Effect of tellurium on electrical and structural properties of sintered silicon nitride ceramics

The effects of tellurium (Te) additives on electrical conductivity, dielectric constant and structural properties of sintered silicon nitride ceramics have been studied. Different amounts of Te (10% and 20%) were added as sintering additives to silicon nitride ceramic powders and sintering was performed. Microstructure and composition were investigated by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The electrical conductivity and dielectric constant (ε′) increase exponentially with temperature greater than 800 K. The electrical conductivity and dielectric constant increase but activation energy decreases from 0.72 to 0.33 eV with the increase of Te concentration. However, the conductivity increases five orders of magnitude at the concentration of 10% of Te in Si₃N₄. As the Te concentration increases the sintered silicon nitride ceramics become denser. These types of samples can be used as high temperature semiconducting materials.     

Effect of sintering temperature on structure and nonlinear dielectric properties of Ba0.6Sr0.4TiO3 ceramics prepared by the citrate method

Ba_0.6Sr_0.4TiO₃ ceramics were prepared by a citrate precursor method. The structure and nonlinear dielectric properties of the resulting ceramics were investigated within the sintering temperature range 1200-1300 °C. Adopting fine Ba_0.6Sr_0.4TiO₃ powder derived from the citrate method was confirmed to be effective in reducing the sintering temperatures required for densification. The ceramic specimens sintered at 1230-1280 °C presented relative densities of around 95%. A significant influence of sintering temperature on the microstructure and nonlinear dielectric properties was detected. The discrepancy in nonlinear dielectric behavior among the specimens sintered at different temperatures was qualitatively interpreted in terms of the dielectric response of polar micro-regions under bias electric field. The specimens sintered at 1230 and 1250 °C attained superior nonlinear dielectric properties, showing relatively low dielectric losses (tan δ) of 0.24% and 0.22% at 10 kHz together with comparatively large figure of merits (FOM) of 121 and 142 at 10 kHz and 20 kV/cm, respectively.     

Low temperature fired Ni-Cu-Zn ferrite with Bi4Ti3O12

The Ni-Cu-Zn ferrites with different contents of Bi₄Ti₃O₁₂ ceramics (1-8 wt%) as sintering additives were prepared by the usual ceramic technology and sintered at 900 °C to adapt to the low temperature co-fired ceramic (LTCC) technology. The magnetic and dielectric properties of the ferrite can be effectively improved with the effect of an appropriate amount of Bi₄Ti₃O₁₂. For all samples, the ferrite sintered with 2 wt% Bi₄Ti₃O₁₂ has relatively high density (98.8%) and permeability, while the ferrite with 8 wt% Bi₄Ti₃O₁₂ has relatively good dielectric properties in a wide frequency range. The influences of Bi₄Ti₃O₁₂ addition on microstructure, magnetic and dielectric properties of the ferrite have been discussed.     

Post-sintering annealing effect on the diffuse phase transition in (Pb1−xBax)(Yb0.5Ta0.5)O3 ceramics

The effect of post sintering annealing on the dielectric response of (Pb_1−xBa_x)(Yb_0.5Ta_0.5)O₃ ceramics in the diffuse phase transition range (x=0.2) has been investigated. The samples are prepared by conventional solid-state reaction method. The samples are sintered at 1300 °C for 2 h and annealed at different temperatures (800, 900 and 1000 °C) for 8 h and at 800 °C for different time durations (8, 12 and 24 h). A significant change in the dielectric response has been observed in all the samples. The dielectric constant increases remarkably and the dielectric loss tangent decreases. The dielectric peaks of the annealed samples are observed to be more diffused with noticeable frequency dispersion compared to the as sintered sample.     

Bismuth zinc niobate (Bi1.5ZnNb1.5O7) ceramics derived from metallo-organic decomposition precursor solution

The preparation, microstructure development and dielectric properties of Bi_1.5ZnNb_1.5O₇ pyrochlore ceramics by metallo-organic decomposition (MOD) route are reported. Homogeneous precalcined ceramic powders of 13-36 nm crystallite size were obtained at temperatures ranging from 500 to 700 °C. The thermal decomposition/oxidation of the gelled precursor solution was chemically analyzed, TG/DTA, XRD, and SEM, led to the formation of a pure cubic pyrochlore phase with a stoichiometry close to Bi_1.5ZnNb_1.5O₇ which begins to form at 500 °C. The metallo-organic precursor synthesis method, where Bi, Zn and Nb ions are chelated to form metal complexes, allows the control of Bi/Zn/Nb stoichiometric ratio on a molecular scale leading to the rapid formation of bismuth zinc niobate (Bi_1.5ZnNb_1.5O₇) ceramic fine powders with pure pyrochlore structure. The powders were pressed into pellets and can be sintered at temperatures as low as 800-1000 °C. Fine crystalline ceramics with the grain size in the range of 200-500 nm have been obtained at the sintering temperature of 800 °C. The dielectric properties in high frequency to microwave range were measured and discussed.     

Study of high-coercivity sintered NdFeB magnets

Magnetic powders for sintered NdFeB magnets have been prepared by using an advanced processing method including strip casting, hydrogen decrepitation, jet milling and rubber isotropic press. The effects of Dy, Ga and Co addition on the microstructure and magnetic properties of sintered magnets have been investigated. By adopting a suitable component ratio and adjusting proper technological parameters, we have prepared high-coercivity sintered NdFeB magnets with hard magnetic properties of _jH_c=25.6 kOe, B_r=13.2 kG and (BH)_max=39.9 MGOe. The temperature coefficient of coercivity of the magnets (between 20 and 150 °C) is –0.53%/°C. The magnetic properties at high temperature satisfy the needs of permanent magnet motors.     

Double-peak resistivity transport properties of La0.67Ca0.33MnO3 ceramics

Polycrystalline samples of La_0.67Ca_0.33MnO₃ were prepared by solid-state reactions by varying the pelletization force and the sintering temperature. Lowering the sintering temperature gave rise to smaller grains and increased the overall resistivity of the ceramic. Partial melting was observed in the ceramics sintered at higher temperatures (1400-1500 °C). Additionally, these ceramics showed two distinct resistivity peaks. The resistivity peak near the magnetic transition (T_C) was sharp, whereas the second peak was a broad one observed below T_C.     

Structural, magnetic and electrical properties of NiCuZn ferrites prepared by microwave sintering method suitable for MLCI applications

Polycrystalline NiCuZn soft ferrites with stoichiometric iron were prepared by a novel microwave sintering method. The powders were calcined, compacted and sintered at 950 °C for 30 min in a microwave sintering furnace. X-ray diffraction patterns confirm the formation of single phase cubic spinel structure. The grain size was estimated using SEM micrographs. The lattice constant is found to increase with increase in zinc concentration. The sintered ferrites have been investigated for their physical, magnetic and electrical properties such as bulk density, X-ray density, porosity, anisotropy constant, initial permeability, saturation magnetization, DC resistivity, dielectric constant and dielectric loss as a function of zinc concentration. Permeability, saturation magnetization, dielectric constant and dielectric loss were found to increase while DC resistivity was found to decrease with the replacement of Zn with Ni. The present series of ferrites are found to posses properties that are suitable for the core materials in multilayer chip inductors.     

Freeze casting of aqueous coal fly ash/alumina slurries for preparation of porous ceramics

A porous mullite-matrix composite with a bimodal pore structure has been prepared by a freeze casting route using water/coal fly slurry system. The top and bottom parts of the sintered freeze cast body consisted of solid particles and micropores, which were irregularly distributed. However, the middle section was made up of small lamellar pores and porous ceramic walls, aligned along the solidification direction. The porosity of mullite composites was in the range 67-55% after sintering at 1300-1500 °C. The addition of 3Y-ZrO₂ reduced the porosity, especially material in sintered at 1500 °C due to relatively high densification. The compressive strength of the porous composite with 10 wt% 3Y-ZrO₂ addition, sintered at 1500 °C exhibited a maximum value of ∼41 MPa.     

Low-temperature sintering and microwave dielectric properties of Ca2Zn4Ti15O36 ceramics

The sintering behavior, microstructures, and microwave dielectric properties of Ca₂Zn₄Ti₁₅O₃₆ ceramics with B₂O₃ addition were investigated. The crystalline phases and microstructures of Ca₂Zn₄Ti₁₅O₃₆ ceramics with 0-10 wt% B₂O₃ addition were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). The sintering temperature of Ca₂Zn₄Ti₁₅O₃₆ ceramic was lowered from 1170 to 930 °C by 10 wt% B₂O₃ addition. Ca₂Zn₄Ti₁₅O₃₆ ceramics with 8 wt% B₂O₃ addition sintered at 990 °C for 2 h exhibited good microwave dielectric properties, i.e., a quality factor (Qf) 11,400 GHz, a relative dielectric constant (ε_r) 41.5, and a temperature coefficient of resonant frequency (τ_f) 94.4 ppm/°C.     

Influence of Ca additives on the optical and dielectric studies of sol-gel derived PbTiO3 ceramics

Sintered ceramic powders of calcium-doped lead titanate [Pb_1−xCa_xTiO₃] ceramics with different Ca dopant concentration in the range (x=0-0.35) have been prepared using a sol-gel chemical route. The sol-gel technique is known to offer better purity and homogeneity, and can yield stoichiometric powders with improved properties at relatively lower processing temperature in comparison to conventional solid-state reaction. X-ray diffraction (XRD) and Raman spectroscopy studies have been carried out to identify the crystallographic structure and phase formation. The infrared absorption spectra in the mid-IR region (400-4000 cm⁻¹) show the band corresponding to the Ti-O bond at ∼576 cm⁻¹ and is found to shift to a higher wave number 592 cm⁻¹ with increasing Ca content. The dielectric properties as a function of frequency, and phase transition studies on sintered ceramic Pb_0.65Ca_0.35TiO₃ has been investigated in detail over a wide temperature range 30-600 °C and the results are discussed.     

Dielectric properties and magnetoelectric effect of (x)NiFe2O4+(1−x)Ba0.8Sr0.2TiO3 composites

Magnetoelectric composites of NiFe₂O₄ and Ba_0.8Sr_0.2TiO₃ were prepared using conventional double-sintering ceramic method. The phase formation of magnetoelectric composites was confirmed by XRD technique. Variation of dielectric constant and loss tangent at room temperature with frequency in the range 100 Hz-1 MHz has been studied. Also the variation of dielectric constant and loss tangent with temperature and composition at fixed frequencies of 1 kHz, 10 kHz, 100 kHz and 1 MHz is reported. The static value of the magnetoelectric conversion factor was measured as a function of intensity of the magnetic field. The ME voltage coefficient of about 430 μV/cm Oe was observed for 15% NiFe₂O₄+85% Ba_0.8Sr_0.2TiO₃ composite. All the samples show linear variation of magnetoelectric conversion in the presence of static magnetic field.     

Magnetic,magnetoelectric and dielectric behavior of CoFe2O4–Pb(Fe1/2Nb1/2)O3 particulate and layered composites

Magnetic, magnetoelectric and dielectric properties of multiferroic CoFe₂O₄–Pb(Fe_1/2Nb_1/2)O₃ composites prepared as bulk ceramics were compared with those of tape cast and cofired laminates consisting of alternate ferrite and relaxor layers. X-ray diffraction analysis and Scanning Electron Microscope observations of ceramic samples revealed two-phase composition and fine grained microstructure with uniformly distributed ferrite and relaxor phases. High and broad maxima of dielectric permittivity attributed to dielectric relaxation were found for ceramic samples measured in a temperature range from −55 to 500 °C at frequencies 10 Hz–2 MHz. Magnetic hysteresis, zero-field cooled (ZFC) and field cooled (FC) curves, and dependencies of magnetization on temperature for both magnetoelectric composites were measured with a vibrating sample magnetometer in an applied magnetic field up to 80 kOe at 4–400 K. The hysteresis loops obtained for composites are typical of a mixture of the hard magnetic material with a significant amount of the paramagnet. The bifurcation of ZFC–FC magnetizations observed for both composites implies spin-glass behavior. Magnetoelectric properties at room temperature were investigated as a function of dc magnetic field (0.3–7.2 kOe) and frequency (10 Hz–10 kHz) of ac magnetic field. Both types of composites exhibit a distinct magnetoelectric effect. Maximum values of magnetoelectric coefficient attained for the layered composites exceed 200 mV/(cm Oe) and are almost three times higher than those for particulate composites.     

Phase evolution and microwave dielectric properties of Bi3SbO7 ceramic

The Bi₃SbO₇ ceramic was prepared by the solid state reaction method and its phase evolution at different temperatures was studied. Low temperature phase α-Bi₃SbO₇ was formed at about 890 °C and it started to transform to high temperature phase β-Bi₃SbO₇ at about 960 °C. Microwave dielectric constants of α-Bi₃SbO₇ ceramic and β-Bi₃SbO₇ ceramic were 43.2 and 37.6, Qf value were 2080 and 5080 GHz, respectively. TCF of α-Bi₃SbO₇ ceramic was near zero and TCF of β-Bi₃SbO₇ ceramic was about −120 ppm/°C. The Bi₃SbO₇ ceramic is a promising candidate for low temperature co-fired ceramic (LTCC) technology due to its large dielectric constant, low dielectric loss at microwave region, low sintering temperature and simple composition.     

Decrease of loss in dielectric properties of TbMnO3 by adding TiO2

Low-frequency (10²-10⁵ Hz) dielectric properties of TbMnO₃+xTiO₂ (x=0.33, 1, 3) ceramic composites, which were fabricated by conventional solid-state reaction, were investigated from 360 to 77 K. Very high dielectric constants and interesting temperature dependence of the dielectric properties were observed in the present composite ceramics. When compared to the high dielectric loss of the polycrystalline TbMnO₃, the loss of TbMnO₃+xTiO₂ (x=0.33, 1, 3) decreased with the increasing TiO₂. Especially for TbMnO₃+1TiO₂, the dielectric loss decreased remarkably, while the dielectric constant was still very high, which are more favorable for practical applications.     

Structural,magnetic and electrical properties of Co1−xZnxFe2O4 synthesized by co-precipitation method

Nanoparticles of Co_1−xZn_xFe₂O₄ with stoichiometric proportion (x) varying from 0.0 to 0.6 were prepared by the chemical co-precipitation method. The samples were sintered at 600 °C for 2 h and were characterized by X-ray diffraction (XRD), low field AC magnetic susceptibility, DC electrical resistivity and dielectric constant measurements. From the analysis of XRD patterns, the nanocrystalline ferrite had been obtained at pH=12.5–13 and reaction time of 45 min. The particle size was calculated from the most intense peak (3 1 1) using the Scherrer formula. The size of precipitated particles lies within the range 12–16 nm, obtained at reaction temperature of 70 °C. The Curie temperature was obtained from AC magnetic susceptibility measurements in the range 77–850 K. It is observed that Curie temperature decreases with the increase of Zn concentration. DC electrical resistivity measurements were carried out by two-probe method from 370 to 580 K. Temperature-dependent DC electrical resistivity decreases with increase in temperature ensuring the semiconductor nature of the samples. DC electrical resistivity results are discussed in terms of polaron hopping model. Activation energy calculated from the DC electrical resistivity versus temperature for all the samples ranges from 0.658 to 0.849 eV. The drift mobility increases by increasing temperature due to decrease in DC electrical resisitivity. The dielectric constants are studied as a function of frequency in the range 100 Hz–1 MHz at room temperature. The dielectric constant decreases with increasing frequency for all the samples and follow the Maxwell–Wagner's interfacial polarization.     

Microwave-absorbing properties of shape-optimized carbonyl iron particles with maximum microwave permeability

The microwave-absorbing properties for different shapes of carbonyl-iron particles prepared by the high-energy planetary ball milling with 40 vol% in epoxy resin matrix have been investigated. Higher value of magnetic permeability and permittivity can be obtained in the composites for thin flake carbonyl iron than spherical powders. The results are attributed to reduction of eddy current loss, orientation of magnetic moment and space-charge polarization with the shape change from spherical powders to thin flake particles. As the iron flakes with 0.4 μm in thickness as the absorbent fillers, the minimum RL value of −6.20 dB was observed at 4.57 GHz with thickness of 1 mm. The minimum reflection loss (RL) shifts to lower frequency and the value declines with change from spherical powders to thin flakes. It results from the considerable dielectric loss in the absorbing materials.     

The effect of filler on the temperature coefficient of the relative permittivity of PTFE/ceramic composites

High permittivity and low-loss ceramic fillers have been prepared by means of the solid state ceramic route. Ceramic-filled composites were prepared by the Sigma Mixing, Extrusion, Calendering, which was followed by the Hot pressing (SMECH) process. The microwave dielectric properties of the composites were studied using X-band waveguide cavity perturbation technique. The temperature coefficient of the relative permittivity of the composites was investigated in the 0-100 °C temperature range using a hot and cold chamber coupled with an impedance analyzer. The temperature coefficient of the relative permittivity of the composites showed strong dependence on the temperature coefficient of the relative permittivity of the filler material. In the present study, a high-permittivity polymer/ceramic composite, having τ_εr ∼63 ppm/K, has been realized. This composite is suitable for outdoor wireless applications.     

Characterization of enhanced emission from excimer laser treated ZnO ceramics using one- and two-photon luminescence spectroscopy and microscopy

The effects of excimer laser irradiation on the surface structure and luminescence of sintered ZnO ceramics were investigated. Photoluminescence spectra of three materials (as-prepared ZnO ceramic, the ceramic blackened by high-energy irradiation and the recovered ceramic treated using lower-energy irradiation) were compared in the visible region at room temperature and 10 K. Each material exhibited a green luminescence band but the blackened ZnO ceramics had the strongest emission in the visible region while the recovered ceramics had significantly shorter decay times.     

Synthesis of fine-crystalline Ba0.6Sr0.4TiO3-MgO ceramics by novel hybrid processing route

We report the use of a novel powder-in-sol precursor hybrid processing route to synthesize dense, homogeneous, and fine-crystalline Ba_0.6Sr_0.4TiO₃-MgO (BST-MgO) ceramics as well as the study of the sintering behavior, microstructures, and dielectric properties of the ceramics. Nanosized BST powders are dispersed into BST sol-gel precursor and uniformly distributed BST slurry is obtained after ball-milling mixing. Mg(NO₃)·6H₂O solution is added to the BST slurry to give homogeneous BST-MgO slurry upon ball-milling mixing. The BST-MgO slurry is dried and calcined prior to pressing and sintering at low temperatures of 1200-1300 °C to form the ceramics. The ceramics possess very low dielectric loss tangent below 0.005 for frequency above 1 kHz and for temperature in the range −190-80 °C. The dielectric constant and dielectric tunability increase, while the ferroelectric transition broadening decreases, with increasing average grain size.