In-hole and mainflow velocity measurements of low-momentum jets in crossflow emanating from short holes

Discrete hole film cooling utilizes jet-in-crossflow geometry where the jet is supplied through a short hole which may be pitched relative to the main flow. Typically, the velocity ratio is near one. Under these conditions, the mean flow structure of the jet/mainstream interaction may be strongly affected by the characteristics of the flow within the hole. Magnetic resonance velocimetry (MRV) is used to measure the 3-dimensional mean velocity field for various jets in crossflow with short holes of varied inclination angles and blowing ratios typically of gas turbine applications. Novel measurements of the flow within inclined feed holes are captured using MRV. Secondary flows within the hole are found to be strongly dependent on the inclination of the hole. The traditional counter-rotating vortex pair is observed in the mainstream, as well as high levels of wall-normal vorticity. The 3D vorticity field is used to modify traditional jet-in-crossflow vortex ring theory to apply to low-momentum jets which remain attached to the ejection surface.     

On the Evolution of the Flow Field in a Spark Ignition Engine

The development of the turbulent flow field inside a spark ignition engine is examined by large-eddy simulation (LES), from the intake flow to the tumble break-down. Ten consecutive cold flow engine cycles on a coarse and twenty cycles on a fine grid are simulated and compared to experiments of the same engine. The turbulent subgrid scales are modeled by the standard Smagorinsky and by the recently developed Sigma model. A comparison of the intake flow is made against Particle Image Velocimetry (PIV) measurements along horizontal and vertical lines and to an LES simulation performed by the Darmstadt group. Furthermore, we show the first LES comparison to Magnetic Resonance Velocimetry (MRV conducted by Freudenhammer et al.) measurements, which provided the 3D flow field inside a full scale dummy of the entire upper cylinder head including the valve seat region, at a time which mimics inflow conditions of the corresponding engine. Our LES is in good qualitative and quantitative agreement with the simulation and the experiments, with the notable exception of the measured in-cylinder pressure, which is discussed in detail and compared to 0D simulations and simulations from other groups. A criterion is proposed for estimating the number of cycles needed in a simulation, if experimental data is available. We put emphasis on the flow in the valve seat region, where turbulence is generated, and discuss the formation of the large scale tumble motion, including a comparison of the radial velocity fields on rolled-up planes around the valve seat. Here, spots of high velocities were found in the under flow region, which cannot been seen by the ensemble averaged MRV measurement. Within the compression stroke, a 2D vortex center identification algorithm is applied on slices inside the combustion chamber, yielding a 3D visualization of the tumble vortex, which is found to have a “croissant-like” shape. The tumble vortex trajectory is plotted on the symmetry plane and compared to measurements. Finally, we consider a modified definition of the (turbulent) integral length scale that provided further insight to the tumble break-down process.     

Numerical modelling of film cooling from converging slot-hole

This paper presents a numerical prediction of a new 3D film cooling hole geometry, the converging slot-hole or console. The console geometry is designed in order to improve the heat transfer and aerodynamic loss performance of turbine vane and rotor blade cooling systems without loosing the mechanical strength of a row of discrete holes. The cross section of the console changes from a circular shape at the inlet to a slot at the exit. Previous successful application of a new anisotropic DNS based two-layer turbulence model to cylindrical and shaped hole injections is extended to predict film cooling for the new console geometry. The suitability of the proposed turbulence model for film cooling flow is validated by comparing the computed and the measured wall-temperature distributions of cylindrical hole injections. The result shows that the anisotropic eddy-viscosity/diffusivity model can correctly predict the spanwise spreading of the temperature field and reduce the strength of the secondary vortices. Comparative computations of the adiabatic film cooling effectiveness associated with the three geometries tested in the present study (cylindrical, shaped, and console) show that the new console film-cooling hole geometry is definitely superior to the other geometries as shown by the uniform lateral spreading of the effectiveness with a slight enhancement downstream of the intersection of the two consoles.     

Passive Scalar Transport in a Turbulent Mixing Layer

This paper describes a combined experimental and numerical study of scalar transport in spatially developing, two-stream, turbulent mixing layers with velocity ratios of approximately 2:1. The experimental mixing layer was created by an S-shaped splitter plate mounted in a wind tunnel, and the concentration field was realized by releasing incense smoke into the high-speed side boundary layer above the splitter plate. Simultaneous measurements of the velocity and concentration fields were performed. A 12-sensor hot-wire probe was used to measure the velocity field and its gradients, while the concentration field was recorded with digital photographs of the laser-illuminated smoke. In parallel, a large-eddy simulation (LES) of the spatially developing mixing layer was carried out. Auxiliary turbulent boundary layer LES were used to provide high quality inflow boundary conditions for the velocity and concentration fields. By synchronizing the velocity and concentration measurements, concentration fluxes were also determined. Octant analysis based on the sign combinations of the velocity and concentration fuctuations was performed on the flux data to investigate the scalar transport processes. It was found that octants compatible with mean gradient transport of the scalar contribute most to the scalar fluxes. Conditional planar averages of scalar and momentum fluxes were obtained to determine their spatial distribution with respect to the organized roller and rib vortices of the mixing layer, and distinct patterns were observed. The simulation provided additional insight about the flow and scalar flux distribution topology. This topology was found to be partially compatible with simple models of roller and rib vortices that transport the scalar in a mean gradient sense.     

Experimentally informed optimization of turbulent diffusivity for a discrete hole film cooling geometry

A process has been developed by which mean velocity and concentration measurements can be used to determine optimal turbulent diffusivity values for an angled jet in cross-flow configuration. This configuration has applications in film cooling for gas turbine blades. The measurements, obtained by magnetic resonance imaging techniques, provide 3D time-averaged velocity and concentration fields. The mean velocity field is fed into a Reynolds-Averaged Advection Diffusion solver, which uses a turbulent diffusivity model to solve for the mean coolant concentration distribution. This distribution can be compared to the experimentally-obtained concentration field by means of an error metric that quantifies the difference between the computational and experimental concentration fields. By minimizing this error, an optimal value of the turbulent diffusivity can be determined. This optimized distribution is then compared to a RANS simulation to evaluate the relative contribution to error of the turbulent momentum flux model versus the turbulent scalar flux model.     

Fluid flow investigations within a 37 element CANDU fuel bundle supported by magnetic resonance velocimetry and computational fluid dynamics

The current work presents experimental and computational investigations of fluid flow through a 37 element CANDU nuclear fuel bundle. Experiments based on Magnetic Resonance Velocimetry (MRV) permit three-dimensional, three-component fluid velocity measurements to be made within the bundle with sub-millimeter resolution that are non-intrusive, do not require tracer particles or optical access of the flow field. Computational fluid dynamic (CFD) simulations of the foregoing experiments were performed with the hydra-th code using implicit large eddy simulation, which were in good agreement with experimental measurements of the fluid velocity. Greater understanding has been gained in the evolution of geometry-induced inter-subchannel mixing, the local effects of obstructed debris on the local flow field, and various turbulent effects, such as recirculation, swirl and separation. These capabilities are not available with conventional experimental techniques or thermal-hydraulic codes. The overall goal of this work is to continue developing experimental and computational capabilities for further investigations that reliably support nuclear reactor performance and safety.     

Turbulent Scalar Mixing in a Skewed Jet in Crossflow: Experiments and Modeling

Turbulent mixing of an inclined, skewed jet injected into a crossflow is investigated using MRI-based experiments and a high-fidelity LES of the same configuration. The MRI technique provides three-dimensional fields of mean velocity and mean jet concentration. The 30° skew of the jet relative to the crossflow produces a single dominant vortex which introduces spanwise asymmetries to the velocity and concentration fields. The turbulent scalar transport of the skewed jet is investigated in further detail using the LES, which is validated against the experimental measurements. Mixing is found to be highly anisotropic throughout the jet region. Isotropic turbulent diffusivity and viscosity are used to calculate an optimal value of the turbulent Schmidt number, which varies widely over the jet region and lies mostly outside of the typically accepted range 0.7 ≤ S c _t ≤ 0.9. Finally, three common scalar flux models of increasing complexity are evaluated based on their ability to capture the anisotropy and predict the scalar concentration field of the present configuration. The higher order models are shown to better represent the turbulent scalar flux vector, leading to more accurate calculations of the concentration field. While more complex models are better able to capture the turbulent mixing, optimization of model constants is shown to significantly affect the results.     

高超声速溢流冷却实验研究

高超声速溢流冷却是一种新型的飞行器热防护方法,基本思想为:在高热流区布置溢流孔,控制冷却液以溢流方式流出,之后通过飞行器表面摩阻作用展布为液膜,形成热缓冲层以降低飞行器表面热流. 目前,溢流冷却技术还处于探索阶段,实现工程应用前还需开展大量的实验验证和机理研究工作. 本文首次开展溢流冷却的实验研究工作,采用热流测量、液膜厚度测量及液膜流动特性观测技术,搭建了完善的溢流冷却风洞实验平台,对溢流冷却热防护性能和高超声速条件下液膜流动规律进行了初步研究. 研究表明:(1) 高超声速流场中通过溢流能够在飞行器表面形成液膜并有效隔离外部高温气流,可降低飞行器表面热流率;(2) 楔面上的液膜前缘流动是一个逐渐减速的过程,增加冷却液流量液膜厚度变化不明显,但液膜前缘运动速度增大;(3) 液膜层存在表面波,在时间和空间方向发生演化,导致液膜厚度的微弱扰动;(4) 液膜层存在横向展宽现象,即液膜层宽度大于溢流缝宽度. 原因是液膜层与流场边界层条件不匹配,存在压力梯度,迫使冷却液向低压区流动,从而展宽液膜层,并且流量越高,横向展宽现象越明显.      

Large Eddy Simulation of Scalar Mixing in a Coaxial Confined Jet

The highly turbulent flow occurring inside gas-turbine combustors requires accurate simulation of scalar mixing if CFD methods are to be used with confidence in design. This has motivated the present paper, which describes the implementation of a passive scalar transport equation into an LES code, including assessment/testing of alternative discretisation schemes to avoid over/undershoots and excessive smoothing. Both second order accurate TVD and higher order accurate DRP schemes are assessed. The best performance is displayed by a DRP method, but this is only true on fine meshes; it produces similar (or larger) errors to a TVD scheme on coarser meshes, and the TVD approach has been retained for LES applications. The unsteady scalar mixing performance of the LES code is validated against published DNS data for a slightly heated channel flow. Excellent agreement between the current LES predictions and DNS data is obtained, for both velocity and scalar statistics. Finally, the developed methodology is applied to scalar transport in a confined co-axial jet mixing flow, for which experimental data are available. Agreement with statistically averaged fields for both velocity and scalar, is demonstrated to be very good, and a considerable improvement over the standard eddy viscosity RANS approach. Illustrations are presented of predicted time-resolved information e.g. time histories, and scalar pdf predictions. The LES results are shown, even using a simple Smagorinsky SGS model, to predict (correctly) lower values of the turbulent Prandtl number in the free shear regions of the flow, compared to higher values in the wall-affected regions. The ability to predict turbulent Prandtl number variations (rather than input these as in combustor RANS CFD models) is an important and promising feature of the LES approach for combustor flow simulation since it is known to be important in determining combustor exit temperature traverse.     

Turbulent transport in an inclined jet in crossflow

The present study experimentally investigates a turbulent jet in crossflow relevant to film cooling applications. The jet is inclined at 30°, and its mean velocity is the same as the crossflow. Magnetic resonance imaging is used to obtain the full three-dimensional velocity and concentration fields, whereas Reynolds stresses are obtained along selected planes by Particle Image Velocimetry. The critical role of the counter-rotating vortex pair in the mixing process is apparent from both velocity and concentration fields. The jet entrainment is not significantly higher than in an axisymmetric jet without crossflow, because the proximity of the wall inhibits the turbulent transport. Reynolds shear stresses correlate with velocity and concentration gradients, consistent with the fundamental assumptions of simple turbulence models. However the eddy viscosity is strongly anisotropic and non-homogeneous, being especially low along the leeward side of the jet close to injection. Turbulent diffusion acts to decouple mean velocity and concentration fields, as demonstrated by the drop in concentration flux within the streamtube issued from the hole. Volume-averaged turbulent diffusivity is calculated using a mass–flux balance across the streamtube emanating from the jet hole, and it is found to vary slowly in the streamwise direction. The data are compared with Reynolds-Averaged Navier–Stokes simulations with standard k − ε closure and an optimal turbulent Schmidt number. The computations underestimate the strength of the counter-rotating vortex pair, due to an overestimated eddy viscosity. On the other hand the entrainment is increasingly underpredicted downstream of injection. To capture the correct macroscopic trends, eddy viscosity and eddy diffusivity should vary spatially in different ways. Therefore a constant turbulent Schmidt number formulation is inadequate for this flow.     

DNS,LES and RANS of turbulent heat transfer in boundary layer with suddenly changing wall thermal conditions

The objectives of this study are to investigate a thermal field in a turbulent boundary layer with suddenly changing wall thermal conditions by means of direct numerical simulation (DNS), and to evaluate predictions of a turbulence model in such a thermal field, in which DNS of spatially developing boundary layers with heat transfer can be conducted using the generation of turbulent inflow data as a method. In this study, two types of wall thermal condition are investigated using DNS and predicted by large eddy simulation (LES) and Reynolds-averaged Navier–Stokes equation simulation (RANS). In the first case, the velocity boundary layer only develops in the entrance of simulation, and the flat plate is heated from the halfway point, i.e., the adiabatic wall condition is adopted in the entrance, and the entrance region of thermal field in turbulence is simulated. Then, the thermal boundary layer develops along a constant temperature wall followed by adiabatic wall. In the second case, velocity and thermal boundary layers simultaneously develop, and the wall thermal condition is changed from a constant temperature to an adiabatic wall in the downstream region. DNS results clearly show the statistics and structure of turbulent heat transfer in a constant temperature wall followed by an adiabatic wall. In the first case, the entrance region of thermal field in turbulence can be also observed. Thus, both the development and the entrance regions in thermal fields can be explored, and the effects upstream of the thermal field on the adiabatic region are investigated. On the other hand, evaluations of predictions by LES and RANS are conducted using DNS results. The predictions of both LES and RANS almost agree with the DNS results in both cases, but the predicted temperature variances near the wall by RANS give different results as compared with DNS. This is because the dissipation rate of temperature variance is difficult to predict by the present RANS, which is found by the evaluation using DNS results.     

Numerical Analysis of the Impact of the Interior Nozzle Geometry on Low Mach Number Jet Acoustics

The flow and acoustic fields of subsonic turbulent hot jets exhausting from three divergent nozzles at a Mach number M=0.12 based on the nozzle exit velocity are conducted using a hybrid CFD-CAA method. The flow field is computed by highly resolved large-eddy simulations (LES) and the acoustic field is computed by solving the acoustic perturbation equations (APE) whose acoustic source terms are determined by the LES. The LES of the computational domain includes the interior of the nozzle geometry. Synthetic turbulence is prescribed at the inlet of the nozzle to mimic the exit conditions downstream of the last turbine stage. The LES is based on hierarchically refined Cartesian meshes, where the nozzle wall boundaries are resolved by a conservative cut-cell method. The APE solution is determined on a block structured mesh. Three nozzle geometries of increasing complexity are considered, i.e., the flow and acoustic fields of a clean geometry without any built-in components, a nozzle with a centerbody, and a nozzle with a centerbody plus struts are computed. Spectral distributions of the LES based turbulent fluctuated quantities inside the nozzle and further downstream are analyzed in detail. The noise sources in the near field are noticeably influenced by the nozzle built-in components. The centerbody nozzle increases the overall sound pressure level (OASPL) in the near field with respect to the clean nozzle and the centerbody-plus-strut nozzle reduces it compared to the centerbody nozzle due to the increased turbulent mixing. The centerbody perturbed nozzle configurations generate a remarkable spectral peak at S t=0.56 which also occurs in the APE findings in the near field region. This tone is generated by large scale vortical structures shed from the centerbody. The analysis of the individual noise sources shows that the entropy term possesses the highest acoustic contribution in the sideline direction whereas the vortex sound source dominates the downstream acoustics.     

Effects of varying Reynolds number, blowing ratio, and internal geometry on trailing edge cutback film cooling

Three-dimensional mean velocity and concentration fields have been measured for a water flow in a pressure side cutback trailing edge film cooling geometry consisting of rectangular film cooling slots separated by tapered lands. Three-component mean velocities were measured with conventional magnetic resonance velocimetry, while time-averaged concentration distributions were measured with a magnetic resonance concentration technique for flow at two Reynolds numbers (Re) differing by a factor of 2, three blowing ratios, and with and without an internal pin fin array in the coolant feed channel. The results show that the flows are essentially independent of Re for the regime tested in terms of the film cooling surface effectiveness, normalized velocity profiles, and normalized mean streamwise vorticity. Blowing ratio changes had a larger effect, with higher blowing ratios resulting in surface effectiveness improvements at downstream locations. The addition of a pin fin array within the slot feed channel made the spanwise distribution of coolant at the surface more uniform. Results are compared with transonic experiments in air at realistic density ratios described by Holloway et al. (2002a).     

Vortex mechanism of heat transfer enhancement in a channel with spherical and oval dimples

Vortex mechanism of heat transfer enhancement in a narrow channel with dimples has been investigated numerically using LES and URANS methods. The flow separation results in a formation of vortex structures which significantly enhance heat transfer on dimpled surfaces leading to a small increase in pressure loss. The heat transfer can be significantly increased by rounding the dimple edge and use of oval dimples. To get a deep insight into flow physics LES is performed for single phase flow in a channel with a spherical dimple. The instantaneous vortex formation and separation are investigated in and around the dimple area. Considered are Reynolds numbers (based on dimple print diameter) Re_D = 20,000 and Re_D = 40,000 the depth to print diameter ratio of Δ = 0.26. Frequency analysis of LES data revealed the presence of dominating frequencies in unsteady flow oscillations. Direct analysis of the flow field revealed the presence of coherent vortex structure inclined to the mean flow. The structure changes its orientation in time causing the long period oscillations with opposite-of-phase motion. Three dimensional proper orthogonal decomposition (POD) analysis is carried out on LES pressure and velocity fields to identify spatio-temporal structures hidden in the random fluctuations. Tornado-like spatial POD structures have been determined inside dimples.     

On Recent Progress in Modelling and Simulations of Multi-scale Transfer of Mass,Momentum and Particles in Bio-medical Applications

We present a short overview of some of our most recent work that combines the mathematical modeling, advanced computer simulations and state-of-the-art experimental techniques of physical transport phenomena in various bio-medical applications. In the first example, we tackle predictions of complex blood flow patterns in the patient-specific vascular system (carotid artery bifurcation) and transfer of the so-called “bad” cholesterol (low-density lipoprotein, LDL) within the multi-layered artery wall. This two-way coupling between the blood flow and corresponding mass transfer of LDL within the artery wall is essential for predictions of regions where atherosclerosis can develop. It is demonstrated that a recently developed mathematical model, which takes into account the complex multi-layer arterial-wall structure, produced LDL profiles within the artery wall in good agreement with in-vivo experiments in rabbits, and it can be used for predictions of locations where the initial stage of development of atherosclerosis may take place. The second example includes a combination of pulsating blood flow and medical drug delivery and deposition controlled by external magnetic field gradients in the patient specific carotid artery bifurcation. The results of numerical simulations are compared with own PIV (Particle Image Velocimetry) and MRI (Magnetic Resonance Imaging) in the PDMS (silicon-based organic polymer) phantom. A very good agreement between simulations and experiments is obtained for different stages of the pulsating cycle. Application of the magnetic drug targeting resulted in an increase of up to ten fold in the efficiency of local deposition of the medical drug at desired locations. Finally, the LES (Large Eddy Simulation) of the aerosol distribution within the human respiratory system that includes up to eight bronchial generations is performed. A very good agreement between simulations and MRV (Magnetic Resonance Velocimetry) measurements is obtained. Magnetic steering of aerosols towards the left or right part of lungs proved to be possible, which can open new strategies for medical treatment of respiratory diseases.     

Large-eddy Simulation of Film Cooling Flows with Variable Density Jets

The present paper investigates the impact of the velocity and density ratio on the turbulent mixing process in gas turbine blade film cooling. A cooling fluid is injected from an inclined pipe at α=30° into a turbulent boundary layer profile at a freestream Reynolds number of Re_∞ = 400,000. This jet-in-a-crossflow (JICF) problem is investigated using large-eddy simulations (LES). The governing equations comprise the Navier–Stokes equations plus additional transport equations for several species to simulate a non-reacting gas mixture. A variation of the density ratio is simulated by the heat-mass transfer analogy, i.e., gases of different density are effused into an air crossflow at a constant temperature. An efficient large-eddy simulation method for low subsonic flows based on an implicit dual time-stepping scheme combined with low Mach number preconditioning is applied. The numerical results and experimental velocity data measured using two-component particle-image velocimetry (PIV) are in excellent agreement. The results show the dynamics of the flow field in the vicinity of the jet hole, i.e., the recirculation region and the inclination of the shear layers, to be mainly determined by the velocity ratio. However, evaluating the cooling efficiency downstream of the jet hole the mass flux ratio proves to be the dominant similarity parameter, i.e., the density ratio between the fluids and the velocity ratio have to be considered.     

Full-field measurements of flow through a scaled metal foam replica

Open-celled foam geometries show great promise in heat/mass transfer, chemical treatment, and enhanced mixing applications. Flow measurements on these geometries have consisted primarily of observations of the upstream and downstream effects the foam has on the velocity field. Unfortunately, these observations give little insight into the flow inside the foam. We have performed quantitative flow measurements inside a scaled replica of a metal foam, ϕ = 0.921, D _Cell = 2.5 mm, by Magnetic Resonance Velocimetry to better understand the fluid motion inside the foam and give an alternative method to determine the foam cell and pore sizes. Through these 3-D, spatially resolved measurements of the flow field for a cell Reynolds number of 840, we have shown that the transverse motion of the fluid has velocities 20–30% of the superficial velocity passing through the foam. This strong transverse motion creates and dissipates streamwise jets with peak velocities 2–3 times the superficial velocity and whose coherence length is strongly correlated to the cell size of the foam. This complex fluid motion is described as “mechanical mixing” and is attributed to the geometry of the foam. A mechanical dispersion coefficient, D _M, was formed which demonstrates the transverse dispersion of this geometry to be 14 times the kinematic viscosity and 10 times the thermal diffusivity of air at 20°C and 1 atm.     

Numerical study on film cooling effectiveness from shaped and crescent holes

This paper presents a comparative numerical investigation on film cooling from a row of holes injected at 35° on a flat plate with three film cooling configurations, including cylindrical hole, 15° forward diffused shaped hole, and new crescent hole. All simulations are conducted at blowing ratio of 0.6 and 1.25, length-to-diameter ratio of four and pitch-to-diameter ratio of three. Computational solutions of the steady, Reynolds averaged Navier–Stokes equations are obtained using a finite volume method. Previous successful application of a two-layer turbulence model to cylindrical hole is extended to predict film cooling for the different hole geometries. It has been found that the film cooling effectiveness of cylindrical holes obviously declined along with increasing the blowing ratio. While the forward diffused shaped hole presents a marked improvement, with a higher effectiveness at the lateral area between adjacent holes. By comparison, the crescent hole exhibits the highest film cooling effectiveness among the three configurations both in spanwise and streamwise especially downstream of the intersection of the two holes. Also, the crescent hole can restrain the vortex intensity, and then enhance the film cooling effectiveness.     

The stability and development of tip and root vortices behind a model wind turbine

An inclined turbulent jet discharging a passive scalar into a turbulent crossflow is investigated under conditions of favorable, zero and adverse streamwise pressure gradient. Experiments are conducted in water by means of magnetic resonance velocimetry and magnetic resonance concentration measurements. The velocity ratio and density ratio are equal to one for all cases. The flow configuration is relevant to film cooling technology, the molecular properties of the fluid being immaterial in the fully turbulent regime. Under favorable pressure gradient (FPG), the streamwise acceleration tilts the jet trajectory toward the wall, which would be beneficial for the film cooling performance. However, the counter-rotating vortex pair is strengthened in the accelerating flow by streamwise stretching. Also, the crossflow boundary layer is significantly thickened by increasingly adverse pressure gradient, which affects the mass transfer from the jet. Overall, the more intense counter-rotating vortices and the thinner boundary layer associated with increasingly FPG enhance the scalar dispersion into the main flow, hampering the film cooling performance in terms of surface effectiveness.     

Turbulent Heat Transfer and Large Coherent Structures in Trailing-edge Cutback Film Cooling

Film cooling is a key technology for improving the thermal efficiency and power output of gas turbines. The trailing-edge section of high-pressure turbine blades can be efficiently cooled by ejecting a film over a cutback on the pressure side of the blade. In this paper, results of Large–Eddy Simulations (LES) are presented that match an existing experimental setup. Altogether, eight simulations with the blowing ratio M varying as the only parameter were performed over a range from M?=?0.35 to 1.4. Reasonably good agreement between LES and experiments were obtained for flow field statistics and adiabatic film-cooling effectiveness η _aw. Within a limited range of blowing ratios, an increase in the blowing ratio results in a counter-intuitive decrease of the cooling effectiveness. The present work suggests a mechanism that can explain this behavior. The visualization and analysis of large coherent structures showed that there exists dominant clockwise-rotating structures that can give rise to a combined upstream- and wall-directed turbulent heat flux. This turbulent heat flux represents the main contribution of the total heat flux and causes a significantly intensified thermal mixing process, which in turn results in the counter-intuitive decrease of the cooling effectiveness.