基于二氧化硅荧光纳米颗粒与核酸染料SYBRGreenⅠ的双色显微成像技术用于E.coliO157:H7的检测

将免疫荧光纳米标记技术与激光共聚焦显微成像方法相结合,发展了一种基于二氧化硅荧光纳米颗粒和核酸染料SYBR Green Ⅰ的双色显微成像技术用于大肠杆菌O157:H7的检测.采用联吡啶钌(RuBpy)二氧化硅荧光纳米颗粒对羊抗大肠杆菌O157:H7抗体进行修饰,基于抗体-抗原相互作用实现了其对目标大肠杆菌O157:H7...     

纳米金标记抗体增强SPR检测大肠杆菌O157∶H7

将金纳米粒子(AuNPs)标记的大肠杆菌O157∶H7(E.coli O157∶H7)的多克隆抗体(PAb)作为二抗,采用氨基偶联法将PAb固定在传感器表面作为一抗,通过三明治方法用双通道表面等离子体子共振(SPR)传感器对E.coli O157∶H7进行检测,并与SPR直接法检测进行了比较.结果表明,直接法的检出限为103cfu/mL,线性范围为103～109cfu/mL;AuNPs增强三明治法的检出限为10 cfu/mL,线性范围为10～1010cfu/mL,灵敏度比直接法提高了100倍,且具有更宽的检测范围.本方法不仅检测时间短,而且具有良好的选择性和重现性.     

An anti E. coli O157:H7 antibody-immobilized microcantilever for the detection of Escherichia coli (E. coli).

A silicon microcantilever sensor was developed for the detection of Escherichia coli O157:H7. The microcantilever was modified by anti-E. coli O157:H7 antibodies on the silicon surface of the cantilever. When the aquaria E. coli O157:H7 positive sample is injected into the fluid cell where the microcantilever is held, the microcantilever bends upon the recognition of the E. coli O157:H7 antigen by the antibodies on the surface of the microcantilever. A negative control sample that does not contain E. coli O157:H7 antigen did not cause any bending of the microcantilever. The detection limit of the sensor was 1 x 10(6) cfu/mL when the assay time was < 2 h.     

Reveal E. coli 2.0 method for detection of Escherichia coli O157:H7 in raw beef

Reveal E. coli 2.0 is a new lateral-flow immunodiagnostic test for detection of E. coli O157:H7 and O157:NM in raw beef trim and ground beef. Compared with the original Reveal E. coli O157:H7 assay, the new test utilizes a unique antibody combination resulting in improved test specificity. The device architecture and test procedure have also been modified, and a single enrichment protocol was developed which allows the test to be performed at any point during an enrichment period of 12 to 20 h. Results of inclusivity and exclusivity testing showed that the test is specific for E. coli serotypes O157:H7 and O157:NM, with the exception of two strains of O157:H38 and one strain of O157:H43 which produced positive reactions. In internal and independent laboratory trials comparing the Reveal 2.0 method to the U.S. Department of Agriculture-Food Safety and Inspection Service reference culture procedure for detection of E. coli O157:H7 in 65 and 375 g raw beef trim and ground beef samples, there were no statistically significant differences in method performance with the exception of a single internal trial with 375 g ground beef samples in which the Reveal method produced significantly more positive results. There were no unconfirmed positive results by the Reveal assay, for specificity of 100%. Results of ruggedness testing showed that the Reveal test produces accurate results even with substantial deviation in sample volume or device incubation time or temperature. However, addition of the promoter reagent to the test sample prior to introducing the test device is essential to proper test performance.     

基于甘露糖功能化的水凝胶用于E.coli O157: H7的检测

利用伴刀豆球蛋白A(Con A)的多价结合能力, 结合水凝胶技术与核酸染色技术发展了一种基于甘露糖功能化的水凝胶检测大肠杆菌(E.coli)O157: H7的方法. 以过硫酸铵(APS)为催化剂, 四甲基乙二胺(TEMED)为加速剂, 用丙烯酰胺(AAm)、N,N-二甲基双丙烯酰胺和N-丙烯酰氧琥珀酰亚胺(NAS)合成水凝胶, 通过氨基化甘露糖与NAS发生交联反应, 制备了甘露糖功能化的水凝胶. 当甘露糖功能化的水凝胶加入与Con A共孵育后的菌悬液中时, 由于Con A既能与甘露糖特异性结合, 又能与E.coli O157: H7表面的O-抗原发生免疫反应而紧密连接, 使目标菌被捕获到水凝胶表面, 采用核酸染料SYBR Green Ⅰ对捕获细菌进行染色, 实现了对E.coli O157: H7的核酸标记, 最后通过活体荧光成像系统对水凝胶进行荧光成像, 从而实现对待测样品的检测. 研究结果表明, 该方法可应用于缓冲液体系和混合细菌样品中E.coli O157: H7的特异性检测, 且整个检测步骤包括样品预处理可在2 h内完成. 该方法成本低、易操作, 且具有较好的灵敏度, 可检出3.7×10¹ Cells/mL的目标细菌样品.     

DNA detection on lateral flow test strips: enhanced signal sensitivity using LNA-conjugated gold nanoparticles

A lateral flow test strip assay, enabling sensitive detection of DNA specific to the foodborne pathogen E. coli O157:H7, is described. The use of LNA-conjugated gold nanoparticle probes, along with signal amplification protocols, results in minimum detectable concentrations of ~0.4 nM.     

Comparative validation study to demonstrate the equivalence of a minor modification to AOAC methods 996.09, Vip for EHEC and 996.10, assurance Eia EHEC with the reference culture method for the detection of Escherichia coli O157:H7 in beef

The Visual Immunoprecipitate Assay (VIP) method for the detection of enterohemorrhagic Escherichia coli O157:H7 (VIP for EHEC) and Assurance Enzyme Immunoassay (EIA) method for the detection of EHEC (EHEC EIA) are AOAC INTERNATIONAL Official Methods 996.09 and 996.10, respectively. A minor modification to the enrichment medium used in both methods has been developed. This modification, the BioControl modified EHEC medium (BioControl mEHEC) provides a more cost-effective procedure with performance equivalent to that of the cultural method for detection of E. coli O157:H7 in beef.     

Double interdigitated array microelectrode-based impedance biosensor for detection of viable Escherichia coli O157:H7 in growth medium

Double interdigitated array microelectrodes (IAM)-based flow cell was developed for an impedance biosensor to detect viable Escherichia coli O157:H7 cells after enrichment in a growth medium. This study was aimed at the design of a simple flow cell with embedded IAM which does not require complex microfabrication techniques and can be used repeatedly with a simple assembly/disassembly step. The flow cell was also unique in having two IAM chips on both top and bottom surfaces of the flow cell, which enhances the sensitivity of the impedance measurement. E. coli O157:H7 cells were grown in a low conductivity yeast-peptone-lactose-TMAO (YPLT) medium outside the flow cell. After bacterial growth, impedance was measured inside the flow cell. Equivalent circuit analysis indicated that the impedance change caused by bacterial growth was due to double layer capacitance and bulk medium resistance. Both parameters were a function of ionic concentration in the medium, which increased during bacterial growth due to the conversion of weakly charged substances present in the medium into highly charged ions. The impedance biosensor successfully detected E. coli O157:H7 in a range from 8.0 to 8.2x10(8)CFUmL(-1) after an enrichment growth of 14.7 and 0.8h, respectively. A logarithmic linear relationship between detection time (T(D)) in h and initial cell concentration (N(0)) in CFUmL(-1) was T(D)=-1.73logN(0)+14.62, with R(2)=0.93. Double IAM-based flow cell was more sensitive than single IAM-based flow cell in the detection of E. coli O157:H7 with 37-61% more impedance change for the frequency from 10Hz to 1MHz. The double IAM-based flow cell can be used to design a simple impedance biosensor for the sensitive detection of bacterial growth and their metabolites.     

Escherichia coli O157:H7 detection limit of millimeter-sized PZT cantilever sensors is 700 cells/mL.

A composite self-excited millimeter-sized lead zirconate titanate (PZT) glass cantilever (2 mm x 1.8 mm; sensing area of 6 mm2) was fabricated for the detection of Escherichia coli (E. coli) O157:H7. The fundamental and second mode resonance in air was 10.95 +/- 0.05 kHz and 43.45 +/- 0.05 kHz, respectively. Affinity purified monoclonal antibody (anti-E. coli O157:H7) specific to the pathogen E. coli O157:H7 was immobilized at the cantilever glass tip, and then immersed in liquid containing the pathogen (70 to 7 x 10(7) cells/mL). The resonant frequency showed a reduction and reached a steady state shift of 0 +/- 5, 46 +/- 5, 260 +/- 5, and 1010 +/- 5 Hz corresponding to 0, 700, 7000, and 7 x 10(7) cells/mL. From the experiments conducted, the detection limit of the sensor was 700 cells/mL.     

Modification of the BAX System PCR assay for detecting Salmonella in beef, produce, and soy protein isolate. Performance Tested Method 100201

The BAX System PCR assay for Salmonella detection in foods was previously validated as AOAC Research Institute (RI) Performance Tested Method (PTM) 100201. New studies were conducted on beef and produce using the same media and protocol currently approved for the BAX System PCR assay for E. coli O157:H7 multiplex (MP). Additionally, soy protein isolate was tested for matrix extension using the U.S. Food and Drug Administration-Bacteriological Analytical Manual (FDA-BAM) enrichment protocols. The studies compared the BAX System method to the U.S. Department of Agriculture culture method for detecting Salmonella in beef and the FDA-BAM culture method for detecting Salmonella in produce and soy protein isolate. Method comparison studies on low-level inoculates showed that the BAX System assay for Salmonella performed as well as or better than the reference method for detecting Salmonella in beef and produce in 8-24 h enrichment when the BAX System E. coli O157:H7 MP media was used, and soy protein isolate in 20 h enrichment with lactose broth followed by 3 h regrowth in brain heart infusion broth. An inclusivity panel of 104 Salmonella strains with diverse serotypes was tested by the BAX System using the proprietary BAX System media and returned all positive results. Ruggedness factors involved in the enrichment phase were also evaluated by testing outside the specified parameters, and none of the factors examined affected the performance of the assay.     

一种实用的基于化学发光和磁性纳米颗粒的E.coli O157:H7免疫鉴定方法

化学发光磁酶免疫已经被应用于检测病原体,但是由于针对相应病原体的抗体筛选和修饰等的步骤耗时费力,不适于对多种病原体进行筛查.制备了兔抗大肠杆菌(E.coli)O157:H7的免疫磁性纳米颗粒,富集病原菌后与鼠抗E.coli O157:H7的单克隆抗体形成双抗夹心,采用碱性磷酸酶标记的马抗鼠IgG与单抗结合,加入碱性磷酸酶的化学发光底物试剂3-(2'-螺旋金刚烷)-4-甲氧基-4-(3'-羟基)苯-1,2-二氧杂环丁烷磷酸检测化学发光.实验研究了底物缓冲液、碱性磷酸酶浓度对化学发光强度的影响,比较了NaBH4和甘氨酸对免疫磁珠剩余活性醛基的封闭效果以及本方法检测E.coli O157:H7的特异性和敏感性.结果表明,碱性磷酸酶与底物在c缓冲液中反应的化学发光强度最高,碱性磷酸酶浓度决定了化学发光的强度和持续时间,NaBH4对活性醛基的封闭效果优于甘氨酸,以D群宋内氏志贺氏菌、B群福氏志贺氏菌、鼠伤寒沙门氏菌、金黄色葡萄球菌和霍乱弧菌及E.coli Top10f'为对照的比较实验显示,该检测方法具有良好的特异性,以1mL的菌液为检测体积时对E.coli O157:H7的检测灵敏度为103cell/mL,整个方法的检测时间约为3h.该方法适用于对多样本进行筛查.     

Quantum dot enabled detection of Escherichia coli using a cell-phone

We report a cell-phone based Escherichia coli (E. coli) detection platform for screening of liquid samples. In this compact and cost-effective design attached to a cell-phone, we utilize anti-E. coli O157:H7 antibody functionalized glass capillaries as solid substrates to perform a quantum dot based sandwich assay for specific detection of E. coli O157:H7 in liquid samples. Using battery-powered inexpensive light-emitting-diodes (LEDs) we excite/pump these labelled E. coli particles captured on the capillary surface, where the emission from the quantum dots is then imaged using the cell-phone camera unit through an additional lens that is inserted between the capillary and the cell-phone. By quantifying the fluorescent light emission from each capillary tube, the concentration of E. coli in the sample is determined. We experimentally confirmed the detection limit of this cell-phone based fluorescent imaging and sensing platform as ～5 to 10 cfu mL(-1) in buffer solution. We also tested the specificity of this E. coli detection platform by spiking samples with different species (e.g., Salmonella) to confirm that non-specific binding/detection is negligible. We further demonstrated the proof-of-concept of our approach in a complex food matrix, e.g., fat-free milk, where a similar detection limit of ～5 to 10 cfu mL(-1) was achieved despite challenges associated with the density of proteins that exist in milk. Our results reveal the promising potential of this cell-phone enabled field-portable and cost-effective E. coli detection platform for e.g., screening of water and food samples even in resource limited environments. The presented platform can also be applicable to other pathogens of interest through the use of different antibodies.     

A sensitive lateral flow biosensor for Escherichia coli O157:H7 detection based on aptamer mediated strand displacement amplification

Foodborne diseases caused by pathogens are one of the major problems in food safety. Convenient and sensitive point-of-care rapid diagnostic tests for food-borne pathogens have been a long-felt need of clinicians. Commonly used methods for pathogen detection rely on conventional culture-based tests, antibody-based assays and polymerase chain reaction (PCR)-based techniques. These methods are costly, laborious and time-consuming. Herein, we present a simple and sensitive aptamer based biosensor for rapid detection of Escherichia coli O157:H7 (E. coli O157:H7). In this assay, two different aptamers specific for the outmembrane of E. coli O157:H7 were used. One of the aptamers was used for magnetic bead enrichment, and the other was used as a signal reporter for this pathogen, which was amplified by isothermal strand displacement amplification (SDA) and further detected by a lateral flow biosensor. Only the captured aptamers on cell membrane were amplified, limitations of conventional DNA amplification based method such as false-positive can be largely reduced. The generated signals (red bands on the test zone of a lateral flow strip) can be unambiguously read out by the naked eye. As low as 10 colony forming units (CFU) of E. coli O157:H7 were detected in this study. Without DNA extraction, the reduced handling and simpler equipment requirement render this assay a simple and rapid alternative to conventional methods.     

Miniature biochip system for detection of Escherichia coli O157:H7 based on antibody-immobilized capillary reactors and enzyme-linked immunosorbent assay

In this work, we report Escherichia coli O157:H7 detection using antibody-immobilized capillary reactors, enzyme-linked immunosorbent assay (ELISA), and a biochip system. ELISA selective immunological method to detect pathogenic bacteria. ELISA is also directly adaptable to a miniature biochip system that utilizes conventional sample platforms such as polymer membranes and glass. The antibody-immobilized capillary reactor is a very attractive sample platform for ELISA because of its low cost, compactness, reuse, and ease of regeneration. Moreover, an array of capillary reactors can provide high-throughput ELISA. In this report, we describe the use of an array of antibody-immobilized capillary reactors for multiplex detection of E. coli O157:H7 in our miniature biochip system. Side-entry laser beam irradiation to an array of capillary reactors contributes significantly to miniaturized optical configuration for this biochip system. The detection limits of E. coli O157:H7 using the ELISA and Cy5 label-based immunoassays were determined to be 3 and 230 cells, respectively. This system shows capability to simultaneously monitor multifunctional immunoassay and high sensitive detection of E. coli O157:H7.     

Bead-Based Optical Immunoassay Using Quantum-Dot Labeling and Immunocomplex Dissociation for Detection of Escherichia coli O157:H7

An immunoassay for Escherichia coli O157:H7 using quantum-dot (QD) labeling and subsequent release of the QD labels from immunocomplexes has been developed. The assay principle is that anti-E. coli O157:H7 conjugated immunomagnetic beads are used to capture E. coli O157:H7; this is followed by the binding of QD labeled antibodies to form sandwich immunocomplexes (Bead-Cell-QD); a dissociation buffer then elutes QDs from immunocomplexes by denaturing antibody or lysing cell; the fluorescence signal of the eluted QDs is measured to quantify E. coli O157:H7. This proposed approach avoids the interference of bead autofluorescence in signal transduction and, thus, enhances the detection resolution, while keeping the fast magnetic separation and sandwich binding of two selective antibodies for high specificity.     

Detex for detection of Escherichia coli O157 in raw ground beef and raw ground poultry.

A method for detection of Escherichia coli O157 in beef and poultry is presented. The method is antibody-based and uses a patented antibody-specific metal-plating procedure for the detection of E. coli O157 in enriched meat samples. Both raw ground beef and raw ground poultry were tested as matrixes for the organism. The sensitivity and specificity of the assay were 98 and 90%, respectively. The accuracy of the assay was 96%. Overall, the method agreement between the E. coli O157 Detex assay and the U.S. Department of Agriculture/Food Safety Inspection Service method was 96%. Sample temperature upon loading of the apparatus was critical to the observed false-positive rate of the system.     

Detection of Escherichia coli O157:H7 bacteria by a combination of immunofluorescent staining and capillary electrophoresis

As the number of incidents of bacterial infections continues to rise around the globe, simpler, faster, and more sensitive diagnostic techniques are required to improve the safety of the food supply and to screen for potential bacterial infections in humans. We present here direct and indirect approaches for the detection of bacteria, which are based upon a combination of immunofluorescent staining and capillary electrophoresis. In the direct approach, Escherichia coli O157:H7 bacteria stained with fluorescein-tagged specific antibodies are detected by CE, while in the indirect approach fluorescein-tagged specific antibodies to E. coli are first captured by E. coli O157:H7 bacteria and then released and detected by CE. We have identified suitable bacteria staining and CE protocols, which involved a 10 mM Tris-borate-EDTA (TBE) buffer, 0.25 micro g antibody/1 million bacteria, and capillaries dynamically coated with poly-N-hydroxyethylacrylamide (polyDuramide). We have also successfully detected the presence of E. coli O157:H7 in contaminated meat. The total time required for analysis was 6-8 h, which is less than that realized in most commercial assays presently available.     

Evaluation of the assurance GDS for E. coli O157:H7 method and assurance GDS for shigatoxin genes method in selected foods: collaborative study

A multilaboratory collaborative study was conducted to compare the Assurance GDS for E. coli 0157:H7 method and the reference culture methods for the detection of E. coli 0157:H7 in orange juice, raw ground beef, and fresh lettuce. A separate companion assay, the Assurance GDS for Shigatoxin Genes method was also evaluated with the same test portions. Fifteen laboratories participated in the study. A Chi square analysis of each of the 3 food types at the high, low, and uninoculated control levels was performed. For all foods, the Assurance GDS for E. coli O157:H7 method and the Assurance GDS for Shigatoxin Genes method were equivalent to or better than the reference methods.     

Quantum dot-based array for sensitive detection of <Emphasis Type="Italic">Escherichia coli</Emphasis>

A fluorescent quantum dot-based antibody array, used in sandwich format, has been developed to detect Escherichia coli O157:H7. Numerous parameters such as solid support, optimal concentration of immunoreagents, blocking reagents, and assay time were optimized for array construction. Quantum dot-conjugated anti-IgG was used as the detecting system. The array allows the detection of E. coli O157:H7 at concentrations below 10 CFU mL⁻¹ without sample enrichment, exhibiting an increase of three orders of magnitude in the limit of detection compared to ELISA. The interference caused by Gram (+) and Gram (−) bacteria was negligible at low concentrations of bacteria.     

化学发光磁酶免疫法检测O157:H7大肠埃希菌

通过自行制备的免疫磁珠结合新型发光底物(AMPPD), 改进了化学发光磁酶免疫检测法, 对人工猪肉样品中O157:H7大肠埃希菌进行了检测, 并与人工计数法进行了比较.