Phase behavior,crystallization, and morphology in thermosetting blends of a biodegradable poly(ethylene glycol)‐type epoxy resin and poly(ϵ‐caprolactone)

Thermosetting blends of a biodegradable poly(ethylene glycol)‐type epoxy resin (PEG‐ER) and poly(?‐caprolactone) (PCL) were prepared via an in situ curing reaction of poly(ethylene glycol) diglycidyl ether (PEGDGE) and maleic anhydride (MAH) in the presence of PCL. The miscibility, phase behavior, crystallization, and morphology of these blends were investigated. The uncured PCL/PEGDGE blends were miscible, mainly because of the entropic contribution, as the molecular weight of PEGDGE was very low. The crystallization and melting behavior of both PCL and the poly(ethylene glycol) (PEG) segment of PEGDGE were less affected in the uncured PCL/PEGDGE blends because of the very close glass‐transition temperatures of PCL and PEGDGE. However, the cured PCL/PEG‐ER blends were immiscible and exhibited two separate glass transitions, as revealed by differential scanning calorimetry and dynamic mechanical analysis. There existed two phases in the cured PCL/PEG‐ER blends, that is, a PCL‐rich phase and a PEG‐ER crosslinked phase composed of an MAH‐cured PEGDGE network. The crystallization of PCL was slightly enhanced in the cured blends because of the phase‐separated nature; meanwhile, the PEG segment was highly restricted in the crosslinked network and was noncrystallizable in the cured blends. The phase structure and morphology of the cured PCL/PEG‐ER blends were examined with scanning electron microscopy; a variety of phase morphologies were observed that depended on the blend composition. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2833–2843, 2004     

Epoxy resin/poly(ϵ‐caprolactone) blends cured with 2,2‐bis[4‐(4‐aminophenoxy)phenyl]propane. I. Miscibility and crystallization kinetics

Crystalline thermosetting blends composed of 2,2′‐bis[4‐(4‐aminophenoxy)phenyl]propane (BAPP)‐cured epoxy resin (ER) and poly(?‐caprolactone) (PCL) were prepared via the in situ curing reaction of epoxy monomers in the presence of PCL, which started from initially homogeneous mixtures of diglycidyl ether of bisphenol A (DGEBA), BAPP, and PCL. The miscibility of the blends after and before the curing reaction was established with differential scanning calorimetry and dynamic mechanical analysis. Single and composition‐dependent glass‐transition temperatures (T_g's) were observed in the entire blend composition after and before the crosslinking reaction. The experimental T_g's were in good agreement with the prediction by the Fox and Gordon–Taylor equations. The curing reaction caused a considerable increase in the overall crystallization rate and dramatically influenced the mechanism of nucleation and the growth of the PCL crystals. The equilibrium melting point depression was observed for the blends. An analysis of the kinetic data according to the Hoffman–Lauritzen crystallization kinetic theory showed that with an increasing amorphous content, the surface energy of the extremity surfaces increased dramatically for DGEBA/PCL blends but decreased for ER/PCL blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1085–1098, 2003     

Fractionated crystallization of α‐ and β‐nucleated polypropylene droplets

A layer multiplying coextrusion process was used to produce multilayered polypropylene/polystyrene (PP/PS) films with various nucleating agents. When heated into the melt, the thin PP layers broke up into submicron PP droplets that exhibited fractionated crystallization. If the initial PP layers were 20 nm or less, the resulting droplets exhibited exclusively homogeneous nucleation. If a nucleating agent was added, the systematic departure from homogeneous nucleation provided insight into the nature of the heterogeneous nucleation. In this study, we used thermal analysis, atomic force microscopy (AFM), and wide angle X‐Ray scattering (WAXS) to examine the effect of two nucleating agents. We confirmed with WAXS and AFM that a soluble sorbitol nucleating agent for the PP α‐form operates in three concentration regimes as proposed in a previous study. Morphologically, homogeneous nucleation of the submicron droplets produced a granular texture. The correlation length from small‐angle X‐Ray scattering (SAXS) suggested that the grains contained 1–3 mesophase domains. Drawing on classical nucleation theory, the critical size nucleus of an individual mesophase domain was estimated to be about 2 nm³, which was considerably smaller than the mesophase domain. This pointed to mesophase crystallization that included the processes of nucleation and growth. Additional experiments were performed with nucleating agents for the PP β‐form. However, they were not effective in nucleating crystallization of the droplets, presumably because they were essentially insoluble in PP and the nucleating particles were too large to be accommodated in the PP droplets. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Epoxy resin/poly(ϵ‐caprolactone) blends cured with 2,2‐bis[4‐(4‐aminophenoxy)phenyl]propane. II. Studies by Fourier transform infrared and carbon‐13 cross‐polarization/magic‐angle spinning nuclear magnetic resonance spectroscopy

Crystalline thermosetting blends composed of 2,2′‐bis[4‐(4‐aminophenoxy)phenyl]propane‐crosslinked epoxy resin (ER) and poly(?‐caprolactone) (PCL) were investigated by means of Fourier transform infrared (FTIR) spectroscopy and high‐resolution solid‐state NMR spectroscopy. FTIR investigations indicated that there were specific intermolecular interactions between ER and PCL and that the intermolecular hydrogen‐bonding interactions were weaker than the self‐association in pure epoxy. The intermolecular hydrogen bonding was considered to be the driving force for the miscibility of the thermosetting blends. For the examination of the miscibility of the thermosetting blends at the molecular level, high‐resolution solid‐state ¹³C cross‐polarity/magic‐angle spinning (CP‐MAS) NMR spectroscopy was employed. The line width of ¹³C CP‐MAS spectra decreased with increasing PCL contents, and the chemical shift of the carbonyl carbon resonance of PCL shifted to a low field with an increasing epoxy content in the blends. The proton spin–lattice relaxation experiments in the laboratory frame showed that all the blends possessed identical, composition‐dependent relaxation times (i.e., the proton spin–lattice relaxation times in the laboratory frame), suggesting that the thermosetting blends were homogeneous on the scale of 20–30 nm in terms of the spin‐diffusion mechanism, and this was in a good agreement with the results of differential scanning calorimetry and dynamic mechanical analysis. For the examination of the miscibility of the blends at the molecular level, the behavior of the proton lattice relaxation in the rotating frame was investigated. The homogeneity of the thermosetting blends at the molecular level was quite dependent on the blend composition. The PCL‐lean ER/PCL blends (e.g., 70/30) displayed a single homogeneous amorphous phase, and the molecular chains were intimately mixed on the segmental scale. The PCL‐rich blends displayed biexponential decay in experiments concerning the proton spin–lattice relaxation times in the rotating frame, which was ascribed to amorphous and crystalline phases. In the amorphous region, the molecular chains of epoxy and PCL were intimately mixed at the molecular level. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1099–1111, 2003     

Isothermal crystallization kinetics of polypropylene with silane functionalized multi‐walled carbon nanotubes

Multi‐walled carbon nanotubes (MWNTs) were functionalized with a silane coupling agent. The MWNTs were first coated with inorganic silica by a sol‐gel process and then grafted with 3‐methacryloxypropyltrimethoxysilane (3‐MPTS). The effect of raw MWNTs and silane‐functionalized MWNTs on the crystallization behavior of poly(propylene) (PP) was investigated by means of polarized optical microscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. Results obtained from isothermal crystallization experiments indicate that 3‐MPTS functionalization affects the crystallization and melting behavior of PP/MWNTs composites remarkably, which can be attributed to the fact that 3‐MPTS functionalization of MWNTs leads to a uniform dispersion of MWNTs in PP matrix resulting in the good nucleating effect of MWNTs. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1616–1624, 2007     

Crystallization and morphology of poly(ethylene‐2,6‐naphthalene dicarboxylate) in the presence of nucleating agents

The crystallization and morphology of poly(ethylene‐2,6‐naphthalene dicarboxylate) (PEN) containing, as nucleating agents, a sodium salt of a copolymer of ethylene and acrylic acid or a sodium salt of a copolymer of ethylene and methacrylic acid, were investigated with differential scanning calorimetry, polarized optical microscopy, and small‐angle light scattering. The nucleating agents accelerated the crystallization rate at high temperatures by decreasing the surface free energy barrier hindering nucleation. Meanwhile, the nucleating agents with flexible chains could also improve the mobility of the PEN chains and increase the crystallization rate at low temperatures. Hedrites were observed when PEN was crystallized at high temperatures, whereas crystallization at low temperatures led to the formation of spherulites. Similar but smaller morphologies were obtained in the presence of nucleating agents. With nucleating agents, the spherulites formed at low temperatures were less perfect, although the optical properties of the spherulites were not influenced. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2387–2394, 2002     

Study of hydrogen‐bonding strength in poly(ϵ‐caprolactone) blends by DSC and FTIR

The hydrogen‐bonding strength of poly(?‐caprolactone) (PCL) blends with three different well‐known hydrogen‐bonding donor polymers [i.e., phenolic, poly(vinyl‐phenol) (PVPh), and phenoxy] was investigated with differential scanning calorimetry and Fourier transform infrared spectroscopy. All blends exhibited a single glass‐transition temperature with differential scanning calorimetry, which is characteristic of a miscible system. The strength of interassociation depended on the hydrogen‐bonding donor group in the order phenolic/PCL > PVPh/PCL > phenoxy/PCL, which corresponds to the q value of the Kwei equation. In addition, the interaction energy density parameter calculated from the melting depression of PCL with the Nishi–Wang equation resulted in a similar trend in terms of the hydrogen‐bonding strength. Quantitative analyses on the fraction of hydrogen‐bonded carbonyl groups in the molten state were made with Fourier transform infrared spectroscopy for all systems, and good correlations between thermal behaviors and infrared results were observed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1348–1359, 2001     

Crystallization kinetics and crystalline morphology of poly(ε-caprolactone) in blends with grafted rubber particles

The crystallization behavior of pure PCL and PCL in blends with crosslinked rubber particles was studied under (non)isothermal crystallization conditions, where the rubber particles were grafted with PCL chains via hydrogen abstraction of the aliphatic moieties in PCL. The crystal growth and the organization of crystals into spherulitic superstructures are significantly influenced by the presence of the grafted rubber particles, which act as an excellent nucleating agent for PCL. The nucleating efficiency shows an exponential dependency on the PCL grafting density and, according to an Avrami analysis, an increased PCL grafting density increases the overall crystallization rate of the PCL matrix. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1438–1448, 2010     

Nucleation,Crystallization, and Thermal Fractionation of Poly (ε‐Caprolactone)‐Grafted‐Lignin: Effects of Grafted Chains Length and Lignin Content

Poly(ε‐caprolactone)‐grafted‐lignin (PCL‐g‐lignin) copolymers with 2 to 37 wt % lignin are employed to study the effect of lignin on the morphology, nucleation, and crystallization kinetics of PCL. Lignin displays a nucleating action on PCL chains originating an intersecting lamellar morphology. Lignin is an excellent nucleating agent for PCL at low contents (2–5 wt %) with nucleation efficiency values that are close to or >100%. This nucleating effect increases the crystallization and melting temperature of PCL under nonisothermal conditions and accelerates the overall isothermal crystallization rate of PCL. At lignin contents >18 wt %, antinucleation effects appear, that decrease crystallization and melting temperatures, reduce crystallinity degree, hinder annealing during thermal fractionation and significantly retard isothermal crystallization kinetics. The results can be explained by a competition between nucleating effects and intermolecular interactions caused by hydrogen bonding between PCL and lignin building blocks. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1736–1750     

Influence of organic modifiers on morphology and crystallization of poly(ϵ‐caprolactone)/synthetic clay intercalated nanocomposites

ε‐caprolactone was polymerized in the presence of neat montmorillonite or organomontmorillonites to obtain a variety of poly(ε‐caprolactone) (PCL)‐based systems loaded with 10 wt % of the silicates. The materials were thoroughly investigated by different X‐ray scattering techniques to determine factors affecting structure of the systems. For one of the nanocomposites it was found that varying the temperature in the range corresponding to crystallization of PCL causes reversible changes in the interlayer distance of the organoclay. Extensive experimental and literature studies on this phenomenon provided clues indicating that this effect might be a result of two‐dimensional ordering of PCL chains inside the galleries of the silicate. Small angle X‐ray scattering and wide angle X‐ray scattering investigation of filaments oriented above melting point of PCL revealed that polymer lamellae were oriented perpendicularly to particles of unmodified silicate, while in PCL/organoclay systems they were found parallel to clay tactoids. Calorimetric and microscopic studies shown that clay particles are effective nucleating agents. In the nanocomposites, PCL crystallized 20‐fold faster than in the neat polymer. The crystallization rate in nanocomposites was also significantly higher than in microcomposite. Further research provided an insight how the presence of the filler affects crystalline fraction and spherulitic structure of the polymer matrix in the investigated systems. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2350–2367, 2007     

Isothermal crystallization behaviors of isotactic polypropylene nucleated with α/β compounding nucleating agents

Sodium 2,2′‐methylene‐bis(4,6‐di‐tert‐butylphenyl) phosphate (NA40) and N,N‐dicyclohexylterephthalamide (NABW) are high effective nucleating agents for inducing the formation of α‐isotactic polypropylene (α‐iPP) and β‐iPP, respectively. The isothermal crystallization kinetics of iPP nucleated with nucleating agents NABW, NA40/NABW (weight ratio of NA40 to NABW is 1:1) and NA40 were investigated by differential scanning calorimetry (DSC) and Avrami equation was adopted to analyze the experimental data. The results show that the addition of NABW, NA40/NABW and NA40 can shorten crystallization half‐time (t_1/2) and increase crystallization rate of iPP greatly. In these three nucleating agents, the α nucleating agent NA40 can shorten t_1/2 of iPP by the largest extent, which indicates that it has the best nucleation effect. While iPP nucleated with NA40/NABW compounding nucleating agents has shorter t_1/2 than iPP nucleated with NABW. The Avrami exponents of iPP and nucleated iPP are close to 3.0, which indicates that the addition of nucleating agents doesn't change the crystallization growth patterns of iPP under isothermal conditions and the crystal growth is heterogeneous three‐dimensional spherulitic growth. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 590–596, 2007     

Study on the β to α transformation of polypropylene crystals in compatibilized blend of polypropylene/polyamide‐6

By using a commercial β‐nucleating agent (TMB‐5) for polypropylene (PP), it was observed that high β‐crystal content in a compatibilized blend of polypropylene/polyamide‐6 (labeled as Blend‐03 in this work) can be achieved for samples prepared by compression moulding. As β‐PP possesses more superior impact strength then α‐PP, and the β to α transformation is an important mechanism of energy absorption for β‐PP, it is of obvious interest to understand the possibilities of β to α transformation in β‐polypropylene/polyamide‐6 blends. Tensile tests were performed at temperatures of 20, 30, 40, and 50 °C, and the occurrence of β to α transformation was monitored by differential scanning calorimeter and wide angle X‐ray diffraction measurements. It was observed that the β to α transformation in Blend‐03 could only be activated at elevated tensile testing temperatures. This was related to the increase in tensile elongation at break with the increase in tensile testing temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2674–2681, 2007     

Crystallization behavior of dynamically cured polypropylene/epoxy blends

Dynamically cured polypropylene (PP)/epoxy blends compatibilized with maleic anhydride grafted PP were prepared by the curing of an epoxy resin during melt mixing with molten PP. The morphology and crystallization behavior of dynamically cured PP/epoxy blends were studied with scanning electron microscopy, differential scanning calorimetry, and polarized optical microscopy. Dynamically cured PP/epoxy blends, with the structure of epoxy particles finely dispersed in the PP matrix, were obtained, and the average diameter of the particles slightly increased with increasing epoxy resin content. In a study of the nonisothermal crystallization of PP and PP/epoxy blends, crystallization parameter analysis showed that epoxy particles could act as effective nucleating agents, accelerating the crystallization of the PP component in the PP/epoxy blends. The isothermal crystallization kinetics of PP and dynamically cured PP/epoxy blends were described by the Avrami equation. The results showed that the Avrami exponent of PP in the blends was higher than that of PP, and the crystallization rate was faster than that of PP. However, the crystallization rate decreased when the epoxy resin content was greater than 20 wt %. The crystallization thermodynamics of PP and dynamically cured PP/epoxy blends were studied according to the Hoffman theory. The chain folding energy for PP crystallization in dynamically cured PP/epoxy blends decreased with increasing epoxy resin content, and the minimum of the chain folding energy was observed at a 20 wt % epoxy resin content. The size of the PP spherulites in the blends was obviously smaller than that of PP. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1181–1191, 2004     

Effects of nucleating agents on microstructure and fracture toughness of poly(propylene)/ethylene‐propylene‐diene terpolymer blends

The effects of nucleating agents (NAs) on fracture toughness of injection‐molded isotactic poly(propylene)/ethylene‐propylene‐diene terpolymer (PP/EPDM) were studied in this work. Compared with PP/EPDM blends without any NA, PP/EPDM/NA blends show very small and homogeneous PP spherulites. As we expected, PP/EPDM blends nucleated with β‐phase NA aryl amides compound (TMB‐5) present not only a significant enhancement in toughness but also a promotion of brittle‐ductile transition. However, the addition of α‐phase NA 1,3:2,4‐bis(3,4‐dimethylbenzylidene) sorbitol (DMDBS) has no apparent effect on the toughness of the blends. The impact‐fractured surface morphologies of such samples were analyzed via scanning electronic microscope (SEM). More detail work about the toughening mechanisms of elastomer and NA based on elastomer particles size and matrix crystal structures were carried out. Our results suggest that, besides the crystal structures of matrix, the elastomer particles size and size distribution plays an important role in controlling the toughening effect of nucleated PP/elastomer blends. The smaller the elastomer particles size and lower the polydispersity, the more apparent the synergistic toughening effect of NA and elastomer is. This investigation provides a fresh insight into the understanding of toughening mechanism of elastomers in PP blends and facilitates to the design of super toughened PP materials. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 46–59, 2009     

Thermal behavior and intermolecular interactions in blends of poly(3‐hydroxybutyrate) and maleated poly(3‐hydroxybutyrate) with chitosan

The thermal behavior and intermolecular interactions of blends of poly(3‐hydroxybutyrate) (PHB) and maleated PHB with chitosan were studied with differential scanning calorimetry, Fourier transform infrared (FTIR), wide‐angle X‐ray diffraction (WAXD), and X‐ray photoelectron spectroscopy (XPS). The differences in the two blend systems with respect to their thermal behavior and intermolecular interactions were investigated. The melting temperatures, melting enthalpies, and crystallinities of the two blend systems gradually decreased as the chitosan content in the blends increased. Compared with that of the PHB component with the same composition, the crystallization of the maleated PHB component was more intensively suppressed by the chitosan component in the blends because of the rigid chitosan molecular chains and the intermolecular hydrogen bonds between the components. FTIR, WAXD, and XPS showed that the intermolecular hydrogen bonds in the blends were caused by the carbonyls of PHB or maleated PHB and chitosan aminos, and their existence depended on the compositions of the blends. The introduction of maleic anhydride groups onto PHB chains promoted intermolecular interactions between the maleated PHB and chitosan components. In addition, the intermolecular interactions disturbed the original crystal structures of the PHB, maleated PHB, and chitosan components; this was further proven by WAXD results. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 35–47, 2005     

Effect of a sorbitol nucleating agent on fractionated crystallization of polypropylene droplets

The effect of a sorbitol nucleating agent on crystallization of polypropylene (PP) in droplets was studied. Layer‐multiplying coextrusion was used to fabricate assemblies of 257 layers, in which PP nanolayers alternated with thicker polystyrene (PS) layers. The concentration of a commercial nucleating agent, Millad 3988 (MD) in the layers was varied up to 2 wt %. When the assembly was heated into the melt, interfacial driven breakup of the 12 nm PP layers produced a dispersion of submicron PP particles in a PS matrix. Analysis of optical microscope images and atomic force microscope images indicated that the particle size was not affected by the presence of MD. The crystallization behavior of the particle dispersion was characterized by thermal analysis. In the absence of a nucleating agent, the submicron particles crystallized almost exclusively by homogeneous nucleation at about 40 °C. Addition of a nucleating agent to the PP layers offered a unique opportunity to study the nature of heterogeneous nucleation. Nucleation by MD resulted in fractionated crystallization of the submicron PP particles. The concentration dependence of the multiple crystallization exotherms was interpreted in terms of the binary polypropylene‐sorbitol phase diagram. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1788–1797, 2007     

Effect of poly(vinyl alcohol) fine particles as a novel biodegradable nucleating agent on the crystallization of poly(3‐hydroxybutyrate)

The effect of poly(vinyl alcohol)(PVA) fine particles as the nucleating agent on the crystallization behavior of bacterial poly(3‐hydroxybutyrate)(PHB) was studied using differential scanning calorimetry measurements and polarized light microscope observation. The results were compared with the effect of PVA conventionally blended with PHB. The PVA fine particles were found to be able to greatly enhance the crystallization of PHB, while the conventionally blended PVA extremely retarded the crystallization of PHB. The nucleating effect of PVA fine particles is almost comparable to that of the talc powder. Considering the biodegradability and biocompatibility of PVA, the usage of PVA particle as a nucleating agent provides marked benefits over the currently employed nonbiodegradable nucleating agents, such as talc and boron nitride. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44:1813–1820, 2006     

Characterization of electron beam irradiation blends based on metallocene ethylene‐1‐octene copolymer

Binary blends using metallocene ethylene‐1‐octene copolymer as matrix were prepared and subjected to electron beam (EB) irradiation (50, 100, and 200 kGy). Gel content and melt flow index values indicated that the blends were crosslinking. Fourier transform infrared‐ATR spectroscopy was used to study the crosslinking and oxidative degradation of the blends via tertiary carbon and carboxyl group formation, respectively. Thermal and mechanical properties were studied showing that the crystallinity of both matrix and dispersed phase decreased with irradiation dose, and that the thermoplastic elastomers with good mechanical properties may be obtained by EB irradiation. Chain branching and scission were also detected at all irradiation doses, although at the highest doses (200 kGy) a crosslinking reaction was the most predominantly observed effect. The successive self‐nucleation annealing technique was used to determine the EB irradiation effects on crystallization of some blends in which crosslinking and chain branching take place, modifying the chain's structure and therefore crystalline regions in the matrix and the dispersed phase. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2432–2440, 2007     

Formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber blends: Effects of preparation method,composition, and thermal condition

The effects of preparation method, composition, and thermal condition on formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber (iPP/EPR) blends were studied using modulated differential scanning calorimeter (MDSC), wide angle X‐ray diffraction (WAXD), and phase contrast microscopy (PCM). It was found that the α‐iPP and β‐iPP can simultaneity form in the melt‐blended samples, whereas only α‐iPP exists in the solution‐blended samples. The results show that the formation of β‐iPP in the melt‐blended samples is related to the crystallization temperature and the β‐iPP generally diminishes and finally vanishes when the crystallization temperature moves far from 125 °C. The phenomena that the lower critical temperature of β‐iPP in iPP/EPR obviously increases to 114 °C and the upper critical temperature decreases to 134 °C indicate the narrowing of temperature interval, facilitating the formation of β‐iPP in iPP/EPR. Furthermore, it was found that the amount of β‐iPP in melt‐blended iPP/EPR samples is dependent on the composition and the maximum amount of β‐iPP formed when the composition of iPP/EPR blends is 85:15 in weight. The results through examining the effect of annealing for iPP/EPR samples at melt state indicate that this annealing may eliminate the susceptibility to β‐crystallization of iPP. However, only α‐iPP can be observed in solution‐blended samples subjected to annealing for different time. The PCM images demonstrate that an obvious phase‐separation happens in both melt‐blended and solution‐blended iPP/EPR samples, implying that compared with the disperse degree of EPR in iPP, the preparation method plays a dominant role in formation of β‐iPP. It is suggested that the origin of formation of β‐iPP results from the thermomechanical history of the EPR component in iPP/EPR. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1704–1712, 2007     

Comparison of different nucleating agents on crystallization of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerates)

In this study, thymine and melamine were introduced as nucleating agents for poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerates) (PHBVs) and poly(3‐hydroxybutyrate) (PHB), and their effects were compared with that of boron nitride (BN). Because the overall crystallization rate of PHBVs decreases significantly with the increase in the 3‐hydroxyvalerate comonomer content, the study focused on the crystallization of PHBVs. Isothermal crystallization kinetics of the neat PHBVs and the nucleated PHBVs were studied by differential scanning calorimetry (DSC). The Avrami equation was derived and the parameters were assessed for the nucleation and crystal growth mechanism. The nucleation and crystal growth were examined using polarized optical microscopy. All nucleating agents had similar particle sizes and showed good dispersion in the polymer matrix, as revealed by scanning electron microscopy. The results indicated that BN and thymine significantly increased the overall crystallization rate for all PHBVs studied and demonstrated very similar nucleating effects. Melamine reacted with PHBVs and accelerated the thermal degradation, and hence was less effective in nucleating PHBVs. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1564–1577, 2007