Effects of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] on the charge distributions of low‐density polyethylene/polystyrene blends

The effect of the triblock copolymer poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) on the formation of the space charge of immiscible low‐density polyethylene (LDPE)/polystyrene (PS) blends was investigated. Blends of 70/30 (wt %) LDPE/PS were prepared through melt blending in an internal mixer at a blend temperature of 220 °C. The amount of charge that accumulated in the 70% LDPE/30% PS blends decreased when the SEBS content increased up to 10 wt %. For compatibilized and uncompatibilized blends, no significant change in the degree of crystallinity of LDPE in the blends was observed, and so the effect of crystallization on the space charge distribution could be excluded. Morphological observations showed that the addition of SEBS resulted in a domain size reduction of the dispersed PS phase and better interfacial adhesion between the LDPE and PS phases. The location of SEBS at a domain interface enabled charges to migrate from one phase to the other via the domain interface and, therefore, resulted in a significant decrease in the amount of space charge for the LDPE/PS blends with SEBS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2813–2820, 2004     

Tailoring of interface of polypropylene/polystyrene/carbon nanofibre composites by polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene

Mechanical and physical properties of polypropylene (PP)/polystyrene (PS) blend, PP/PS/polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS) ternary blend and their composites with carbon nanofibers (CNF) were investigated. Composites of ternary blend exhibited superior properties compared to those of binary blends. Mechanical performance of nanocomposites was intimately related to their phase morphology. PP/PS/SEBS/0.1 wt% CNF hybrid composites exhibited excellent impact strength (Four-fold increase compared to PP/PS blend) and ductility (12-fold increase in elongation at break, with respect to PP/PS blend). Moreover, these composites displayed good tensile strength and modulus (15% increase in Young's modulus, compared to PP/PS/SEBS blend) and are suitable for various end-use applications including automobile applications. Although crystallinity of PP phase is decreased by the incorporation of CNF, thermal stability of the composites remained almost unaffected. Contact angle measurements revealed that ternary composites exhibited maximum hydrophobicity.     

Compatibilizing effect of functionalized polystyrene blends: a study of morphology,thermal, and mechanical properties

Polystyrene (PS), being an amorphous polymer is immiscible with other polymers. To engender miscible blends, PS has been functionalized with an active amino‐functional group on the molecular chains of PS to yield amino‐substituted polystyrene (APS), which serves as a reactive compatibilizer. The compatibilization effect of amino functionalized polystyrene on the rubber toughening was explored and results were compared in terms of morphology, thermal, and mechanical properties of PS/SEBS‐g‐MA versus APS/SEBS‐g‐MA blends. In addition, the effect of rubber content on the blend morphology and mechanical properties were investigated. An appreciable change in the thermal stability of APS blends in comparison with PS blend has been probed. A marked correlation has been observed between phase morphology and thermal stability. Use of APS produced the compatibilized blends which render improved blend morphology, enhanced thermal and mechanical properties. Optimal thermal, morphological and mechanical profiles were depicted by 20‐wt% APS blend. Copyright © 2008 John Wiley & Sons, Ltd.     

Mechanical properties and characteristic of surface treated bamboo fiber reinforced PP/PS blends

Bamboo fiber (BF) as organic filler is characterized by mechanical properties analysis and morphology examination for polypropylene (PP) and polystyrene (PS) matrix blends. Effects of different filler content on tensile strength, flexural properties, and impact strength are proposed. It is observed from scanning electron microscopy (SEM) studies that addition of BF is beneficial in increasing mechanical strength via increasing the interface dispersed phase. The optimum tensile properties and impact properties of BF content were at 40 wt% for PP/PS/BF composite on melt mixing conditions. The results showed a significant improvement in mechanical properties of PP/PS/BF ternary blend composite. Comparing with untreated BF, content of carbon and nitrogen of treated BF decreased to 66.57 and 2.31%, oxygen content increased to 21.07%, and silicon content increased from 0 to 10.04%. The element ratio of O/C, N/C, and Si/C changed to 31.65, 3.47, and 15.08, respectively.     

Stabilization of a cocontinuous phase morphology by a tapered diblock or triblock copolymer in polystyrene‐rich low‐density polyethylene/polystyrene blends

The stability against the thermal annealing of a cocontinuous two‐phase morphology developed in polystyrene (PS)/low‐density polyethylene (LDPE) blends containing 80 wt % PS was investigated. Blends containing 1, 5, and 10 wt % of a tapered diblock poly(styrene‐block‐hydrogenated butadiene) (P(S‐b‐hB)) or triblock poly(styrene‐block‐hydrogenated butadiene‐block‐styrene) (P(S‐hB‐S)) copolymer were melt‐blended with roll‐mill mixing equipment. The efficiency of each of the two copolymers in stabilizing against coalescence the cocontinuous morphology was examined. The tensile properties of the resulting blends, annealed and nonannealed, were also examined in relation to the morphology induced by thermal annealing. The phase morphology was studied by optical and scanning electron microscopy. With computer‐aided image analysis, it was possible to obtain a measurable characteristic parameter to quantify the cocontinuous phase morphology. When it was necessary, the extraction of one phase with a selective solvent was performed. Although the observed differences were subtle, the tapered diblock exhibited a more efficient compatibilizing activity than the triblock copolymer, particularly at a low concentration of about 2 wt %. The superiority of the tapered diblock over the triblock might be due to its ability to quantitatively locate at the LDPE/PS interface and consequently form a more efficient barrier against the subsequent breakup of the elongated structures of the cocontinuous phase morphology. The tensile properties of the triblock‐modified blends were more sensitive to thermal annealing than the tapered‐modified ones. This deficiency was ascribed to the phase morphology coarsening of the dispersed polyethylene phase. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 202–216, 2003     

Mechanical properties of polymer‐blend nanocomposites with organoclays: Polystyrene/ABS and high impact polystyrene/ABS

Thirty‐three polystyrene (PS)/acrylonitrile‐butadiene‐styrene (ABS) and high impact PS/ABS polymer blends with organoclay and copolymer additives were prepared by melt processing using different mixing sequences in order to test the putative capability of clay to perform a compatibilizing role in polymer blends. In general, the addition of clay increased the tensile modulus and had little effect on tensile strength. For the blends studied in this work, the addition of organoclays caused a catastrophic reduction in impact strength, a critical property for commercial viability. The polymer‐blend nanocomposites adopted a structure similar to that for ABS/clay nanocomposites as determined by X‐ray diffraction and transmission electron microscopy. It is suggested that clay reinforcement inhibits energy absorption by craze formation and shear yielding at high strain rates. Simultaneous mixing of the three components provided nanocomposites with superior elongation and energy to failure compared to sequential mixing. The clay pre‐treated with a benzyl‐containing surfactant gave the best overall properties among the various organoclays tested and of the two clay contents studied 4 wt % was preferred over 8 wt % addition. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Evaluation of the SEBS copolymer in the compatibility of PP/ABS blends through mechanical,thermal, thermomechanical properties,and morphology

Polypropylene (PP) blends with acrylonitrile-butadiene-styrene (ABS) were prepared using the styrene-ethylene-butylene-styrene copolymer (SEBS) as a compatibilizing agent. The blends were prepared in a co-rotational twin-screw extruder and injection molded. Torque rheometry, Izod impact strength, tensile strength, heat deflection temperature (HDT), differential scanning calorimetry, thermogravimetry, and scanning electron microscopy properties were investigated. The results showed that there was an increase in the torque of PA6/ABS blends with SEBS addition. The PP/ABS/SEBS (60/25/15%) blend showed significant improvement in impact strength, elongation at break, thermal stability, and HDT compared with neat PP. The elastic modulus and tensile strength have not been significantly reduced. The degree of crystallinity and the crystalline melting temperature increased, indicating a nucleating effect of ABS. The PP/ABS blends compatibilized with 12.5% and 15% SEBS presented morphology with well-distributed fine ABS particles with good interfacial adhesion. As a result, thermal stability has been improved over pure PP and the mechanical properties have been increased, especially impact strength. In general, the addition of the SEBS copolymer as the PP/ABS blend compatibilizer has the advantage of refining the blend's morphology, increasing its toughness and thermal stability, without jeopardizing other PP properties.     

PPO/SEBS-g-MAH共混体系的形态结构与冲击性能

从亚微相态和冲击性能出发 ,对比了采用熔融挤出法制备的PPO/SEBS和PPO/SEBS g MAH两种共混物 .结果表明 ,在本文所研究的弹性体用量范围内 ,PPO/SEBS为“海 岛”型结构 ,而PPO/SEBS g MAH呈现网状结构 ;PPO/SEBS体系无脆韧转变现象 ,PPO/SEBS g MAH体系则在弹性体用量为 10 %～ 15 %时出现明显的脆韧转变 ,缺口冲击强度达到 95 0J/m ,这种超韧现象源于其网状结构的形成 .文中进一步用DSC和毛细管流变仪对共混体系的热性能和流变性能进行了测试 ,探讨了PPO/SEBS g MAH共混物网状结构的形成原因     

Influence of extender oil composition on flowing property,thermal stability,and morphology of styrene‐b‐ethylene‐co‐butylene‐b‐styrene copolymer/polypropylene/oil blends

In this study, a series of styrene‐b‐ethylene‐co‐butylene‐b‐styrene copolymer (SEBS)/polypropylene (PP)/oil blends with different kinds of oil composition was developed through melt blending. The effect of oil with different composition and properties on its phase equilibrium and “redistribution” in multiphasic SEBS elastomer was systematically studied for the first time. Moreover, an integral influencing mechanism of oil composition on the structure and properties of SEBS/PP/oil blends was also put forward. The mineral oil was mainly distributed in ethylene/butylene (EB)/PP phase, which greatly enhanced the processing flowability of SEBS/PP/oil blends. With increasing oil C_N content, a redistribution of oil appeared and excess naphthenic oil (NO) entered the interphase of soft and hard phases. The dynamic mechanical thermal analysis (DMTA) analysis indicated that the polystyrene (PS) phase was plasticized, which also helped to improve the processing fluidity of blends. However, the plasticizing of physical cross‐linking point PS resulted in a decrease in mechanical strength and thermal stability. Small‐angle X‐ray scattering (SAXS) and transmission electron microscope (TEM) results showed that PS phase (45 nm to 55 nm) cylindrically distributed in EB/PP/oil matrix, the excess NO in the interphase enlarged the distance between PS phase and widen the escape channel for oil migration. At over 45% oil C_N content, the electron density difference between soft and hard phases reduced to the minimum, same as T_gPS, indicating a deeper plasticizing effect. The PS phase swelled and exhibited elastic behavior; thus, the force could be uniformly transferred between two phases. Importantly, a recover in strength and thermal stability was observed in O‐5 blend. This work significantly filled the gap of studies in oil‐extended thermoplastic elastomers (TPEs), exhibiting great theoretical guiding significance and application value.     

含二烯丙基双酚A醚相容剂对HDPE/PC共混体系的影响

用低密度聚乙烯接枝二烯丙基双酚Ａ醚（ＬＤＰＥ ｇ ＤＢＡＥ）作为高密度聚乙烯／聚碳酸酯（ＨＤＰＥ／ＰＣ）共混体系的增容剂,研究了其对ＨＤＰＥ／ＰＣ共混体系的影响．通过共混物形态观察、热力学性能测试和结晶性分析,发现ＬＤＰＥ ｇ ＤＢＡＥ对ＨＤＰＥ／ＰＣ共混体系有良好的增容效果．并发现了增容剂在共混物中的最佳用量为１０ｐｈｒ,提高增容剂的接枝率更有利于改善共混物的性能     

Long-Range Processing Correlation and Morphological Fractality of Compatibilized Blends of PS/ HDPE/ SEBS Block Copolymer

Summary: Processing and compatibilization effects of a commercially available styrene/ ethylene-butylene/ styrene (SEBS) compatibilizer on the morphological structure, rheological and mechanical properties of blends of polystyrene (PS) and high density polyethylene (HDPE) were investigated. The rheological behaviour of the blends melt during processing was followed by measuring torque; extrusion capacity output and melts back-pressure in a twin screw extruder. The processing parameters were decreased with the HDPE content. The results show that SEBS compatibilizer can yield compatibilization by substantially reducing torque and increasing the back-pressure. However, the Hurst indices of melt processing parameters are increased with compatibilization. Near-infrared spectra had been described by the Hurst index H_NIR which is then related to HDPE content in the blends. The correlation between the blend compositions, morphological structure, mechanical and rheological properties and processing parameters was established and discussed on base of correlation with the fractal indices obtained from the SEM microphotographs of PS/HDPE/SEBS blends.     

Effects of elastomer on morphology,flammability and rheological properties of HIPS/PS‐encapsulated Mg(OH)2 composites

The effects of elastomer type on morphology, flammability and rheological properties of high‐impact polystyrene/Mg(OH)₂ based on encapsulated by polystyrene have been investigated. The ternary composites characterized by cone calorimetry, horizontal burning rate, limiting oxygen index (LOI), rheology and SEM. Morphology was controlled using poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] triblock copolymer (SEBS) or the corresponding maleinated SEBS (SEBS‐g‐MA). As revealed by SEM observations, composites of HIPS/SEBS/Mg(OH)₂ exhibit separation of the filler and elastomer and good adhesion between SEBS and the filler, whereas composites of HIPS/SEBS‐g‐MA/Mg(OH)₂ exhibit encapsulation of the filler by SEBS‐g‐MA. The flame retardant and rheological properties of ternary composites were strongly dependent on microstructure. The rheological test showed that the composites with encapsulation structure exhibit a stronger solid‐like response at low frequency than those of the composites with separate dispersion structure. The combustion tests showed that the composites with encapsulation structure showed higher flame retardant properties than those of separate dispersion structure at optimum use level of SEBS‐g‐MA. However, with the increase of the content of SEBS‐g‐MA, the flame retardancy of the composite declined somewhat which can be explained that the SEBS‐g‐MA coating acts as a heat and mass transfer barrier due to the formation of encapsulation structure. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2023–2030, 2007     

Impact‐modified polypropylene/vermiculite nanocomposites

Impact‐modified polypropylene (PP)/vermiculite (VMT) nanocomposites toughened with maleated styrene–ethylene butylene–styrene (SEBS‐g‐MA) were compounded in a twin‐screw extruder and injection‐molded. VMT was treated with maleic anhydride, which acted both as a compatibilizer for the polymeric matrices and as a swelling agent for VMT in the nanocomposites. The effects of the impact modifier on the morphology and the impact, static, and dynamic mechanical properties of the PP/VMT nanocomposites were investigated. Transmission electron microscopy revealed that an exfoliated VMT silicate layer structure was formed in ternary (PP–SEBS‐g‐MA)/VMT nanocomposites. Tensile tests showed that the styrene–ethylene butylene–styrene additions improved the tensile ductility of the (PP–SEBS‐g‐MA)/VMT ternary nanocomposites at the expense of their tensile stiffness and strength. Moreover, Izod impact measurements indicated that the SEBS‐g‐MA addition led to a significant improvement in the impact strength of the nanocomposites. The SEBS‐g‐MA elastomer was found to be very effective at converting brittle PP/VMT organoclay composites into tough nanocomposites. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2332–2341, 2003     

Transport properties of thermoplastic/thermoset blends

Gas transport properties are reported for two series of films prepared from initially miscible thermoplastic/thermoset blends, respectively, polystyrene PS/thermoset and poly(2,6 dimethyl 1,4 phenylene oxide) PPE/thermoset blends. The thermoplastic contents are such that in both cases, after the phase separation, the continuous phase is the thermoplastic‐rich phase and scanning electron microscopic photomicrographs clearly evidenced the dispersion of thermoset‐rich nodules in the continuous thermoplastic‐rich phase with a more tortuous morphology in the case of PPE based films. Permeability measurements were made for O₂ and CO₂ at 20°C and a reduction in permeability coefficients was observed with increased thermoset content. Analysis using Maxwell law suggests that for all thermoplastic/thermoset blends, the thermoset particles can be considered as impermeable to gas and that the diffusion takes place in the continuous phase. In the case of PPE based films, the higher decrease of permeability than that predicted by the law has been related to the morphology of the blends and thus the tortuosity and to a partial miscibility of the thermoset in the thermoplastic. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 473–483, 1999     

Effect of mixing conditions on the morphology and properties of polystyrene/polyethylene blends compatibilized with styrene–butadiene block copolymers

The effect of mixing conditions on the morphology, molten‐state viscoelastic properties, and tensile impact strength of polystyrene/polyethylene (80/20) blends compatibilized with styrene–butadiene block copolymers containing various numbers and lengths of blocks was studied. Under all mixing conditions, an admixture of a styrene–butadiene block copolymer led to a finer phase structure and to an increase in the dynamic viscosity, storage modulus, and tensile impact strength. The effects were stronger for S–B diblock with a short styrene block than for S–B–S–B–S pentablock with long styrene blocks (where S represents styrene and B represents butadiene). For all blends mixed longer than 2 min, the mixing time had only a small effect on their morphology and properties. Surprisingly, the localization of S–B diblock copolymers was strongly dependent on the rate of mixing. The mixing rate had a nonnegligible effect on the viscoelastic properties of the compatibilized blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 609–622, 2003     

Polypropylene/montmorillonite nanocomposites toughened with SEBS‐g‐MA: Structure–property relationship

Polypropylene (PP)/organo‐montmorillonite (Org‐MMT) nanocomposites toughened with maleated styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MA) were prepared via melt compounding. The structure, mechanical properties, and dynamic mechanical properties of PP/SEBS‐g‐MA blends and their nanocomposites were investigated by X‐ray diffraction (XRD), polarizing optical microscopy (POM), tensile, and impact tests. XRD traces showed that Org‐MMT promoted the formation of β‐phase PP. The degree of crystallinity of PP/SEBS‐g‐MA blends and their nanocomposites were determined from the wide angle X‐ray diffraction via profile fitting method. POM experiments revealed that Org‐MMT particles served as nucleating sites, resulting in a decrease of the spherulite size. The essential work of fracture approach was used to evaluate the tensile fracture toughness of the nanocomposites toughened with elastomer. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3112–3126, 2005     

A METHOD TO QUANTIFY CRAZING DEFORMATION BY TENSILE TESTS FOR POLYSTYRENE/POLYOLEFIN ELASTOMER IMMISCIBLE BLENDS

A method to quantify crazing deformations by tensile tests for polystyrene （PS） and polyolefin elastomer （POE） blends was investigated. The toughness of PS/POE blends, reflected by the Charpy impact strength, increased with the content of POE. SEM micrographs showed the poor compatibility between PS and POE. In simple tensile tests, it is very easy to achieve the ratio of crazing deformation, i.e. K by measuring the size changes of samples. The K values decreased with increasing the content of POE, and the deformations of PS/POE blends were dominated by crazing. The plots of the change of volume （△V） against longitudinal variation （△I） showed a linear relationship, and the slope of lines decreased with the content of POE. Measuring samples at the tensile velocities of 5 mm/min, 50 mm/min, and 500 mm/min respectively, the K values kept unchanged for each PS/POE blends.     

Effects of polystyrene‐b‐poly(ethylene/propylene)‐b‐polystyrene compatibilizer on the recycled polypropylene and recycled high‐impact polystyrene blends

The recycled polypropylene/recycled high‐impact polystyrene (R‐PP/R‐HIPS) blends were melt extruded by twin‐screw extruder and produced by injection molding machine. The effects of polystyrene‐b‐poly(ethylene/propylene)‐b‐polystyrene copolymer (SEPS) used as compatibilizer on the mechanical properties, morphology, melt flow index, equilibrium torque, and glass transition temperature (T_g) of the blends were investigated. It was found that the notch impact strength and the elongation at break of the R‐PP/R‐HIPS blends with the addition of 10 wt% SEPS were 6.46 kJ/m² and 31.96%, which were significantly improved by 162.46% and 57.06%, respectively, than that of the uncompatibilized blends. Moreover, the addition of SEPS had a negligible effect on the tensile strength of the R‐PP/R‐HIPS blends. Additionally, the morphology of the blends demonstrated improved distribution and decreased size of the dispersed R‐HIPS phase with increasing the SEPS content. The increase of the melt flow index and the equilibrium torque indicated that the viscosity of the blends increased when the SEPS was incorporated into the R‐PP/R‐HIPS blends. The dynamic mechanical properties test showed that when the content of SEPS was 10 wt%, the difference of T_g decreased from 91.72°C to 81.51°C. The results obtained by differential scanning calorimetry were similar to those measured by dynamic mechanical properties, indicating an improved compatibility of the blends with the addition of SEPS.     

Impact fracture toughness of polyamide‐6/montmorillonite nanocomposites toughened with a maleated styrene/ethylene butylene/styrene elastomer

Polyamide‐6 (PA6)/montmorillonite (MMT) nanocomposites toughened with maleated styrene/ethylene butylene/styrene (SEBS‐g‐MA) were prepared via melt compounding. Before melt intercalation, MMT was treated with an organic surfactant agent. Tensile and impact tests revealed that the PA6/4% MMT nanocomposite fractured in a brittle mode. The effects of SEBS‐g‐MA addition on the static tensile and impact properties of PA6/4% MMT were investigated. The results showed that the SEBS‐g‐MA addition improved the tensile ductility and impact strength of the PA6/4% MMT nanocomposite at the expenses of its tensile strength and stiffness. Accordingly, elastomer toughening represents an attractive route to novel characteristics for brittle clay‐reinforced polymer nanocomposites. The essential work of fracture (EWF) approach under impact drop‐weight conditions was used to evaluate the impact fracture toughness of nanocomposites toughened with an elastomer. Impact EWF measurements indicated that the SEBS‐g‐MA addition increased the fracture toughness of the PA6/4% MMT nanocomposite. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 585–595, 2005     

PS/SBS/CaCO_3共混物体系脆韧转变

研究了不同组成的聚苯乙烯 (PS)基三元共混物体系的缺口冲击性能、拉伸性能和断面形貌以及相形态 .实验结果表明 ,微米级碳酸钙的增韧改性效果稍好于纳米级碳酸钙 ,但增强效果却相反 .随着分散相含量的增加 ,3种共混物韧性皆明显提高 ,拉伸曲线向右下方移动 ,应变软化减弱 ,应变硬化增强 .研究发现了随分散相含量的增加 ,PS共混物出现了脆韧转变 ,而且脆韧转变以不同的形式表现了出来 ,即冲击强度、断面形貌以及拉伸曲线在同一区间同时出现了转变