Effect of branching in base polymer on ionic conductivity in hyperbranched polymer electrolytes

Novel hyperbranched polymer, poly[bis(diethylene glycol)benzoate] capped with a 3,5-bis[(3′,6′,9′-trioxodecyl)oxy]benzoyl group (poly-Bz1a), was prepared, and its polymer electrolyte with LiN(CF₃SO₂)₂, poly-Bz1a/LiN(CF₃SO₂)₂ electrolyte, was all evaluated in thermal properties, ionic conductivity, and electrochemical stability window. The poly-Bz1a/LiN(CF₃SO₂)₂ electrolyte exhibited higher ionic conductivity compared with a polymer electrolyte based on poly[bis(diethylene glycol)benzoate] capped with an acetyl group (poly-Ac1a), and the ionic conductivity of poly-Bz1a/LiN(CF₃SO₂)₂ electrolyte was to be 7×10⁻⁴ S cm⁻¹ at 80 °C and 1×10⁻⁶ S cm⁻¹ at 30 °C, respectively. The existence of a 3,5-bis[(3′,6′,9′-trioxodecyl)oxy]benzoyl group as a branching unit present at ends in the base polymer improved significantly ionic conductivity of the hyperbranched polymer electrolytes. The polymer electrolyte exhibited the electrochemical stability window of 4.2 V at 70 °C and was stable until 300 °C.     

Solid polymer electrolytes based on squaric acid structure

Poly(squarate)s (PPS-1 and PPS-2) were synthesized by the reaction of squaryl dichloride with hydroquinone for PPS-1 and with 2,5-diethoxy-1,4-bis(trimethylsilyloxy)benzene for PPS-2, and the ionic conductivities, thermal properties, and electrochemical and thermal properties of their polymer electrolytes with LiN(CF₃SO₂)₂ were investigated. The ionic conductivity increased with increasing the lithium salt concentration for the PPS-1–LiN(CF₃SO₂)₂ electrolyte, and the highest ionic conductivities of 8.60 × 10⁻⁵ S/cm at 100 °C and 9.57 × 10⁻⁸ S/cm at 30 °C were found at the [Li] to [O] ratio of 2:1. And also, the ionic conductivity for the PPS-1–LiN(CF₃SO₂)₂ electrolyte increased with an increase in the lithium salt concentration, reached a maximum value at the [Li] to [O] ratio of 1:2, and then decreased. The highest ionic conductivity was to be 1.04 × 10⁻⁵ S/cm at 100 °C and 1.71 × 10⁻⁸ S/cm at 30 °C, respectively. Both polymer electrolytes exhibited relatively better electrochemical and thermal stabilities. Addition of the PPS-1 as a plasticizer into the poly(ethylene oxide) (PEO)–LiN(CF₃SO₂)₂ electrolyte system suppressed the crystallization of PEO, and improved the ionic conductivity at room temperature. Invited paper dedicated to Professor W. Weppner on his 65th birthday.     

Ionic conduction in plasticized PVC/PAN blend polymer electrolytes

Blended polymer electrolytes with poly(vinyl chloride) (PVC)–poly(acrylonitrile) (PAN) were prepared with different plasticizer concentrations and constant lithium perchlorate (LiClO₄) ratio by the solution-casting technique. The structure and complexation of the prepared films were studied by X-ray diffraction and Fourier transform infrared spectroscopy. The effect of the plasticizer on the ionic conduction in these electrolytes was investigated using alternating current impedance measurement and discussed. The temperature-dependant ionic conductivity was carried out in the range 302–373 K. The prepared films were also examined by thermogravimetry/differential thermal analysis to determine their thermal stability.     

Effect of hot pressing on the ionic conductivity of the PEO/LiCF3SO3 based electrolyte membranes

PEO/LiCF₃SO₃ (LiTFS) /Ethylene carbonate (EC) polymer electrolyte membranes were prepared with a solution casting method followed by a hot pressing process. The effect of the hot pressing process on the in-plane conductivity of the PEO electrolyte membranes was evaluated using a four-electrode AC impedance method. The composition, morphology, and microstructure of the composite polymer electrolyte were characterized using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and differential scanning calorimetry (DSC). The AC impedance measurement results indicate that the hot pressing process can increase the room temperature conductivity of the membranes 14 times to 1.7 × 10^− 3 S cm^− 1 depending upon the duration of the hot pressing process. The SEM, FTIR, XRD, and DSC results indicate that the hot pressing process could increase the amorphous part of the polymer electrolyte membrane or convert large spherulite crystals into nano-sized crystals.     

3-D microbattery electrolyte by self-assembly of oligomers

This paper reports the preparation and characterization of novel thin film electrolytes by UV cross-linking of poly(propylene glycol) diacrylate in the presence of polyetheramine (glyceryl poly(oxypropylene)triamine) and LiTFSI. The oligomeric surfactant polyetheramine facilitates self-assembly of the electrolyte, enabling it to be applied conformally onto a complex substrate which is necessary for 3D-microbatteries, while the acrylate network supplies mechanical stability. Conformal coatings onto LiFePO₄ electrodes and Cu nanopillars were confirmed by SEM. Ionic conductivities of 3.5 × 10^− 6 and 5.8 × 10^− 5 S/cm were measured at room temperature and 60 °C, respectively, at Li:O = 1:20 and PEA:PPGDA = 2:1 ratios. The electrochemical stability window test showed that the electrolyte is stable above 5.0 V vs. Li/Li⁺. Thermal analyses by TGA and DSC demonstrated that the polymer electrolyte is amorphous and thermally stable up to 300 °C.     

Effect of molecular weight on conductivity of polymer electrolytes

The ionic conductivity, σ, of mixtures of poly(ethylene oxide) (PEO) and lithium bis(trifluoromethanesulfone)imide (LiTFSI) was measured as a function of molecular weight of the PEO chains, M, over the range 0.2-5000 kg/mol. Our data are consistent with an expression σ = σ₀ + K/M proposed by Shi and Vincent [Solid State Ionics 60 (1993)] where σ₀ and K are exponential and linear functions of inverse temperature respectively. Explicit expressions for σ₀ and K are provided.     

Lithium ion transport and ion-polymer interaction in PEO based polymer electrolyte plasticized with ionic liquid

The polyethylene oxide (PEO) based lithium ion conducting polymer electrolytes complexed with lithium trifluoromethanesulfonate (LiCF₃SO₃ or LiTf) plasticized with an ionic liquid 1-ethyl 3-methyl imidazolium trifluoromethanesulfonate (EMITf) have been reported. Morphological, spectroscopic, thermal and electrochemical investigations demonstrate promising characteristics of the polymer films, suitable as electrolyte in various energy storage/conversion devices. Significant structural changes have been observed in the polymer electrolyte due to the ionic liquid addition, investigated by X-ray diffraction (XRD) and optical microscopy. The ion-polymer interaction, particularly the interaction of imidazolium cation with PEO chains, has been evidenced by IR and Raman spectroscopic studies. The optimized composition of the polymer electrolyte i.e. PEO_25.LiTf + 40 wt.% EMITf offer room temperature ionic conductivity of ~ 3 × 10^− 4 S cm^− 1 with wide electrochemical stability window and excellent thermal stability. The ‘σ versus 1/T’ curves show apparent Arrhenius behavior below and above melting temperature. The ionic conductivity has been observed due to Li⁺ ions, as confirmed from ⁷Li-NMR studies, though the component ions of ionic liquid and anions also contribute significantly to the overall conductivity.     

Effects of cobalt metal addition on sintering and ionic conductivity of Sm(Y)-doped ceria solid electrolyte for SOFC

The effects of cobalt addition (0.5 and 1 wt.%) on densification and ionic conductivity of Ce_0.9Sm_0.1O_1.95 (10SDC) and Ce_0.9Sm_0.075Y_0.025O_1.95 (2.5Y-SDC) have been studied. X-ray diffraction (XRD) showed that Co had changed to Co₃O₄ and Co₃O₄ + CoO after firing at 900 °C and 1300 °C respectively. The addition of Co promoted densification to occur at lower temperatures with a more uniform grain growth and greatly improved both grain boundary and bulk conductivity for 10SDC. Significant improvement of grain boundary for the 2.5Y-SDC samples was obtained, even at 1300 °C sintering, while bulk conductivity was slightly improved. Rapid grain growth along with improvement of ionic conductivity was observed when the samples were sintered further at higher temperature. Superior ionic conductivity of the 2.5Y-SDC samples with Co addition to that of the bare 10SDC suggested the potential use of Co as the co-dopant in this system to reduce the content of costly rare earth usage.     

A study on the blending effect of polyvinyledene fluoride in the ionic transport mechanism of plasticized polyvinyl chloride + lithium perchlorate gel polymer electrolytes

The gel polymer electrolytes composed of the blend of polyvinylchloride (PVC) and polyvinylidene fluoride (PVdF) as host polymers, the mixture of ethylene carbonate (EC) and propylene carbonate (PC) as a plasticizer, and LiClO₄ as a salt was studied. An attempt was made to investigate the effect of PVdF in the plasticized PVC + LiClO₄ system in three blend ratios. The differential scanning calorimetry study confirms the formation of polymer–salt complex and miscibility of the PVC and PVdF. The X-ray diffraction results of plasticized PVC (S1, S2, S3) and PVdF-blended films (S4, S5, S6) were compared, in that an increase in PVC concentration decreases the degree of crystallinity for S1 and S3, respectively, but drastically increases for PVC (S2). The increase in PVC content has not accounted in the conductivity studies also noted. However, the blending effect of PVdF showed decreases in crystallinity homogeneously for (S6 > S5 > S4), which were reflected in ionic conductivity measurements. The surface morphology of the films were also studied by scanning electron microscope, and it corroborates the same. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006.     

Entropy and ionic conductivity

It is known that the ionic conductivity can be obtained by using the diffusion constant and the Einstein relation. We derive it here by extracting it from the steady electric current which we calculate in three ways, using statistics analysis, an entropy method, and an entropy production approach.     

Effect of plasticizer on electrical conductivity and cell parameters of (PVC+KBrO<Subscript>3</Subscript>) polymer electrolyte system

The effect of a plasticizer dimethyl formamide (DMF) on the properties of a potassium ion conducting electrolyte based on polyvinyl chloride (PVC) complexed with potassium bromate (KBrO₃) prepared using solution-cast technique was investigated. Various experimental techniques, such as electrical conductivity (composition and temperature dependence) and transport number measurements, were used to characterize these polymer electrolyte films. It was found that the addition of plasticizer (DMF) significantly improved the ionic conductivity. Transport number for K⁺ ion ranged from 0.95 to 0.97 depending on the composition and temperature. Electrochemical cells of configuration K/PVC+KBrO₃/(I₂+C+electrolyte) and K/PVC+KBrO₃+plasticizer/(I₂+C+electrolyte) were fabricated. The discharge characteristics of the cells were studied under a constant load of 100 kΩ. The open-circuit voltage, short-circuit current, and discharge time for the plateau region were measured. The PVC+KBrO₃ polymer electrolyte system with added plasticizer showed an increased discharge time with respect to pure PVC+KBrO₃ electrolyte system. The features of complexation of the electrolytes were studied by X-ray diffraction.     

Effect of elaboration parameters on ionic conductivity for PECVD fuel cell electrolyte

Integration of fuel cells for nomad applications (like cell phone or notebook) is characterized by small dimensions and high performances of the component. To obtain theses properties, one of possibilities is to increase the active surface with patterned substrate. Then, the actual planar batteries must be replaced by 3D batteries. Most of deposition methods, used in the actual fuel cell process flow, are not compatible with the 3D deposition because they did not provide conformal coating. That is why we develop a PECVD electrolyte because this method is known to be compatible with 3D depositions. The PECVD electrolyte is based on a fluorocarboxylic acid, which is able to conduct protons. The obtained layer is a protonic conductor that can absorb water and stop hydrogen. Effects of elaboration parameters like pressure, power, or acid concentration on the ionic conductivity will be presented. Paper presented at the 11th EuroConference on the Science and Technology of Ionics, Batz-sur-Mer, Sept. 9–15, 2007.     

Study on ionic conductivity of polymer electrolyte plasticized with PEG–aluminate ester for rechargeable lithium ion battery

We have synthesized poly(ethylene glycol) (PEG)-aluminate ester as a plasticizer for solid polymer electrolytes. The thermal stability, ionic conductivity and electrochemical stability of the polymer electrolyte which consist of poly(ethylene oxide) (PEO)-based copolymer, PEG–aluminate ester and lithium bis-trifluoromethanesulfonimide (LiTFSI) were investigated. Addition of PEG–aluminate ester increased the ionic conductivity of the polymer electrolyte, showing greater than 10^− 4 S cm^− 1 at 30 °C. The polymer electrolyte containing PEG–aluminate ester retained thermal stability of the non-additive polymer electrolyte and exhibited electrochemical stability up to 4.5 V vs. Li⁺/Li at 30 °C.     

Effect of monocationic ionic liquids as electrolyte additives on the electrochemical and thermal properties of Li-ion batteries

The conventional electrolyte system has been compared with the ionic liquid (IL) additive containing electrolyte system at room temperature as well as elevated temperature. In this work, two types of monocationic ILs such as 1-butyl-3-methylpyrrolidinium hexafluorophosphate (Pyr IL) and 1-ethyl-3-methylimidazolium hexafluorophosphate (IMI IL) are added as an additive at two different weight ratios in 1.15 M LiPF₆ (EC/EMC = 3/7 v/v) electrolyte solution, the structural, electrochemical and thermal characteristics of LiNi_0.80Co_0.15Al_0.05O₂ (NCA)/carbon full-cell in different electrolyte formulations have been reconnoitered. X-ray diffraction (XRD) studies have proved that IL as an electrolyte additive does not alter the structural stability of cathode materials after cycling. Under room temperature, Pyr IL additives at 1 wt% and 3 wt% deliver better cycleability than others, with the retention ratios of 93.62% and 92.8%, respectively. At elevated temperature, only 1 wt% Pyr IL additive is giving stable capacity retention ratio of 80.74%. Ionic conductivity and self-extinguishing time (SET) values are increasing with respect to the amount of additive added to the electrolyte. Thermal studies reveal that 3 wt% Pyr IL is favorable regarding the safety of the battery as it shows shifting of peak to higher temperature of 272.10 °C. Among the IL additives evaluated in this study, addition of 1 wt% Pyr IL is the most desirable additive for achieving the best cycling performance as well as thermal behavior of Li-ion batteries.     

固体电解质Rb4Cu16I7Cl13制备及离子导电性研究

液态固体电解质材料的离子电导率低,安全性问题在一定程度上限制了其发展与应用,而固体电解质材料在室温下具有很好的稳定性和高的离子电导率值,具有较好的应用前景.本文采用机械化学球磨法制备固体电解质Rb₄Cu₁₆I₇Cl₁₃粉末,探索制备工艺和球磨参数,对其晶体结构进行解析、观察粉体微观结构、通过交流阻抗谱及等效电路分析得到了离子电导率与活化能、并详细探讨其离子传导性能与晶体结构的关系以及化学成分稳定性进行研究.实验结果表明,在480 rpm转速下球磨6 h时可得到纯的固体电解质Rb₄Cu₁₆I₇Cl₁₃物相.粉体晶粒尺寸分布均匀,均在20 nm-400 nm之间,室温下固体电解质Rb₄Cu₁₆I₇Cl₁₃离子电导率可达到0.213 S/cm且活化能为0.087(9)eV.在真空干燥条件下存放5天和12天后观察了微观形貌和化学稳定性...     

传感器电解质材料热膨胀性能和热稳定性变化规律研究

以ZrO2固体电解质材料为例,研究氧传感器电解质材料原子振动特点和热膨胀系数及其热稳定性随温度和时间的变化规律,探讨原子非简谐振动的影响。结果表明：原子振动的频率、阻尼系数,在简谐近似下为常数,在考虑到非简谐效应后随温度升高而增大;原子平均位移和热膨胀系数在简谐近似下为零,在考虑到非简谐效应后随温度升高而增大,随的时间的增长而减小;热膨胀性能稳定性温度系数随温度的升高而减小,随时间的增长而增大,即使用时间越长,材料的热膨胀性能稳定性越低;温度越高,热膨胀性能越稳定;非简谐情况下的原子振动的频率、阻尼系数和热膨胀系数与简谐近似下的差值随温度的升高而增大,即温度越高,非简谐效应越显著。     

Effects of Al2O3 nanofiller and EC plasticizer on the ionic conductivity enhancement of solid PEO-LiCF3SO3 solid polymer electrolyte

A solid polymer electrolyte (SPE) is synthesized by solution casting technique. The SPE uses poly(ethylene oxide) PEO as a host matrix doped with lithium triflate (LiCF₃SO₃), ethylene carbonate (EC) as plasticizer and nano alumina (Al₂O₃) as filler. The polymer electrolytes are characterized by Impedance Spectroscopy (IS) to determine the composition of the additive which gives the highest conductivity for each system. At room temperature, the highest conductivity is obtained for the composition PEO-LiCF₃SO₃-EC-15%Al₂O₃ with a value of 5.07 10^− 4 S/cm. The ionic conductivity of the polymer electrolytes increases with temperature and obeys the Arrhenius law. X-ray diffraction (XRD) and differential scanning calorimetry (DSC) studies indicate that the conductivity increase is due to an increase in amorphous content which enhances the segmental flexibility of polymeric chains and the disordered structure of the electrolyte. Fourier transform infrared spectroscopy (FTIR) spectra show the occurrence of complexation and interaction among the components. Scanning electron microscopy (SEM) images show the changes morphology of solid polymer electrolyte.     

Comblike polymer electrolyte with main chain glass transition near room temperature

A new amorphous comblike polymer (CBP) based on methylvinyl ether/maleic anhydride altering copolymer backbone and on oligooxyethylene side chain was synthesized. The dynamic mechanical properties of CBP and its Li salt complexes were investigated by means of DDV-ll-EA type viscoelastic spectrometry. Results showed that there were two glass transitions (-transition and β-transition) in the temperature range from − 100 to 100 °C. The β-transition was assigned to oligo-PEO side chains and the temperature of β-transition increases with increasing Li salt content. The -transition was assigned to the main chain of CBP. The temperature of the -transition (T) is also dependent upon the Li-salt content, but not monotonie. The value of T lies between 30–45 °C in the Li salt concentration range studied, near room temperature. It was found that the CBP-Li salt complexes showed an unusual dependence of ionic conductivity on Li salt content. There are two peaks in the plot of the ionic conductivity vs. Li salt concentration, which has been ascribed to the movability of the CBP main chain at ambient temperature. The temperature dependence of the ionic conductivity indicated that the Arrhenius relationship was not obeyed, and the plot of log σ against 1/(T − T₀) showed the unusual dual VTF behavior when using side chain glass transition temperature (T_β) as T₀.     

Investigations on the effect of complexation of NaF salt with polymer blend (PEO/PVP) electrolytes on ionic conductivity and optical energy band gaps

Sodium ion conducting polymer blend electrolyte films, based on polyethylene oxide (PEO) and polyvinyl pyrrolidone (PVP) complexed with NaF salt, were prepared using solution casting technique. The complexation of the salt with the polymer blend was confirmed by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and UV-vis spectroscopy. Electrical conductivity of the films was measured with impedance analyzer in the frequency range of 1 Hz to 1 MHz and in the temperature range of 303-348 K. It was observed that the magnitude of conductivity increased with the increase in the salt concentration as well as the temperature. UV-vis absorption spectra in wavelength region of 200-800 nm were used to evaluate the optical properties like direct and indirect optical energy band gaps, optical absorption edge. The optical band gaps decreased with the increase in Na⁺ ion concentration. This suggests that NaF, as a dopant, is a good choice to improve the electrical properties of PEO/PVP polymer blend electrolytes.     

Poly(ethylene oxide-co-epichlorohydrin)/NaI: a promising polymer electrolyte for photoelectrochemical cells

We have investigated the thermal and ionic conductivity properties of the elastomer poly(ethylene oxide-co-epichlorohydrin) filled with NaI and I₂. The reason for using this composition is its potential application as electrolyte in photoelectrochemical cells. This copolymer was characterized as a function of NaI concentration, temperature and relative humidity. According to the data obtained, the Na⁺ ion interacts with the ethylene oxide repeating units by means of Lewis type acid–base interactions. The empirical Vogel–Tamman–Fulcher equation was used to model the conductivity and temperature relationships, indicating that the conduction occurs in the amorphous phase of the copolymer. The sample with 9.0% (w/w) of NaI presents a conductivity of 1.5×10⁻⁵ S cm⁻¹ in a dry atmosphere (30°C, [H₂O]<1 ppm) and 2.0×10⁻⁴ S cm⁻¹ at 86% relative humidity (22°C).