Amphiphilic segmented polyurethanes as surface modifying additives

Amphiphilic segmented polyetherurethanes were prepared from methylene diphenylene diisocyanate (MDI), poly(ethylene glycol) 1500 (PEG), and a fatty acid monoglyceride as a chain extender. The polymers were not soluble in water or methanol, but dissolved readily in organic solvents. The amphiphilic properties were demonstrated as a large hysteresis in the water contact angles, exceeding 110°. The amphiphilic polymers were shown to modify the surface properties of a poly(ether urethane) (PEU) and a poly(ether urethane urea) (PEUU) when added in 1–10 wt %, presumably due to migration of the additive to the surface. The surfaces of particularly the PEU blends became highly amphiphilic, exhibiting contact angles hystereses up to 90–100°. A surface saturation effect was observed at 5% added amphiphilic polymer. A difference in the behavior of PEU and PEUU was ascribed to differences in solubility of the additive in the matrix. On long-term exposure to water the PEUU blends increased their amphiphilic behavior.     

The influence of soft segments on some properties of new transparent segmented polyurethanes

This work describes the synthesis and structure of the new segmented polyurethanes (SPURs) formed from an aliphatic diisocyanate [1,1′‐methanediylbis(4‐isocyanatocyclohexane] (Desmodur W^®) and unconventional sulfur‐containing chain extender [2,2′‐methylenebis([4,1‐phenylene]methylenesulfanediyl)diethanol]. Soft segments were poly(oxytetramethylene)diol of  = 1000 g/mol (PTMO) or poly(hexametylene carbonate)diol of  = 860 g/mol (PHCD). For all the polymers, the structure, physicochemical, thermal, and mechanical properties were determined. In addition, for selected polymers, optical properties (refractive index and transparency), adhesive properties, and antimicrobial activity were also determined. The type and amount of soft segment used for the synthesis of SPURs had a significant effect on the properties of the polymers. SPURs from PHCD are characterized by higher glass transition temperatures, molar masses, hardness (up to 91/50°Sh in scale A/D), and tensile strengths (up to 36.5 MPa) but lower elongations at break compared with the SPURs with PTMO. The tests of adhesion and optical properties showed that the PHCD‐based SPUR was characterized by higher value of refractive index, transparency, and more than three times the adhesive strength than the PTMO‐based SPUR. Antimicrobial activity studies showed that the SPUR presence in the medium inhibited proliferation of both Gram‐positive and Gram‐negative bacteria. Copyright © 2017 John Wiley & Sons, Ltd.     

Polyisobutylene‐based polyurethanes. IX. synthesis,characterization, and properties of polyisobutylene‐based poly(urethane‐ureas)

Polyisobutylene (PIB)‐based polyurethanes (PUs) exhibit unparalleled hydrolytic‐oxidative‐biologic stability and are melt processible, however, their mechanical (strength) properties are modest mainly due to insufficient H bonds. We posited and demonstrate that the ultimate properties of PIB‐PUs are enhanced, while their melt processibility is maintained, by the judicious introduction of urea linkages, i.e., strong bifurcated H bonds, in the chain. The incorporation of bifurcated H bonds in PIB‐PUs was achieved by using the conventional butane diol chain extender (CE) in combination with controlled amounts of amino alcohol as co‐chain extender (co‐CE). Polyurethanes containing both urethane and urea linkages are polyurethane‐ureas (PUU). Specifically, PIB‐PUUs prepared with PIB‐diol/MDI together with 80/20 mole % butane diol/amino butanol exhibited ～30 MPa tensile strength, ～550% elongation, ～80 Shore A hardness, and ～137 °C flow temperature. Other amino alcohols, i.e., amino ethanol, ‐propanol, and ‐hexanol, were less effective co‐CEs. ¹H‐NMR and FT‐IR spectroscopies indicate the presence of bifurcated H bonds in PIB‐PUUs prepared with CE/co‐CE combinations. Characterization by differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical thermal analysis, and creep experiments also suggest bifurcated H bonds in PIB‐PUU. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2361–2369     

Young's modulus and loss tangent measurement of polydimethylsiloxane using an optical lever

In this article, the Young's modulus and the loss tangent of polydimethylsiloxane (PDMS) is obtained in the frequency range between 10 and 1500 Hz using an optical technique. The first three mechanical modes of vibrating PDMS beams are detected by measuring the tip rotational displacement using an optical lever. The experiments are carried out for 10:1 and 20:1 volume mixing ratios between the polymer base and the curing agent. The experimental results show that the Young's modulus varies between 1 and 2.6 MPa for 10:1 while its values are between 0.6 and 1.1 MPa for 20:1. The loss tangent is between 0.2 and 0.4 for 10:1 and 0.2 and 0.5 for 20:1. However, the measured values of the loss tangent are greater than the values reported in ref. 13. We also found that if the PDMS is not cured properly, its mechanical properties are time dependent. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 747–751     

Elevation of modulus and elongation of semicrystalline polyurethanes

Polyurethanes were synthesized based on an amorphous polyester polyol, and different chain extenders, comparing the universally accepted symmetric chain extender (1,4‐butanediol) with an asymmetric (1,2‐propanediol) chain extender. The effect of incorporating a crystalline polyester polyol polyhexamethylene adipate (PHMA) was investigated. The resulting morphologies and tensile properties are dramatically different. Based on the thermal and infrared data obtained, the sample with the symmetric chain extender exhibits a phase‐separated morphology, which can change as a function of time and temperature. Conversely, the polyurethane with the asymmetric chain extender has a phase mixed morphology that remains stable under the same experimental conditions. Incorporating crystalline PHMA resulted in a substantial change in the mechanical properties of the materials, especially for the copolymer comprising asymmetric chain extender. The rate of crystallization and the degree of crystallization achieved depended on the type of chain extender used. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018     

Pi‐conjugated chain extenders for the synthesis of optoelectronic segmented polyurethanes

The optical properties of mechanochromic materials change under mechanical stress. Segmented polyurethanes are elastomers composed of amorphous, saturated chain soft segments, and rigid pi‐conjugated hard domains. Within aggregates of hard domains pi–pi interactions may form and result in perturbation of the optoelectronic properties of the system. Disruption and restoration of these electronic interactions within the material may lead to observable mechanochromic response. A series of oligothiophene diols and diamines, as well as a naphthalene diimide diol, have been synthesized for incorporation into the hard domains of segmented polyurethanes and polyureas using long poly(tetramethylene oxide) chains as soft segments. The resulting polymers were evaluated to determine their extent of polymerization and their thermal stability. The optical properties of the materials were studied in solution and as thin films. Where possible the electrochemical properties of the polymers were also explored. The length of the soft segment chains in the segmented polyurethanes hindered electronic coupling of hard domains. Future work involving smaller, more solubilizing soft segments may allow for easier material characterization and mechanochromic response. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Young's modulus of polyethylene in the microstrain region

The stress–strain behavior of various polyethylenes was measured with a strain sensitivity of 2 × 10^?7. Young's modulus was measured as a function of the strain rate. The shapes of the stress–strain curves in the vicinity of room temperature were nonlinear down to the lowest measurable strain. The stress–strain behavior in the microstrain region was well described by the model of the standard linear solid. From the model, the relaxation time was determined along with the relaxed and unrelaxed moduli. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2420–2429, 2001     

Effects of polymerization method on structure and properties of thermoplastic polyurethanes

The effects of the dynamic polymerization method and temperature on the molecular aggregation structure and the mechanical and melting properties of thermoplastic polyurethanes (TPUs) were successfully clarified. TPUs were prepared from poly (ethylene adipate) glycol (M_n = 2074), 4,4′‐diphenylmethane diisocyanate and 1,4‐butanediol by the one‐shot (OS) and the prepolymer (PP) methods in bulk at dynamic polymerization temperatures ranging from 140 to 230 °C. Glass‐transition temperatures (T_gs) of the soft segment and melting points (T_ms) of the hard segment domains of OS‐TPUs increased and decreased, respectively, with increasing polymerization temperatures, but those of PP‐TPUs were almost independent of the polymerization temperature. T_gs of the soft segment and T_ms of the hard segment domains of these TPUs polymerized above 190 °C were almost the same regardless of the polymerization method. Solid‐state nuclear magnetic resonance spectroscopy (NMR) analyses of OS‐ and PP‐TPUs showed that the relative proton content of fast decay components, which corresponds to the hard segment domains, in these TPUs decreased with increasing polymerization temperatures. These results clearly show that the degree of microphase separation becomes weaker with increasing polymerization temperatures. The temperature dependence of dynamic storage modulus and loss tangent of OS‐TPUs coincided with those of PP‐TPUs at polymerization temperature above 190 °C. The apparent shear viscosity for OS‐ and PP‐TPUs polymerized above 190 °C approached a Newtonian behavior at low shear rates regardless of the polymerization method. These results indicate that TPUs polymerized at higher temperatures form almost the same molecular aggregation structures irrespective of the dynamic polymerization method. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 800–814, 2007     

Studies on thermoplastic polyurethanes based on new diphenylethane-derivative diols. II. Synthesis and characterization of segmented polyurethanes from HDI and MDI

Various new thermoplastic segmented polyurethanes were synthesized by a one-step melt polymerization from aliphatic-aromatic α,ω-diols containing sulfur in the aliphatic chain, including 4,4′-(ethane-1,2-diyl)bis(benzenethioethanol), 4,4′-(ethane-1,2-diyl)bis(benzenethiopropanol) and 4,4′-(ethane-1,2-diyl)bis(benzenethiodecanol) as chain extenders, hexane-1,6-diyl diisocyanate (HDI) or 4,4′-diphenylmethane diisocyanate (MDI) and 20-80 mol% poly(oxytetramethylene)diol (PTMO) with molecular weight of 1000 g/mol as a soft segment. The reaction was conducted at the molar ratio of NCO/OH = 1 and 1.05, and in the case of the HDI-based polyurethanes in the presence of dibutyltin dilaurate as a catalyst. The effect of the diisocyanate used on the structure and some physicochemical, thermal and mechanical properties of the segmented polyurethanes were studied. The structures of these polyurethanes were examined by FTIR and X-ray diffraction analysis. The thermal properties were investigated by differential scanning calorimetry and thermogravimetric analysis. Shore hardness and tensile properties were also determined. All the synthesized polymers showed partially crystalline structures. The MDI-based polyurethanes were products with lower crystallinity, higher glass-transition temperature (T_g) and better thermal stability in comparison with the HDI-based ones. The MDI series polymers also exhibited higher tensile strength (up to ∼36 MPa vs. ∼23 MPa) and elongation at break (up to ∼3900% vs. ∼900%), but lower hardness than the analogous HDI series polyurethanes. In both series of the polymers an increase in PTMO soft-segment content was associated with decreased crystallinity, T_g, hardness and tensile strength. An increase in PTMO content also involved an increase in elongation at break.     

Mechanical and dielectric properties of segmented polyurethane elastomers containing chemical crosslinks in the hard segment

Mechanical and dielectric properties of two series of segmented polyurethanes having soft segment concentration of 50 and 70% and a varying degree of crosslinking through the hard segment were studied. The degree of crosslinking in each series was varied by varying the butane diol/trimethylol propane ratio in the chain extender mixture. Tensile strength, elongation at break decrease, but elastic recovery increases monotonically with increasing crosslinking. The plateau modulus in the dynamic mechanical test decreases and then increases with increasing TMP content. Crosslinking causes broadening of the soft segment glass transition as seen by permittivity and loss factor measurements. It also affects high temperature behavior (above the glass transition of the hard segment); it lowers permittivity, loss factor, and ionic conductivity. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 237–251, 1998     

Magneto‐sensitive Elastomers in a Homogeneous Magnetic Field: A Regular Rectangular Lattice Model

A theory of mechanical behaviour of the magneto‐sensitive elastomers is developed in the framework of a linear elasticity approach. Using a regular rectangular lattice model, different spatial distributions of magnetic particles within a polymer matrix are considered: isotropic, chain‐like and plane‐like. It is shown that interaction between the magnetic particles results in the contraction of an elastomer along the homogeneous magnetic field. With increasing magnetic field the shear modulus, G, for the shear deformation perpendicular to the magnetic field increases for all spatial distributions of magnetic particles. At the same time, with increasing magnetic field the Young's modulus, E, for tensile deformation along the magnetic field decreases for both chain‐like and isotropic distributions of magnetic particles and increases for the plane‐like distribution of magnetic particles.

     

On the relevance of the 8‐chain model and the full‐network model for the deformation and failure of networks formed through photopolymerization of multifunctional monomers

Crosslinked networks were synthesized by copolymerization of mono‐functional tert‐butyl acrylate (tBA) with diethyleneglycol dimethacrylate (DEGDMA) or polyethylene glycol dimethacrylates (PEGDMA). By varying the chain length and concentration of the difunctional PEGDMA, we obtained tBA‐PEGDMA copolymer networks while by varying the concentration of difunctional DEGDMA, we obtained tBA‐DEGDMA crosslinked networks. The various materials were submitted to large deformations through uniaxial tension tests. For moderate weight percent of crosslinking agent, up to 20%, the networks showed standard S‐shape stress–strain curves, characteristic of rubber‐like elasticity. Two macromolecular models, the 8‐chain model and the full‐network model, were applied to fit the uniaxial tensile response of the materials. Both models provide good representations of the overall uniaxial stress–strain response of each material. After fitting to stress–strain data, the network models were employed to predict the shear modulus and the elongation at break. Neither the 8‐chain nor the full network model were capable of predicting the failure strain or shear modulus, indicating these models are best used to describe stress–strain relations rather than predict mechanical properties for the network polymers considered here. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1226–1234, 2008     

Polyisobutylene‐based polyurethanes with unprecedented properties and how they came about

This highlight concerns the birth, development, and present status of unique polyurethanes consisting of polyisobutylene soft segments and conventional hard segments (PIB‐based PUs) exhibiting unprecedented combinations of mechanical properties and oxidative/hydrolytic/biological stability. Impetus for developments was to improve the rather poor chemical resistance of conventional polyurethanes by replacing their soft segments with polyisobutylene segments. Research started in the 1980s with the synthesis of α,ω‐polyisobutylene diols (HO‐PIB‐OH) by the inifer technique and preparation of PIB‐based PUs, which indeed exhibited outstanding stabilities, however, had poor mechanical properties. Because of cumbersome early techniques and expensive reagents, worldwide research and industrial interest waned and developments went into hibernation. Recent discoveries, including living isobutylene polymerization, improved end‐functionalizations, inexpensive ingredients, and new insight into PU morphology, lead to simple and less expensive synthesis strategies and, consequently, to resumption of fundamental and applied research. Presently, we can produce kilogram quantities of polyurethanes and polyureas with unprecedented combinations of excellent physical–mechanical–environmental–biological and processing properties. This highlight focuses on facts and insights, which occurred since the discovery and shaped developments. These events are worth reviewing and analyzing because they illustrate how contemporary academic research is driven by curiosity (fun) and economic considerations (money). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Effects of humidity on Young's modulus in poly(methyl methacrylate)

Tensile tests on poly (methyl methacrylate) (PMMA) were conducted to clarify the effects of humidity and strain rate on tensile properties, particularly Young's modulus. Prior to the tensile tests, specimens were kept under various humidity conditions at 293 K, which were the same as the test conditions, for a few months to adjust the sorbed water content in the specimens. The tensile tests were performed under each humidity condition at three different strain rates (approximately 1.4 × 10^?3, 1.4 × 10^?4, and 1.4 × 10^?5 s^?1). Stress‐strain curves changed with humidity and strain rate. Young's moduli were also measured at small applied stresses (below 6.7 MPa) under various humidity conditions at 293 K. Young's modulus decreases linearly with increasing humidity and a decreasing logarithm of strain rate. These results suggest that Young's modulus of PMMA can be expressed as a function of two independent parameters that are humidity and strain rate. A constitutive equation for Young's modulus of PMMA was proposed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 460–465, 2002; DOI 10.1002/polb.10107     

Thermodynamics of the deformation of segmented polyurethanes with various hard block contents II. Stress softening and mechanical hysteresis

The thermodynamics of stress-softening and hysteresis in PBUs with different compositions were studied using deformational calorimetry, and the intramolecular energy contribution of the soft blocks was established. It is shown that differing from filled elastomers, the softening and hysteresis losses of PBU, like those of a typical TEP, are accompanied by energy absorption reflecting intermolecular change in the hard domains. Increased hard block content increases energy changes, whereas increasing the temperature produces the reverse effect. The dependence of the deformation mechanism of PBU on the hard block content, temperature and mechanical history is discussed.     

PIB‐based polyurethanes. IV. The morphology of polyurethanes containing soft co‐segments*

Novel polyurethanes consisting of polyisobutylene (PIB)/poly(tetramethylene oxide) (PTMO) or PIB/poly(hexamethylene carbonate) (PC) soft co‐segments in combination with 4,4′‐methylene‐bis(cyclohexyl isocyanate)/1,6‐hexanediol, 1,4‐butanediol, or 1,6‐hexamethylene diamine hard segments exhibit excellent mechanical properties (upto 31 MPa tensile strength with 700% elongation) together with unprecedented oxidative/hydrolytic stability. A structural model of the morphology of these polyurethanes was developed that reflects this combination of properties. The key new elements of our model are H bridges between the PTMO and PC type soft and urethane hard segments, which compatibilize the soft and hard domains, and the presence of large quantities of chemically resistant PIB soft segments that protect the other oxidatively/hydrolytically vulnerable constituents. A variety of FTIR, DSC, SAXS, AFM, and DMTA experiments strongly support the proposed morphological model. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6180–6190, 2009     

Effect of surface modification of colloidal silica nanoparticles on the rigid amorphous fraction and mechanical properties of amorphous polyurethane–urea–silica nanocomposites

Colloidal silica nanoparticles (NPs) modified with eight different silane coupling agents were incorporated into an amorphous poly(tetramethylene oxide)‐based polyurethane–urea copolymer matrix at a concentration of 10 wt % (4.4 vol %) in order to investigate the effect of their surface chemistry on the structure–property behavior of the resulting nanocomposites. The rigid amorphous fraction (RAF) of the nanocomposite matrix as determined by differential scanning calorimetry and dynamic mechanical analysis was confirmed to vary significantly with the surface chemistry of the NPs and to be strongly correlated with the bulk mechanical properties in simple tension. Hence, nanocomposites with an RAF of about 30 wt % showed a 120% increase in Young's modulus, a 25% increase in tensile strength, a 15% decrease in elongation at break with respect to the neat matrix, which had no detectable RAF, whereas nanocomposites with an RAF of less than 5% showed a 60% increase in Young's modulus, a 10% increase in tensile strength and a 5% decrease in the elongation at break. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2543–2556     

Theoretical implications of the elastic modulus discontinuity in rubber networks

The existence of a discontinuity in the modulus of rubber as the strain transitions from compression to extension is strongly suggested by multiple experiments. Classical rubber elasticity theories, however, do not admit such behavior. Here, we investigate a modification of the assumptions of classical elasticity theory to reconcile this discrepancy. We present an analysis of the consequences of assuming that chain forces are nonzero only for chain extension relative to the unstrained state, in contrast to the classical elasticity theory, which assumes that the chain force is directly proportional to the chain end‐to‐end distance (an entropic spring). Assuming an affine transformation of the network node coordinates, we derive two modulus discontinuity factors between compression and extension: D₁, based on the differing number of network chains being extended and D₂, based on the average differential chain extension. The discontinuities arise due to geometric effects, inherent in the affine transformation between compressive and extensive strains. We find that D₁, the ratio of the numbers of participating chains (compressive/extensive = 1.37), suffices to account for the experimentally observed modulus discontinuity in natural rubber of 1.34. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1795–1798, 2010     

Microporous polyurethanes: Synthesis and investigation of the mechanism of the pore formation

A new approach for microporous polymeric material is developed utilizing the secondary interactions such as hydrogen bonding in the polymer chains in polyurethane systems at ambient conditions. A new series of highly rigid, thermally stable, and readily soluble cycloaliphatic polyurethanes were designed and synthesized for this purpose, based on new tricyclodecanedimethanol and 1,4‐cyclohexanedimethanol. The hydrogen‐bonding interactions induce phase separation in solution, which leads to polymer‐rich and solvent‐rich domains; subsequent evaporation of the solvent molecules results in micropores. The phase‐separation process in the polyurethane is found to be highly dependent on the chemical structures of the polymer chain backbone. ¹H NMR titration experiments were carried out to understand the mechanism of the micropore formation and its dependence on different structural subunits. The hydrogen‐bonding association constant (K) obtained from the titration experiments revealed that higher the K‐value more the tendency to form micropores. A fully cycloaliphatic polyurethane produces micropores of sizes ranging from 1 to 8 μm, and each pore is separated by 10^?20 μm, whereas the replacement of one of the cyclic unit in the backbone disturbs the entire phase‐separation process and results in nonporous morphology. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1296–1308, 2006