Optical characterization of poly (ethylene oxide)/zinc oxide thin films

The optical characterization of poly (ethylene oxide)/zinc oxide thin films has been done by analyzing the absorption spectra in the spectral wavelength region 380–800 nm using a ultraviolet-spectrophotometer at room temperature. Thin film polymer composites made of poly (ethylene oxide) (PEO) containing zinc oxide (ZnO) filler concentrations (0%, 2%, 6%, 10%, and 14%) by weight were used in this study. The optical results obtained were analyzed in terms of the absorption formula for non-crystalline materials. The optical energy gap and other basic optical constants such as dielectric constants and optical conductivity were investigated and showed a clear dependence on the ZnO filler concentration. It was found that the optical energy gap for the composite films is less than that for the neat PEO, and that it decreases as the ZnO concentration increases. Enhancement of the optical conductivity was observed with increase in the ZnO concentration. Dispersion of refractive index was analyzed using the Wemple–DiDomenico single oscillator model. The refractive index (n), extinction coefficient (k), and dispersion parameters (E_o, E_d) were calculated for the investigated films.     

Absorption edge and optical constants of Tl2Ga2S3Se crystals from reflection and transmission,and ellipsometric measurements

The optical properties of Tl₂Ga₂S₃Se layered crystalline semiconductors were investigated from transmission, reflection and ellipsometric measurements. The experimental results of the room temperature transmission and reflection measurements performed in the wavelength range of 400–1100 nm showed the presence of both indirect and direct transitions in the band structure of the crystals with 2.38 and 2.62 eV band gap energies.     

四方晶系SBN晶体吸收边与Ep,Eg的研究

本文通过能实验测量了Ｓｒ０．６３Ｂａ０．３７Ｎｂ２Ｏ６晶体吸收光谱，由透射率曲线计算了吸收系数；并通过对ａ１／２－ｈｖ曲线特征的研究，肯定了３．５ｅＶ以下吸收边的间接跃迁性质，确定了声子的能量Ｅｐ与禁带宽度Ｅｇ。     

Electrical and optical characterization of (PEO+PVAc) polyblend films

Solid polymer blend films based on polyethylene oxide and polyvinyl acetate (PVAc) were prepared in various concentrations by solution cast technique. The features of complexation of the blend films were studied by X-ray diffraction. The electrical conductivity of films was found to increase with increasing PVAc concentration. The conductivity–temperature plots were found to follow Arrhenius nature and showed a decrease in activation energy with increasing PVAc concentration. Optical properties like absorption edge and direct and indirect band gaps were estimated for pure and blend films from their optical absorption spectra. It was found that the energy gap and band edge values shifted to lower energies on blending with PVAc.     

Calculation of the absorption coefficients of optical materials by measuring the transmissivities and refractive indices

In this paper, a formula for accurate calculation of the absorption coefficient of optical material is deduced by the relationship of its transmissivity, refractive index and absorption coefficient. Because the values of transmissivity and refractive index of the optical material with a higher accuracy can be determined by the instruments or obtained directly from the references, the calculated results of the absorption coefficients with a higher accuracy is certified. The absorption coefficients of some optical materials are calculated with it, and the results are discussed.     

Growth, microstructure and electrical properties of sputter-deposited hafnium oxide (HfO2) thin films grown using a HfO2 ceramic target

Hafnium oxide (HfO₂) thin films have been made by radio-frequency (rf) magnetron-sputtering onto Si(1 0 0) substrates under varying growth temperature (T_s). HfO₂ ceramic target has been employed for sputtering while varying the T_s from room temperature to 500 °C during deposition. The effect of T_s on the growth and microstructure of deposited HfO₂ films has been studied using grazing incidence X-ray diffraction (GIXRD), and high-resolution scanning electron microscopy (HR-SEM) coupled with energy dispersive X-ray spectrometry (EDS). The results indicate that the effect of T_s is significant on the growth, surface and interface structure, morphology and chemical composition of the HfO₂ films. Structural characterization indicates that the HfO₂ films grown at T_s < 200 °C are amorphous while films grown at T_s > 200 °C are nanocrystalline. An amorphous-to-crystalline transition occurs at T_s = 200 °C. Nanocrystalline HfO₂ films crystallized in a monoclinic structure with a (−1 1 1) orientation. An interface layer (IL) formation occurs due to reaction at the HfO₂-Si interface for HfO₂ films deposited at T_s > 200 °C. The thickness of IL increases with increasing T_s. EDS at the HfO₂-Si cross-section indicate that the IL is a (Hf, Si)-O compound. The electrical characterization using capacitance-voltage measurements indicate that the dielectric constant decreases from 25 to 16 with increasing T_s. The current-voltage characteristics indicate that the leakage current increases significantly with increasing T_s due to increased ILs.     

Electrical,optical, and structural characterization of polymer blend (PVC/PMMA) electrolyte films

Ion-conducting solid polymer blend electrolytes based on polyvinyl chloride (PVC)/poly methyl methacrylate (PMMA) complexed with sodium perchlorate (NaClO₄) were prepared in various concentrations by solution cast technique. The features of complexation of the electrolytes were studied by X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy. DC conductivity of the films was measured in the temperature range 303–398 K. Transference number measurements were carried out to investigate the nature of charge transport in the polymer blend electrolyte system. The electrical conductivity increased with increasing dopant concentration, which is attributed to the formation of charge transfer complexes. The polymer complexes exhibited Arrhenius type dependence of conductivity with temperature. In the temperature range studied, two regions with different activation energies were observed. Transference number data showed that the charge transport in this system is predominantly due to ions. Optical properties like absorption edge, direct band gap, and indirect band gap were estimated for pure and doped films from their optical absorption spectra in the wavelength region 200–600 nm. It was found that the energy gap and band edge values shifted to lower energies on doping with NaClO₄ salt. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamil Nadu, India, Dec. 7–9, 2006.     

Dielectric permittivity and electric modulus of polyethylene oxide (PEO)-LiClO4 composite electrolytes

Dielectric permittivity and conductivity relaxation in polyethylene oxide (PEO)-LiClO₄ salt polymer electrolytes have been investigated for different lithium ion concentrations. We have observed that imaginary modulus spectra exhibit asymmetric maxima with peak-width much broader than that of the Debye peak and are skewed toward the high frequency sides of the maxima. The charge carriers for the electrolyte having higher lithium salt concentration relax much faster than that for other electrolytes and produces higher conductivity. The modulus data have been fitted using non-exponential Kohlrausch-Williams-Watts (KWW) function φ(t). We have observed that the value of the non-exponential parameter (β) is fairly low and nearly constant for different salt concentrations. The low value of β suggests a wide distribution of non-exponential relaxation times. Using the scaling of modulus data we have observed that the relaxation dynamics of charge carriers in these PEO-Li salt based electrolytes is independent of temperature and salt concentration.     

Dielectric and leakage current properties of Li doped (Ba,Sr)TiO3 thick film interdigital capacitors on the alumina substrates

Li doped (Ba,Sr)TiO₃ thick films were fabricated by employing the screen printing method on the alumina (Al₂O₃) substrates. Interdigital capacitor patterns with seven fingers of 200 μm gap, 250 μm length were designed and screen printed on the alumina substrates. Ba_0.5Sr_0.5TiO₃ materials, paraelectric state at the room temperature, have been chosen for the microwave devices due to high dielectric permittivity and low loss tangent, however, the sintering temperature of (Ba,Sr)TiO₃ is over 1350 °C. In order to lower the sintering temperature, Li (3 wt%) was added to the (Ba,Sr)TiO₃ materials. Li doped (Ba,Sr)TiO₃ thick films screen printed on the alumina (Al₂O₃) substrates were sintered at 900 °C for 1.5 h. The structural feature was analyzed with X-ray diffraction method. Temperature dependent dielectric properties were characterized from 303 to 403 K at 1 MHz. Within the ±100 V of bias voltage, current-voltage characteristics of Li doped (Ba,Sr)TiO₃ films were investigated from 303 to 403 K. Through the current-voltage characteristics, the resistivity of Li doped (Ba,Sr)TiO₃ films were calculated.In this paper, the significant negative temperature coefficient of resistance (NTCR) of Li doped (Ba,Sr)TiO₃ films will be presented through the activation energy fitting. Measured activation energy is approximately 0.366 eV.     

Optical absorption and spectrophotometric studies on the optical constants and dielectric of poly (o-toluidine) (POT) films grown by spin coating deposition

In this work, a poly(o-toluidine) “POT” was synthesized by chemical oxidative polymerization method in aqueous media. High uniform and good adhesion thin films of POT have been successfully deposited by the spin coating technique. The films were characterized by X-ray diffraction (XRD) and Fourier transforms infrared (FTIR) spectroscopy. The XRD pattern of the POT shows the semi-crystalline nature of the films. FTIR studies show the information of functional groups in POT. The optical transmittance and reflectance of POT film was measured in the 200–2500 nm wavelength range. The absorption coefficient analysis shows that the optical band gaps of POT film are direct allowed transition band gaps with 1.2 and 2.6 eV. Other optical absorption parameters such as extinction molar coefficient, oscillator strength and electric dipole strength were also calculated. The dispersion parameters were determined and discussed based on the single oscillator model. According to the analysis of dispersion curves some important parameters such as dispersion energy (E_d), oscillator energy (E_o), high frequency dielectric constant ₍ε_∞) and lattice dielectric constant (ε_L) were also evaluated. Discussion of the obtained results and their comparison with the previous published data were also given. The obtained desirable results of POT thin film can be useful for the optoelectronic applications.     

Development of polyurethane multiwall carbon nanotubes (MWCNTs) novel polymeric nanodielectric material

Polyurethane/multi-walled carbon nanotube nanodielectric thin films of 25 μm thick were prepared by solution grown method. The microstructure of the nanodielectric was examined by scanning electron microscopy. The MWCNTs are observed to be dispersed in PU matrix well apart from a few of clusters. The MWCNTs/polymer nanodielectrics characterized with decrease in energy band gap and crystallinity. The analysis of dielectric properties of the composite samples of different weight ratio was studied by measuring the permittivity and tangential loss at room temperature. The frequency dependent permittivity obeys the percolation theory. Further, it has been observed that the dielectric properties of PU and PU nanodielectric are unaffected by UV-irradiation. XRD characteristics confirm the formation of PU/MWCNTs nanodielectrics.     

Thickness effect on the structural and optical constants of stibnite thin films prepared by sulfidation annealing of antimony films

This paper deals with some physical properties of antimony sulphide Sb₂S₃ thin films obtained by an annealing process in sulphur vapors at 300 °C of Sb thermal evaporated thin films deposited on glass substrate. The crystal structure and surface morphology were investigated by both XRD and AFM techniques. This structural study shows that Sb₂S₃ thin films were well crystallized in orthorhombic structure and some parameters such as the lattice parameter, crystallite size, microstrain and degree of preferred orientation have been reported and correlated with the effect of crystallite size. On the other hand, the refractive index and the extinction coefficient were discussed in terms of the Forouhi–Bloomer model. The optical band gap was found to range from 1.75 to 2.23 eV. Finally, the analysis of the optical parameters extracted from the Urbach–Martienssen and Forouhi–Bloomer models lead to some explanations of the correlations between the structural properties in terms of the crystallite size and optical ones.     

Influence of MgO on structure and optical properties of alumino-lithium-phosphate glasses

MgO doped lithium alumino phosphate glasses (PLA: P₂O₅+Li₂O+Al₂O₃+MgO) were prepared by melt quenching technique. Raman spectra display three significant peaks at 698, 1164 and 1383 cm⁻¹ attributed to: symmetric stretching vibrations of the bridging oxygen (BO) in the P–O–P chains, symmetric stretching vibrations of the PO₂ groups, and the asymmetric vibrations vas(PO₂) of the non-bridging oxygen (NBO) atoms, respectively. Also, the density, molar volumes and ion concentration have been discussed and correlated with the structural changes within the glassy matrix. Some optical constants such as refractive index and dispersion parameters (E_o: single-oscillator energy and E_d: dispersive energy) of the glasses were determined. Finally, the values of the optical band gap for direct and indirect allowed transitions have been determined from the absorption edge studies. It is deduced that the values of E_opt increase with increasing MgO content. It was assigned to structural changes induced from the formation of non-bridging oxygen. The Urbach energy (ΔE) was found to decrease from 0.578 to 0.339 eV with increasing MgO content from 0.5 to 2 mol.     

An experimental study on the effect of mesoporous silica addition on ion conductivity of poly(ethylene oxide) electrolytes

Solid polymer electrolyte (SPE) composites, which are composed of poly(ethylene oxide) (PEO), mesoporous silica (SBA-15), and lithium salt were prepared in order to investigate the influence of SBA-15 content on the ionic conductivity of the composites. The ionic conductivity of the SPE composites was monitored by frequency response analyzer (FRA), and the crystallinity of the SPE composites was evaluated by using XRD. As a result, the addition of SBA-15 to the polymer mixture inhibited the growth of PEO crystalline domain, due to the mesoporous structure of the SBA-15. Also, the PEO₁₆LiClO₄/SBA-15 composite electrolytes show an increased ion conductivity as a function of SBA-15 content up to 15 wt.%. These ion conductivity characteristics are dependent on crystallinity with SBA-15 content.     

Conductance study of poly(ethylene oxide)- and poly(propylene oxide)-based polyelectrolytes

The ionic conductivity of poly(ethylene oxide) and poly(propylene oxide) in pure solution form, individually complexed with salts of Na⁺ and Li⁺, with and without plasticizer (propylene carbonate) and in blended form with individual salt with and without plasticizer, was studied. The conductance measurements were made at various concentrations of salt polymer complexes and at different temperatures. The effects of temperature and plasticizer concentration were measured from Arrhenius conductance plots. It is shown that the addition of salts in pure PEO increases conductance many times. The plasticizer has also same effect. The blending of PEO with PPO gives enhanced conductivity as compared to pure PEO. The activation energies were determined for all the systems which gave higher values for pure PEO and the value decreases with the addition of Li and Na salts and further decreases with the addition of plasticizer. The blending has also lowered the activation energy values which mean that incorporation of PPO in PEO has decreased crystallinity and the amorphous region has increased the local mobility of polymer chains resulting in lower activation energies.     

Characterization of poly (3-methyl thiophene) thin films prepared by modified chemical bath deposition

Poly (3-methyl thiophene) thin films were prepared by chemical bath deposition technique on glass substrate; the prepared thin films were characterized for structural, morphological and optical properties. The variation in the oxidant concentration has an influence on the properties of the P3MeT thin films. The increase in the oxidant concentration leads to increase in the thickness of the film. The binding energy increases due to increase in oxidation concentration. The P3MeT thin films show smooth surface morphology with increase in oxidant concentration whereas the contact angle of the thin film decreases with increase in oxidant concentration. The optical absorbance of these thin films was found to increase with decrease in the optical band gap due to increase in oxidant concentration.     

Effect of fillers on magnesium–poly(ethylene oxide) solid polymer electrolyte

A solid polymer electrolyte (SPE) film consisting of poly(ethylene oxide) (PEO) with magnesium chloride as electrolytic salt and B₂O₃ as the filler has been prepared by solution casting technique. The polymeric film was flexible and self-standing with proper mechanical strength and studied for application in a solid-state rechargeable magnesium battery. The interactions between the filler and PEO chains are studied by differential scanning calorimeter and Fourier transform infrared techniques. Composition of SPE is optimized, and maximum conductivity is obtained at 2 wt% B₂O₃. Filler seems to increase the number of free magnesium cations by decoordinating the bond between magnesium cations and ether oxygen of PEO. Cyclic voltammetry results show the reversible capability of magnesium electrode. Solid-state magnesium cell employing magnesium anode, SPE, and manganese oxide was assembled, and its open circuit voltage is found to be 1.9 V.     

Dielectric relaxation study of poly(ethylene glycols) using TDR technique

Temperature dependent dielectric relaxation and thermodynamic properties of polyethylene glycols HO[CH₂CH₂O)_nH with number average molecular weight 200 (n = 4), 300 (n = 7), 400 (n = 9) and 600 (n = 14) g mol^− 1 have been studied using Time Domain Reflectometry (TDR) in the frequency range 10 MHz to 20 GHz. The frequency dependence of the complex dielectric permittivity is analyzed by the Havriliak-Negami expression. The static permittivity ε₀, high frequency limiting static permittivity ε_∞, average relaxation time τ₀ and thermodynamic energy parameters such as free energy, enthalpy of activation and entropy of activation have been determined. The average free energy of activation ΔF_τ for PEG molecules was found to be in the range 4-5 kcal mol^− 1. The values of entropy ΔS_τ for PEG-200, PEG-400 and PEG-600 molecules were found to be positive while entropy ΔS_τ for PEG-300 molecules was found negative, which confirms that the configuration of PEG-300 involved in the dipolar orientation has an activated state, which is more ordered than the normal state compared to PEG-200, PEG-400 and PEG-600 molecules.     

More studies on the sulfonated poly(phenylene oxide)+imidazole Brønsted acid-base polymer electrolyte membrane

In this article, we report the synthesis of a serious of proton-conducting polymer electrolytes made of sulfonated poly(phenylene oxide) (SPPO) and imidazole (Im) by tuning the mixing ratios. The samples were labeled by their mole composition as SPPO-xIm, where x is the molar ratio of Im to SPPO repeat unit. These membranes were studied by means of Thermogravimetric-differential thermal analysis (TG-DTA) and scanning electronic microscope (SEM) and investigation of activation energies of the SPPO-xIm at different relative humidity was also performed. TG-DTA curves reveal these SPPO-xIm composite materials had the high thermal stability. The proton conductivity of SPPO-xIm composite material increased with the temperature, and the highest proton conductivity of SPPO-xIm composite materials was found to be 6.92×10⁻³ S/cm at 200 °C under 33% relative humidity (RH) with a “mixing rate” where x=2.     

Behaviour of transmittance and phase change on transmission with film thickness at intermediate thicknesses

The behaviour of the optical functions T (transmittance) and X_t (phase change on transmission) for an absorbing film have been investigated as the film thickness was increased from a small fraction of a wavelength up to a thick solid. When plotted against thickness, the values of T oscillated at a frequency related to the quantity, x=2πd/λ which is equal to the phase thickness divided by the refractive index. Ultimately, for real materials, the oscillations were damped to zero due to the absorption term in the complex dielectric constant of the film material. In the case of X_t, the most notable feature was the sudden phase changes of ±π which occurred repeatedly as the thickness increased and the values of x at which this occurred could be related to the conditions for constructive or destructive interference between light rays coming from the top and bottom of the film.