凸轮与平底从动件的接触变形与接触刚度计算

将凸轮与平底从动件接触视为二维线性接触,基于无限大半空间模型对从动件的变形量进行了分析,利用圆柱体二维线接触变形的计算方法对凸轮接触变形进行了计算,从而得到了凸轮与平底从动件的接触变形量与接触刚度理论计算公式。利用Palmgren公式和有限元方法对计算公式进行了验证,并分析了接触刚度与凸轮曲率半径、接触力之间的关系,结果表明:接触应力、接触半宽、凸轮接触变形量的理论计算值与有限元计算结果几乎相等,凸轮与从动件的接触变形量之和的理论计算值与有限元计算值相差小于5%;凸轮与平底从动件的接触变形之和、接触刚度都与接触处凸轮的曲率半径无关,而与凸轮与平底从动件间的接触力大小有关。     

大变形薄板多体系统的动力学建模

基于非线性弹性理论,考虑剪切应变和横向应变,用绝对节点坐标法建立了大变形矩形薄板的动力学变分方程;为了提高非线性刚度阵的计算效率,根据非线性刚度阵与广义坐标阵的函数关系式,在非线性刚度阵中分离出广义坐标阵,从而避免了每个时间步长的单元刚度阵的积分运算。在此基础上,引入运动学约束关系,建立了大变形薄板系统第一类拉格朗日方程,对重力作用下大变形二连板进行数值仿真。计算结果表明:随着薄板的柔度增大,低频的弯曲变形与高频拉伸变形的耦合愈加显著;此外,系统机械能守恒验证了该模型正确性。     

考虑约束扭转的薄壁梁单元刚度矩阵

推导了薄壁空间梁单元刚度矩阵 ,考虑了双向弯曲及截面约束扭转对杆件轴向变形的影响 ;计算了截面的翘曲变形 ,以及二次剪应力对翘曲变形的影响 ,可适用于任意截面 (包括开口、闭口和混合剖面 )的薄壁杆件。计算结果表明 ,考虑约束扭转的薄壁梁单元刚度矩阵有相当好的精确度 ,可以用于薄壁杆件的静动力分析。     

任意变刚度梁变形的通用方程

<正> 工程实际中常遇到阶梯形和锥形等变截面变刚度梁,求其复杂载荷作用下的变形多采用近似的数值解法.文[1]给出阶梯形变截面梁第 n 段变形的通用方程,需计算各段端点的转角多项式和挠度多项式的值.文[2]采用直接积分法求解变惯矩梁变形,要确定若干积分常数.本文利用 Heaviside 函数,将任意变刚度化为阶梯刚度,导出了任意变刚度梁变形的一种通用方程     

有腹筋混凝土梁的剪切刚度分析模型

钢筋混凝土梁的挠度计算通常不计入剪切变形的贡献,然而对于斜向开裂的有腹筋混凝土梁,斜裂缝会显著降低梁体的有效剪切刚度,导致剪切变形值显著增大,因此在验算评估时应予以考虑.为评价钢筋混凝土梁斜向开裂后的有效剪切刚度,首先,基于变角桁架模型推导了钢筋混凝土梁在箍筋屈服状态下的有效剪切刚度;与弹性剪切刚度比较发现,剪切刚度退化系数的主要影响因素为材料弹模比、配箍率和斜压杆倾角.其次,基于试验剪切变形曲线表现出的刚度退化规律,提出了可用于不同开裂程度下剪切刚度计算的恒定切线刚度退化模式,并采用开裂后的剪力增量作为反映开裂程度的定量指标.最后,根据最小能量原理得到了剪切刚度退化中两个关键参数:斜压杆倾角和剪切刚度退化系数的解析公式.通过2根薄腹混凝土梁剪切变形试验以及收集的15个受剪梁段的剪切变形数据对模型有效性进行了验证,验证结果表明:有腹筋混凝土梁剪切刚度分析模型能较为准确地预测箍筋屈服状态的剪切刚度,并能反映不同开裂程度下的剪切刚度退化规律.     

一种考虑剪切变形的矩形板元素刚度矩阵

本文应用应变能分项插值的概念推导了一种具有12个参数的考虑剪切变形的正交各向异性矩形平板元素的刚度矩阵,在计算应变能的近似值时,对不同的项采取了不同的位移函数.基本的位移函数是根据考虑剪切变形的直梁的位移得到的,其中包含了弯曲刚度与剪切刚度的比值D/C,因此得到的刚度矩阵对各种剪切刚度值直至薄板(C→∞)都能应用.刚度矩阵以显式表示,使用方便.对典型问题的静力、动力计算表明结果是良好的.     

钢-混凝土组合箱梁梁段有限元法研究

组合梁界面滑移将减小组合梁刚度,增大变形,影响构件性能;剪应力沿截面横向分布不均匀,造成其弯曲正应力的横向分布呈曲线形状,即剪力滞效应;同时组合梁往往重载,具有较小的跨高比,剪切变形不可忽略.根据虚功原理,建立了同时考虑滑移效应、剪力滞及剪切变形效应的组合梁单元刚度矩阵及等效节点力向量,并在此基础上编制了组合梁梁段有限元程序.利用本文程序对现有组合梁试件的混凝土顶板应力、钢梁底板应力、跨中挠度和梁端滑移进行了计算,并将本文计算结果与解析法计算结果及试验结果进行了比较.结果表明,本文计算结果与解析法计算结果及试验结果吻合良好;同时,本文计算结果具有较好的稳定性,验证了本文计算方法的正确性.本文所建立的梁单元刚度矩阵同时考虑了剪切变形、剪力滞及滑移效应的影响,符合工程实际,为有限梁段法分析组合箱梁提供了理论基础.     

THE STRENGTHENING OF AERO-TRANSPORT WITH LARGE OPENING

为了对运输类飞机机身大开口结构进行加强,满足刚度连续变形协调的设计要求,本文对机身大开口结构和完整机身结构的刚度进行了深入研究,首先简化了计算模型,对刚度进行了计算,提出了刚度比的定义,得出刚度比与大开口角度、机身半径、蒙皮厚度以及边梁面积之间的关系表达式,得到运输类飞机机身大开口结构加强的原则和方法,在型号上成功得到了应用,用于指导初期的结构设计.     

曲壁蜂窝夹层板的振动特性研究

曲壁蜂窝具有负刚度特性,可以在大变形过程中吸收能量、抗冲击,并且在冲击过后可以自我恢复而不像传统蜂窝被压溃。本文将曲梁构成的负刚度蜂窝作为芯层,建立夹层板的动力学模型;推导出了曲壁负刚度蜂窝胞元的等效弹性参数,将其周期性排列为蜂窝芯,应用Reddy高阶剪切变形理论、Von-Karman大变形关系和Hamilton原理推导了负刚度蜂窝夹层板的非线性动力学方程;应用Navier法计算了四边简支边界条件下的固有频率。并利用有限元软件ABAQUS建立模型,计算固有频率,与理论计算结果进行比较,结果显示二者的计算结果具有较好的一致性,验证了芯层等效弹性参数及模型的有效性。探讨了在蜂窝胞元具有较高吸能情形下,夹层板在不同芯层厚度、不同芯厚比以及不同胞元曲壁厚度时的固有频率的变化特性。     

非接触式气体润滑密封变形的数值分析

针对离心泵用非接触式螺旋槽气体润滑密封，通过采用有限元法求解描述密封端面间气体流动的雷诺方程，计算了不同约束、不同结构的静密封环和配对动密封环的力变形、端面泄漏量、开启力及气膜刚度等参数，分析了变形对密封特性的影响．结果表明：密封环的力变形使得端面气膜形状大多呈发散型，约束对其变形大小具有重要影响，选择合适的约束可以减小密封面转角、提高气膜刚度、增强密封工作稳定性；变形对密封的开启力影响不大，但变形导致泄漏量增大，并明显改变气膜刚度。     

Shear stability of metallic glasses

The effect of sample size on the shear deformation and compressive plasticity of different metallic glasses were investigated. The experimental results showed that the deformation and fracture behaviors of samples prepared from chemically identical Zr-, Ti-, Fe-, or Mg-based metallic glass ingots were strongly dependent on the sample size and machine stiffness, and a super-high compressive plasticity was achieved in the Zr-based metallic glasses with sample size of 1.0 mm in width. It is also found that the sample size can significantly influence the density of elastic energy dissipated in the shear band: with sample size decreasing and machine stiffness increasing, the density of the elastic energy dissipated in the shear band of metallic glasses is prominently decreased, thus the shear deformation turns to be more stable, resulting in the improvement of plasticity in ductile metallic glasses and the transition from fragmentation fracture to shear fracture in brittle metallic glasses. This finding is important for the potential applications of the present metallic glasses and for designing new metallic glasses with better mechanical properties.     

金属玻璃基复合材料的变形行为及本构关系研究综述

金属玻璃及其复合材料因其优良的力学性能而具有良好的应用前景,相关研究方兴未艾. 本文主要总结国内外的研究成果并结合本课题组的最新研究工作,针对块体金属玻璃基复合材料的变形行为、增韧机理和本构关系研究现状进行较为全面的综述. 首先,对近几十年来在块体金属玻璃基体材料的变形行为与失效机理以及本构关系研究方面的丰硕成果进行简要回顾. 其次,从实验研究和数值模拟两方面,重点对金属玻璃基复合材料的变形行为与失效机理研究成果进行介绍,总结了金属玻璃基复合材料的塑性变形、增韧机理及影响因素. 然后,对金属玻璃基复合材料的本构关系研究最新进展进行评述,重点介绍了均匀化方法在该领域的应用. 作为代表,较为详细地介绍了作者新近提出的一个二次均匀化的方法,并在此基础上,结合纳米孔洞作为自变量的失效判据而建立了本构模型,该模型对金属玻璃基复合材料的变形和失效行为进行了合理预测. 最后,对该领域的研究现状进行简单的总结,并对未来的研究问题进行展望.      

Size effects on tensile and compressive strengths in metallic glass nanowires

Shear localization induced brittleness is the main drawback of metallic glasses which restricts their practical applications. Previous experiments have provided insights on how to suppress shear localization by reducing the sample size of metallic glasses to the order of 100 nm. In order to reveal the size effects and associated deformation mechanisms of metallic glasses in an even finer scale, we perform large-scale atomistic simulations for the uniaxial compression and tension of metallic glass nanowires. The simulation results show that, as the diameter of metallic glass samples decreases from 45 nm to 8 nm, the tensile yield strength increases while the compressive yield strength decreases. Homogeneous flow is observed as the governing deformation mechanism in all simulated metallic glass samples, where plastic shearing tends to initiate on the sample surface and propagate into the interior. To rationalize the size dependence of yield strengths, we propose a theoretical model based on the concept of surface stress and Mohr–Coulomb criterion. The theoretical predictions agree well with the simulation results, implying the important role of surface stress on the yielding of MGs below 100 nm. Finally, a discussion about the size effects of strength in metallic glasses at different length scales is provided. Our results suggest that the shear band energy and surface stress might be the two crucial parameters in determining the critical size required for the transition from shear localization to homogeneous deformation in MGs.     

不同温度下2种钨结构增强Zr基非晶合金的动态压缩性能

利用SHPB装置对钨丝增强Zr基非晶复合材料和钨骨架增强Zr基非晶复合材料进行了3种环境温度下多种应变率的动态压缩性能测试。比较了2种材料的动态力学性能,发现二者均具有应变率敏感性和较强的塑性变形能力。但二者承载机制存在较大差异。钨丝增强结构变形主要表现在钨丝的失稳,由数值模拟初步分析了这种局部结构失稳控制的变形以及热失稳现象;钨骨架增强结构变形前期钨骨架起主要承载作用,而不是各成分的共同作用,这导致材料的屈服强度比纯非晶和纯钨的低。     

汽车玻璃高温蠕变特性的实验与理论研究

通过对汽车用挡风玻璃进行不同温度、不同应力水平下的单轴拉伸蠕变实验,揭示了其非线性蠕变变形特性.实验发现,不同温度和载荷下的蠕变曲线形状类似,高温(550℃～590℃)下该材料的减速蠕变变形不很明显,主要表现为稳态和加速蠕变变形,且其断裂数据符合Monkman-Grant关系,应力和温度对其影响不显著.基于实验结果,本文建立了非线性高温蠕变本构方程.理论预测与实验数据进行了比较,结果表明所提出的本构方程能较好地描述汽车玻璃高温蠕变变形的全过程.     

Notch sensitivity in nanoscale metallic glass specimens: Insights from continuum simulations

Recent experiments have shown that nano-sized metallic glass (MG) specimens subjected to tensile loading exhibit increased ductility and work hardening. Failure occurs by necking as opposed to shear banding which is seen in bulk samples. Also, the necking is generally observed at shallow notches present on the specimen surface. In this work, continuum finite element analysis of tensile loading of nano-sized notched MG specimens is conducted using a thermodynamically consistent non-local plasticity model to clearly understand the deformation behavior from a mechanics perspective. It is found that plastic zone size in front of the notch attains a saturation level at the stage when a dominant shear band forms extending across the specimen. This size scales with an intrinsic material length associated with the interaction stress between flow defects. A transition in deformation behavior from quasi-brittle to ductile becomes possible when this critical plastic zone size is larger than the uncracked ligament length. These observations corroborate with atomistic simulations and experimental results.     

Length scale effects on the shear localization process in metallic glasses: A theoretical and computational study

Some recent experiments on sub-micron and nano-sized metallic glass (amorphous alloy) specimens have shown that the shear localization process becomes more stable and less catastrophic when compared to the response exhibited by large sample sizes. This leads to the discovery that the shear localization process and fracture can be delayed by decreasing sample volume. In this work we develop a non-local and finite-deformation-based constitutive model using thermodynamic principles and the theory of micro-force balance to study the causes for the aforementioned observations. The constitutive model has also been implemented into a commercially available finite-element program by writing a user-material subroutine. With the aid of finite-element simulations, our constitutive model predicts that metallic glass samples have the intrinsic ability to exhibit: (a) the delaying of (catastrophic) shear localization with decreasing sample size, and (b) homogeneous deformation behavior for sample volumes smaller than the shear band nucleus.The cause for the observations listed above is the increasing influence of a non-local interaction stress with decreasing sample volume. This interaction stress has energetic origins and it affects plastic deformation due to the strong coupling between plastic shearing and free-volume generation. Akin to strain-gradient plasticity theory, the role of the interaction stress is to strengthen the material at locations where the defect density/free volume is higher compared to the rest of metallic glass sample.     

块体金属玻璃及其复合材料的压缩剪切特性和侵彻/穿甲“自锐”行为

块体金属玻璃及其复合材料以其优异的力学、物理和化学性能, 正成为国内外科技和工程领域的研究热点. 特别是金属玻璃复合材料具有高剪切敏感性和剪切``自锐'特性, 使其有可能成为新型穿甲弹芯材料, 因而具有重要的军事意义. 本文综述了针对块体金属玻璃及其复合材料的压缩剪切变形和断裂特性及高速冲击、侵彻/穿甲过程中剪切``自锐'行为等方面的研究进展, 包括相关实验研究、理论分析及有限元模拟等, 最后给出未来相关工作的一些建议.      

Uniaxial elongational flow effects and morphology development in LDPE/phosphate glass hybrids

Shear and elongational viscosity measurements were performed on low-density polyethylene/phosphate glass (LDPE/Pglass) hybrid materials in the liquid state. Under shear deformation, the hybrids with low concentrations of Pglass showed a Newtonian region at low frequencies, followed by shear-thinning behavior at high frequencies. High Pglass concentrations displayed shear-thinning behavior over the whole range of frequencies studied. Deviations from the log-additivity rule for viscosity were found to be compositionally dependent and generally indicated an immiscible mixture. The elongational viscosity of the hybrids increased at very low Pglass concentrations (1–2 vol.% Pglass) and then was drastically reduced at higher concentrations (i.e., >10 vol.% Pglass). In addition, elongational flow was found to induce the formation of Pglass fibrils in hybrids containing at least 10 vol.% Pglass. This was correlated to the elongational capillary number; the critical elongational capillary number was estimated to be 0.22. The elongational deformation was also found to greatly increase the overall crystallinity of the system due to molecular orientation of the LDPE polymer chains as confirmed by wide angle X-ray diffraction. A critical composition of 5 vol.% Pglass was found to be the point at which LDPE hybrid rheological properties, molecular orientation, and morphology changed drastically.     

W骨架/Zr基非晶合金复合材料破片侵彻能力与后效研究

将W骨架/Zr基非晶合金复合材料破片装入弹体制备成预制破片弹丸,并进行实爆试验,研究W骨架/Zr基非晶合金复合材料预制破片侵彻靶板的能力,以及预制破片贯穿靶板后对棉被、油箱的引燃能力。结果表明:制备的W骨架/Zr基非晶合金复合材料密度大、强度高,爆炸完整性和侵彻能力能够满足作为榴弹预制破片的要求;W骨架/Zr基非晶合金复合材料破片侵彻过程中自身变形是影响侵彻能力的主要原因之一;W骨架/Zr基非晶合金复合材料预制破片侵彻和贯穿靶板的过程中伴随着强烈的爆轰,当穿透率足够高时,预制破片的爆轰作用能够引燃靶后的棉被和油箱。