Effect of thickness on structural, optical and electrical properties of nanostructured ZnO thin films by spray pyrolysis

Transparent conducting zinc oxide thin films were prepared by spray pyrolytic decomposition of zinc acetate onto glass substrates with different thickness. The crystallographic structure of the films was studied by X-ray diffraction (XRD). XRD measurement showed that the films were crystallized in the wurtzite phase type. The grain size, lattice constants and strain in films were calculated. The grain size increases with thickness. The studies on the optical properties show that the direct band gap value increases from 3.15 to 3.24 eV when the thickness varies from 600 to 2350 nm. The temperature dependence of the electrical conductivity during the heat treatment was studied. It was observed that heat treatment improve the electrical conductivity of the ZnO thin films. The conductivity was found to increase with film thickness.     

The influence of substrate and annealing temperatures on electrical properties of p-type ZnO films

In this study, p-type ZnO films with excellent electrical properties were prepared by ultrasonic spray pyrolysis (USP) combining with a N-Al codoping technique. The influence of the substrate temperature and annealing temperature on electrical properties of ZnO films was investigated. The growth and doping process of ZnO films was explored by thermogravimetry, differential scanning calorimetry and mass spectrum (TG-DSC-MS) measurements. It is suggested that the variation of electrical properties of ZnO films with the substrate temperature and annealing temperature results from the removal of H element out of the films.     

Structural and electrical properties of nitrogen and aluminum codoped p-type ZnO films

To resolve the problem of p-type doping in ZnO, nitrogen and aluminum (N-Al) codoped ZnO films were prepared by the ultrasonic spray pyrolysis (USP) technique. The structural and electrical properties of N-Al codoped ZnO films were investigated. The results demonstrate that the undoped ZnO films exhibit the preferential orientation of (002) plane, while ZnO films show high orientation of (101) plane after codoping with N and Al. The N-Al codoped ZnO films under optimum conditions show p-type conduction, with a low resistivity of 1.7×10⁻²Ω cm, carrier concentration of 5.09×10¹⁸ cm⁻³ and high Hall mobility of 73.6 cm² V⁻¹ s⁻¹. A conversion from p-type conduction to n-type was observed during the increase of measurement temperature.     

As-doped p-type ZnO films grown on SiO2/Si by radio frequency magnetron sputtering

p-Type ZnO:As films with a hole concentration of 10¹⁶-10¹⁷ cm⁻³ and a mobility of 1.32-6.08 cm²/V s have been deposited on SiO₂/Si substrates by magnetron sputtering. XRD, SEM, Hall measurements are used to investigate the structural and electrical properties of the films. A p-n homojunction comprising an undoped ZnO layer and a ZnO:As layer exhibits a typical rectifying behavior. Our study demonstrates a simple method to fabricate reproducible p-type ZnO film on the SiO₂/Si substrate for the development of ZnO-based optoelectronic devices on Si-based substrates.     

Unidirectional variation of lattice constants of Al-N-codoped ZnO films by RF magnetron sputtering

Al-N-codoped ZnO films were fabricated by RF magnetron sputtering in the ambient of N₂ and O₂ on silicon (1 0 0) and homo-buffer layer, subsequently, annealed in O₂ at low pressure. X-ray diffraction (XRD) spectra show that as-grown and 600 °C annealed films grown by codoping method are prolonged along crystal c-axis. However, they are not prolonged in (0 0 1) plane vertical to c-axis. The films annealed at 800 °C are not prolonged in any directions. Codoping makes ZnO films unidirectional variation. X-ray photoelectron spectroscopy (XPS) shows that Al content hardly varies and N escapes with increasing annealing temperature from 600 °C to 800 °C.     

Rapid thermal annealing induced changes on the contact of Ni/Au to N-doped ZnO

N-doped p-type ZnO (p ∼ 10¹⁸cm^-3) was grown on sapphire(0 0 0 1) substrate by metal-organic chemical vapor deposition method. Ni/Au metal was evaporated on the ZnO film to form contacts. As-deposited contacts were rectifying while ohmic behavior was achieved after thermally annealing the contacts in nitrogen environment. Specific contact resistance was determined by circular transmission line method and a minimum specific contact resistance of 8 × 10⁻⁴ Ω cm² was obtained for the sample annealed at 650 °C for 30 s. However, Hall effect measurements indicate that, as the rapid thermal annealing temperature increased up to 550 °C or higher the samples’ conductive type have changed from p-type to n-type, which may be due to the instability nature of the present-day p-type N-doped ZnO or the dissociation of ZnO caused by annealing process in N₂ ambient. Evolution of the sample's electric characteristics and the increment of metal/semiconductor interface states induced by rapid thermal annealing process are supposed to be responsible for the improvement of electrical properties of Au/Ni/ZnO.     

A study on the optical and electrical properties of direct-patternable ZnO films incorporated various contents of Pt nanoparticles

Platinum nanoparticles were synthesized by the methanol reduction method, and their size was controlled to 3 nm on average using PVP [poly(N-vinyl-2-pyrrolidon)] as a protecting unit. Various contents of Pt nanoparticles were incorporated into ZnO solutions which were synthesized by a sol-gel process. ZnO films with Pt nanoparticles of various content were annealed at 500 °C and 600 °C for 1 h. The crystallinity increased with the annealing temperature and also slightly with the content of Pt nanoparticles. The sheet resistance of ZnO films decreased with the incorporation of Pt nanoparticles, however the decreasing behavior was not maintained with increasing content of Pt nanoparticles. A shift of valence band maximum energy of ZnO film with Pt nanoparticles to higher energy was also observed due to electron transfer from Pt nanoparticles to ZnO film. The optical transmittance was 88 ± 2% in the visible region for all the ZnO films. Well-defined 60 μm wide direct-patterned ZnO films containing Pt nanoparticles of 0.5 atomic percent could be formed without using dry etching process.     

Donor-acceptor pair luminescence in nitrogen-doped ZnO films grown on lattice-matched ScAlMgO4 (0001) substrates

We have grown nitrogen-doped ZnO (ZnO:N) films by laser molecular-beam epitaxy. The use of lattice-matched ScAlMgO₄ substrates prevented the degradation of crystallinity induced by the nitrogen incorporation to the films. Despite this improvement, we have not obtained ZnO:N films which showed p-type conductivity. We studied the optical properties of these ZnO:N films. Donor-acceptor pair (DAP) luminescence was observed. The results indicate the formation of an acceptor state. The energy position of the DAP luminescence is lower than that reported by Look et al. [Appl. Phys. Lett. 81 (2002) 1830]. The DAP luminescence band shifts to lower energy with increasing nitrogen concentration. A photoluminescence recombination possibly due to the free-electron-to-acceptor (FA) transition was observed at temperatures higher than 40 K. The acceptor ionization energy was estimated from the energy position of the FA luminescence to be 266 meV.     

The influence of the substrate temperature on the photovoltaic properties of spray-deposited CdS:In thin films

Polycrystalline and highly transparent CdS:In thin films were produced by the spray pyrolysis (SP) technique at different substrate temperatures ranging from 350 to 490 °C on glass substrates. The effect of the substrate temperature on the photovoltaic properties of the films was investigated by studying the transmittance measurements, X-ray diffraction (XRD) patterns, scanning electron microscope (SEM) observations and the I-V plots. The transmittance measurements were used to estimate the band gap energy by the linear fit of (αhν)² versus hν. The band gap energy was found to be slightly increasing with the substrate temperature. XRD diffractograms show that a phase transition from the cubic to the hexagonal phase occurs by increasing the substrate temperature, beside more orientation of crystal growth. Also they show that complex cadmium compounds are still present till T_s ≈ 460 °C after which they practically disappear. From the linear I-V plots the resistivity was estimated and found to be strongly decreasing with the substrate temperature.     

Electrical and optical properties of ZnO films prepared by sputtering of ZnO targets containing AlN

ZnO films prepared from the ZnO target containing 2% AlN are transparent irrespective of radio frequency (RF) power. The obtained ZnO films have the carrier density of 3.8 × 10²⁰ cm⁻³ or less and the low mobility of 5.3-7.8 cm²/(V s). In the case of 5% AlN target, ZnO films prepared at 40, 60 and 80 W are transparent, whereas ZnO films prepared at 100 and 120 W are colored. As RF power increases from 40 to 120 W, the carrier density increases straightforwardly up to 5.5 × 10²⁰ cm⁻³ at 100 W and is oppositely reduced to 3.2 × 10²⁰ cm⁻³ at 120 W. In the case of 10% AlN target, ZnO films prepared at 60 W or more are colored, and have the carrier density of 4 × 10²⁰ cm⁻³ or less. The N-concentration in these colored films is estimated to be 1% or less. The Al-concentration in the ZnO films prepared from the 5 and 10% AlN targets is higher than 2%. The carrier density of the ZnO films containing Al and N atoms is nearly equal to that of ZnO films doped with Al atoms alone. There is no evidence in supporting the enhancement of the carrier density via the formation of N-Al_xZn_4−x clusters (4 ≥ x ≥ 2).     

Direct observation of infrared photoluminescence of spray-deposited CdS:In thin films

Infrared photoluminescence spectra (in the range 0.9-1.4 eV) of the as-deposited CdS:In thin films prepared by the spray pyrolysis technique were recorded at different laser powers and different film temperatures in the range 24-130 K. The spectra show an infrared band centred at 1.06 eV, which have a structure and asymmetry. The structure might be attributed to active defect states which are produced through the growth of the film and might be partially due to coupling to longitudinal phonon. Gaussian peaks were used to deconvolute the spectrum by using nonlinear square fit. The Gaussian peaks used in the fit are expected to fit the spectra taken at different laser powers and different temperatures. These results are discussed in view of the importance of CdS as a window layer for photovoltaic heterojunction solar cells.     

Control of a- and c-plane preferential orientations of ZnO thin films

We report orientation-controllable growth of ZnO thin films and their orientation-dependent electrical characteristics. ZnO thin films were deposited on single-crystalline (1 0 0) LaAlO₃ and (1 0 0) SrTiO₃ substrates using pulsed laser deposition (PLD) at different substrate temperatures (400-800 °C). It was found that the orientation of ZnO films could be controlled by using different substrates of single-crystalline (1 0 0) LaAlO₃ and (1 0 0) SrTiO₃. The a-plane () and c-plane (0 0 0 2) oriented ZnO films are formed on LaAlO₃ and SrTiO₃, respectively. In both cases, the degree orientation increased with increasing deposition temperature T_s. Both the surface free energy and the degree of lattice mismatch are ascribed to play an important role for the orientation-controllable growth. Further characterization show that the grain size of the films with both orientations increases for a substrate temperature increase (i.e. from T_s = 400 °C to T_s = 800 °C), whereas the electrical properties of ZnO thin films depend upon their crystalline orientation, showing lower electrical resistivity values for a-plane oriented ZnO films.     

Investigation of p-type behavior in Ag-doped ZnO thin films by E-beam evaporation

Ag-doped ZnO (ZnO:Ag) thin films were grown on glass substrates by E-beam evaporation technique. The structural, electrical and optical properties of the films were investigated as a function of annealing temperature. The films were subjected to post annealing at different temperatures in the range of 350-650 °C in an air ambient. All the as grown and annealed films at temperature of 350 °C showed p-type conduction. The films lost p-type conduction after post annealing treatment temperature of above 350 °C, suggesting a narrow post annealing temperature window for the fabrication of p-type ZnO:Ag films. ZnO:Ag film annealed at 350 °C revealed lowest resistivity of 7.25 × 10⁻² Ω cm with hole concentration and mobility of 5.09 × 10¹⁹ cm⁻³ and 1.69 cm²/V s, respectively. Observation of a free-to-neutral-acceptor (e,A^o) and donor-acceptor-pair (DAP) emissions in the low temperature photoluminescence measurement confirms p-type conduction in the ZnO:Ag films.     

Optical properties of p-type ZnO doped by lithium and nitrogen

A lithium and nitrogen doped p-type ZnO (denoted as ZnO: (Li, N)) film was prepared by RF-magnetron sputtering and post annealing techniques with c-Al₂O₃ as substrate. Its transmittance was measured to be above 95%. Three dominant emission bands were observed at 3.311, 3.219 and 3.346 eV, respectively, in the 80 K photoluminescence (PL) spectrum of the p-type ZnO:(Li, N), and are attributed to radiative electron transition from conduction band to a Li_Zn-N complex acceptor level (eFA), radiative recombination of a donor-acceptor pair and recombination of the Li_Zn-N complex acceptor bound exciton, respectively, based on temperature-dependent and excitation intensity-dependent PL measurement results. The Li_Zn-N complex acceptor level was estimated to be about 126 meV above the valence band by fitting the eFA data obtained in the temperature-dependent PL spectra.     

The electrical, optical and magnetic properties of Si-doped ZnO films

In this paper, the influences of Si-doping on electrical, optical and magnetic properties of ZnO films have been systematically investigated. It is found that the resistivity of the films decreases from 3.0 × 10³ to 6.2 × 10^-2 Ωcm with Si-doping due to the increase of carrier concentration. The bandgap of ZnO films increases from 3.28 to 3.52 eV with increasing of Si concentration, which is found to be due to the collective effects of bandgap narrowing and Burstein-Moss effect induced by high carrier concentration. With increase of Si concentration, the near band edge (NBE) emission decreases due to the deterioration of crystal quality, while the yellow emission enhances due to the increase of extrinsic impurity or defects. The additional Si-doping has a profound influence on the enhancement of magnetic property and the maximum magnetic moment of 2.6 μ_B/Si is obtained. The ferromagnetic ordering is seen to be correlated with carrier concentration and structural defects.     

Effect of substrate temperature on the structural and optical properties of ZnO and Al-doped ZnO thin films prepared by dc magnetron sputtering

ZnO and Al-doped ZnO(ZAO) thin films have been prepared on glass substrates by direct current (dc) magnetron sputtering from 99.99% pure Zn metallic and ZnO:3 wt%Al₂O₃ ceramic targets, the effects of substrate temperature on the crystallization behavior and optical properties of the films have been studied. It shows that the surface morphologies of ZAO films exhibit difference from that of ZnO films, while their preferential crystalline growth orientation revealed by X-ray diffraction remains always the (0 0 2). The optical transmittance and photoluminescence (PL) spectra of both ZnO and ZAO films are obviously influenced by the substrate temperature. All films exhibit a transmittance higher than 86% in the visible region, while the optical transmittance of ZAO films is slightly smaller than that of ZnO films. More significantly, Al-doping leads to a larger optical band gap (E_g) of the films. It is found from the PL measurement that near-band-edge (NBE) emission and deep-level (DL) emission are observed in pure ZnO thin films. However, when Al was doped into thin films, the DL emission of the thin films is depressed. As the substrate temperature increases, the peak of NBE emission has a blueshift to region of higher photon energy, which shows a trend similar to the E_g in optical transmittance measurement.     

Parallel syntheses and thermoelectric properties of Ce-doped SrTiO3 thin films

Thermoelectric properties of single crystalline Ce_xSr_1−xTiO₃ films (0 ≤ x ≤ 0.5) have been studied by using combinatorial pulsed-laser deposition. Temperature gradient method was used for identifying an optimum growth temperature for SrTiO₃ homoepitaxial growth, at which both oxygen stoichiometry and persisting layer-by-layer growth mode could be accomplished. Electrical conductivity (σ) and Seebeck coefficient (S) were measured at room temperature for the composition-spread films grown at the optimized temperature and found to be considerably higher than those reported for bulk poly-crystalline compounds. Hall measurement revealed that carrier density linearly increased with increasing x, suggesting that a trivalent Ce ions substituted divalent Sr ions to supply electrons. A maximum power factor (S²σ) was obtained for the x = 0.2 film, being 7 and 14 μW/K² cm at 300 and 900 K, respectively.     

Fabrication of high hole-carrier density p-type ZnO thin films by N-Al co-doping

In order to obtain p-type ZnO thin films, effect of atomic ratio of Zn:N:Al on the electronic and structural characteristic of ZnO thin films was investigated. Hall measurement indicated that with the increase of Al doping, conductive type of as-grown ZnO thin films changed from n-type to p-type and then to n-type again, reasons are discussed in details. Results of X-ray diffraction revealed that co-doped ZnO thin films have similar crystallization characteristic (0 0 2 preferential orientation) like that of un-doping. However, SEM measurement indicated that co-doped ZnO thin films have different surface morphology compared with un-doped ZnO thin films. p-type ZnO thin films with high hole concentration were obtained on glass (4.6 × 10¹⁸ cm⁻³) and n-type silicon (7.51 × 10¹⁹ cm⁻³), respectively.     

Optical properties of Al-doped ZnO thin films by ellipsometry

Al-doped ZnO thin films (AZO) were prepared on Si (1 0 0) substrates by using sub-molecule doping technique. The Al content was controlled by varying Al sputtering time. The as-prepared samples were annealed in vacuum chamber at 800 °C for 30 min. From the XRD observations, it is found that all films exhibit only the (0 0 2) peak, suggesting that they have c-axis preferred orientation. The average transmittance of the visible light is above 80%. Spectroscopic ellipsometry was used to extract the optical constants of the films. The absorption coefficient and the energy gap were then calculated. The results show that the absorption edge initially blue-shifts and then red-shifts with increase of Al content.     

Identification of Acceptor States in Li-N Dual-Doped p-Type ZnO Thin Films

Li-N dual-doped p-type ZnO （ZnO：（Li, N）） thin films are prepared by pulsed laser deposition. The optical properties are studied using temperature-dependent photoluminescence. The Lizn-No complex acceptor with an energy 1evel of 138 me V is identified from the free-to-neutral-acceptor （e, A0 ） emission. The Haynes factor is about 0.087 for the Lizn-No complex acceptor, with the acceptor bound-exciton binding energy of 12meV. Another deeper acceptor state located at 248 meV, also identified from the （e, A0） emission, is attributed to zinc vacancy acceptor. The two acceptor states might both contribute to the observed p-type conductivity in ZnO：（Li,N）.