Interface characterization and current conduction in HfO2-gated MOS capacitors

Metal-oxide-semiconductor (MOS) capacitors incorporating hafnium dioxide (HfO₂) dielectrics were fabricated and investigated. In this work, the electrical and interfacial properties were characterized based on capacitance-voltage (C-V) and current-voltage (I-V) measurements. Thereafter the current conduction mechanism, electron effective mass (m*), mean density of interface traps per unit area and energy (), energy distribution of interface traps density and near-interface oxide traps density (N_NIOT) were studied in details. The characterization reveals that the dominant conduction mechanism in the region of high temperature and high field is Schottky emission. The mean density of interface traps per unit area and energy is about 6.3 × 10¹² cm⁻² eV⁻¹ by using high-low frequency capacitance method. The maximum D_it is about 7.76 × 10¹² cm⁻² eV⁻¹ located at 0.27 eV above the valence band.     

Electrical characterisation of ruthenium Schottky contacts on n-Ge (1 0 0)

Ruthenium (Ru) Schottky contacts were fabricated on n-Ge (1 0 0) by electron beam deposition. Current–voltage (I–V), deep level transient spectroscopy (DLTS), and Laplace-DLTS techniques were used to characterise the as-deposited and annealed Ru/n-Ge (1 0 0) Schottky contacts. The variation of the electrical properties of the Ru samples annealed between 25 °C and 575 °C indicates the formation of two phases of ruthenium germanide. After Ru Schottky contacts fabrication, an electron trap at 0.38 eV below the conduction band with capture cross section of 1.0×10⁻¹⁴ cm⁻² is the only detectable electron trap. The hole traps at 0.09, 0.15, 0.27 and 0.30 eV above the valence band with capture cross sections of 7.8×10⁻¹³ cm⁻², 7.1×10⁻¹³ cm⁻², 2.4×10⁻¹³ cm⁻² and 6.2×10⁻¹³ cm⁻², respectively, were observed in the as-deposited Ru Schottky contacts. The hole trap H(0.30) is the prominent single acceptor level of the E-centre, and H(0.09) is the third charge state of the E-centre. H(0.27) shows some reverse annealing and reaches a maximum concentration at 225 °C and anneals out after 350 °C. This trap is strongly believed to be V–Sb₂ complex formed from the annealing of V–Sb defect centre.     

Improved electrical and interfacial properties of RF-sputtered HfAlOx on n-GaAs with effective Si passivation

In this paper, we present the effects of ultrathin Si interfacial layer on the physical and electrical properties of GaAs MOS capacitors fabricated using RF-sputtered HfAlO_x gate dielectric. It is found that HfAlO_x/Si/n-GaAs stack exhibits excellent electrical properties with low frequency dispersion (∼4.8%), hysteresis voltage (0.27 V) and interface trap density (1.3 × 10¹² eV⁻¹ cm⁻²). The current density of 3.7 × 10⁻⁵ A/cm² is achieved with an equivalent-oxide-thickness of 1.8 nm at V_FB + 1 V for Si-passivated HfAlO_x films on n-GaAs. X-ray photoelectron spectroscopy (XPS) analysis shows that the suppression of low-k interfacial layer formation is accomplished with the introduction of ultrathin Si interface control layer (ICL). Thus the introduction of thin layer of Si between HfAlO_x dielectrics and GaAs substrate is an effective way to improve the interface quality such as low frequency dispersion, hysteresis voltage and leakage current. Additionally, current conduction mechanism has been studied and the dominant conduction mechanisms are found to be Schottky emission at low to medium electric fields and Poole-Frenkel at high fields and high temperatures under substrate injection. In case of gate injection, the main current conduction at low field is found to be the Schottky emission at high temperatures.     

Characteristics of sandwich-structured Al2O3/HfO2/Al2O3 gate dielectric films on ultra-thin silicon-on-insulator substrates

Sandwich-structure Al₂O₃/HfO₂/Al₂O₃ gate dielectric films were grown on ultra-thin silicon-on-insulator (SOI) substrates by vacuum electron beam evaporation (EB-PVD) method. AFM and TEM observations showed that the films remained amorphous even after post-annealing treatment at 950 °C with smooth surface and clean silicon interface. EDX- and XPS-analysis results revealed no silicate or silicide at the silicon interface. The equivalent oxide thickness was 3 nm and the dielectric constant was around 7.2, as determined by electrical measurements. A fixed charge density of 3 × 10¹⁰ cm⁻² and a leakage current of 5 × 10⁻⁷A/cm² at 2 V gate bias were achieved for Au/gate stack /Si/SiO₂/Si/Au MIS capacitors. Post-annealing treatment was found to effectively reduce trap density, but increase in annealing temperature did not made any significant difference in the electrical performance.     

A study of interface characteristics in HfAlO/p-Si by deep level transient spectroscopy

Deep level transient spectroscopy (DLTS) and high-frequency capacitance-voltage (HF-CV) measurement are used for the investigation of HfAlO/p-Si interface. The so-called “slow” interface states detected by HF-CV are obtained to be 2.68 × 10¹¹ cm⁻². Combined conventional DLTS with insufficient-filling DLTS (IF-DLTS), the true energy level position of interfacial traps is found to be 0.33 eV above the valance band maximum of silicon, and the density of such “fast” interfacial traps is 1.91 × 10¹² cm⁻² eV⁻¹. The variation of energy level position of such traps with different annealing temperatures indicates the origin of these traps may be the oxide-related traps very close to the HfAlO/Si interface. The interfacial traps’ passivation and depassivation effect of postannealing in forming gas are shown by comparing samples annealed at different temperatures.     

Current-voltage characteristics of Au/GaN/GaAs structure

Au/GaN/n-GaAs structure has been fabricated by the electrochemically anodic nitridation method for providing an evidence of achievement of stable electronic passivation of n-doped GaAs surface. The change of the electronic properties of the GaAs surface induced by the nitridation process has been studied by means of current-voltage (I-V) characterizations on Schottky barrier diodes (SBDs) shaped on gallium nitride/gallium arsenide structure. Au/GaN/n-GaAs Schottky diode that showed rectifying behavior with an ideality factor value of 2.06 and barrier height value of 0.73 eV obeys a metal-interfacial layer-semiconductor (MIS) configuration rather than an ideal Schottky diode due to the existence of GaN at the Au/GaAs interfacial layer. The formation of the GaN interfacial layer for the stable passivation of gallium arsenide surface is investigated through calculation of the interface state density N_ss with and without taking into account the series resistance R_s. While the interface state density calculated without taking into account R_s has increased exponentially with bias from 2.2×10¹² cm⁻² eV⁻¹ in (E_c−0.48) eV to 3.85×10¹² cm⁻² eV⁻¹ in (E_c−0.32) eV of n-GaAs, the N_ss obtained taking into account the series resistance has remained constant with a value of 2.2×10¹² cm⁻² eV⁻¹ in the same interval. This has been attributed to the passivation of the n-doped GaAs surface with the formation of the GaN interfacial layer.     

High-conductive nanocrystalline silicon with phosphorous and boron doping

Intrinsic, P- and B-doped hydrogenated amorphous silicon thin films were prepared by plasma-enhanced chemical vapor deposition technique. As-deposited samples were thermally annealed at the temperature of 800 °C to obtain the doped nanocrystalline silicon (nc-Si) films. The microstructures, optical and electronic properties have been evaluated for the undoped and doped nanocrystalline films. X-ray photoelectron spectroscopy (XPS) measurements demonstrated the presence of the substitutional boron and phosphorous in the doped films. It was found that thermal annealing can efficiently activate the dopants in films accompanying with formation of nc-Si grains. Based on the temperature-dependent conductivity measurements, it was shown that the activation of dopant by annealing increased the room temperature dark conductivity from 3.4 × 10⁻⁴ S cm⁻¹ to 5.3 S cm⁻¹ for the P-doped films and from 1.28 × 10⁻³ S cm⁻¹ to 130 S cm⁻¹ for the B-doped films. Meanwhile, the corresponding value of conductivity activation energies was decreased from 0.29 eV to 0.03 eV for the P-doped films and from 0.3 eV to 5.6 × 10⁻⁵ eV for the B-doped films, which indicated the doped nc-Si films with high conductivity can be achieved with the present approach.     

The dependence of barrier height on temperature for Pd Schottky contacts on ZnO

Temperature dependent current-voltage (I-V) and capacitance-voltage (C-V) measurements have been performed on Pd/ZnO Schottky barrier diodes in the range 60-300 K. The room temperature values for the zero bias barrier height from the I-V measurements (Φ_I-V) was found to be 0.52 eV and from the C-V measurements (Φ_C-V) as 3.83 eV. From the temperature dependence of forward bias I-V, the barrier height was observed to increase with temperature, a trend that disagrees with the negative temperature coefficient for semiconductor material. The C-V barrier height decreases with temperature, a trend that is in agreement with the negative temperature coefficient of semiconductor material. This has enabled us to fit two curves in two regions (60-120 K and 140-300 K). We have attributed this behaviour to a defect observed by DLTS with energy level 0.31 eV below the conduction band and defect concentration of between 4×10¹⁶ and 6×10¹⁶ cm⁻³ that traps carriers, influencing the determination of the barrier height.     

Characterization of Y2O3 gate dielectric on n-GaAs substrates

Physical and electrical properties of sputtered deposited Y₂O₃ films on NH₄OH treated n-GaAs substrate are investigated. The as-deposited films and interfacial layer formation have been analyzed by using X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS). It is found that directly deposited Y₂O₃ on n-GaAs exhibits excellent electrical properties with low frequency dispersion (<5%), hysteresis voltage (0.24 V), and interface trap density (3 × 10¹² eV⁻¹ cm⁻²). The results show that the deposition of Y₂O₃ on n-GaAs can be an effective way to improve the interface quality by the suppression on native oxides formation, especially arsenic oxide which causes Fermi level pinning at high-k/GaAs interface. The Al/Y₂O₃/n-GaAs stack with an equivalent oxide thickness (EOT) of 2.1 nm shows a leakage current density of 3.6 × 10⁻⁶ A cm⁻² at a V_FB of 1 V. While the low-field leakage current conduction mechanism has been found to be dominated by the Schottky emission, Poole-Frenkel emission takes over at high electric fields. The energy band alignment of Y₂O₃ films on n-GaAs substrate is extracted from detailed XPS measurements. The valence and conduction band offsets at Y₂O₃/n-GaAs interfaces are found to be 2.14 and 2.21 eV, respectively.     

Effects of swift heavy ion irradiation on the electrical characteristics of Au/n-GaAs Schottky diodes

Metal-semiconductor diode of Au/n-GaAs is studied under the irradiation of swift heavy ion (SHI) beam (80 MeV ¹⁶O⁶⁺), using in situ current-voltage characterization technique. The diode parameters like ideality factor, barrier height, and leakage current are observed to vary with irradiation fluence. Significantly, the diode performance improves at a high fluence of 2 × 10¹³ ions cm⁻² with a large decrease of reverse leakage current in comparison to the original as deposited sample. The Schottky barrier height (SBH) also increases with fluence. At a high irradiation fluence of 5 × 10¹³ ions cm⁻² the SBH (0.62 ± 0.01 eV) is much larger than that of the as deposited sample (0.55 ± 0.01 eV). The diode parameters remain stable over a large range of irradiation up to fluence of 8 × 10¹³ ions cm⁻². A prominent annealing effect of the swift ion beam owing to moderate electronic excitation and high ratio of electronic energy loss to the nuclear loss is found to be responsible for the improvement in diode characteristics.     

The characteristics of platinum diffusion in n-type GaN

The electrical and optical characteristics of platinum (Pt) diffusion in n-type gallium nitride (GaN) film are investigated. The diffusion extent was characterized by the SIMS technique. The temperature-dependent diffusion coefficients of Pt in n-GaN are 4.158 × 10⁻¹⁴, 1.572 × 10⁻¹³ and 3.216 × 10⁻¹³ cm²/s at a temperature of 650, 750 and 850 °C, respectively. The Pt diffusion constant and activation energy in GaN are 6.627 × 10⁻⁹ cm²/s and 0.914 eV, respectively. These results indicate that the major diffusion mechanism of Pt in GaN is possibly an interstitial diffusion. In addition, it is also observed that the Pt atom may be a donor because the carrier concentration in Pt-diffused GaN is higher than that in un-diffused GaN. The optical property is studied by temperature-dependent photoluminescence (PL) measurement. The thermal quenching of the PL spectra for Pt-diffused GaN samples is also examined.     

The barrier height inhomogeneity in Al/p-Si Schottky barrier diodes with native insulator layer

The current-voltage (I-V) characteristics of Al/p-Si Schottky barrier diodes (SBDs) with native insulator layer were measured in the temperature range of 150-375 K. The estimated zero-bias barrier height Φ_B0 and the ideality factor n assuming thermionic emission (TE) theory show strong temperature dependence. Evaluation of the forward I-V data reveals an increase of zero-bias barrier height Φ_B0 but decrease of ideality factor n with increase in temperature. The conventional Richardson plot exhibits non-linearity below 250 K with the linear portion corresponding to activation energy of 0.41 eV and Richardson constant (A^*) value of 1.3 × 10⁻⁴ A cm⁻² K⁻² is determined from intercept at the ordinate of this experimental plot, which is much lower than the known value of 32 A cm² K² for holes in p-type Si. Such behavior is attributed to Schottky barrier inhomogene ties by assuming a Gaussian distribution of barrier heights (BHs) due to barrier height inhomogeneities that prevail at interface. Also, Φ_B0 versus q/2kT plot was drawn to obtain evidence of a Gaussian distribution of the BHs, and values of Φ_B0 = 1.055 eV and σ₀ = 0.13 V for the mean BH and zero-bias standard deviation have been obtained from this plot, respectively. Thus, the modified versus q/kT plot gives Φ_B0 and A^* as 1.050 eV and 40.08 A cm⁻² K⁻², respectively, without using the temperature coefficient of the barrier height. This value of the Richardson constant 40.03 A cm⁻² K⁻² is very close to the theoretical value of 32 A K⁻² cm⁻² for p-type Si. Hence, it has been concluded that the temperature dependence of the forward I-V characteristics of the Al/p-Si Schottky barrier diodes with native insulator layer can be successfully explained on the basis of TE mechanism with a Gaussian distribution of the barrier heights.     

Pb(Zr0.53Ti0.47)O3 thin films with different thicknesses obtained at low temperature by microwave irradiation

Pb(Zr_0.53Ti_0.47)O₃ (PZT) thin films with different thicknesses (99-420 nm) were prepared on Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by sol-gel method and films were annealed at 450 °C for 30 min using a single-mode cavity of 2.45 GHz microwaves. X-ray diffraction analysis indicated that the pyrochlore phase was transformed to the perovskite phase at above 166 nm films. The grain sizes were increased, surface roughnesses were decreased, and electrical properties were improved with film thickness. The leakage current density was 9 × 10⁻⁸ A/cm² at an applied electrical field of 100 kV/cm. The ohmic and field-enhanced Schottky emission mechanisms were used to explain leakage current behavior of the PZT thin films. These results suggest that microwave annealing is effective for obtaining low temperature crystallization of thin films with better properties.     

Temperature-dependent optical absorption measurements and Schottky contact behavior in layered semiconductor n-type InSe(:Sn)

The layered n-InSe(:Sn) single crystal samples have been cleaved from a large crystal ingot grown from non-stoichiometric melt by the Bridgman-Stockbarger method. It has been made the absorption measurements of these samples without Schottky contact under electric fields of 0.0 and 6000 V cm⁻¹. The band gap energy value of the InSe:Sn has been calculated as 1.36 ± 0.01 eV (at 10 K) and 1.28 ± 0.01 eV (at 300 K) under zero electrical field, and 1.31 ± 0.01 eV (at 10 K) and 1.26 ± 0.01 eV (at 300 K) under 6000 Vcm⁻¹. The current-voltage (I-V) characteristics of Au-Ge/InSe(:Sn)/In Schottky diodes have been measured in the temperature range 80-320 K with a temperature step of 20 K. An experimental barrier height (BH) Φ_ap value of about 0.70 ± 0.01 eV was obtained for the Au-Ge/InSe(:Sn)/In Schottky diode at the room temperature (300 K). An abnormal decrease in the experimental BH Φ_b and an increase in the ideality factor n with a decrease in temperature have been explained by the barrier inhomogeneities at the metal-semiconductor interface. From the temperature-dependent I-V characteristics of the Au-Ge/InSe(:Sn)/In contact, that is, and A^* as 0.94 ± 0.02 and 0.58 ± 0.02 eV, and 27 ± 2 and 21 ± 1 (A/cm² K²), respectively, have been calculated from a modified versus 1/T plot for the two temperature regions. The Richardson constant values are about two times larger than the known value of 14.4 (A/cm² K²) known for n-type InSe. Moreover, in the temperature range 80-320 K, we have also discussed whether or not the current through the junction has been connected with TFE.     

Current–voltage temperature characteristics of Au/n-Ge (1 0 0) Schottky diodes

The variation in electrical characteristics of Au/n-Ge (1 0 0) Schottky contacts have been systematically investigated as a function of temperature using current–voltage (I−V) measurements in the temperature range 140–300 K. The I–V characteristics of the diodes indicate very strong temperature dependence. While the ideality factor n decreases, the zero-bias Schottky barrier height (SBH) (Φ_B) increases with the increasing temperature. The I–V characteristics are analyzed using the thermionic emission (TE) model and the assumption of a Gaussian distribution of the barrier heights due to barrier inhomogeneities at the metal–semiconductor interface. The zero-bias barrier height Φ_B vs. 1/2 kT plot has been used to show the evidence of a Gaussian distribution of barrier heights and values of Φ_B=0.615 eV and standard deviation σ_s0=0.0858 eV for the mean barrier height and zero-bias standard deviation have been obtained from this plot, respectively. The Richardson constant and the mean barrier height from the modified Richardson plot were obtained as 1.37 A cm⁻² K⁻² and 0.639 eV, respectively. This Richardson constant is much smaller than the reported of 50 A cm⁻² K⁻². This may be due to greater inhomogeneities at the interface.     

Transparent conducting molybdenum-doped zinc oxide films deposited by RF magnetron sputtering

A new transparent conducting oxide (TCO) film with low resistivity and high transmittance in the visible range, molybdenum-doped zinc oxide (MZO), was successfully prepared by RF magnetron sputtering method on glass substrates at room temperature. The structural, electrical, and optical properties as a function of film thickness were investigated. All the samples have a preferred orientation with the (0 0 2) planes parallel to the substrates. The resistivity initially decreases and then shows an increase with the increase of the film thickness. When the thickness is 400 nm, the film has its best crystallinity and lowest resistivity 9.2 × 10⁻⁴ Ω cm with a Hall mobility of 30 cm² V⁻¹ s⁻¹ and a carrier concentration of 2.3 × 10²⁰ cm⁻³. The average transmittance in the visible range exceeds 84% for all thickness films.     

An ab initio-based approach to phase diagram calculations for GaN(0 0 0 1) surfaces

Surface phase diagrams of GaN(0 0 0 1)-(2 × 2) and pseudo-(1 × 1) surfaces are systematically investigated by using our ab initio-based approach. The phase diagrams are obtained as functions of temperature T and Ga beam equivalent pressure p_Ga by comparing chemical potentials of Ga atom in the vapor phase with that on the surface. The calculated results imply that the (2 × 2) surface is stable in the temperature range of 700-1000 K at 10⁻⁸ Torr and 900-1400 K at 10⁻² Torr. This is consistent with experimental stable temperature range for the (2 × 2). On the other hand, the pseudo-(1 × 1) phase is stable in the temperature range less than 700 K at 10⁻⁸ Torr and less than 1000 K at 10⁻² Torr. Furthermore, the stable region of the pseudo-(1 × 1) phase almost coincides with that of the (2 × 2) with excess Ga adatom. This suggests that Ga adsorption or desorption during GaN MBE growth can easily change the pseudo-(1 × 1) to the (2 × 2) with Ga adatom and vice versa.     

Thermally stimulated current study of electron-irradiation induced defects in semi-insulating InP obtained by multiple-step wafer annealing

Electron-irradiation induced defects in semi-insulating (SI) InP wafers with Fe concentration ranging from 1.5×10¹⁵ to 2.5×10¹⁵ cm⁻³, which have been obtained by multiple-step wafer annealing (MWA) under phosphorus vapor pressure, were studied using a thermally stimulated current (TSC) method. New traps, e₁, e₂, e₃, e₄ and e₅, with activation energies of 0.22, 0.28, 0.37, 0.44 and 0.46 eV, respectively, were observed. Based upon the annealing behavior of traps and the calculated defect levels, traps e₁ and e₅ produced by the irradiation with electron doses above 1×10¹⁵ cm⁻² were linked to In_P and P_In antisite defects, respectively, that probably form complexes. Traps e₃ and e₄ produced by the irradiation with doses above 1×10¹⁴ cm⁻² were associated with In and P vacancy related defects, respectively.     

Hydrogen peroxide treatment on ZnO substrates to investigate the characteristics of Pt and Pt oxide Schottky contacts

We utilize hydrogen peroxide (H₂O₂) treatment on (0 0 0 1) ZnO substrates to investigate the characteristics of Pt and Pt oxide Schottky contacts (SCs). X-ray rocking curves show the mosaicity structure becomes larger after H₂O₂ treatment. Photoluminescence (PL) spectra show the yellow-orange emission peaking at ∼576-580 nm with respect to deep level of oxygen interstitials introduced by H₂O₂ treatment. The threshold formation of ZnO₂ resistive layer on H₂O₂-treated ZnO for 45 min is observed from grazing-incidence X-ray diffraction. The better electrical characteristic is performed by Pt oxide SC with the larger barrier height (1.09 eV) and the lower leakage current (9.52 × 10⁻¹¹ A/cm² at −2 V) than Pt SC on the H₂O₂-treated ZnO for 60 min. X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectrometer (SIMS) examinations indicate the promoted interface oxide bonding and Zn outdiffusion for Pt oxide contact, different from Pt contact. Based on current-voltage, capacitance-voltage, X-ray diffraction, PL spectra, XPS, and SIMS results, the possible mechanism for effective rectifying characteristic and enhanced Schottky behavior is given.     

Low temperature fabrication of 5-10 nm SiO2/Si structure using advanced nitric acid oxidation of silicon (NAOS) method

We have developed the advanced nitric acid oxidation of Si (NAOS) method to form relatively thick (5-10 nm) SiO₂/Si structure with good electrical characteristics. This method simply involves immersion of Si in 68 wt% nitric acid aqueous solutions at 120 °C with polysilazane films. Fourier transform infrared absorption (FT-IR) measurements show that the atomic density of the NAOS SiO₂ layer is considerably high even without post-oxidation anneal (POA), i.e., 2.28 × 10²² atoms/cm², and it increases by POA at 400 °C in wet-oxygen (2.32 × 10²² atoms/cm²) or dry-oxygen (2.30 × 10²² atoms/cm²). The leakage current density is considerably low (e.g., 10⁻⁵ A/cm² at 8 MV/cm) and it is greatly decreased (10⁻⁸ A/cm² at 8 MV/cm) by POA at 400 °C in wet-oxygen. POA in wet-oxygen increases the atomic density of the SiO₂ layer, and decreases the density of oxide fixed positive charges.