4-二氰亚甲基-2,6-二甲基-4H-吡喃衍生物的合成及其 荧光效应

两种新的4-二氰亚甲基-2,6-二甲基-4H-吡喃衍生物及对应的聚酰胺酸被合成和表征。该聚酰胺酸在普通有机溶剂中具有良好的可溶性。报道了这些生色团衍生物的光强度、量子产率和发射波长,以及生色团共价键合所形成的聚酰胺酸膜具有比对应的生色团单体更强的荧光效应。     

以β-二酮连接的含生色团丙烯酰类单体及其饱和模型化合物的荧光行为

通过合成一系列同一分子中既含有给电子性荧光生色团又含缺电子性碳碳双键的烯类单体, 发现这类单体在相同生色团浓度下的荧光强度均明显低于相应的饱和模型化合物或聚合物[1～3]. 这种现象称为荧光结构自猝灭效应(SSQE), 以区别于浓度自猝灭现象. 对于电子状态与之相反的单体, 即含受电子性荧光生色团的乙烯基醚类单体, 也观察到了SSQE[4,5]. 进一步的研究结果表明, SSQE是光照条件下分子内电子给受体之间电荷转移作用的结果, 分子中电子给受体间的间隔基长度和溶剂的性质等都对SSQE有显著的影响[6]. 以往合成的含给生色团的丙烯酰类单体, 其电子给受体间是通过饱和脂肪链相连, 当生色团和受电子性碳碳双键之间以β-二酮结构相连时, 这类单体的荧光性质如何, 是否发生SSQE是我们的关注所在. 另一方面, β-二酮类化合物在一定波长光照射条件下, 常发生烯醇式与酮式的互变异构化. 虽然已有许多文献报道有关烯醇式-酮式互变异构过程中各种光谱的变化以及用核磁、红外、紫外等光谱手段研究烯醇式-酮式互变异构动力学, 但有关β-二酮类化合物互变异构过程中荧光光谱的变化的报道却很少[7～11]. 本文合成了以β-二酮连接的含二甲氨基苯基生色团的烯类单体, 1-(4-二甲氨基苯基)-4-甲基-4-戊烯-1,3-二酮(DMPDK)及其饱和模型化合物1-(4-二甲氨基苯基)-1,3-丁二酮(DMBDK), 研究了其光谱性质及光致互变异构行为.     

新型二阶非线性光学生色团的合成及辅助给体对分子性能的影响研究

为了研究辅助给体对生色团分子热分解温度以及二阶极化率的影响,以已报道生色团分子2-二氰亚甲基-3-氰基-4-(4-二乙胺基-苯乙烯基)-5,5-二甲基-2,5-二氢呋喃(DCDHF-2-V)为基础,分别在苯环二乙胺基的邻位上以羟基、丁氧基和苄氧基作为辅助给体合成了三种新型的生色团分子:EFC-OH,EFC-OBu和EFC-OBe.通过核磁共振、红外光谱以及元素分析表征确认了其结构.热失重分析结果表明,三种分子的热性能良好,其中EFC-OBe的热分解温度(Td)最高为278.6℃.溶致变色法测定结果表明,EFC-OBe的二阶非线性光学系数(μgβ1064 nm)最高,为47149×10-48 esu.将这三种分子的Td值和μgβ值与未加入辅助给体的DCDHF-2-V分子进行对比,结果表明辅助给体的加入对分子的热稳定性能影响不大,但能显著提高分子的μgβ值一个数量级以上.     

含对硝基偶氮苯胺生色团的键合型有机/无机复合材料的合成及其二阶非线性光学特性

以γ 缩水甘油氧丙基三甲氧基硅烷 (KH5 6 0 )作中间体 ,用溶胶 凝胶 (Sol Gel)法合成了含对硝基偶氮苯胺 (DO3)生色团的新型键合型有机 /无机复合非线性光学 (NLO)材料 ,在这种有机生色团与无机玻璃键合形成的交联网络结构中 ,无机玻璃的刚性三维结构和优良的高温稳定性能有效抑制NLO生色团的极化松弛 .二次谐波信号 (SHG)测量表明 ,合成的键合型聚合物膜的二阶非线性光学系数 (d33)值达 5 79× 10 -7esu ,NLO稳定性也较好 ;在室温下放置 90天后 ,其d33 值能维持初始值的 93 5 % ;在 10 0℃下放置 30 0min后 ,其d33 值仍能维持初始值的 6 0 %     

含双呋喃共轭桥的有机非线性生色团的合成及性能

通过Wittig反应和Vilsmeier反应合成了一种以双呋喃为共轭桥, 2,2,3-三甲基-4-氰基-5-二氰基亚甲基-2,5-二氢呋喃(TCF)为受体, 并以二甲胺基为给体的有机非线性生色团分子MF₃C, 利用红外光谱、 ¹H NMR和元素分析对其结构进行了表征. 热重分析结果表明, 该分子的热分解温度达228℃; 利用溶致变色法对该生色团分子的二阶非线性品质参数μ_gβ进行了计算, 在1064 nm波长下MF₃C的μ_gβ值达到5.9×10^-44 esu. 可见, 该生色团兼具较好的热稳定性和较大的超极化率.     

外围带咔唑基的联苯桥联二聚对苯乙烯撑的双光子吸收性能

报道了十字形结构对荧光生色团的双光子吸收(TPA)作用横截面积的影响. 1,4-二(9'-乙基咔唑基)- 3'-乙烯基苯(R1)是经典的具有D-π-D结构的TPA生色团. 通过一个联苯桥将两个双光吸引(TPA)链连接在一起得到的十字形分子(1)显示出比单链分子明显增大的双光子吸收作用横截面积(σ'). 在10-4 mol/L 的甲苯溶液中, 十字结构分子1的σ'值为491.0×10-50 cm4·s, 而R1的σ'值仅为137.5×10-50 cm4·s. σ'的放大可以归结为十字结构使TPA 生色团的偶极呈交叉排列, 抑制了浓溶液中的荧光猝灭.     

So1-Gel法制备键合型有机/无机复合非线性光学材料

以含对硝基苯胺生色团的烷氧基硅烷染料和正硅酸乙酯为原料,通过溶胶-凝胶法合成了含对硝基苯胺生色团的键合型有机/无机复合非线性光学材料.在这种有机生色团与无机玻璃键合形成的交联网络中,无机玻璃的刚性三维结构和优良的高温稳定性能有效抑制非线性光学生色团的极化松弛.二阶谐波信号(SHG)测量表明,这种有机/无机复合材料的二阶非线性光学系数(d33)值达到4.62 × 10-8esu;NLO稳定性也较好;室温下90d后d33值维持初始值的84.5%,100℃下放置300min后d33值维持初始值的51%.     

利用聚合物自组装实现绿色荧光蛋白生色团的荧光增强

根据绿色荧光蛋白的发光原理,采用聚乙二醇与聚甲基丙烯酸甲酯的两亲性两嵌段聚合物通过自组装包覆生色团的方式,模拟了绿色荧光蛋白发光,考察了组装行为对光学性能的影响,并将其用于细胞成像.通过核磁共振、高分辨质谱、傅里叶变换红外光谱、凝胶渗透色谱、紫外-可见吸收光谱及荧光光谱等表征了生色团分子和聚合物的结构及性能.生色团紫外最大吸收在371 nm,荧光最大发射峰在428 nm.聚合物和生色团进行组装后,其紫外吸收消失,而最大荧光发射峰强度大大增强,且发生了约70 nm的红移,这是因为组装使得生色团的自由旋转受到了限制,且生色团共平面性增加.动态光散射(DLS)和透射电镜(TEM)证明了纳米粒子的结构和尺寸.由于尺寸适合且具有较好的荧光性能,纳米粒子成功应用于细胞成像.这种绿色荧光蛋白生色团的简单自组装方式在生物成像领域具有良好应用前景.     

含呋喃共轭桥有机非线性光学生色团的合成及性能研究

通过两次羟醛缩合反应合成了一种含呋喃共轭桥的有机非线性光学生色团分子2-二氰亚甲基-3-氰基-4-[2-(4-二乙氨基-苯乙烯基-呋喃基-5)-乙烯基]-5,5-二甲基-2,5-二氢呋喃(EFFC), 用IR谱、¹H NMR谱以及元素分析表征确认了其结构. 热失重分析表明, 材料的热分解温度T_d为250℃. 用密度泛函理论的B3LYP方法在6-31G基组下对这种生色团分子进行了结构优化, 并在相同基组下对分子的静态二阶极化率进行了计算, 分子的b₀=6.5×10^-28 esu. 将分子以18%的质量比与聚砜进行主-客体掺杂, 用溶胶凝胶法制备成膜后进行极化, 用二次谐波法对掺杂极化聚合物薄膜的电光系数进行测量, 其r₃₃值最高达到80 pm/V.     

聚合物重氮偶合反应制备二阶非线性光学聚酰亚胺

在合成一种新的二胺单体[2-(N-乙基苯胺基)-乙氧基对苯二胺]基础上,与6FDA(4,4′-(六氟异丙基)-双邻苯二甲酸酐)反应制备了聚酰亚胺先驱聚合物,利用聚合物的后重氮偶合反应将硝基偶氮苯生色团引入到聚合物当中.此方法避免了亚胺化苛刻条件对生色团的影响,在温和条件下能达到高的官能化度.对侧链型偶氮聚酰亚胺材料的二阶非线性光学性能进行了测试,其d33可达39.2 pm/V.     

Synthesis and second-order nonlinear optical properties of a crosslinkable functionalized hyperbranched polymer

A new implementation of copper-free thermal Huisgen 1,3-dipolar crosslinking reaction into a high T_g hyperbranched polyimide polymer in order to stabilize the electro-optic (EO) activity of second-order non linear materials is reported. Towards this goal, two different synthetic approaches were explored. The first strategy is based on the post-functionalization of the polymer with mixtures of DR1 azido derivative and propargylic alcohol, whereas, the second consists in the preparation of two complementary functionalized hyperbranched polymers that are mixed just before the preparation of films. Materials exhibit good second-order nonlinear optical coefficients (d₃₃) close to 30 pm/V at the fundamental wavelength of 1064 nm. Moreover, the thermal stability of the NLO properties of these materials reaches temperatures as high as 150 °C, and probably higher. This represents the highest thermal stability of crosslinkable EO polymers based on the crosslinking Huisgen reaction.     

可交联的PMMA型和PS型高热稳定性二阶非线性光学材料的合成与表征

采用封管反应的方法,以较高产率(80%以上)合成了一系列含环氧基团的可交联PMMA型和PS型极化聚合物材料,该材料具有很好的成膜性.用DSC和T_gA等方法研究了聚合物固化前后的热性能,结果表明,由于聚合物在极化后期经热固化使引入的环氧基团开环交联,聚合物的玻璃化转变温度(T_g)较固化前明显提高30～50K.同时,固化后的聚合物具有较高的热分解温度(T_d>543K).对聚合物的二阶非线性光学性质的测试结果表明,在室温下放置100h后,聚合物的电光系数r₃₃值均保持在初始值的75%以上.这是由于环氧基团的开环使固化后的聚合物本身产生一定程度的交联,导致取向后的发色团被聚合物的交联网禁锢而不易弛豫,从而使这类PMMA型和PS型二阶非线性聚合物材料的热稳定性能得以提高.     

Viscoelastic and thermal characterization of crosslinked PVC

Soft PVC is employed for the manufacturing of a wide range of products with different properties and a relatively low cost. The utilization of soft PVC is restricted by the poor thermal, chemical and mechanical resistance properties. Also, plasticizer migration can modify the properties or can make useless the materials for some applications because of toxicity or a general loss of properties. PVC crosslinking is the most effective way to improve mechanical and transport properties of rigid or flexible PVC at high temperatures, but at the same time the thermal stability of PVC may be significantly reduced. In this work, the crosslinking reaction of plasticized poly(vinyl chloride) (PVC) through difunctional amines was studied. The mechanisms involved in the crosslinking reaction were explained by Fourier transform infrared (FTIR) analysis. The thermal activated crosslinking reaction was studied by cone and plate rheometry, analyzing the evolution of viscoelastic properties of the suspension as a function of time and temperature. The effect of the addition of crosslinking agents on the thermal stability of the polymer was studied by thermogravimetric analysis (TGA), which revealed that crosslinking reactions promote thermal degradation phenomena in the polymer matrix. This is attributed to the formation of HCl and other species promoting polymer degradation during crosslinking, thus leading to higher weight loss during thermal treatment with respect to unmodified PVC plastisols. This was also confirmed by an evident yellowing after crosslinking, especially at higher temperatures.     

高热稳定性和可逆交联性质的含新型偶氮发色团电光聚合物的研究

制备了两种新型的分别含有以三苯胺为电子给体的偶氮类发色团作为特征活性官能团和3-呋喃甲酸及受保护的马来酰亚胺的可交联型聚合物体系.通过研究表明利用该制备方法,发色团在聚合物中的含量得到了极大的提高,分别达到32 .1 %( NLO1-P1)和44 .4 %( NLO1-P2) .该聚合物体系以"Diels-Alder"[4 +2]环加成反应作为其交联特征,具有高温非交联、低温交联的特点,其过程与以往的热交联型聚合物相反,可解决传统电光交联聚合物中存在的热交联对极化效率影响的问题并用热失重分析法(TGA)和差示扫描量热法(DSC)分析了这一过程.此外DA交联型聚合物,不需要引入额外的助交联剂,克服了传统热交联聚合物分离难的问题,最大程度的保证了材料的纯度.     

一种新型二阶非线性光学功能分子及其交联聚氨酯材料的合成

合成了新型的含有偶氮和噻吩环的二阶非线性光学功能分子, 用红外光谱、紫外光谱、核磁共振和质谱确定了其结构; 制备了含有该功能分子的两种交联型聚氨酯聚合物薄膜, 当测量波长为1 064 nm时,  用Marker条纹法测得的二阶非线性光学系数d33值分别为80.6 pm/V(发色团的数密度为0.91×1020 Molecules/cm3)和20.1 pm/V(发色团的数密度为2.21×1020 Molecules/cm3); 聚合物Ⅱ的取向热稳定性达到了152 ℃.     

非线性光学环氧聚合物的近程结构对二次谐波产生弛豫特性的影响

设计合成了三种具有不同主链化学结构的二阶非线性光学功能化环氧聚合物,并对其化学结构进行了表征,考察了聚合物近程结构对材料极化后二次谐波产生弛豫特性的影响。极化后线型聚合物链节的扭转弹性回复是二次谐波产生弛豫的主要原因,在温度处于Ｔｇ 以下或Ｔｇ 附近时玻璃化转变温度的高低决定了二次谐波产生弛豫的快慢;聚合物交联后有助于提高二次谐波产生的稳定性,但此时聚合物单个链节结构的柔顺性成为影响二次谐波产生弛豫的主要原因,刚性越大,材料将具有更稳定的二次谐波产生性能。极化聚合物的二次谐波产生弛豫过程非常复杂,需要综合考虑聚合物材料的近程和远程结构因素。     

Network formation of a phenyl vinyl ketone copolymer with 4-vinylbenzil and its photodecrosslinking in films

The irradiation (λ > 400 nm) in air of a copolymer of phenyl vinyl ketone with 4-vinylbenzil (VBZ) containing 1.5 wt % VBZ structural units in film, followed by the thermal decomposition of the resulting pendant benzoyl peroxide groups, leads to crosslinking. The subsequent irradiation of the crosslinked polymer at 366 nm results in the cleavage of the poly(phenyl vinyl ketone) chain between the junction points of the polymer network through a Norrish type II reaction. Therefore, poly(phenyl vinyl ketone-co-4-vinylbenzil) represents a novel type of photoresist based on polymer network decrosslinking. The process involves three steps: photogeneration of peroxide, crosslinking by its thermal decomposition, and subsequent photodecrosslinking of the polymer network. This material provides positive-tone images after UV exposure (λ > 330 nm) and development in an organic medium such as isopropyl methyl ketone. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 765–771, 2004     

Photovoltaic properties of the polymer solar cells comprising crosslinked maleimide polymers and fullerene‐derivative PCBM

A series of crosslinkable maleimide conjugated polymers with different vinyl group contents as side‐chain crosslinking sites have been synthesized by the Suzuki coupling reaction. Polymer solar cells (PSCs) were fabricated based on an interpenetrating network of the crosslinkable maleimide polymers as the electron donor, and a fullerene derivative, (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM), as the electron acceptor. The crosslinkable maleimide polymers underwent crosslinking reaction at the side‐chain vinyl groups upon the thermal treatment with or without the addition of initiator, azobisisobutyronitrile (AIBN). Better photovoltaic (PV) performances were obtained for the PSCs based on the polymer crosslinking without using initiator, whereas poorer PV performances were observed for the PSCs based on the polymer crosslinking with the AIBN initiator. In addition, higher operational stability was observed for the crosslinked polymer based solar cell as compared to the solar cell based on the un‐crosslinked polymer. The photo‐physical and PV properties of the cross‐linked maleimide polymers/PCBM based PSCs are discussed in detail as the morphology and crosslinking density of the polymers are taken into account. Copyright © 2010 John Wiley & Sons, Ltd.     

A novel metal-organic network with high thermal stability: nonlinear optical and photoluminescent properties

A novel zinc(II) 4-(5H-tetrazol)benzoic coordination polymer with an in situ generated tetrazole ligand exhibits the gsi (gamma-silicon) topology and high thermal stability; this compound possesses second-order nonlinear optical and interesting heat-induced photoluminescent properties.