共查询到16条相似文献,搜索用时 46 毫秒
1.
2.
4.
当今大多数系统都遵从数据处理和数据通信设备之间的接口EIARS-232规范。因为此规范要求采用正和负信号电平,所以设计人员十分需要在单SV供电的板上增加一双电源。NationalSemiconductor公司的LM1578A开关稳压器,可用于将已有的电源变换成分离的±12V电源,以便给接日线路驱动器供电。图1为RS-232电源电路,其输入电压可低到4.2V,±12V输出电压的电流为上40mA,效率大于70%。此电路的主要特性还有:±1.25%负载调整率(从满载的10%到100%),±0.08%电… 相似文献
5.
CAN总线作为一种应用广泛的现场总线,已经从最开始的汽车领域推广到工业控制、船舶、医疗等方面。CAN是一种有效支持分布式控制或实时控制的串行通信网络,基于CAN总线的分布式控制系统在实时性、可靠性、标准性等方面具有明显的优越性。然而,CAN总线与普通的PC机却没有直接通信接口。为此,设计了CAN总线与RS232的转换器,作为PC控制CAN总线网络的直接通道,集中了RS232与CAN总线的优点,对CAN总线的使用和发展具有一定的实际意义。 相似文献
6.
7.
RS232/RS485串行通信转换器电路 总被引:2,自引:0,他引:2
<正> 对于大多数分布式控制系统来说,其通信距离一般为几十米到几千米不等,RS232接口不能满足此类系统的要求,目前广泛采用是的RS485收发器。RS485收发器采用平衡发送和差分接收,具有抑制共模干扰的能力,而且RS485收发器具有很高的灵敏度,能检测低达200mV的电压,因此,传输信号 相似文献
8.
9.
10.
11.
12.
13.
RS 232串口通信在PC机与单片机通信中的应用 总被引:13,自引:6,他引:7
在功能比较复杂的自动控制系统中,通常以工控机为上位机,单片机为下位机,RS 232串口通信是工控机和单片机之间信息传递的枢纽,采用MAX232实现TTL逻辑电平和RS 232电平之间的相互转换,如此连接,既可体现出单片机的灵活控制功能,又可发挥出PC机强大的计算和显示功能,有利于对现场信号的实时采集、处理和监控,确保了良好的人机界面的交互性。 相似文献
14.
设计了一个结构简单、使用方便、应用面广的CAN节点与RS232串口通信转换模块,详细介绍了该模块的工作原理和实现方法,即通过软硬件相结合实现电平标准和通信协议的转换,从而完成两者之间的信息传输. 相似文献
15.
16.
ABSTRACTThis paper presents a current source inverter (CSI)-based hybrid power generation system, which uses wind turbine and photovoltaic cells (PVs). A permanent magnet synchronous generator (PMSG) is connected to the CSI using a diode rectifier and a buck converter that is used to control the speed of the rotor. Another buck converter is used to control the maximum power point tracking of PVs. The operation of proposed system is studied under normal and grid voltage dip conditions. According to new grid codes, most power generating units are supposed to remain connected to the grid during voltage sag conditions and inject reactive current to grid as defined by grid codes. The CSI has fault current limiting capability that makes it appropriate to use in grid-connected applications and during voltage sag conditions in particular. The proposed system tracks the maximum power point of wind turbine and PVs under normal mode and injects required reactive current to the grid during voltage drop. However, incorporation of CSI with the inherent behaviour of wind turbine and PVs causes fault current to be within the tolerable range for power electronic devices. Simulations are carried out by using PSCAD/EMTDC software to verify the proposed system. 相似文献