Effect of low contents of a polyaniline derivative on the crystallization and electrical properties of blends with PVDF

The effect of low levels of poly(o‐methoxyaniline) (POMA) on the crystallization, morphology, and electrical characteristics of blends with poly(vinylidene fluoride) (PVDF) were studied by infrared spectroscopy, AC electrical measurements, and optical microscopy. Undoped POMA has a strong effect in increasing the α‐phase and decreasing the β‐phase content of PVDF in blends crystallized from solution. For blends melt crystallized, doped POMA promotes much greater homogeneity than undoped POMA. Interestingly, doped POMA promotes the nucleation and growth of unringed PVDF spherulites, whereas undoped POMA hinders it. The doping state of the POMA was also extremely important in determining the electrical behavior of the blend. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1219–1224, 1999     

Crystallization and morphology of poly(vinylidene fluoride)/poly(3‐hydroxybutyrate) blends. I. Spherulitic morphology and growth by polarized microscopy

The development of the poly(3‐hydroxybutyrate) (PHB) morphology in the presence of already existent poly(vinylidene fluoride) (PVDF) spherulites was studied by two‐stage solidification with two separate crystallization temperatures. PVDF formed irregular dendrites at lower temperatures and regular, banded spherulites at elevated temperatures. The transition temperature of the spherulitic morphology from dendrites to regular, banded spherulites increased with increasing PVDF content. A remarkable amount of PHB was included in the PVDF dendrites, whereas PHB was rejected into the remaining melt from the banded spherulites. When PVDF crystallized as banded spherulites, PHB could consequently crystallize only around them, if at all. In contrast, PHB crystallized with a common growth front, starting from a defined site in the interfibrillar regions of volume‐filling PVDF dendrites. It formed by itself dendritic spherulites that included a large number of PVDF spherulites. For blends with a PHB content of more than 80 wt %, for which the PVDF dendrites were not volume‐filling, PHB first formed regular spherulites. Their growth started from outside the PVDF dendrites but could later interpenetrate them, and this made their own morphology dendritic. These PHB spherulites melted stepwise because the lamellae inside the PVDF dendrites melted at a lower temperature than those from outside. This reflected the regularity of the two fractions of the lamellae because that of those inside the dendrites of PVDF was controlled by the intraspherulitic order of PVDF, whereas that from outside was only controlled by the temperature and the melt composition. The described morphologies developed without mutual nucleating efficiency of the components. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 873–882, 2003     

Composition distributions within poly(vinylidene fluoride) spherulites as grown in blends with poly(methyl methacrylate)

Upon crystalline solidification of one component in a homogeneously molten polymer blend, composition profiles develop outside (i.e., in the rest melt) and behind (i.e., within the spherulites) the crystal growth front. The present article is devoted to the detailed verification and the interpretation of these distributions and their temporal development inside growing spherulites. To this end, the energy dispersive X‐ray emission (EDX) of suitable elements has been recorded locally resolved in a scanning electron microscope and evaluated correspondingly. The investigations were performed at the melt homogeneous blend of poly(vinylidene fluoride) (PVDF) as crystallizing and poly(methyl methacrylate) (PMMA) as steadily amorphous component. If the spherulites are not volume filling, the mean PMMA content 〈?_PMMA〉 inside the PVDF spherulites is for all blends about 0.2 below the starting composition. ?_PMMA increases however slightly from the center of a spherulite to its border. That increase reflects the PMMA concentration in front of the spherulite surface, which increases likewise with time, and is clearly above the initial composition. There is at the spherulite surface, consequently, a remarkable jump in composition from the spherulite internal to its amorphous surroundings. It may amount up to 0.5. With volume filling spherulites, a slight variation of the composition from the center of a spherulite to its border is observed, too. This proves that also at these conditions composition profiles develop in the spherulite's surroundings. They remain however so weak that they do not inhibit crystallization even in its later stages. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 338–346, 2006     

Crystallization and structure formation in polymer blends with strong intermodular interactions: blends of poly(ethylene oxide) and styrene-hydroxystyrene copolymers

Time-resolved synchrotron wide- and small-angle X-ray scattering experiments were used to investigate crystallization behavior and microstructure development of a nearly monodisperse poly(ethylene oxide) [PEO] (M_w = 53,500), and its melt-miscible blends with two fractionated styrene - hydroxystyrene random copolymers [SHS]. PEO crystallization rates decrease significantly in the presence of the melt-miscible SHS copolymers. All low and high molecular weight SHS blends exhibit a crystallization process at relatively short times characterized by large Avrami exponents (n), followed by a dominant process with n near that of neat PEO. A model for the crystallization of these blends is proposed.     

Crystallization and morphology of poly(vinylidene fluoride)/poly(3‐hydroxybutyrate) blends. II. Morphology and crystallization kinetics by time resolved X‐ray scattering

The development of the morphology in poly(vinylidene fluoride)/poly(3‐hydroxybutyrate) (PVDF/PHB) blends upon isothermal and anisothermal crystallization is investigated by time‐resolved small‐ and wide‐angle X‐ray scattering. The components are completely miscible in the melt but crystallize separately; they crystallize stepwise at different temperatures or sequentially with isothermal or anisothermal conditions, respectively. The PVDF crystallizes undisturbed whereas PHB crystallizes in a confined space that is determined by the existing supermolecular structure of the PVDF. The investigations reveal that composition inhomogeneities may initially develop in the remaining melt or in the amorphous phases of the PVDF upon crystallization of that component. The subsequent crystallization of the PHB depends on these heterogeneities and the supermolecular structure of PVDF (dendritically or globularly spherulitic). PHB may form separate spherulites that start to grow from the melt, or it may develop “interlocking spherulites” that start to grow from inside a PVDF spherulite. Occasionally, a large number of PVDF spherulites may be incorporated into PHB interlocking spherulites. The separate PHB spherulites may intrude into the PVDF spherulites upon further growth, which results in “interpenetrating spherulites.” Interlocking and interpenetrating are realized by the growth of separate lamellar stacks (“fibrils”) of the blend components. There is no interlamellar growth. The growth direction of the PHB fibrils follows that of the existing PVDF fibrils. Depending on the distribution of the PHB molecules on the interlamellar and interfibrillar PVDF regions, the lamellar arrangement of the PVDF may contract or expand upon PHB crystallization and the adjacent fibrils of the two components are linked or clearly separated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 974–985, 2004     

Crystallization in PHB/DGEBA blends

Real‐time experiments using small‐angle X‐ray scattering and differential scanning calorimetry on blends of the semicrystalline polyester poly(3‐hydroxybutyrate) (PHB) and amorphous monomer epoxy DGEBA (diglycidyl ether of bisphenol A) were performed. Differences in the processes of melting and re‐crystallization were observed in blends relative to pure PHB. The results obtained in this study indicated that re‐crystallization is more important in blends with 50% DGEBA than in pure PHB. Moreover, segregation toward the interfibrillar region would facilitate re‐crystallization. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 882–886     

Morphology and crystallization of blends of linear low density polyethylene with a semiflexible liquid crystalline polymer

The morphology and the crystallization behavior of blends of linear low density polyethylene (LLDPE) with an experimental sample of a semiflexible liquid crystalline polymer (SBH 112 by Eniricerche, Italy) have been studied by differential scanning calorimetry (DSC), polarized optical microscopy (POM) and scanning electron microscopy (SEM). The blends possess a two-phase morphology, due to immiscibility of the two components. SEM observations show that dispersion of the minor SBH phase is favored at low (相似文献   

Effect of miscible polymer diluents on the development of lamellar morphology in poly(oxymethylene) blends

The development of lamellar morphology in poly(oxymethylene) (POM) and its miscible blends was studied by synchrotron time-resolved small-angle X-ray scattering (SAXS), during primary and secondary crystallization at temperatures near 150°C. The blends contained two different diluents: poly(vinyl 4-hydroxy styrene) [common name poly(vinyl phenol), (PVP)], which had a high glass temperature (T_g = 150°C), and styrene-co-hydroxy styrene oligomer (PhSO), which had a low glass temperature (T_g = −37°C). The SAXS data were analyzed by correlation function analysis to extract several lamellar parameters: long period (L), lamellar crystalline thickness (lc), amorphous layer thickness (la), and invariant (Q). The variation in Q defined the region where spherulites quickly grew and filled the entire space, and was referred to as the primary crystallization dominant regime. A rapid drop in L and lc was observed at early times, and this can be explained by defective lamellar stacks filling in space between primary stacks, as secondary crystals form during the nominal primary crystallization dominant regime. Lamellar thickening with time in the long-time secondary crystallization region was observed in neat POM and the blend with 10 % low T_g diluent, while this process was inhibited with the high T_g diluent due to the higher T_g of the interlamellar species. A decrease in la at long times confirmed the lamellar thickening. We refer to the lamellar thickening process as a type of secondary crystallization. Interlamellar inclusion or trapping was detected to different degrees with the high T_g diluent, while exclusion was found for the low T_g diluent. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 3115–3122, 1999     

Crystallization kinetics and morphology of binary phenolic/poly(ϵ-caprolactone) blends

For the first time, quantitative analyses of the crystallization kinetics, surface free energy of chain folding, and morphology in phenolic/poly(ϵ-caprolactone) (PCL) binary blends have been studied. The spherulite growth rate and the overall crystallization rate depend on the crystallization temperature and PCL content in the blend. In addition, the crystallization and melting temperatures of the PCL phase decrease with an increase in the phenolic content. An Avrami analysis shows that the addition of phenolic to PCL results in a decrease in the overall crystallization rate of the PCL phase. The presence of an amorphous phenolic phase results in a reduction in the rate of the spherulite growth of PCL. The surface free energy of folding increases with increasing phenolic content, and the crystal thickness of a phenolic/PCL blend, according to small-angle X-ray scattering (SAXS), is greater than that of pure PCL because of the increase in the surface free energy of chain folding and the decrease in the degree of supercooling. The observed domain size of the crystalline/amorphous phase (5.9 nm) from SAXS is also consistent with that from solid-state NMR (3–20 nm). All these results indicate that the crystallization ability of PCL decreases with increasing phenolic content in the blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 117–128, 2004     

Polymerization of Acrylamide Initiated by the Redox System Potassium Persulfate/Lactic Acid,Catalyzed by Silver Ions

The aqueous polymerization of acrylamide initiated by the potassium persulfate/lactic acid system catalyzed by Ag⁺ ions has been studied iodometrically over the temperature range from 35 to 50 ± 0.2°C. The rate of polymerization is governed by the expression R_p ∞ [M]^0.8[K₂S₂O₈]^1.0[Ag]^1.0 The deviation from normal kinetics has been studied. A tentative mechanism of initiation is suggested. The overall energy of activation is 5.52 kcal/mol.     

Fine structure of poly(vinylidene fluoride) membranes prepared by phase inversion from a water/N‐methyl‐2‐pyrollidone/poly(vinylidene fluoride) system

Poly(vinylidene fluoride) (PVDF) membranes were prepared by the isothermal immersion and precipitation of PVDF/N‐methyl‐2‐pyrollidone dope solutions in either harsh or soft nonsolvent baths. Low‐voltage field emission scanning electron microscopy imaging of the formed membranes at high magnifications (e.g., 300,000×) revealed their nanoscale fine structures, particularly dendrites observed on the surfaces of the macrovoids, cellular pores, and the membrane skin, which have never been successfully presented in the literature. Evidence of crystallization was also demonstrated by X‐ray diffraction and differential scanning calorimetry measurements. The phase diagram at 25 °C, including a binodal, tie lines, and a crystallization‐induced gelation line, was determined both experimentally and theoretically. These results were further used in mass‐transfer calculations to obtain diffusion trajectories and concentration profiles for the membrane region, which were useful for elucidating the relationship between the membrane preparation conditions and the obtained membrane morphologies. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 830–842, 2004     

Crystallization behavior of dynamically cured polypropylene/epoxy blends

Dynamically cured polypropylene (PP)/epoxy blends compatibilized with maleic anhydride grafted PP were prepared by the curing of an epoxy resin during melt mixing with molten PP. The morphology and crystallization behavior of dynamically cured PP/epoxy blends were studied with scanning electron microscopy, differential scanning calorimetry, and polarized optical microscopy. Dynamically cured PP/epoxy blends, with the structure of epoxy particles finely dispersed in the PP matrix, were obtained, and the average diameter of the particles slightly increased with increasing epoxy resin content. In a study of the nonisothermal crystallization of PP and PP/epoxy blends, crystallization parameter analysis showed that epoxy particles could act as effective nucleating agents, accelerating the crystallization of the PP component in the PP/epoxy blends. The isothermal crystallization kinetics of PP and dynamically cured PP/epoxy blends were described by the Avrami equation. The results showed that the Avrami exponent of PP in the blends was higher than that of PP, and the crystallization rate was faster than that of PP. However, the crystallization rate decreased when the epoxy resin content was greater than 20 wt %. The crystallization thermodynamics of PP and dynamically cured PP/epoxy blends were studied according to the Hoffman theory. The chain folding energy for PP crystallization in dynamically cured PP/epoxy blends decreased with increasing epoxy resin content, and the minimum of the chain folding energy was observed at a 20 wt % epoxy resin content. The size of the PP spherulites in the blends was obviously smaller than that of PP. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1181–1191, 2004     

Correlation of the minor-phase orientation to the flow-induced morphological transitions in thermotropic liquid crystalline polymer/PBT blends

Immiscible blends of thermotropic liquid crystalline polymers (TLCP) and a flexible polymer matrix show viscosity reductions and extensive fiber formation under certain flow conditions. Here we study these phenomena by directly examining the TLCP component's molecular orientation and the dispersed phase morphology. The rheology and morphology of blends of polybutylene terephthalate and a thermotropic copolyester (HX-8000 series, DuPont) at concentrations varying from 5 to 30 wt % of TLCP are characterized. It is found that the blends show viscosity reduction as well as stable fiber formation at shear rates dependent on the TLCP content. Wide-angle X-ray scattering is performed to measure the degree of molecular orientation of the TLCP phase. A deconvolution scheme isolates the scattering from the TLCP in the blends and a molecular model enables extracting an experimental orientation factor. It was found that a highly microfibrillated TLCP phase is coupled with an increase in the TLCP molecular orientation to values close to the pure TLCP at similar processing conditions. Further, the microfibrillated TLCP phase is found to be stable within the testing time. Current hypotheses about fiber formation in immiscible blends are tested against the experimental observations. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1769–1780, 1998     

Melting behavior in blends of isotactic polypropylene and a liquid crystalline polymer

The influence of low contents of a liquid crystalline polymer on the crystallization and melting behavior of isotactic polypropylene (iPP) was investigated using electron and optical microscopy, differential scanning calorimetry, and X-ray diffraction. In pure iPP, the α modification was found, whereas for iPP/Vectra blends at Vectra concentration <5%, both α and β forms were observed. The amount of β phase varied from 0.23 to 0.16. Optical microscopy showed that Vectra was able to nucleate both α and β forms. Non-isothermal crystallization produces a material with a strong tendency for recrystallization of the α and β forms (αα′ and ββ′ recrystallization) leading to double endotherms for both crystalline forms in DSC thermograms. Melting thermograms after isothermal crystallization at low temperatures showed a similar behavior. At values of T_c > 119 °C for the α form and T_c > 125 °C for the β form, only one melting endotherm was observed because enough perfect crystals, not susceptible to recrystallization, were obtained. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1949–1959, 2004     

Self-Reguiating Poiycondensations. II. A Study of the Order Present in Polyamide-Hydrazides Derived from Terephthaloyl Chloride and p-Aminobenzhydrazide

The problem of chemical order of polyamide-hydrazides prepared from terephthaloyl chloride with an unsymmetrical monomer, p-aminobenzhydrazide, is discussed. An NMR method for identifying the molecular structure of species formed in the early stages of poly condensation has enabled the course of a polymerization to be followed during this time and the final degree of order to be predicted qualitatively. These studies have provided a demonstration that the structure of these polymers can be controlled to a significant degree by appropriate variations in experimental conditions. But even under the most adverse conditions usually employed, poly amide-hydrazides are found to be at least “partially ordered” copolymers. The techniques developed for this study may find application in the study of other polymer forming reactions with monomers having two functional groups with dissimilar reactivities.     

Glass transition temperatures in binary polymer blends

Knowledge of the glass transition temperatures (T_gs) as function of composition reflects miscibility (or lack of it) and is decisive for virtually all properties of polymer‐based materials. In this article, we analyze single blend‐average and effective T_gs of miscible polymer blends in full concentration ranges. Shortcomings of the extant equations are discussed to support the need for an alternative. Focusing on the deviation from a linear relationship, defined as ΔT_g = T_g ? φ₁T_g,1 ? φ₂T_g,2 (where φ_i and T_g,i are, respectively, the weight fraction and the T_g of the i‐th component), a recently proposed equation for the blend T_g as a function of composition is tested extensively. This equation is simple; a quadratic polynomial centered around 2φ₁ ? 1 = 0 is defined to represent deviations from linearity, and up to three parameters are used. The number of parameters needed to describe the experimental data, along with their magnitude and sign, provide a measure of the system complexity. For most binary polymer systems tested, the results obtained with the new equation are better than those attained from existing T_g equations. The key parameter of the equation a₀ is related to parameters commonly used to represent intersegmental interactions and miscibility in binary polymer blends. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 80–95, 2008     

Miscibility and ferroelectric behavior in blends of poly(vinylidene fluoride/trifluoroethylene) and poly(vinyl acetate)

The blend system containing a poly(vinylidene fluoride/trifluoroethylene) [P(VDF/TrFE)] copolymer (68/32 mol %) and poly(vinyl acetate) (PVAc) was miscible from the results of differential scanning calorimetry (DSC) studies that exhibit the presence of a single, composition‐dependent glass transition temperature (T_g) and a strong melting point depression for the semicrystalline P(VDF/TrFE) component. However, differences between the DSC and dielectric measurements, which showed a separate P(VDF/TrFE) T_g peak, suggests that the P(VDF/TrFE)/PVAc blends are actually partially miscible. Because of the lower dielectric constant of PVAc and the reduced sample crystallinity caused by the addition of PVAc, both the dielectric constant and the remanent polarization of the copolymer blends decrease with increasing PVAc content. The presence of a small amount of PVAc stabilized the anomalous ferroelectric behavior of ice–water‐quenched P(VDF/TrFE), and the blend portrayed normal polarization reversal behavior after adding only 1 wt % PVAc. The piezoelectric response suggests small changes with an increasing number of poling cycles. It is believed that PVAc affects the D‐E hysteresis behavior at the interface between crystalline and amorphous phases, although much work remains to be done to confirm this hypothesis. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 927–935, 2003     

Thermal and mechanical behavior of amorphous and semi-crystalline poly(vinylidene fluoride)/poly(methyl methacrylate) blends

Various PVDF/PMMA (poly(vinylidene fluoride)/poly(methyl methacrylate)) blends were selected for mechanical testing in compression. At low PVDF content (less than 50/50 w/w), the blends remain amorphous and PVDF and PMMA are fully miscible. In PVDF-richer blends, PVDF crystallizes in part, leading to a PMMA-enriched homogeneous amorphous phase. In this study, the degree of crystallinity was set at equilibrium by appropriate annealing of the samples before testing. Mechanical analysis was focused on the low deformation range, and especially on the yield region. Depending on the test temperature and blend composition, three types of response were identified, depending on whether plastic deformation is influenced: 1) by the PMMA secondary relaxation motions, 2) by the PVDF/PMMA glass transition motions, or 3) by the crystallite-constrained PVDF chains.     

Investigation on LCST behavior of a new amorphous/crystalline polymer blend: Poly(n‐methyl methacrylimide)/poly(vinylidene fluoride)

The liquid–liquid phase‐separation (LLPS) behavior of poly(n‐methyl methacrylimide)/poly(vinylidene fluoride) (PMMI/PVDF) blend was studied by using small‐angle laser light scattering (SALLS) and phase contrast microscopy (PCM). The cloud point (T_c) of PMMI/PVDF blend was obtained using SALLS at the heating rate of 1 °C min^?1 and it was found that PMMI/PVDF exhibited a low critical solution temperature (LCST) behavior similar to that of PMMA/PVDF. Moreover, T_c of PMMI/PVDF is higher than its melting temperature (T_m) and a large temperature gap between T_c and T_m exists. At the early phase‐separation stage, the apparent diffusion coefficient (D_app) and the product (2Mk) of the molecules mobility coefficient (M) and the energy gradient coefficient (k) arising from contributions of composition gradient to the energy for PMMI/PVDF (50/50 wt) blend were calculated on the basis of linearized Cahn‐Hilliard‐Cook theory. The kinetic results showed that LLPS of PMMI/PVDF blends followed the spinodal decomposition (SD) mechanism. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1923–1931, 2008