Peeling of polydimethylsiloxane adhesives at low velocities: Cohesive failure

This work presents results obtained in 90‐degree peeling tests at low velocities in the case of Newtonian adhesives, when failure is cohesive. Peeling experiments are described and consider the influence of the thickness, viscosity, and surface tension of the adhesive, as well as the backing rigidity. A simple model, based on lubrication effects in thin films, is considered and compared with the measurements, when peeling is a two‐dimensional phenomenon. Furthermore, a criterion for predicting the transition between the two‐dimensional regime and the three‐dimensional regime at higher velocities is proposed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 145–157, 2005     

Click chemistry in materials synthesis. III. Metal‐adhesive polymers from Cu(I)‐catalyzed azide–alkyne cycloaddition

1,2,3‐Triazole‐based polymers generated from the Cu(I)‐catalyzed cycloaddition between multivalent azides and acetylenes are effective adhesive materials for metal surfaces. The adhesive capacities of candidate mixtures of azide and alkyne components were measured by a modified peel test, using a customized adhesive tester. A particularly effective tetravalent alkyne and trivalent azide combination was identified, giving exceptional strength that matches or exceeds the best commercial formulations. The addition of Cu catalyst was found to be important for the synthesis of stronger adhesive polymers when cured at room temperature. Heating also accelerated curing rates, but the maximum adhesive strengths achieved at both room temperature and high temperature were the same, suggesting that crosslinking reaches the same advanced point in all cases. Polytriazoles also form adhesives to aluminum, but copper is bound more effectively, presumably because active Cu(I) ions may be leached from the surface to promote crosslinking and adhesion. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5182–5189, 2007     

Investigation of shear failure mechanisms of pressure‐sensitive adhesives

We report new experiments investigating the failure mechanisms in shear, of thin layers of acrylic pressure‐sensitive adhesives (PSA). We have developed a novel experimental device able to shear a soft adhesive layer confined between a rigid hemispherical lens and a rigid glass substrate. Using the resources of in situ contact visualization, the nonhomogeneous deformation of the layer and the shear failure processes were observed optically. Depending on the rheological properties of the adhesive, ratios of the contact radius over the layer thickness of 10–30 were achieved, mimicking well the contact conditions encountered in a thin adhesive layer within a joint. When the adhesive was weakly crosslinked, we observed a fluid‐like behavior and could measure a reasonable value for the viscosity of the PSA, implying that flow can occur in the layer and failure will occur by creep. On the other hand, for a more crosslinked adhesive, closer to what is used in applications, a stick‐slip peeling behavior was observed, which involves a coupling between peeling mechanisms at the leading edge of the contact and interfacial slippage. Such a process suggests a failure by fracture rather than by creep. Interestingly, the peeling mechanisms and the associated stress levels change significantly when the layer becomes as thin as 20 μm, implying a fracture process that is controlled by a critical energy release rate in shear G_IIc rather than by a critical shear stress causing failure of the interfacial bonds. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3316–3330, 2005     

Molecular and nanoscale factors governing pressure‐sensitive adhesion strength of viscoelastic polymers

Pressure‐sensitive adhesives (PSAs) are finding increasing applications in various areas of industry and medicine. PSAs are a special class of viscoelastic polymers that form strong adhesive joints with substrates of varying chemical nature under application of light external bonding pressures (1–10 Pa) over short periods of time (1–5 s). To be a PSA, a polymer should possess both high fluidity under applied bonding pressure, to form good adhesive contact, and high cohesive strength and elasticity, which are necessary for resistance to debonding stresses and for dissipation of mechanical energy at the stage of adhesive bond failure under detaching force. For rational design of novel PSAs, molecular insight into mechanisms of their adhesive behavior is necessary. As shown in this review, strength of PSA adhesive joints is controlled by a combination of diffusion, viscoelastic, and relaxation mechanisms. At the molecular level, strong adhesion is the result of a narrow balance between two generally conflicting properties: high cohesive strength and large free volume. These conflicting properties are difficult to combine in a single polymer material. Individually, high cohesive interaction energy and large free volume are necessary but insufficient prerequisites for PSA strength. Evident correlations are observed between the adhesive bond strengths of different PSAs, and their relaxation behaviors are described by longer relaxation times. Innovative PSAs with tailored properties can be produced by physical mixing of nonadhesive long‐ and short‐chain linear parent polymers, with groups at the two ends of the short chains complementary to the functional groups in the recurring units of the long chains. Although chemical composition and molecular structure of such innovative adhesives are unrelated to those of conventional PSAs, their mechanical properties and adhesive behaviors obey the same general laws, such as the Dahlquist's criterion of tack. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

High strength reversible adhesive closures

Closures such as buttons, clasps, zippers, and hook‐and‐loops find widespread use in daily life, and all work by mechanical interlocking. However, these traditional closures are often rigid, lose performance with age, and can produce a harsh sound during use. Here high strength (>50 N cm^?2), reusable, and nearly silent closure devices are fabricated based on recently developed fibril‐less gecko‐inspired adhesives. Guided by a reversible adhesion scaling law, the closure force capacity is tuned by modifying the closure materials and geometry. A simple analytical model is presented which accurately predicts system performance, based on the reversible adhesion scaling parameter. The force capacity of these adhesive closures is measured and compared to commercially‐available hook‐and‐loop closures, and it is found that the adhesive closures sustain forces that are 4.4 times greater for comparable geometry. The sound of release is also quantified and shown to be minimal for adhesive closures. This work provides motivation to develop new high strength, reusable closures for commercial and industrial applications. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 1783–1790     

Poly(acrylate/epoxy) hybrid adhesives for low‐surface‐energy plastic adhesion

The formulation, polymerization, and performance of a new class of low‐surface‐energy adhesives for plastics are described. The polymerization involves the simultaneous room‐temperature polymerization of polyoxirane monomers in an acrylic monomer phase. The polymerization of the acrylic phase and adhesion promotion to plastics are catalyzed after the decomplexation and oxidation of trialkylborane–amine complexes. The polymerization of the epoxy phase is catalyzed with a Lewis acid such as BF₃, ZnCl₂, or SnCl₄ complexed with ether or amine. This article explores the resulting adhesives as a function of the epoxy monomer functionality, concentration, solubility in the acrylic monomer, Lewis acid catalyst concentration, phase crosslinking, and postprocessing thermal history. The adhesive morphology exhibits a finely dispersed epoxy phase strongly interacting with the major acrylic phase resulting from a nucleation‐and‐growth phase‐separation mechanism. Excellent adhesion to plastics, including polyethylene, polypropylene, poly(tetrafluoroethylene), poly(ethylene terephthalate), and nylon, is achieved with a much higher thermal performance than that achievable with acrylic polymers alone. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 989–998, 2007     

Effect of end‐tethered polymers on surface adhesion of glassy polymers

The adhesion between a glassy polymer melt and substrate is studied in the presence of end‐grafted chains chemically attached to the substrate surface. Extensive molecular dynamics simulations have been carried out to study the effect of the areal density ∑ of tethered chains and tensile pull velocity v on the adhesive failure mechanisms. The initial configurations are generated using a double‐bridging algorithm in which new bonds are formed across a pair of monomers equidistant from their respective free ends. This generates new chain configurations that are substantially different than the original two chains such that the systems can be equilibrated in a reasonable amount of cpu time. At the slowest tensile pull velocity studied, a crossover from chain scission to crazing is observed as the coverage increases, while for very large pull velocity, only chain scission is observed. As the coverage increases, the sections of the tethered chains pulled out from the interface form the fibrils of a craze that are strong enough to suppress chain scission, resulting in cohesive rather than adhesive failure. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 199–208, 2004     

Synthetic adhesive attachment discs inspired by spider's pyriform silk architecture

Spiders attach their major ampullate silk dragline fibers to surfaces using attachment discs spun from pyriform silk fibers. These attachment discs allow spiders to move safely from place to place while secured to a dragline and to attach their webs to a variety of surfaces. Here, we demonstrate a simple electrospinning process to mimic the “staple‐pin” architecture used by spiders for these attachment discs. Experimental and theoretical evidence are provided to confirm the advantages of thousands of micron‐size “staple‐pins” and their low peeling angles to enhance the adhesive forces required to peel the natural and synthetic attachment discs. These results provide a unique architectural design for fabricating new adhesives that uses very little material for various biomedical and material science applications. © 2014 Wiley Periodicals, Inc. J Polym Sci Part B: Polym. Phys. 2014 , 52, 553–560     

Synthesis and characterization of polycyanurates as dismantlable adhesives

Random copolycyanurates with a low number of amide units in the main chain have been developed as a candidate of dismantlable adhesives based on the rapid decrease of the molecular weights during the rearrangement to polyisocyanurates by a thermal treatment. The random copolycyanurates were prepared by the phase‐transfer‐catalyzed polycondensation of 2,4‐dichloro‐6‐methoxy‐1,3,5‐triazine with bisphenol A and a new bisphenol containing an amide unit in the presence of tetrabutylammonium bromide. They exhibited an excellent adhesive property for the silicon and copper deposited on the silicon substrate after the high thermal treatment of 240 °C under 0.6 MPa compression, and the die shear strengths of these polymers dramatically decreased at 260 °C for 1 h. Random copolycyanurates containing the amide unit are shown to be promising materials for dismantlable adhesion. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1153–1158     

Recent approaches in designing bioadhesive materials inspired by mussel adhesive protein

Marine mussels secret protein‐based adhesives, which enable them to anchor to various surfaces in a saline, intertidal zone. Mussel foot proteins (Mfps) contain a large abundance of a unique, catecholic amino acid, Dopa, in their protein sequences. Catechol offers robust and durable adhesion to various substrate surfaces and contributes to the curing of the adhesive plaques. In this article, we review the unique features and the key functionalities of Mfps, catechol chemistry, and strategies for preparing catechol‐functionalized polymers. Specifically, we reviewed recent findings on the contributions of various features of Mfps on interfacial binding, which include coacervate formation, surface drying properties, control of the oxidation state of catechol, among other features. We also summarized recent developments in designing advanced biomimetic materials including coacervate‐forming adhesives, mechanically improved nano‐ and micro‐composite adhesive hydrogels, as well as smart and self‐healing materials. Finally, we review the applications of catechol‐functionalized materials for the use as biomedical adhesives, therapeutic applications, and antifouling coatings. © 2016 The Authors. Journal of Polymer Science Part A: Polymer Chemistry Published by Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 9–33     

Synthesis and properties evaluation of quaternized polyurethanes as antibacterial adhesives

We present new side‐chain quaternized polyurethanes as antibacterial adhesives made by polyaddition polymerization followed by quaternization for different time intervals. The degree of quaternization of N‐diol units in the polymer is changed from 13.6 to 99.0 mol % (almost complete) for tuning the antibacterial action (leaching/contact type) and studying effect on adhesive strength. The degree of quaternization of about 26 mol % provided the nonleaching antibacterial effect with adhesive strength more than 60 N cm^?2 on aluminum and glass substrates. The increase in the degree of quaternization enhanced polymer polarity shifting nonleaching (contact type) antibacterial behavior to the leaching type but maintaining the high adhesive strengths. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 752–757     

Effect of nonlinear viscoelastic properties on tack

The influence of rheological and surface properties on adhesive tackiness are studied. In particular, the importance of the elongational properties is emphasized in a model, which considers only the adhesive contribution while neglecting the importance of cavitation and surface roughness. This simple analysis allows us to recover the different types of curves (i.e., different adhesive materials) obtained in the literature on tack. Elastic, strain‐hardening, and viscous adhesive materials are considered. The question of the importance of surface properties is raised and discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3139–3149, 2003     

Viscoelasticity and tack of poly(vinyl pyrrolidone)–poly(ethylene glycol) blends

The adhesive properties of blends of high molecular weight poly(vinyl pyrrolidone) (PVP) and low molecular weight poly(ethylene glycol) (PEG) were systematically investigated with a probe test and correlated with their viscoelastic properties. The material parameters that were varied were the PEG content (31–41 wt %) and the hydration rate. The 36% PEG showed the best balance of properties for a pressure‐sensitive adhesive. At low debonding rates, the debonding took place through the formation of a fibrillar structure, whereas at high debonding rates, the debonding was brittle. This transition was attributed to the breakage and reformation of hydrogen bonds between PVP units and OH groups on PEG during the large strain of the polymer chains in elongation. This transition was observed, albeit shifted in frequency, for all three compositions, and the characteristic relaxation times of the hydrogen‐bonded network were estimated. A comparison between the tack properties of the adhesives and their linear viscoelastic properties showed a very strong decoupling between the small‐strain and large‐strain properties of the adhesive, which was indicative of a pronounced deviation from rubber elasticity in the behavior of the blends. This deviation, also seen during tensile tests, was attributed to the peculiar phase behavior of the blends. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2395–2409, 2002     

Synthesis of lightly crosslinked zwitterionic polymer‐based bioinspired adhesives for intestinal tissue sealing

In this report, we have developed a new bioinspired medical adhesive capable of providing a leak‐proof barrier for application to intestinal anastomoses. The newly synthesized adhesive is a terpolymer possessing three different repeating units: (1) A zwitterionic polymer, poly(sulfobetaine methacrylate) (polySBMA), for increased hydrophilicity and biocompatibility, (2) a 3,4‐dihydroxy‐L‐phenylalanine (DOPA) segment which contains the catechol group, and (3) poly(ethylene glycol) dimethacrylate (PEGDMA) for light crosslinking, which will be used to strengthen the polymer adhesion properties by providing debonding resistance. The chemical structure of the terpolymer, poly(N‐methacryloyl‐3,4‐dihydroxyl‐L‐phenylalanine‐co‐sulfobetaine methacrylate‐co‐poly(ethylene glycol) dimethacrylate) (poly(MDOPA‐co‐SBMA‐co‐PEGDMA)), synthesized following a convenient and reproducible radical polymerization was clearly confirmed by ¹H NMR. The terpolymer adhesive displayed the optimal adhesion properties when containing 1.5–2.5 mol % of crosslinker, PEGDMA, according to the measured maximum adhesion strength and work of adhesion, characterized by lap shear strength tests utilizing porcine skin. The adhesive did not show cytotoxicity when tested with human embryonic kidney (HEK293A) cells. Ex vivo anastomosis experiments using porcine intestine demonstrated that the new poly(MDOPA‐co‐SBMA‐co‐PEGDMA) is a promising biomedical adhesive which successfully prevents leakage from the sutured intestinal tissue. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1564–1573     

Iodonium sulfonates as high‐performance coinitiators and additives for CQ‐based systems: Toward aromatic amine‐free photoinitiating systems

Iodonium sulfonates are proposed here as a new class of high‐performance coinitiators for camphorquinone (CQ)‐based systems for the polymerization of methacrylates under blue light irradiation. When combined with CQ, the new proposed coinitiators present excellent polymerization performances and are excellent candidates for the replacement of tertiary aromatic amines subjected to toxicological concerns in the well‐established CQ/amine photoinitiating system (PIS). Remarkably, good bleaching properties are obtained after polymerization. The use of the new PIS for dental adhesives is also investigated. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1664–1669     

Effect of the structure of latex particles on adhesion. Part I: Synthesis and characterization of structured latex particles of acrylic copolymers and their peel adhesion behavior

This is a series of articles that deals with fundamental aspects of the effects of the structure of latex particles of acrylic copolymers on their adhesion behavior. Specifically, relationship or analogy between rheological properties and adhesion performance of the acrylic copolymers was demonstrated. The first part of this series concerns the synthesis and characterization of latex particles with desired structures and compositions, and the experimental results of peel adhesion. The second part develops an analogy between the peel adhesion performance of the adhesives and rheological properties of the corresponding copolymers. The third part addresses the generalities and particularities of three major tests for adhesion: peeling, blistering, and spontaneous peeling. Three types of structured latex particles were synthesized by three different emulsion polymerization processes: the first type had a uniform composition over the entire particles with a glass transition temperature (T_g) varying between ?40°C and 0°C, depending upon the compositions of monomers involved in the copolymer; the second type was of core-shell structure. As for the third type, the composition of monomers varied gradually across the particle radii. The glass transition behavior and the dynamic mechanical properties in the solid state of the copolymers confirmed the structures of the corresponding latex particles. On the other hand, the peel adhesion performance of the films of these latex particles varied with the dynamic mechanical properties of the corresponding copolymers. This implies that a correlation could be found between the structure of the latex particles, dynamic mechanical properties in the solid state of the corresponding copolymers, and the peel adhesion performance of the adhesive films. ©1995 John Wiley & Sons, Inc.     

Synthesis of novel moisture‐curable polyurethanes end‐capped with trialkoxysilane and their application to one‐component adhesives

Novel silane endcappers and novel polyurethanes end‐capped with trimethoxysilane (silylated polyurethanes) were developed as water‐curable materials in which the curing reaction occurred under humid conditions in the presence of dioctyltin diversatate as a curing catalyst. A variety of amine‐terminated trimethoxysilane compounds were synthesized by the Michael addition reaction of commercially available 3‐aminopropyltrimethoxysilane with acrylates, and the resulting silane endcappers were used to react with isocyanate‐terminated polyurethanes, providing the silylated polyurethanes. The moisture‐curable silylated polyurethanes were used for the preparation of novel one‐component and solvent‐free adhesives. The evaluated properties were the curing speed, the tensile shear bond strength, and the adherence to some substrates. The longer alkyl chains of the silane endcappers derived from various acrylates led to a slower curing speed, lower tensile strength at break, and longer elongation at break of the silylated polyurethanes. The tensile shear bond strength of the silylated polyurethane‐based adhesive decreased with decreasing the trimethoxysilane end‐capping ratio, whereas an increase in the adherence was observed. The adherence to the acrylic substrate was improved by changes in the main‐chain structure of the polyurethane based on the composition of poly(propylene oxide) and poly(ethylene oxide). © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2689–2704, 2007     

Fracture behavior of triglyceride‐based adhesives

The use of natural plant oils in the production of adhesives has been the focus of much research because natural oils are a renewable resource which have environmental and economic advantages over the petroleum‐derived chemicals used in traditional adhesives. The network formation and the stress–strain behavior of these plant oil–based adhesives is studied using a combination of simulation techniques. An off‐lattice Monte Carlo simulation has been developed to model the formation of these networks via the free‐radical copolymerization of the triglycerides present in natural oils. Networks of systems representing the triglycerides found in soybean oil, linseed oil, and olive oil are generated, as are networks made from other “theoretical” natural oils. The structure of the networks is characterized by percolation analysis. The stress–strain behavior of these networks is studied using large‐scale molecular dynamics simulations. Tensile strains are applied to the networks and it is observed that with increasing n the failure stress increases but the failure strain decreases. Also, for systems with low values of n, large voids form while the system is strained and then the system fails cohesively. However, for large n, no significant voiding is observed and the system fails close to the interface. The simulation results are shown to be consistent with the vector percolation theoretical prediction for how the failure stress relates to n. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3333–3343, 2004     

New polymer‐chemical developments in clinical dental polymer materials: Enamel–dentin adhesives and restorative composites

In the past 10 years, many new components were synthesized and evaluated for an application in enamel–dentin adhesives and direct composite restoratives. New bisacrylamide cross‐linkers with improved hydrolytic stability and new strongly acidic polymerizable phosphonic acids and dihydrogen phosphates, as well as novel photoinitator systems, in combination with the implementation of novel application devices, have significantly improved the performance of the current enamel–dentin adhesives. The currently used resins for direct composite restoratives are mainly based on methacrylate chemistry to this day. A continuous improvement of the properties of current composites was achieved with the use of new tailor‐made methacrylate cross‐linkers, new additives, and photoinitiators as well as tailor‐made fillers. Nowadays, dental adhesives and methacrylate‐based direct restorative materials have found wide‐spread acceptance. Nevertheless, future developments in the field of dental adhesives and direct composite restoratives will focus on improving durability and biocompatibility as well as the development of materials with a broader application spectrum and of smart adhesives or composites. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Teflon hierarchical nanopillars with dry and wet adhesive properties

The superior material properties of β‐keratin along with the hierarchical high‐aspect‐ratio structure of geckos' foot pad have enabled geckos to stick readily and rapidly to almost any surfaces in both dry and wet conditions. In this research, nonsticky fluoropolymer (Teflon AF) resembling β‐keratin rigidity and having an extremely low surface energy and dielectric constant was applied to fabricate a novel dry adhesive consisting of high‐aspect‐ratio nanopillars terminated with a “fluffy” top layer. Both the nanopillars and the terminating layer are fabricated concurrently by replica molding using a nanoporous anodic aluminum oxide membrane as the mold. These Teflon AF hierarchical nanostructures are shown to have an exceptional capacity to generate strong adhesion in both dry conditions and under water because of combined actions of van der Waals forces, electrostatic attractions, and hydrophobic effects. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012