and the hole taper of the drilled hole. Lamp current, pulse frequency, air pressure and thickness of the job are selected as independent process variables. The central composite design (CCD) technique based on response surface methodology (RSM) is employed to plan the experiments to achieve optimum responses with a reduced number of experiments.     

1.15 kW连续波全固态Nd:YAG激光器

研制了五组双线二极管列阵侧面泵浦Nd: YAG棒的高效率、高功率激光头。将一块90° 石英旋光片插入两个这样的激光头中间并置入热近非稳对称平平腔，产生了1157 W高光束质量（M2 ~ 39）1064 nm连续波输出，据我们所知，这是侧面泵浦双棒Nd: YAG激光器产生的最高功率。     

透明Nd:YAG激光陶瓷的研究与应用进展

综述了近年来,特别是近两年来国内外透明Nd:YAG激光陶瓷的研究与应用情况,重点对我国的透明Nd:YAG激光陶瓷研究近况进行了分析,指出了透明Nd:YAG激光陶瓷是目前陶瓷研究的热点。提出了透明Nd:YAG激光陶瓷研究中尚存在的问题和我国在此领域中与国外研究的巨大差距。分析指出:我国研究透明Nd:YAG激光陶瓷的各个院所之间,应该强强联合,优势互补,对该领域的理论和制备工艺进行更为深入的研究。     

Potential of Nd:YAG pulsed laser deposition method for coated conductor production

A Nd:YAG laser is environmentally safe and economical with no poisonous or hazardous gases and no expensive gases. We prepared Y123 films by using the fourth harmonic Nd:YAG pulsed laser deposition (PLD) method and optimized the deposition conditions on MgO single crystalline substrates and IBAD-MgO substrates for Y123 coated conductor. We found that the optimal deposition conditions acquired bi-axially aligned Y123 films on both substrates with T_c ∼ 90 K and J_c > 1 MA/cm² at 77 K in self-field. For obtaining high I_c, we fabricated thick Y123 films on both substrates and the maximum I_c per 1 cm in width reached 186 A/cm-width on the IBAD-MgO substrate. Interestingly, there were no a-axis oriented grains within the films up to 1.8 μm thick. This might be an especial feature of the Nd:YAG-PLD method. We believe that the Nd:YAG-PLD method is promising method for RE123 coated conductor production.     

Nd：YAG激光器中的自锁模

本文报道在Nd:YAG激光器中首次获得的自锁模脉冲序列.自锁模是由于Nd:YAG棒中的自相位调制引起的.在主被动对撞锁模运转情况下,自锁模对脉冲波形有较大的影响.     

Surface modifications of AISI 1045 steel created by high intensity 1064 and 532 nm picosecond Nd:YAG laser pulses

Interaction of Nd:YAG laser, operating at 1064 or 532 nm wavelength and a pulse duration of 40 ps, with AISI 1045 steel was studied. Surface damage thresholds were estimated to be 0.30 and 0.16 J/cm² at the wavelengths of 1064 and 532 nm, respectively. The steel surface modification was studied at the laser energy density of 10.3 J/cm² (at 1064 nm) and 5.4 J/cm² (at 532 nm). The energy absorbed from Nd:YAG laser beam is partially converted to thermal energy, which generates a series of effects, such as melting, vaporization of the molten material, shock waves, etc. The following AISI 1045 steel surface morphological changes and processes were observed: (i) both laser wavelengths cause damage of the steel in the central zone of irradiated area; (ii) appearance of a hydrodynamic feature in the form of resolidified droplets of the material in the surrounding outer zone with 1064 nm laser wavelength; (iii) appearance of periodic surface structures, at micro- and nano-level, with the 532 nm wavelength and, (iv) development of plasma in front of the target. Generally, interaction of laser beam with the AISI 1045 steel (at 1064 and 532 nm) results in a near-instantaneous creation of damage, meaning that large steel surfaces can be processed in short time.     

Effect of XeCl laser irradiation on the defect structure of Nd:YAG crystals

This paper presents the effect of XeCl laser irradiation on Nd:YAG single crystal samples with various number of pulses at different repetition rates and laser fluences. Effects of the irradiation on the optical and structural properties of the crystal are analyzed by UV–vis-NIR spectroscopy. Annihilation of some point defects of the crystal structure is observed following laser irradiation at a fluence of 100 mJ cm⁻² with 100 and 500 pulses. Increasing the laser fluence and pulse numbers leads to saturation and new defects are found to be formed in the crystal. Additional absorption spectra of the irradiated samples show that oxygen vacancies in the Nd:YAG crystals are removed during the low-dose irradiation. The laser irradiation is compared to the thermal annealing process for Nd:YAG crystal modification. Additional absorption spectrum of an annealed sample reveals that induced negative absorption band at 236 nm is correlated with the annihilation of the oxygen vacancy center. Our results also demonstrate that XeCl laser treatment has several advantages upon annealing at high temperatures in the Nd:YAG crystal quality improvement. Thus, the present work can give a new approach to modify Nd:YAG crystals to be used in a wide variety of solid-state laser engineering.     

LD泵浦Nd:YAG连续激光器转换性能实验研究

设计了LD端面泵浦固体Nd:YAG连续激光器平台,研究了LD泵浦功率、输出镜透过率和谐振腔腔长对激光器转换性能的影响. 该系统可实现连续1.064 μm近红外激光输出,转换效率可达42.2%.     

大功率Nd∶YAG固体激光器

介绍了一台单级输出灯泵浦大功率脉冲Nd∶YAG激光器。该激光器脉宽0.1-10ms可调,频率1-1000hz可调,总注入电功率12kw。试验得到激光器参数脉冲宽度和频率协调改变,可使激光器在整个脉宽范围内都能稳定500w输出;最大单脉冲能量56J;总体电光效率4.2%;光束质量为25mm.mrad;功率稳定性±2%。     

Investigation of Cr:YAG passive mode-locking in a pulsed Nd:YAG laser

Passive mode-locking of a pulsed Nd:YAG laser using a Cr⁴⁺:YAG saturable absorber was realized for the first time in a nearly critical stable resonator containing an antiresonant ring structure. The output energy and pulse duration are 13.5 mJ and 180 ps, respectively. The recovery time and saturable intensity for excited-state absorption of Cr⁴⁺:YAG under the action of strong laser pulses were calculated from rate equations.     

高平均功率调Q准连续Nd:YAG激光器

通过选用低掺杂浓度的Nd:YAG晶体棒、热近非稳腔优化设计、双棒串接热致双折射补偿技术以及双Q开关正交放置结构，在LD抽运功率1116W时，实现调Q准连续全固态Nd:YAG激光器1064nm输出，平均功率达258W，光束质量M²～15.5，重复频率为10kHz，脉冲宽度为64ns，峰值功率达0.4GW，光光转换效率达23.1%. 关键词： Nd:YAG激光器 准连续波 激光二极管抽运 固体激光器     

Pump pulse characteristics of quasi-continuous-wave diode-side-pumped Nd:YAG laser

The influence of pumping laser pulse on the property of quasi-continuous-wave (QCW) diode-side-pumped Nd:YAG laser is investigated theoretically and experimentally. Under remaining a fixed duty cycle, the average output power increases, and the corresponding thermal focal length shorten with the increase of the pump pulse duration, which attributes to the decrease of the ratio of pulse buildup time to the pulse duration. At a pump power of 146 W, the laser output power changes from 65.1 W to 81.2 W when the pulse duration is adjusted from 150 μ s to 1000 μ s, confirming a significant enhancement of 24.7%. A laser rate equation model incorporating the amplified spontaneous emission is also utilized and numerically solved, and the simulated results agree well with the experimental data.