Synthesis and optical characterization of nanocrystalline CdTe thin films

From several years the study of binary compounds has been intensified in order to find new materials for solar photocells. The development of thin film solar cells is an active area of research at this time. Much attention has been paid to the development of low cost, high efficiency thin film solar cells. CdTe is one of the suitable candidates for the production of thin film solar cells due to its ideal band gap, high absorption coefficient. The present work deals with thickness dependent study of CdTe thin films. Nanocrystalline CdTe bulk powder was synthesized by wet chemical route at pH≈11.2 using cadmium chloride and potassium telluride as starting materials. The product sample was characterized by transmission electron microscope, X-ray diffraction and scanning electron microscope. The structural characteristics studied by X-ray diffraction showed that the films are polycrystalline in nature. CdTe thin films with thickness 40, 60, 80 and 100 nm were prepared on glass substrates by using thermal evaporation onto glass substrate under a vacuum of 10⁻⁶ Torr. The optical constants (absorption coefficient, optical band gap, refractive index, extinction coefficient, real and imaginary part of dielectric constant) of CdTe thin films was studied as a function of photon energy in the wavelength region 400–2000 nm. Analysis of the optical absorption data shows that the rule of direct transitions predominates. It has been found that the absorption coefficient, refractive index (n) and extinction coefficient (k) decreases while the values of optical band gap increase with an increase in thickness from 40 to 100 nm, which can be explained qualitatively by a thickness dependence of the grain size through decrease in grain boundary barrier height with grain size.     

Structural and optical properties of YSZ thin films grown by PLD technique

We report on the structural and optical properties of yttria stabilized zirconia (YSZ) thin films grown by pulsed laser deposition (PLD) technique and in situ crystallized at different substrate temperatures (T_s = 400 °C, 500 °C and 600 °C). Yttria-stabilized zirconia target of ∼1 in. diameter (∼95% density) was fabricated by solid state reaction method for thin film deposition by PLD. The YSZ thin films were grown on an optically polished quartz substrates and the deposition time was 30 min for all the films. XRD analysis shows cubic crystalline phase of YSZ films with preferred orientation along 〈1 1 1〉. The surface roughness was determined by AFM for the films deposited at different substrate temperatures. The nano-sized surface roughness is found to increase with the increase of deposition temperatures. For the optical analysis, a UV-vis-NIR spectrophotometer was used and the optical band gap of ∼5.7 eV was calculated from transmittance curves.     

Chemical,optical, and electrical characterization of Ga2O3 thin films grown by plasma-enhanced atomic layer deposition

Thin Ga₂O₃ films were grown on Si (100) using trimethylgallium (TMG) and oxygen as the precursors through plasma-enhanced atomic layer deposition. The depositions were made over a temperature range of 80–250?°C with a growth per cycle of around 0.07 nm/cycle. Surface self-saturating growth was obtained with TMG pulse time ≥20?ms?at a temperature of 150?°C. The root mean square surface roughness of the obtained Ga₂O₃ films increased from 0.1?nm to 0.3?nm with increasing the growth temperature. Moreover, the x-ray photoelectron spectroscopy analysis indicated that the obtained film was Ga-rich with the chemical oxidation states Ga³⁺ and Ga¹⁺, and no carbon contamination was detected in the films after Ar⁺ sputtering. The electron density of films measured by x-ray reflectivity varied with the growth temperature, increasing from 4.72 to 5.80?g/cm³. The transmittance of Ga₂O₃ film deposited on a quartz substrate was obtained through ultraviolet visible (UV–Vis) spectroscopy. An obvious absorption in the deep UV region was demonstrated with a wide band gap of 4.6–4.8?eV. The spectroscopic ellipsometry analysis indicated that the average refractive index of the Ga₂O₃ film was 1.91?at 632.8?nm and increased with the growth temperature due to the dense structure of the films. Finally, the I-V and C-V characteristics proved that the Ga₂O₃ films prepared in this work had a low leakage current of 7.2?×?10^?11 A/cm² at 1.0?MV/cm and a high permittivity of 11.9, suitable to be gate dielectric.     

Study on field-emission characteristics of electrodeposited Co-doped ZnO thin films

Co-doped ZnO films were fabricated using electrodeposition method on the ITO substrates. The structure of the Co-doped ZnO films was analyzed by X-ray diffraction and scanning electron microscope. The field-emission characteristics of the prepared Co-doped ZnO films were examined using diode structure in a vacuum chamber. The examined results indicate that the Co-doping cause the turn-on field increasing by increasing the concentration of the Co-dopant, probably due to the band gap changing, which could attributed to the sp-d exchange interactions between the band electrons and the localized d electrons of the Co²⁺ ions substituting Zn ions in the films.     

Laser-induced changes in some of the optical properties of Ge20Bi10Se70 thin films

We have investigated photon-induced changes of optical parameters of amorphous Ge₂₀Bi₁₀Se₇₀ thin films due to illumination by laser irradiation. Absorption peaks were detected in the tailing area in the wavelength range between 300 and 600 nm. These peaks reduced to two peaks in the higher dose (9 J/cm²). The optical energy gap E _gd was found to have the well known direct-allowed transition mechanism. Values of E _gd show that all films exhibit a photo-induced photo-darkening effect indicated by a red shift of E _gd. The higher laser dose shows an increase in E _gd values. The effect of laser on other optical constants was also investigated. The refractive index (n), extinction coefficient (k) and dielectric constant of irradiated films were also calculated.     

Thickness effect on the structural and optical constants of stibnite thin films prepared by sulfidation annealing of antimony films

This paper deals with some physical properties of antimony sulphide Sb₂S₃ thin films obtained by an annealing process in sulphur vapors at 300 °C of Sb thermal evaporated thin films deposited on glass substrate. The crystal structure and surface morphology were investigated by both XRD and AFM techniques. This structural study shows that Sb₂S₃ thin films were well crystallized in orthorhombic structure and some parameters such as the lattice parameter, crystallite size, microstrain and degree of preferred orientation have been reported and correlated with the effect of crystallite size. On the other hand, the refractive index and the extinction coefficient were discussed in terms of the Forouhi–Bloomer model. The optical band gap was found to range from 1.75 to 2.23 eV. Finally, the analysis of the optical parameters extracted from the Urbach–Martienssen and Forouhi–Bloomer models lead to some explanations of the correlations between the structural properties in terms of the crystallite size and optical ones.     

Electrodeposition and growth mechanism of SnSe thin films

Tin selenide (SnSe) thin films were electrochemically deposited onto Au(1 1 1) substrates from an aqueous solution containing SnCl₂, Na₂SeO₃, and EDTA at room temperature (25 °C). The electrochemical behaviors and the codeposition potentials of Sn and Se were explored by cyclic voltammetry. X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and UV-vis absorption spectroscopy were employed to characterize the thin films. When the electrodeposition potential increased, the Se content in the films decreased. It was found that the stoichiometric SnSe thin films could be obtained at −0.50 V. The as-deposited films were crystallized in the preferential orientation along the (1 1 1) plane. The morphologies of SnSe films could be changed from spherical grains to platelet-like particles as the deposition potential increases. The SEM investigations show that the film growth proceeds via nucleation, growth of film layer and formation of needle-like particles on the overlayer of the film. The optical absorption study showed the film has direct transition with band gap energy of 1.3 eV.     

Thermal stress induced band gap variation of ZnO thin films

The growth temperature and post annealing-dependent optical and structural effect of RF magnetron sputtered ZnO thin films were examined. As the growth temperature increased, the lattice constant increased and approached the bulk value, suggesting a decrease in interfacial strain between the substrate and thin film. For the post annealed samples, the interfacial strain decreased further and was close to the bulk value regardless of the post annealing environments (in air and O₂). The optical properties of all ZnO thin films examined and revealed higher transparency (>90%). Furthermore, the optical band gap varied according to the growth temperature and post annealing environments due to a decrease in the interfacial strain effect.     

Influence of glucose on the structural and optical properties of ZnO thin films prepared by sol-gel method

In this work, ZnO thin films were prepared by sol-gel method on glass substrates followed by calcinations at 500 °C for an hour. The effect of glucose on the structure and optical properties of the films was studied. The structural characteristics of the samples were analyzed by X-ray diffractometer (XRD) and atomic force microscope (AFM). The optical properties were studied by a UV-visible spectrophotometer. The results show that some of the prepared ZnO thin films have a high preferential oriented c-axis orientation with compact hexagonal wurtzite structure due to a proper amount of glucose introducing. After introducing the glucose additive in ZnO colloids, the intensity of (002) peak, the transmittance, and the optical band gap of the ZnO thin films increases because of the enhanced ZnO crystallization. On the contrary, the absorbance, the film thickness, and the surface root-mean-square (RMS) roughness of the ZnO thin films decreases. The glucose additive could not only improve the surface RMS roughness and microstructure of ZnO thin films, but also enhance the transmittance and the energy band gap more easily.     

立方氮化硼薄膜的光学带隙

用射频溅射法在p型Si(100)衬底上沉积立方氮化硼(c-BN)薄膜,薄膜的成分由傅里叶变换红外谱标识,用紫外-可见分光光度计测量了c-BN薄膜的反射光谱,利用K-K(Kramers-Kroning)关系从反射谱计算出c-BN薄膜的光吸收系数,进而确定c-BN薄膜的光学带隙.对于立方相含量为55.4%的c-BN薄膜,光学带隙为5.38eV. 关键词： 立方氮化硼薄膜 光学带隙 K-K关系     

Preparation and optical properties of barium titanate thin films

Barium titanate (BTO) films were prepared by sol-gel spin-coating technique. The crystal structure and optical properties of BTO films have been investigated. The results indicate that the BTO films are single perovskite phase having tetragonal symmetry. The band gap of the BTO films increases with the increasing of layer number and decreasing of solution concentration. The transmittance and band gap of the BTO films annealed at 900 °C is more than that of the BTO films annealed at 700 °C when wavelength is 200-1000 nm. When wavelength is 400-1000 nm, the absorption coefficient α obtained by experiment is higher than that obtained by calculation (close to zero).     

Effect of annealing on the surface and band gap alignment of CdZnS thin films

Effects of the annealing temperature on structural, optical and surface properties of chemically deposited cadmium zinc sulfide (CdZnS) films were investigated. X-ray diffraction (XRD) results showed that the grown CdZnS thin films formed were polycrystalline with hexagonal structure. Atomic force microscopy (AFM) studies showed that the surface roughness of the CdZnS thin films was about 60-400 nm. Grain sizes of the CdZnS thin films varied between 70 and 300 nm as a function of annealing temperature. The root mean square surface roughness of the selected area, particular point, average roughness profile, topographical area of roughness were measured using the reported AFM software. The band gaps of CdZnS thin films were determined from absorbance measurements in the visible range as 300 nm and 1100 nm, respectively, using Tauc theory.     

Hydrothermal synthesis and characterization of ZnO films with different nanostructures

ZnO films with morphologies of nanorods, nanowires and nanosheets were grown on F-doped SnO₂ glass substrate, which may have potential application in solar cells. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were employed to characterize the structures and morphologies of the as-synthesized samples. The photoluminescence (PL) and the photoelectrochemical properties of ZnO films were also measured. The results showed that ZnO nanorods preferentially oriented along the c-axis and had the largest photocurrent density which is as high as 60 μA/cm².     

Structural characterization and magnetoresistance of manganates thin films and Fe-doped manganates thin films

Perovskites thin films with the composition La_0.6Ca_0.4MnO₃ doped with 20% Fe, were prepared by pulsed reactive crossed beam laser ablation, where a synchronized reaction gas pulse interacts with the ablation plume. The films were grown on various substrates and the highest colossal magnetoresistance ratio (CMR) was detected by Hall measurements for films grown on LaAlO₃ (1 0 0), which was selected as substrate for further investigations.Several growth parameters, such as substrate temperature and target to substrate distance were varied to analyze their influence on the film properties.The structure of the deposited thin films was characterized by X-ray diffraction and atomic force microscope, while Rutherford backscattering (RBS) was used to determine the film stoichiometry. The electrical properties were determined by Hall effect measurements in a magnetic field of 0.51 T.These measurements reveal that the amplitude of the CMR ratio depends strongly on the substrate and that the oxygen content influences the temperature where the transition from semiconductor to metal is observed.     

Investigation of induced parallel magnetic anisotropy at low deposition temperature in Ba-hexaferrites thin films

In this paper we present the effect of low substrate temperature on structural, morphological, magnetic and optical properties of Ba-hexaferrite thin films. Films were deposited on single crystal Silicon (1 0 0) substrate employing the Pulsed Laser Deposition (PLD) technique. The structural, morphological, magnetic and optical properties are found to be strongly dependent on substrate temperature. The low substrate temperatures (room temperature to 200 °C) restrict the formation of larger grains. For the higher substrate temperature i.e., 400 °C, the grain size of the deposited thin film are much larger. The film grown at low substrate temperature do not show any anisotropy. As the substrate temperature is increased, the easy axis of the films alinged itself in the direction parallel to the film plane whereas the hard axis remained in the perpendicular direction. The higher substrate temperature caused the uniaxial magnetic anisotropy, which is very important in magnetic recording devices. The saturation magnetization and optical band gap energy values of 62 emu/cc and 1.75 eV, respectively, were achieved for the film of thickness 500 nm deposited at 400 °C. Higher values of coercivity, squareness and films thickness are associated with the growth of larger grains at higher substrate temperature.     

微量掺碳nc-SiC:H薄膜用于p-i-n太阳电池的窗口层

采用等离子增强化学气相沉积方法(PECVD)制备了微量掺碳的p型纳米非晶硅碳薄膜(p-nc-SiC：H)，反应气体为硅烷和甲烷，掺杂气体采用硼烷，沉积温度分别采用333K，353K和373K.测量结果表明随着沉积温度增加和碳含量的增加，薄膜的光学带隙增加；薄膜具有较宽的带隙和较高的电导率，同时有较低的激活能(0.06eV).Raman和XRD测量结果表明薄膜存在纳米晶.优化的p型纳米非晶硅碳薄膜作为非晶硅p-i-n太阳电池的窗口层，使得太阳电池的开路电压达到0.94V. 关键词： 光学带隙 纳米硅 薄膜 太阳能电池     

Effects of metal doping on the physical properties of ZnTe thin films

Zinc telluride (ZnTe) thin films were sublimated on a glass substrate using closed space sublimation (CSS) technique. ZnTe thin films of same thickness were tailored with copper (Cu) & silver (Ag) doping, considered for comparative study. X-ray diffraction (XRD) patterns of as-deposited ZnTe thin film and doped ZnTe samples exhibited polycrystalline behavior. The preferred orientation of (111) having cubic phase was observed. XRD patterns indicated that the crystallite size had increased after silver and copper immersion in as-deposited ZnTe thin films. Scanning electron microscopy (SEM) was used to observe the change of as-deposited and doped sample's grains sizes. EDX confirmed the presence of Cu and Ag in the ZnTe thin films after doping respectively. The optical studies showed the decreasing trend in energy band gap after Cu and Ag-doping. Transmission also decreased after doping. Resistivity of as-deposited ZnTe thin film was about 10⁶ Ω cm. The resistivity was reduced to 68.97 Ω cm after Cu immersion, and 10⁴ Ω cm after Ag immersion. Raman spectra were used to check the crystallinity of as-deposited, Cu and Ag-doped ZnTe thin film samples.     

Electrical and optical properties of ZnO thin films prepared by magnetron rf sputtering—influence of Al, Er and H

The influence of Al, Er and H in ZnO thin films (ZnO:Al, ZnO:Er and ZnO:H) deposited by magnetron sputtering at different substrate temperatures, T_s, on their optical, structural and electrical properties was investigated. X-ray diffraction (XRD) analyses show an improvement of the crystalline structure with increasing T_s. The optical band gap, , of the films, from transmission and reflection spectra, ranged from 3.27 to 3.41 eV. The Urbach band tail width was also calculated. Incorporation of Al and Er resulted in a reduced and an increased resistivity, ρ, respectively, and an increase in the Urbach tail width in both cases. However, sputtering in an Ar+H₂ gas mixture led to an increase in ρ and an improvement in the structural order of the films. A discussion of the influence of T_s and of Al, Er and H on the properties is presented.     

Influence of thermal annealing on optical and structural properties change in Bi-doped Ge30Se70 thin films

The effect of annealing on the structural and optical properties of thermally evaporated Ge₃₀Se₇₀ and Ge₃₀Se₆₀Bi₁₀ thin films is reported in this paper. The prepared films were thermally annealed at 250°C to optimize the optical properties which can be used for the optical device fabrication. X-ray diffraction study revealed no structural transformation whereas the surface morphology changed as observed from scanning electron microscopy. The optical properties of the deposited and annealed films have been investigated by using a UV–VIS–NIR spectrophotometer in the wavelength range of 400–1100?nm. The optical band gap of the Ge₃₀Se₇₀ annealed film is found to be increased while the energy gap of the Bi-doped annealed Ge₃₀Se₆₀Bi₁₀ thin film decreased which is explained by the chemical disorderness, defect states and density of localized states in the mobility gap. The Tauc parameter and Urbach energy which measure the degree of disorder changed with the annealing process. The transmittivity increases and the absorption power decreases in the Ge₃₀Se₇₀ annealed film, whereas the reverse effect is noticed for the annealed Ge₃₀Se₆₀Bi₁₀ thin film. The irreversible nature of this change can be useful for optical recording purposes.     

A study of energy band gap versus temperature for Cu2ZnSnS4 thin films

The temperature dependent band gap energy of Cu₂ZnSnS₄ thin film was studied in the temperature range of 77-410 K. Various relevant parameters, which explain the temperature variation of the fundamental band gap, have been calculated using empirical and semi-empirical models. Amongst the models evaluated, the Varshni and Pässler models show the best agreement with experimental data in the middle temperature range. However, the Bose-Einstein model fits reasonably well over the entire temperature range evaluated. The calculated fitting parameters are in good agreement with the estimated value of the Debye temperature calculated using the Madelung-Einstein approximation and the Hailing method.