Experiments on localized disturbances in a flat plate boundary layer. Part 2. Interaction between localized disturbances and TS-waves

Previous studies on boundary layer transition at moderate levels of free stream turbulence (FST) have shown that the transition process can be promoted by the introduction of Tollmien-Schlichting (TS) waves. In the present work the interaction between localized boundary layer disturbances and controlled TS-waves is studied experimentally. The localized disturbances are generated either from a controlled free stream perturbation, or by means of suction or injection through a slot in the flat plate surface. Both methods result in boundary layer disturbances dominated by elongated streamwise streaks of high and low velocity in the streamwise component. A strong interaction is observed preferably for high frequency TS-waves, which are damped when generated separately, and the interaction starts as a local amplification of a wide band of low-frequency oblique waves. The later stages of the transition process can be identified as a non-linear interaction between the oblique structures, leading to regeneration of new and stronger streamwise streaks.     

Receptivity of a flat plate boundary layer to a free stream axial vortex

A single free stream axial vortex of controlled strength and position was used to investigate a vortical receptivity of Blasius boundary layer. Excited boundary-layer disturbances were dominated by streamwise velocity perturbations, that grew downstream essentially linearly with the streamwise coordinate. It was shown that the disturbance characteristics are in agreement with data of previous experiments performed under natural and control conditions concerning the ‘by-pass’ transition initiated at high free stream disturbance levels. It was proved that the role of the leading edge in the receptivity process and disturbance growth under consideration is not dominant.     

Acoustic Field Effect on Laminar Turbulent Transition on a Swept Wing in the Favorable Pressure Gradient Region

The development of disturbances in a three-dimensional boundary layer on a swept wing model is studied both under natural conditions and for artificial excitation of traveling waves by an acoustic field. It is found that steady-state streamwise structures are formed in the three-dimensional boundary layer; under natural conditions a wave packet leading to turbulence is detected. When the flow is exposed to the action of an acoustic field at a frequency from the wave packet, disturbances whose velocity along the streamwise structures is equal to 0.55 of the oncoming flow velocity are formed, while the laminar-turbulent transition is displaced upstream.     

Development of three-dimensional disturbances in a boundary layer

In the region of transition from a two-dimensional laminar boundary layer to a turbulent one, three-dimensional flow occurs [1–3]. It has been proposed that this flow is formed as the result of nonlinear interaction of two-dimensional and three-dimensional disturbances predicted by linear hydrodynamic stability theory. Using many simplifications, [4, 5] performed a calculation of this interaction for a free boundary layer and a boundary layer on a wall with a very coarse approximation of the velocity profile. The results showed some argreement with experiment. On the other hand, it is known that disturbances of the Tollmin—Schlichting wave type can be observed at sufficiently high amplitude. This present study will use the method of successive linearization to calculate the primary two- and three-dimensional disturbances, and also the average secondary flow occurring because of nonlinear interaction of the primary disturbances. The method of calculation used is close to that of [4, 5], the disturbance parameters being calculated on the basis of a Blazius velocity profile. A detailed comparison of results with experimental data [1] is made. It developed that at large disturbance amplitude the amplitude growth rate differs from that of linear theory, while the spatial distribution of disturbances agree s well with the distribution given by the natural functions and their nonlinear interaction. In calculating the secondary flow an experimental correction was made to the amplitude growth rate.     

A bypass wake induced laminar/turbulent transition

The process of laminar to turbulent transition induced by a von Karman vortex street wake, was studied for the case of a flat plate boundary layer. The boundary layer developed under zero pressure gradient conditions. The vortex street was generated by a cylinder positioned in the free stream. An X-type hot-wire probe located in the boundary layer, measured the streamwise and normal to the wall velocity components. The measurements covered two areas; the region of transition onset and development and the region where the wake and the boundary layer merged producing a turbulent flow. The evolution of Reynolds stresses and rms-values of velocity fluctuations along the transition region are presented and discussed. From the profiles of the Reynolds stress and the mean velocity profile, a ‘negative' energy production region along the transition region, was identified. A quadrant splitting analysis was applied to the instantaneous Reynolds stress signals. The contributions of the elementary coherent structures to the total Reynolds stress were evaluated, for several x-positions of the near wall region. Distinct regions in the streamwise and normal to the wall directions were identified during the transition.     

Instantaneous fluctuation velocity and skewness distributions upstream of transition onset

The development of streamwise orientated disturbances through the boundary layer thickness prior to transition onset for zero-pressure gradient boundary layer flow under the influence %Tu = 4.2 is presented. The analysis concentrates on the development of the maximum positive and negative of the fluctuation velocity in order to gain further insight into the transition process. The average location of the peak negative fluctuation velocity over a range of Reynolds numbers was measured in the upper portion of the boundary layer at y/δ ≈ 0.6, whereas the location of the peak positive value was measured at y/δ ≈ 0.3. The disturbance magnitude of the negative fluctuation velocity increased beyond that of the positive as transition onset approached. The distribution and disturbance magnitude of the maximum positive and negative fluctuation velocities indicate that the initiation of transition may occur on the low-speed components of the flow that are lifted up to the upper region of the boundary layer. This is in qualitative agreement with recent direct numerical simulations on the breakdown of the flow on the lifted low-speed streaks near the boundary layer edge. The results presented in this investigation also demonstrate the increased physical insight gained by examining the distributions of the maximum positive and negative of the streamwise fluctuation velocity component associated with the low- and high-speed streaks, compared to time-averaged values, in determining what structures cause the breakdown to turbulence.     

Spectral structure and linear mechanisms in a rapidly distorted boundary layer

The aim of the present work is to investigate the spectral structure of a rapidly distorted boundary layer that develops on a flat plate in presence of a localised patch of roughness or/and grid-generated freestream turbulence. We observe that, at a certain distance downstream of the roughness patch the boundary layer exhibits a bimodal shape in the energy spectrum of the streamwise velocity fluctuations, similar to that found in a fully-turbulent boundary layer at relatively high Reynolds numbers. The physical mechanism that gives rise to the low-wavenumber peak in the spectrum, which represents long streamwise motions or “superstructures”, is identified to be the interaction of the broadband disturbances with the region of high shear near the wall in the boundary layer. We next show that the flat-plate boundary layer combined with surface roughness and grid turbulence can serve as building-block elements towards synthesising the wall-normal structure of a canonical turbulent boundary layer, in the context of large-scale streamwise motions. The rapidly distorted (or “synthetic”) boundary layer presents a simpler environment in which the coherent motions can evolve and therefore can enable a better characterisation of these motions. To further illustrate the utility of the present approach we compare results from our measurements with the predictions of the Rapid Distortion Theory (RDT). We show that the streamwise turbulence energy in the near-wall region of the rapidly distorted boundary layer grows linearly with time consistent with the RDT results on the effect of pure shear on an initially isotropic turbulence. Moreover close to the edge of the boundary layer the large-scale fluctuations experience an enhancement in the streamwise turbulence energy in accordance with the linear blocking model in the RDT framework. The present work thus highlights the importance of linear processes in wall turbulence and can help us identify aspects of it to which the linear theories can be meaningfully applied.     

Velocity statistics and flow structures observed in bypass transition using stereo PTV

It is known from smoke visualizations that in a transitional boundary layer subjected to free-stream turbulence, streaks appear and eventually break down to turbulence after wavy motions. In order to observe the streaky structures directly, a stereo particle-tracking velocimetry system using hydrogen bubbles in a water channel has been developed and validated against laser Doppler velocimetry. Mean flow statistics show good agreement with previous results. With the developed measurement system, the instantaneous spanwise distribution of the streamwise and wall-normal velocities can be measured fast enough to resolve the time development of the streaky structures. Measurements of instantaneous spanwise distributions of the streamwise and wall-normal velocity disturbances show strong negative correlation between the wall-normal and streamwise velocities in the streaks. Published online: 19 November 2002     

Measurements in the vicinity of a stagnation point

This paper presents measurements of a plane jet impinging onto a normal flat plate placed up to five jet widths from the jet outlet. The small spacing ensured that the stagnation streamline remained in the potential core of the jet. The plate shear stress distribution compared well to that from an analytical solution for the laminar development of the plate boundary layer whose external velocity was determined from the measured pressure. By comparing the shear stress measured under the present low level of free stream turbulence (0.35%) at the jet exit with that of Tu and Wood [Exp. Thermal Fluid Sci. 13 (1996) 364–373] made at about 4%, it is concluded that the turbulence level at the nozzle exit has only a second-order influence on the surface shear stress around the stagnation point. Some spanwise non-uniformity was observed in the plate shear stress, but this was confined largely to the transition region. The mean velocity, Reynolds stresses, and fluctuating pressure were measured along the stagnation streamline using a fast-response pressure probe. A significant increase in the streamwise normal stress and the mean square of the pressure fluctuations occurred before they were eventually attenuated by the plate. This increase occurred in the region where the streamwise velocity was decreasing close to the plate causing extra energy production through the normal stresses. Spectra of the velocity and pressure fluctuations showed that the increase in level was mainly due to the low frequency motion, whereas the subsequent decrease occurred at higher frequencies.     

DNS of a Laminar Separation Bubble in the Presence of Oscillating External Flow

A three-dimensional Direct Numerical Simulation (DNS) of a laminar separation bubble in the presence of oscillating flow is performed. The oscillating flow induces a streamwise pressure gradient varying in time. The special shape of the upper boundary of the computational domain, together with the oscillating pressure gradient causes the boundary layer flow to alternately separate and re-attach. When the inflow decelerates, the shear layer starts to separate and rolls up. Simultaneously the flow becomes 3D. After a transient period, the phase-averaged reverse flow inside the separation bubble reaches speeds ranging from 20 up to 150% of the free-stream velocity. During these phases, the flow is absolutely unstable and self-sustained turbulence can exist. When the inflow starts to accelerate, a spanwise roll of turbulent flow is shed from the shear layer. Shortly after this, the remainder of the separation bubble moves downstream and rejoins with the shed turbulent roll. During the flow-acceleration phase, a patch of laminar boundary layer flow is obtained. Along the flat plate, a series of turbulent patches of flow travelling downstream, separated by laminar flow can be observed, reminiscent of boundary layer flow in a turbine cascade with periodically appearing free-stream disturbances.     

Receptivity of the Swept Wing Boundary Layer to a Steady Flow Inhomogeneity

The boundary layer on a plate with an inclined blunt leading edge is investigated for a free-stream flow with a small span-periodic velocity inhomogeneity. This flow simulates the penetration of the outer turbulence into the swept wing boundary layer. It is shown that the boundary layer perturbations generated by the inhomogeneity generally have a streamwise velocity component significantly greater than the initial inhomogeneity amplitude. The dependence of the perturbations on the distance from the leading edge and the spanwise inhomogeneity period is found. It is shown that the swept wing boundary layer is less sensitive to the perturbation type in question than the straight wing boundary layer.     

Effects of free‐stream turbulence on large‐scale coherent structures of separated boundary layer transition

It has been well established that large‐scale structures, usually called coherent structures, exist in many transitional and turbulent flows. The topology and range of scales of those large‐scale structures vary from flow to flow such as counter‐rotating vortices in wake flows, streaks and hairpin vortices in turbulent boundary layer. There has been relatively little study of large‐scale structures in separated and reattached transitional flows. Large‐eddy simulation (LES) is employed in the current study to investigate a separated boundary layer transition under 2% free‐stream turbulence on a flat plate with a blunt leading edge. The Reynolds number based on the inlet free stream velocity and the plate thickness is 6500. A dynamic subgrid‐scale model is employed to compute the subgrid‐scale stresses more accurately in the current transitional flow case. Flow visualization has shown that the Kelvin–Helmholtz rolls, which have been so clearly visible under no free‐stream turbulence (NFST) are not as apparent in the present study. The Lambda‐shaped vortical structures which can be clearly seen in the NFST case can hardly be identified in the free‐stream turbulence (FST) case. Generally speaking, the effects of free‐stream turbulence have led to an early breakdown of the boundary layer, and hence increased the randomization in the vortical structures, degraded the spanwise coherence of those large‐scale structures. Copyright © 2005 John Wiley & Sons, Ltd.     

Interaction between an unsteady pressure disturbance and a hypersonic boundary layer

The development of disturbances in a hypersonic boundary layer on a cooled surface is investigated in the case in which the characteristic velocity of disturbance propagation is small but greater than the flow velocity in the wall region of the three-layer disturbed zone with interaction. The nonlinear boundary value problem formulated involves a single similarity parameter that characterizes the contribution made by the main, on average either subsonic or supersonic, region of the boundary layer to the generation of the pressure disturbance. In the linear approximation, an analytical solution and an algebraic dispersion equation are derived. It is shown that only waves exponential in time and in the streamwise coordinate can propagate downstream when themain region of the undisturbed boundary layer is subsonic on average.     

暖季强降雨对多年冻土南界斜坡路基稳定性影响分析

为阐明表面活性剂水溶液的减阻作用,使用LDV对零压梯度的二维湍流平板边界层中的CTAB 表面活性剂水溶液的湍流特性进行了实验研究. 结果表明：与牛顿流体相比,CTAB水溶液边 界层的粘性底层增厚;主流时均速度分布有被层流化的趋势,对数分布域上移;主流方向速 度湍动强度峰值减小,且远离壁面,在靠近边界层中部,出现第2峰值;垂直于主流方向的 速度湍动强度受到了大幅度抑制,雷诺应力沿着边界层厚度方向几乎为零. 结果说明CTAB 水溶液具有减弱湍流湍动各个成分相关度的作用,从而能够使雷诺应力降低、湍流能量生成 项减小最终降低流体的输送动力.     

Receptivity of the Blunt-Leading-Edge Plate Boundary Layer to Unsteady Vortex Perturbations

The response of the boundary layer on a plate with a blunt leading edge to frozen-in vortex perturbations whose vorticity is normal to the plate surface is found. It is shown that these vortices generate an inhomogeneity of the streamwise velocity component in the boundary layer. This inhomogeneity is analogous to the streaky structure developing as the degree of free-stream turbulence increases. The dependence of the amplitude and shape of the boundary layer inhomogeneity on the distance from the leading edge, the streamwise and spanwise scales, and other parameters is found for periodic and local initial perturbations. It is shown that the receptivity of the boundary layer decreases with increase in the frequency and with decrease in the streamwise perturbation scale.     

Near-field measurements and development of a new boundary layer over a flat plate with localized suction

Suction on a turbulent boundary layer is applied through a narrow strip in order to understand the effects suction can have on the boundary layer development and turbulent structures in the flow. Detailed two-component laser Doppler velocimetry (LDV) and laser-induced fluorescence (LIF) based measurements have been undertaken in regions close to the suction strip and further downstream. The region close to the strip involves a flow reversal accompanied by a change in sign for the Reynolds shear stress and strong gradients in the flow variables. The mean streamwise velocity after suction remains larger than its corresponding no-suction value. Relative to the no-suction case, the velocity fluctuations first decrease with suction followed by a slow recovery which may involve a slight overshoot. LIF visualizations indicate that compared to the no-suction case, the low-speeds streaks stay closer to the wall and exhibit a smaller amount of spanwise and wall-normal oscillations with suction. The visualization results are consistent with two-point velocity correlation measurements. The streamwise and spanwise correlation measurements indicate that the structures are disrupted or removed from the boundary layer due to suction suggesting that the original boundary layer has been strongly influenced by suction. The results are explained by the development of a new inner layer that forms downstream of the suction strip.     

减阻工况下壁面周期扰动对湍流边界层多尺度的影响

通过在平板壁面施加不同频率振幅的压电陶瓷振子周期性扰动,进行了湍流边界层主动控制减阻的实验研究.在压电陶瓷振子最大减阻工况下(80 V和160Hz),使用单丝边界层探针对压电振子自由端下游2mm处进行测量,得到不同法向位置流向速度信号的时间序列.通过对比施加控制前后的多尺度分析,发现压电振子产生的扰动只对近壁区产生影响,使得近壁区大尺度脉动降低,小尺度脉动强度增大,而对边界层的外区则基本没有影响.进一步对大尺度和小尺度的脉动信号进行条件平均,发现压电振子产生的扰动对小尺度脉动的影响在时间相位上并不均匀,小尺度脉动强度在大尺度脉动为正时比在大尺度脉动为负时具有更明显的增加.这表明壁面周期扰动主要通过使大尺度高速扫掠流体破碎为小尺度结构,来影响相应的高壁面摩擦事件,从而达到减阻效果.      

Response of the boundary layer developing over a blunt-nosed flat plate to free-stream non-uniformities

The response of the boundary layer on a flat plate with blunt nose to infinitesimally small non-uniformity in the freestream velocity along the span has been studied. The non-uniformity was shown to excite boundary-layer disturbances similar to streaks or Klebanoff modes generally observed in experiments conducted with a high level of free-stream turbulence. The boundary layer disturbances have a predominantly streamwise velocity component and exhibit transient growth. In contrast to streaks generated by streamwise vortices impinging on the sharp nose of a plate, the disturbances produced by free-stream non-uniformity interaction with a blunt nose have a different level of growth. Their maximal amplification scales with the Reynolds number, based on the size of nose bluntness and is almost independent of the spanwise period of disturbances. This difference was shown to be caused by additional amplification of disturbances via vortex lines stretching around the leading edge.     

Unsteady compressible boundary layer flow over a circular cone near a plane of symmetry

An analysis has been performed to study the unsteady laminar compressible boundary layer governing the hypersonic flow over a circular cone at an angle of attack near a plane of symmetry with either inflow or outflow in the presence of suction. The flow is assumed to be steady at time t=0 and at t>0 it becomes unsteady due to the time-dependent free stream velocity which varies arbitrarily with time. The nonlinear coupled parabolic partial differential equations under boundary layer approximations have been solved by using an implicit finite-difference method. It is found that suction plays an important role in stabilising the fluid motion and in obtaining unique solution of the problem. The effect of the cross flow parameter is found to be more pronounced on the cross flow surface shear stress than on the streamwise surface shear stress and surface heat transfer. Beyond a certain value of the cross flow parameter overshoot in the cross flow velocity occurs and the magnitude of this overshoot increases with the cross flow parameter. The time variation of the streamwise surface shear stress is more significant than that of the cross flow surface shear stress and surface heat transfer. The suction and the total enthalpy at the wall exert strong influence on the streamwise and cross flow surface shear stresses and the surface heat transfer except that the effect of suction on the cross flow surface shear stress is small.     

Numerical Modeling of the Development of a Streaky Structure in a Boundary Layer at a High Freestream Turbulence Level

The disturbances generated by external turbulence in the boundary layer on a flat plate set suddenly in motion are determined. A turbulent flow calculated by direct numerical simulation is taken as the initial conditions. The solution obtained simulates the initial stage of laminar-turbulent transition in the flat-plate boundary layer at a high turbulence level in the oncoming flow. The solution makes it possible to estimate the effects of different factors, such as nonstationarity, nonlinearity, and the parameters of the freestream velocity fluctuation spectrum, on disturbance enhancement in the boundary layer.