Synthesis of poly(vinylidene fluoride)‐b‐poly(styrene sulfonate) block copolymers by controlled radical polymerizations

Block copolymers based on poly(vinylidene fluoride), PVDF, and a series of poly(aromatic sulfonate) sequences were synthesized from controlled radical polymerizations (CRPs). According to the aromatic monomers, appropriate techniques of CRP were chosen: either iodine transfer polymerization (ITP) or atom transfer radical polymerization (ATRP) from PVDF‐I macromolecular chain transfer agents (CTAs) or PVDF‐CCl₃ macroinitiator, respectively. These precursors were produced either by ITP of VDF with C₆F₁₃I or by radical telomerization of VDF with chloroform, respectively. Poly(vinylidene fluoride)‐b‐poly(sodium styrene sulfonate), PVDF‐b‐PSSS, block copolymers were produced from both techniques via a direct polymerization of sodium styrene sulfonate (SSS) monomer or an indirect way with the use of styrene sulfonate ethyl ester (SSE) as a protected monomer. Although the reaction led to block copolymers, the kinetics of ITP of SSS showed that PVDF‐I macromolecular CTAs were not totally efficient because a limitation of the CTA consumption (56%) was observed. This was probably explained by both the low activity of the CTA (that contained inefficient PVDF‐CF₂CH₂? I) and a fast propagation rate of the monomer. That behavior was also noted in the ITP of SSE. On the other hand, ATRP of SSS initiated by PVDF‐CCl₃ was more controlled up to 50% of conversion leading to PVDF‐b‐PSSS block copolymer with an average number molar mass of 6000 g·mol^?1. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of proton‐conducting block copolymer membranes composed of a fluorinated segment and a sulfonic acid segment

Diblock copolymer membranes having a fluorinated segment and a sulfonic acid segment were prepared by living radical polymerization, solution casting, and crosslinking, followed by heat treatment. Diblock copolymers of 2,3,4,5,6‐pentafluorostyrene (PFS)/4‐(1‐methylsilacyclobutyl)styrene (SBS) and neopentyl styrenesulfonate (SSPen) (poly(PFS‐co‐SBS)‐b‐polySSPen)s were synthesized by nitoroxy‐mediated living radical polymerization. Self‐standing crosslinked membranes were obtained by casting a THF solution of the block copolymer with Pt catalyst. Heat treatment of the membrane at 230 °C induced decomposition of the neopentyl sulfonate esters to provide block copolymer membranes having a fluorinated segment and a free sulfonic acid segment. It was confirmed that the block copolymer with a high sulfonic acid content exhibited high ion exchange capacity and high proton conductivity as well as high thermal stability. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4479–4485, 2008     

Synthesis and self‐assembly of amphiphilic macrocyclic block copolymer topologies

We demonstrated the synthesis of miktoarm star block copolymers of AB, AB₂, and A₂B, in which block A consisted of linear poly(tert‐butyl acrylate) (P^tBA) and block B consisted of cyclic polystyrene. These structures were produced using the atom transfer radical polymerization to make telechelic polymers that, after modification, were further coupled together by copper‐catalyzed “click” reactions with high coupling efficiency. Deprotection of P^tBA to poly(acrylic acid) (PAA) afforded amphiphilic miktoarm structures that when micellized in water gave vesicle morphologies when the block length of PAA was 21 units. Increasing the PAA block length to 46 units produced spherical core‐shell micelles. AB₂ miktoarm stars packed more densely into the core compared to its linear counterpart (i.e., a four times greater aggregation number with approximately the same hydrodynamic diameter), resulting in the PAA arms being more compressed in the corona and extending into the water phase beyond its normal Gaussian chain conformation. These results show that the cyclic structure attached to an amphiphilic block has a significant influence on increasing the aggregation number through a greater packing density. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

UV‐induced crosslinking of ring opening metathesis block copolymer micelles

Statistical and amphiphilic block copolymers bearing cinnamoyl groups were prepared by ring opening metathesis polymerization (ROMP). The UV‐induced [2 + 2] cycloaddition reaction of polymer bound cinnamic acid groups was studied in polymer thin films as well as in block copolymer micelles. In both cases, exposure to UV‐light for 10 min led to a crosslinking conversion of about 60%, as determined by FT‐IR spectroscopy and UV–vis absorption measurements. Time based IR‐spectroscopy revealed a maximum conversion of 78% reached after an irradiation time of about 16 min. For micelles obtained from polymers bearing 5 mol % or more cinnamoyl groups, the crosslinking reaction proceeded smoothly, yielding in crosslinked particles which were stable in a non‐selective solvent (CHCl₃). Diameters determined by dynamic light scattering in the selective solvent (MeOH) were similar for both, non‐crosslinked and crosslinked micelles, whereas diameters of crosslinked micelles in the non‐selective solvent (CHCl₃) were significantly larger compared to MeOH samples. This strategy of direct self assembly of block‐copolymers in a selective solvent followed by “clean” crosslinking, without the need for additional crosslinking reagents or crosslinking initiators, provides a straight forward approach toward ROMP‐based polymeric nano‐particles. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2402–2413, 2008     

Synthesis of core‐crosslinked carbosilane block copolymer micelles and their thermal transformation to silicon‐based ceramics nanoparticles

Carbosilane fine particles were synthesized by core‐crosslinking of carbosilane block copolymer micelles and they were pyrolytically transformed into silica nanoparticles. The carbosilane block copolymer, poly(1‐(3‐butenyl)‐1‐methylsilacyclobutane)‐block‐polystyrene, (polyBMSB‐b‐polySt), [(m, n) = (31, 16), (54, 30), and (75, 28)], was synthesized by anionic polymerization of BMSB and St, where m and n represent polymerization degrees of BMSB and St segments, respectively. The block copolymer formed micelles in N,N‐dimethylformamide (DMF). The hydrodynamic diameters (D_h) of the micelles evaluated by dynamic light scattering ranged from 40 to 158 nm depending on the copolymer molecular weight. The core of the micelle was cross‐linked by Pt‐catalyzed hydrosilation with 1,2‐bis(dimethylsilylethane). The D_h of the core‐cross‐linked micelles in THF ranged from 56 to 164 nm. These precursor particles were pyrolyzed at 850 °C under N₂ to give ceramic nanoparticles. The diameters of the spherical ceramic particles estimated by AFM ranged from 25 to 60 nm. X‐ray fluorescence analysis of the ceramic products revealed that it consisted of mainly SiO₂ rather than SiC. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3778–3787, 2005     

Amphiphilic diblock,triblock, and star block copolymers by living radical polymerization: Synthesis and aggregation behavior

Copper(I)‐mediated living radical polymerization was used to synthesize amphiphilic block copolymers of poly(n‐butyl methacrylate) [P(n‐BMA)] and poly[(2‐dimethylamino)ethyl methacrylate] (PDMAEMA). Functionalized bromo P(n‐BMA) macroinitiators were prepared from monofunctional, difunctional, and trifunctional initiators: 2‐bromo‐2‐methylpropionic acid 4‐methoxyphenyl ester, 1,4‐(2′‐bromo‐2′‐methyl‐propionate)benzene, and 1,3,5‐(2′‐bromo‐2′‐methylpropionato)benzene. The living nature of the polymerizations involved was investigated in each case, leading to narrow‐polydispersity polymers for which the number‐average molecular weight increased fairly linearly with time with good first‐order kinetics in the monomer. These macroinitiators were subsequently used for the polymerization of (2‐dimethylamino)ethyl methacrylate to obtain well‐defined [P(n‐BMA)_x‐b‐PDMAEMA_y]_z diblock (15,900; polydispersity index = 1.60), triblock (23,200; polydispersity index = 1.24), and star block copolymers (50,700; polydispersity index = 1.46). Amphiphilic block copolymers contained between 60 and 80 mol % hydrophilic PDMAEMA blocks to solubilize them in water. The polymers were quaternized with methyl iodide to render them even more hydrophilic. The aggregation behavior of these copolymers was investigated with fluorescence spectroscopy and dynamic light scattering. For blocks of similar comonomer compositions, the apparent critical aggregation concentration (cac = 3.22–7.13 × 10^?3 g L^?1) and the aggregate size (ca. 65 nm) were both dependent on the copolymer architecture. However, for the same copolymer structure, increasing the hydrophilic PDMAEMA block length had little effect on the cac but resulted in a change in the aggregate size. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 439–450, 2002; DOI 10.1002/pola.10122     

Synthesis and characterizations of the four‐armed amphiphilic block copolymer S[poly(2,3‐dihydroxypropyl acrylate)‐block‐poly(methyl acrylate)]4

The polymers poly[(2,2‐dimethyl‐1,3‐dioxolane‐4yl) methyl acrylate] (PDMDMA) and four‐armed PDMDMA with well‐defined structures were prepared by the polymerization of (2,2‐dimethyl‐1,3‐dioxolane‐4yl) methyl acrylate (DMDMA) in the presence of an atom transfer radical polymerization (ATRP) initiator system. The successive hydrolyses of the polymers obtained produced the corresponding water‐soluble polymers poly(2,3‐dihydroxypropyl acrylate) (PDHPA) and four‐armed PDHPA. The controllable features for the ATRP of DMDMA were studied with kinetic measurements, gel permeation chromatography (GPC), and NMR data. With the macroinitiators PDMDMA–Br and four‐armed PDMDMA–Br in combination with CuBr and 2,2′‐bipyridine, the block polymerizations of methyl acrylate (MA) with PDMDMA were carried out to afford the AB diblock copolymer PDMDMA‐b‐MA and the four‐armed block copolymer S{poly[(2,2‐dimethyl‐1,3‐dioxolane‐4yl) methyl acrylate]‐block‐poly(methyl acrylate)}₄, respectively. The block copolymers were hydrolyzed in an acidic aqueous solution, and the amphiphilic diblock and four‐armed block copolymers poly(2,3‐dihydroxypropyl acrylate)‐block‐poly(methyl acrylate) were prepared successfully. The structures of these block copolymers were verified with NMR and GPC measurements. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3062–3072, 2001     

Formation of thermo‐sensitive and cross‐linkable micelles by self‐assembly of poly(pentafluorophenyl acrylate)‐containing block copolymer

Poly(pentafluorophenyl acrylate)‐block‐poly(N‐isopropylacrylamide) (PPFPA‐b‐PNIPAM) is synthesized by reversible addition‐fragmentation chain transfer (RAFT) polymerization. Light‐responsive moieties of ortho‐nitrobenzyl (ONB)‐protected diamine are partially introduced to the PFPA moieties via postpolymerization modification. The amphiphilic block copolymers are assembled into micelles in water. The ONB‐protected diamine group in the micelle core is released upon UV irradiation, which subsequently induces an in situ cross‐linking by a spontaneous reaction with the remaining PFPA groups in the core and yields stable cross‐linked micelles. Micellization of the copolymers is confirmed by dynamic light scattering (DLS) and transmission electron microscopy (TEM). 4‐Nitro‐7‐piperazino‐2,1,3‐benzoxadiazole (NBD) and pyrene are loaded in the core of cross‐linked micelles to demonstrate the possibility for additional post‐functionalization of residual PFPA moieties and hydrophobic molecule encapsulation, respectively. It is anticipated that these micelles can be alternative cargos for incorporating active compounds that may be useful for advanced applications. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1103–1113     

Synthesis of silicon nitride based ceramic nanoparticles by the pyrolysis of silazane block copolymer micelles

Diblock copolymer poly(1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane)‐block‐polystyrene (polyVSA‐b‐polySt) and triblock copolymer poly(1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane)‐block‐polystyrene‐block‐poly(1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane) (polyVSA‐b‐polySt‐b‐polyVSA), consisting of silazane and nonsilazane segments, were prepared by the living anionic polymerization of 1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane and styrene. PolyVSA‐b‐polySt formed micelles having a poly(1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane) (polyVSA) core in N,N‐dimethylformamide, whereas polyVSA‐b‐polySt and polyVSA‐b‐polySt‐b‐polyVSA formed micelles having a polyVSA shell in n‐heptane. The micelles with a polyVSA core were core‐crosslinked by UV irradiation in the presence of diethoxyacetophenone as a photosensitizer, and the micelles with a polyVSA shell were shell‐crosslinked by UV irradiation in the presence of diethoxyacetophenone and 1,6‐hexanedithiol. These crosslinked micelles were pyrolyzed at 600 °C in N₂ to give spherical ceramic particles. The pyrolysis process was examined by thermogravimetry and thermogravimetry/mass spectrometry. The morphologies of the particles were analyzed by atomic force microscopy and transmission electron microscopy. The chemical composition of the pyrolysis products was analyzed by X‐ray fluorescence spectroscopy and Raman scattering spectroscopy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4696–4707, 2006     

Macromolecular surfactants for supercritical carbon dioxide applications: Synthesis and characterization of fluorinated block copolymers prepared by nitroxide‐mediated radical polymerization

Poly(perfluorooctyl‐ethylenoxymethylstyrene) (PFDS) and poly(1,1,2,2‐tetrahydroperfluorodecyl acrylate) (PFDA) homopolymers as well as poly(styrene)‐b‐poly(perfluorooctyl‐ethylenoxymethylstyrene) (PS‐b‐PFDS) and poly(styrene)‐b‐poly(1,1,2,2‐tetrahydroperfluorodecyl acrylate) acrylate) (PS‐b‐PFDA) block copolymers of various chain lengths were synthesized by nitroxide‐mediated radical polymerization in the presence of either 2,2,6,6‐tetramethyl‐1‐piperidinyloxy free radical (TEMPO) in the case of FDS monomer or N‐tert‐butyl‐N‐(1‐diethylphosphono‐2,2‐dimethylpropyl)‐N‐oxyl (DEPN) in the case of the FDA monomer. The molar composition of the block copolymers was determined by elemental analysis and proton NMR while the blocky structure was checked by SEC analysis in trifluorotoluene. Block copolymers PS‐b‐PFDS (3.6K/60K) and PS‐b‐PFDA (3.7K/43K) were soluble in neat CO₂ at moderate pressure and temperature, indicating the formation of micelles. Similar block copolymers with a longer PS block such as PS‐b‐PFDA (9.5K/49K), corresponding to a lower CO₂‐philic/CO₂‐phobic balance, were insoluble in neat CO₂ but could be solubilized in the presence of styrene as a cosolvent. Additionally, surface and bulk properties of PS‐b‐PFDA were investigated, indicating the same surface tension as for the PFDA homopolymer (γ_LV = 10.3 mN/m) and a bulk nanostructured morphology. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3537–3552, 2004     

Facile synthesis of conjugated rod‐coil block copolymers

A facile synthetic approach of conjugated rod‐coil block copolymers with poly(para‐phenylene) as the rod block and polystyrene or polyethylene glycol as the coil block was developed. The block copolymers were synthesized through a TEMPO‐mediated radical polymerization of 3,5‐cyclohexadiene‐1,2‐diol‐derived monomers (diacetate, dibenzonate, and dicarbonate), followed by thermal aromatization of the polymer precursor. The living character of the polymerization and the structure of the copolymers were studied by NMR, GPC, TGA, and UV–vis spectroscopy. The average conjugation lengths of the copolymers were calculated according to their maxima in UV–vis spectroscopy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 800–808, 2007     

Facile fabrication of hybrid nanoparticles surface grafted with multi‐responsive polymer brushes via block copolymer micellization and self‐catalyzed core gelation

Poly(2‐(dimethylamino)ethyl methacrylate)‐b‐poly(γ‐methacryloxypropyl‐trimethoxysilane) (PDMA‐b‐PMPS) was synthesized via consecutive reversible addition‐fragmentation chain transfer (RAFT) polymerizations in 1,4‐dioxane. Subsequent micellization of the obtained amphiphilic diblock polymer in aqueous solution led to the formation of nanoparticles consisting of hydrophobic PMPS cores and well‐solvated PDMA shells. Containing tertiary amine residues, PDMA blocks in micelle coronas can spontaneously catalyze the sol–gel reactions of trimethoxysilyl groups within PMPS cores, leading to the formation of hybrid nanoparticles coated with PDMA brushes. Transmission electron microscopy (TEM) and laser light scattering (LLS) revealed the presence of monodisperse spherical hybrid nanoparticles, and the grafting density of PDMA chains at the surface of nanoparticle cores was estimated to be ～5.8 nm²/chain. PDMA brushes exhibit dual stimuli‐responsiveness, and the swelling/collapse of them can be finely tuned with solution pH and temperatures. The obtained multi‐responsive hybrid nanoparticles might find potential applications in fields such as smart devices, recyclable catalysts, and intelligent nanocarriers for drug delivery or gene transfection. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2379–2389, 2008     

Novel thermo‐responsive self‐assembly micelles from a double brush‐shaped PNIPAM‐g‐(PA‐b‐PEG‐b‐PA)‐g‐PNIPAM block copolymer with PNIPAM polymers as side chains

A novel double brush‐shaped copolymer with amphiphilic polyacrylate‐b‐poly(ethylene glycol)‐b‐poly acrylate copolymer (PA‐b‐PEG‐b‐PA) as a backbone and thermosensitive poly(N‐isopropylacrylamide) (PNIPAM) long side chains at both ends of the PEG was synthesized via an atom transfer radical polymerization (ATRP) route, and the structure was confirmed by FTIR, ¹H NMR, and SEC. The thermosensitive self‐assembly behavior was examined via UV‐vis, TEM, DLS, and surface tension measurements, etc. The self‐assembled micelles, with low critical solution temperatures (LCST) of 34–38 ^°C, form irregular fusiform and/or spherical morphologies with single, double, and petaling cores in aqueous solution at room temperature, while above the LCST the micelles took on more regular and smooth spherical shapes with diameter ranges from 45 to 100 nm. The micelle exhibits high stabilities even in simulated physiological media, with low critical micellization concentration (CMC) up to 5.50, 4.89, and 5.05 mg L^?1 in aqueous solution, pH 1.4 and 7.4 PBS solutions, respectively. The TEM and DLS determination reveled that the copolymer micelle had broad size distribution below its LCST while it produces narrow and homogeneous size above the LCST. The cytotoxicity was investigated by MTT assays to elucidate the application potential of the as‐prepared block polymer brushes as drug controlled release vehicles. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis,characterization, and property of amphiphilic fluorinated abc‐type triblock copolymers

Novel amphiphilic fluorinated ABC‐type triblock copolymers composed of hydrophilic poly(ethylene oxide) monomethyl ether (MeOPEO), hydrophobic polystyrene (PSt), and hydrophobic/lipophobic poly(perfluorohexylethyl acrylate) (PFHEA) were synthesized by atom transfer radical polymerization (ATRP) using N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA)/CuBr as a catalyst system. The bromide‐terminated diblock copolymers poly(ethylene oxide)‐block‐polystyrene (MeOPEO‐b‐PSt‐Br) were prepared by the ATRP of styrene initiated with the macroinitiator MeOPEO‐Br, which was obtained by the esterification of poly(ethylene oxide) monomethyl ether (MeOPEO) with 2‐bromoisobutyryl bromide. A fluorinated block of poly(perfluorohexylethyl acrylate) (PFHEA) was then introduced into the diblock copolymer by a second ATRP process to synthesize a novel ABC‐type triblock copolymer, poly(ethylene oxide)‐block‐polystyrene‐block‐poly(perfluorohexylethyl acrylate) (MeOPEO‐b‐PSt‐b‐PFHEA). These block copolymers were characterized by means of proton nuclear magnetic resonance (¹H NMR) and gel permeation chromatography (GPC). Water contact angle measurements revealed that the polymeric coating of the triblock copolymer (MeOPEO‐b‐PSt‐b‐PFHEA) shows more hydrophobic than that of the corresponding diblock copolymer (MeOPEO‐b‐PSt). Bovine serum albumin (BSA) was used as a model protein to evaluate the protein adsorption property and the triblock copolymer coating posseses excellent protein‐resistant character prior to the corresponding diblock copolymer and polydimethylsiloxane. These amphiphilic fluoropolymers can expect to have potential applications for antifouling coatings and antifouling membranes. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

pH‐responsive destabilization and facile bioconjugation of new hydroxyl‐terminated block copolymer micelles

New hydroxyl‐terminated amphiphilic block copolymers (HO‐ABPs) having pendant t‐butyl groups for pH‐responsiveness and terminal OH groups for bioconjugation are reported. These HO‐ABPs consist of hydrophilic poly(oligo(ethylene oxide) monomethyl ether methacrylate) and hydrophobic poly(t‐butyl methacrylate) blocks and were synthesized by a consecutive atom transfer radical polymerization in the presence of an OH‐terminated bromine initiator. Aqueous self‐assembly of HO‐ABPs resulted in colloidally stable micellar aggregates being capable of encapsulating hydrophobic guest molecules. They were nontoxic to cells and destabilized in response to low pH. A facile bioconjugation of HO‐ABP micelles for active targeting is demonstrated by conjugation with biotin (vitamin H) and competitive assay exhibiting >93% ABP chains conjugated with biotin in each micelle. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis of water‐soluble conductive copolymer based on polyaniline

Synthesis and characterization of polyaniline‐grafted poly(styrene‐alt‐maleic anhydride) (PANI‐g‐PSMA) was carried out to obtain conductive comb copolymers with highly improved processability. First, polyaniline (PANI) was prepared in nano‐scale by chemical synthesis under ultrasonic irradiation. Then the poly(styrene‐alt‐maleic anhydride) (PSMA) was synthesized by free radical polymerization. Moreover, the PANI was grafted on the PSMA backbone to prepare a comb‐like conductive copolymer for improving its processability as a new method. The products were characterized by Fourier transform infrared, ultraviolet–visible spectroscopy and X‐ray diffraction patterns. Morphology of the samples was also investigated by scanning electron microscopy images. Finally, the solubility and conductivity of the products were studied, and it resulted in high solubility of the products in water and other common organic solvents in comparison to the pure PANI. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and characterization of a film‐forming,crosslinked, amphiphilic block copolymer of butadiene and acrylamide

An amphiphilic block copolymer of acrylamide and butadiene was synthesized by the polymerization of acrylamide in the presence of the crosslinker N,N′‐methylene bisacrylamide initiated by a hydroxyl‐terminated polybutadiene/V(V) macroredox initiator. The product had good film‐forming ability. It was characterized by IR and NMR spectroscopy, viscosity, swelling, and microhardness measurements, scanning electron micrography, and differential scanning calorimetry. A good film was obtained from the block copolymer with a greater proportion of butadiene; it had greater permeability for nonpolar solvents, and it was poorly permeable to water and other polar solvents. The film swelled in polar and nonpolar solvents and had almost the same capacity for the loading and release of hydrophilic and hydrophobic dyes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3290–3303, 2006     

Fully biodegradable polymeric micelles based on hydrophobic‐ and hydrophilic‐functionalized poly(lactide) block copolymers

Novel amphiphilic diblock copolymers from a combination of hydrophobic‐functional poly(lactides) (PLAs) with hydrophilic‐functional PLAs or poly(malic acid), respectively, toward fully biodegradable materials for medical applications, such as micellar drug delivery systems, are reported for the first time. The presented PLA‐based polymeric micelles are characterized by their small size below 100 nm, low critical micellar concentrations, good in vitro stabilities at room and body temperature, and efficient incorporation capability of hydrophobic compounds, particularly with regard to potential drug substances. Moreover, the advantage of being totally degradable with different rates at different pH values, as investigated in medical cancer treatment, is demonstrated. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3244–3254, 2010     

Synthesis of amphiphilic star block copolymers via diethyldithiocarbamate‐mediated living radical polymerization

(AB)_f star block copolymers were synthesized by the radical polymerization of a poly(t‐butyl acrylate)‐block‐poly(methyl methacrylate) diblock macroinitiator with ethylene glycol dimethacrylate in methanol under UV irradiation. Diblock macroinitiators were prepared by diethyldithiocarbamate‐mediated sequential living radical copolymerization initiated by (4‐cyano‐4‐diethyldithiocarbamyl)pentanoic acid under UV irradiation. The arm number (f) was controlled by the variation of the initial concentration of the diblock initiator. It was found from light scattering data that such star block copolymers (f ≥ 344) not only took a spherical shape but also formed a single molecule in solution. Subsequently, we derived amphiphilic [arm: poly(acrylic acid)‐block‐poly(methyl methacrylate)] star block copolymers by the hydrolysis of poly(t‐butyl acrylate) blocks. These amphiphilic star block copolymers were soluble in water because the external blocks were composed of hydrophilic poly(acrylic acid) chains. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3321–3327, 2006     

Amphiphilic fluorous random copolymer self‐assembly for encapsulation of a fluorinated agrochemical

Amphiphilic self‐folding random copolymers exhibit different solution behaviors depending on the identity of the hydrophobic/hydrophilic units. Herein, it is demonstrated that changing the hydrophilic unit from poly(ethylene glycol) to the sugar trehalose causes increased discrepancy in the polarity difference with a fluorinated hydrophobic segment and changes the aggregation state of the polymer in water. The PEG‐fluorinated and trehalose/PEG‐fluorinated amphiphilic random copolymers were the most efficient at encapsulating a fluorinated agrochemical. The small‐molecule agrochemical exerts a strong influence on the self‐assembly of the polymers, demonstrating that fluorous interactions result in not only intramolecular self‐folding behavior but also intermolecular polymer association to form well‐defined nanoparticles. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 352–359