阳离子淀粉吸附脱色性能的研究

本文对阳离子淀粉(CST)的吸附性能进行了系统的研究。实验表明阳离子淀粉对各种阴离子染料的吸附,主要是化学吸附。在pH为2～8范围内和室温下,对不同结构的阴离子染料均有一定吸附脱色效果。     

多级流化床吸附的味精脱色除铁研究

本文提出并研究了中和液与结晶母液混合进料,TPCIX柱多级流化混合床吸附的味精脱色除铁新工艺。研究了K15+122混合吸附剂脱色除铁的适宜工艺条件并考察了TPCIX(Tipping Plate Continuous Ion Exchange Contractor)柱的工艺运转。新工艺对提高99％味精产率和总收率,改善技术经济指标具有建设性的意义。     

蚕砂总生物碱提取物的脱色研究

通过动态吸附实验,考察了D296R(-Cl型)、D296R(-OH型)、D2040、X-5、D380(-Cl型)和D380(-OH型)6种树脂对蚕砂提取液的脱色作用,筛选出分离效果较好的树脂并确定了其分离条件,在此基础上使用正交设计法对它进行树脂再生条件的探究。通过对比这6种树脂对色素及活性物质的分离效果,发现D296-R(-Cl型)大孔阴离子交换树脂脱色效果最为理想,以95%乙醇溶液稀释的蚕砂提取液,经该树脂上样分离后,用3BV70%的乙醇溶液洗脱,所得洗脱液吸光度0.1,活性成分保留较多。正交设计法得出该树脂的适宜再生条件:乙醇浓度为80%,流速为3BV/h,NaOH溶液浓度为3%。     

活性艳红X-3B水溶液的光催化脱色及矿化过程研究

对染料活性艳红X-3B水溶液的光催化反应过程进行了初步研究.首先,利用紫外-可见吸收光谱、高效液相色谱和质谱对反应过程中溶液组成的变化进行了测试,并用重铬酸盐法测定了各反应时刻溶液的COD值;其次,使用红外吸收光谱对反应过程中催化剂表面的吸附物种进行了考察.研究结果表明,在本实验条件下,活性艳红X-3B水溶液的光催化脱色和矿化过程是同时进行的,脱色反应完成后,溶液中生成了难以降解的中间产物,致使矿化过程难以继续进行.     

树脂吸附法D-核糖发酵液脱色的研究

首次考察了六种不同树脂对D－核糖发酵液的脱色作用,详细地研究了吸附工艺条件对树脂脱色能力的影响．试验结果表明,在25℃下,以1.0BV／h的流速进行吸附时,NKA－Ⅱ树脂对D－核糖发酵液具有良好的脱色效果,脱色率91％,处理量5.7BV;并对树脂再生的条件进行了较详尽研究。     

树脂吸附法豆腐柴叶果胶提取液脱色的研究(II) 动态法脱色的适宜条件

考察了6种不同树脂对豆腐柴果胶提取液的脱色作用.详细地研究了吸附工艺条件对树脂脱色能力的影响.试验结果表明,在pH为2.0和温度为25℃下,以0.34BV/min流速进行吸附时,D3520树脂对豆腐柴果胶提取液具有良好的脱色效果;并对树脂再生的条件进行了较详细的研究.     

香菇多糖脱色工艺研究

研究了6种大孔吸附树脂和2种离子交换树脂对香菇多糖提取液中色素脱除的影响,在静态吸附试验研究的基础上,筛选出效果较好的树脂进行动态试验研究.研究发现,采用树脂DA201-C,在pH值4～6,温度40℃,流速3BV/h的工艺条件下,香菇多糖提取液中的色素脱除率达到87.8%,多糖保留率为85%,蛋白质的去除率为42%,树脂吸附后可先用1%NaOH和5%NaCl溶液浸泡,再用80%乙醇浸泡淋洗再生.     

蔗汁酒精废液色素的提取及其抗氧化活性研究

针对蔗汁酒精废液中含有的大量色素物,采用大孔树脂吸附提取色素,对蔗汁酒精废液中色素的提取工艺及其抗氧化活性进行了研究。通过静态吸附实验筛选出吸附树脂D101及对应的洗脱溶剂乙醇。最佳流速为3BV/h,最佳洗脱条件为40%的乙醇在pH6～7范围内进行洗脱。经测定,色素的黄酮含量为茶多酚的27.2%,但对自由基的抑制率却为茶多酚的88.06%,表明蔗汁酒精废液中提取的色素具有较高的抗氧化活性。     

活性艳红X-3B水溶液的光化学与光催化协同脱色反应

 对影响活性艳红X－3B水溶液光化学与光催化协同脱色反应的各种条件（如溶液的pH值,紫外光照强度,空气流量,催化剂用量及溶液的初始浓度等）进行了考察．结果表明,降解率随着紫外光照强度的增强而加快,随着X－3B初始浓度的增大而减慢;催化剂最佳用量为4g／L,空气最佳流量为4．3L／h．在X－3B水溶液的光催化脱色过程中,存在有光解反应,但它远不如光催化反应重要．因此,活性艳红X－3B水溶液的降解是光化学与光催化的协同脱色反应．     

优势菌固定化细胞对偶氮染料脱色的研究

利用紫外线诱变技术选育出高活力偶氮染料活性艳红X-3B脱色菌UVM7-9，以海藻酸钠为载体，采用包埋法固定UVM7-9细菌细胞用于处理含X-3B模拟废水。以固定化细胞对X-3B的脱色率和脱色寿命为试验指标，确定了最佳脱色条件，并与游离细胞对X-3B的脱色效果进行比较。结果表明，固定化细胞适应环境条件的范围更宽，脱色能力强，在30-35℃环境温度条件下，控制溶液pH为8，24h内对浓度为50mg／L的X-3B模拟废水的脱色率达93．8％。     

Reductive decolorization of a textile reactive dyebath under methanogenic conditions

The objective of the present study was to assess the biological decolorization of an industrial, spent reactive dyebath and its three dye components (Reactive Blue 19 [RB 19], Reactive Blue 21 [RB 21], and Reactive Red 198 [RR 198]) under methanogenic conditions. Using a mixed, methanogenic culture, batch assays were performed to evaluate the rate and exten of color removal as well as any potential toxic effects. Overall, a high rate and extent of color removal (>10 mg/[L·h] and 88%, respectively) were observed in cultures amended with either RB19 (an anthraquinone dye) or spent dyebath at an initial dye concentration of 300 mg/L (expressed as RB 19 equivalent) and 30 g/L of NaCl. Inhibition of acidogenesis and, to a larger degree, of methanogenesis resulting in accumulation of volatile fatty acids was observed in both RB 19- and spent dyebath-amended cultures. RB 21 (a phthalocyanine dye) and RR 198 (an azo dye) tested at an initial concentration of 300 mg/L did not result in any significant inhibition of the mixed methanogenic culture. Based on results obtained with cultures amended with RB 19 with and without NaCl, as well as a control culture amended with 30 g/L of NaCl, salt was less inhibitory than either RB 19 or the dyebath. Therefore, the toxic effect of the spent dyebath is at least partially attributed to its major dye component RB 19 and NaCl. Further testing of the effect of RB 19 decolorization products on the methanogenic activity in the absence of NaCl demonstrated that these products are much less inhibitory than the parent dye. Although color removal occurred despite the severe culture inhibition, biological decolorization of full-strength reactive spent dyebaths using methanogenic cultures in a repetitive, closed-loop system is not deemed feasible. For this reason, a fermentative and halotolerant culture was developed and successfully used in our laboratory for the decolorization of industrial reactive dyebaths with 100 g/L of NaCl.     

红花黄色素抗氧化活性研究

通过考察红花黄色素(SY)及其主要化学成分对羟基自由基介导2-脱氧核糖氧化降解的抑制作用,以及对1,1-二苯基-2-苦肼基自由基(DPPH·)的清除能力,探究SY的体外抗氧化活性及其抗氧化的主要有效成分.通过Fenton反应产生羟基自由基,用紫外分光光度计检测了SY及其主要化学成分对2-脱氧核糖降解的抑制作用和对DPPH·的清除能力,同时对红花黄色素B(SYB)抑制2-脱氧核糖降解的作用机制做了初步研究.结果表明SY抑制Fenton反应对2-脱氧核糖的氧化降解的IC50为256.79 μg/mL,对DPPH·清除的IC50值为27.15μg/mL.羟基红花黄色素A(HSYA)和SYB是SY中抗氧化的两个有效成分,抑制2-脱氧核糖的氧化降解的IC50分别为220.68 μg/mL和207.01μg/mL;对DPPH·清除的IC50值分别为55.81 μg/mL和41.25μg/mL.SYB对2-脱氧核糖氧化降解的抑制作用机理研究表明,SYB除了对Fenton反应产生的羟基自由基具有直接清除作用外,又可通过与Fe2+离子的络合作用而阻断Fenton反应产生羟基自由基.由此可知SY具有明显的体外抗氧化活性,SYB和HSYA为其主要抗氧化活性成分.     

臭氧氧化优尼素红B-B染料废水及脱色动力学研究

研究了在鼓泡反应器中,臭氧氧化优尼素红B-B模拟染料废水在10~70℃范围内的脱色反应动力学.发现并解释了不同温度下出现的反应速率交叉现象,利用紫外可见分光光度法定量分析染料特征颜色(浓度)变化情况.结果表明,在不同温度下,表观脱色反应动力学都符合一级动力学规律,相关系数都达到了0.95以上.40℃下,反应速率常数为0.011 83 s~(-1),臭氧氧化脱色过程符合y=exp(0.521-0.014x+5.02×10~(-6)x~2)方程.随着温度的升高,臭氧在高温下氧化染料的反应速率小于臭氧的分解速率,低温时臭氧氧化的速率高于臭氧的分解速率,导致高温下氧化速率变慢.在40~50℃时,臭氧氧化优尼素红B-B染料废水脱色率最高,利用紫外可见分光光度法对氧化后废水进行分析,结果表明脱色率达到了99.5%.     

Substituent effects on thermal decolorization rates of bisbenzospiropyrans

[reaction: see text] A novel application of photochromic molecules is to mimic physiological oscillatory calcium signals by reversibly binding and releasing calcium ions in response to light. Substituent changes on the largely unexplored photochromic bisbenzospiropyran scaffold led to significant changes in thermal fading rates in several organic solvents. Excellent correlations have been found between fading rates and empirical Hammett constants as well as calculated ground-state energies. These correlations can be used to improve scaffold design.     

Cuprous oxide/titanium dioxide composite photocatalytic decolorization of reactive brilliant red X-3B dyes wastewater under visible light

Research on Chemical Intermediates - In recent years, how to improve photocatalytic performance under visible light has become one of the research hot topics. The nano-TiO2 particles were...     

活性炭对乙二醛溶液的脱色研究

乙二醛是一种重要的化工产品和医药中间体,在纺织印染、建材、皮革、医药、农药、国防、涂料、轻工、粘合剂、石油、冶金、环保等方面具有广泛的用途[1,2]。其工业生产方法主要有乙醛硝酸氧化法和乙醇气相氧化法[3~6]。两种方法制得的乙二醛溶液在纯化过程中,溶液颜色加深,不能     

Study of reactive ion etching of Si and SiO2 for CFxCl4−x gases

A parametric study of the etching of Si and SiO₂ by reactive ion etching (RIE) was carried out to gain a better understanding of the etching mechanisms. The following fluorocarbons (FCs) were used in order to study the effect of the F-to-Cl atom ratio in the parent molecule to the plasma and the etching properties: CF₄, CF₃Cl, CF₂Cl₂, and CFCl₃ (FC-14, FC-13, FC-12, and FC-11 respectively). The Si etch rate uniformity across the wafer as a function of the temperature of the wafer and the Si load, the optical emission as a function of the temperature of the load, the etch rate of SiO₂ as a function of the sheath voltage, and the mass spectra for each of the FCs were measured. The temperature of the wafer and that of the surrounding Si load strongly influence the etch rate of Si, the uniformity of etching, and the optical emission of F, Cl, and CF₂. The activation energy for the etching reaction of Si during CF₄ RIE was measured. The etch rate of Si depends more strongly on the gas composition than on the sheath voltage; it seems to be dominated by ion-assisted chemical etching. The etching of photoresist shifted from chemical etching to ion-assisted chemical etching as a function of the F-to-Cl ratio and the sheath voltage. The etch rate of SiO₂ depended more strongly on the sheath voltage than on the F-to-Cl ratio.     

Vibrational assignment of the 4-hydroxycinnamyl chromophore in photoactive yellow protein

Photoactive yellow protein (PYP) is a bacterial photoreceptor containing a 4-hydroxycinnamyl chromophore. We report the Raman spectra for the dark state of PYP whose chromophore is isotopically labeled with 13C at the carbonyl carbon atom or at the ring carbon atoms. Spectra have been also measured with PYP in D2O where the exchangeable protons are deuterated. Most of the observed Raman bands are assigned on the basis of the observed isotope shifts and normal mode calculations using a density functional theory. We discuss the implication for the analysis of the infrared spectra of PYP. The comprehensive assignment provides a satisfactory framework for future investigations of the photocycle mechanism in PYP by vibrational spectroscopy.     

Adsorption characteristics of Titan yellow and Congo red on CoFe2O4 magnetic nanoparticles

This paper assesses the adsorption characteristics of Titan yellow and Congo red on CoFe₂O₄ magnetic nanoparticles. The adsorption behavior of Titan yellow and Congo red from aqueous solution onto CoFe₂O₄ magnetic nanoparticles has been determined by investigating the effects of pH, concentration of the dye, amount of adsorbent, contact time, ionic strength and temperature. Experimental results indicated that CoFe₂O₄ nanoparticles can remove more than 98 % of each dye under optimum operational conditions of a dosage of 15.0 mg CoFe₂O₄, pH 3.0, initial dye concentration of 22–140 mg L^?1, and contact times of 2.0 and 15.0 min for Congo red and Titan yellow, respectively. Langmuir and Freundlich isotherm models have been used to evaluate the ongoing adsorption kinetic equations. Regeneration of the saturated adsorbent was possible by NaCl/acetone solution as eluent. The maximum adsorption capacities were 200.0 and 212.8 mg dye per gram adsorbent for Congo red and Titan yellow, respectively. With the help of adsorption isotherm, thermodynamic parameters such as free energy, enthalpy and entropy have been calculated. On the basis of pseudo-first-order and pseudo-second-order kinetic equations, different kinetic parameters have been obtained.