Preparation of co‐polymethyl(alkoxy)siloxanes by acid‐catalyzed controlled hydrolytic copolycondensation of methyl(trialkoxy)silane and tetraalkoxysilane

Polymethyl(alkoxy)siloxane copolymers, poly(MTES‐co‐TEOS), and poly(MTMS‐co‐TMOS), are prepared by acid‐catalyzed controlled hydrolytic co‐polycondensation of methyl(trialkoxy)silane MeSi(OR)₃ (R = Et (MTES) and Me (MTMS)) and tetra‐alkoxysilane Si(OR)₄ (R = Et (TEOS) and Me (TMOS)), respectively. The products are purified by fractional precipitation to provide polymethyl(alkoxy)siloxane copolymers with molecular weight 1000–10,000 (poly(MTES‐co‐TEOS)) or 1700–100,000 (poly(MTMS‐co‐TMOS)) that are stable to self‐condensation. These polymers are soluble in common organic solvents except for hexane, and form flexible and transparent free‐standing films with a tensile strength of 4.0–10.0 MPa. The structure of the polymethyl(alkoxy)siloxane copolymers is thought to be a random or a block co‐polymer. They are found to provide coating films with an adhesive strength up to 10, a refractive index of 1.36–1.40, and a dielectric constant of 3.5–3.6. The products also show better weathering stability than polyethoxysiloxane due to the hydrolytic polycondensation of TEOS. Field emission‐scanning electron micrography analysis reveals that coating films are composed of a micro‐phase separated structure. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4732–4741     

Poly(L‐lactide)/C60 nanocomposites: Effects of C60 on crystallization of poly(L‐lactide)

The effects of solvent type and concentration of C₆₀ on the crystallization of poly(L ‐lactide) (PLLA) during solvent evaporation, heating from room temperature, and cooling from the melt were investigated by polarized optical microscopy and differential scanning calorimetry. The addition of C₆₀ enhanced the PLLA crystallization during solvent evaporation, during heating of the melt‐quenched films, and during cooling from the melt of As‐cast films, except for heating and cooling of the PLLA film with 1 wt % of C₆₀ prepared with dichloromethane. In the case of solvent evaporation, the difference in crystallinity between the PLLA films with and without C₆₀ became higher for the solvent with a lower boiling point. In the case of heating of melt‐quenched films, the addition of C₆₀ had a small effect on the crystallinity of PLLA, whereas significantly lowered the peak top and ending temperatures of cold crystallization, except for melt‐quenched PLLA film with 1 wt % of C₆₀ prepared with dichloromethane. The crystallinity of PLLA was determined by the solvent type, rather than by the C₆₀ concentration. In the case of cooling from the melt of As‐cast films, the addition of C₆₀ elevated the crystallinity and cold crystallization temperature values of PLLA films, except for PLLA films prepared with dichloromethane. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2167–2176, 2007     

Low potential electrosyntheses of free‐standing poly(dibenzofuran) films in mixed electrolytes of boron trifluoride diethyl etherate and trifluoroacetic acid

Free‐standing poly(dibenzofuran) (PDBF) films were synthesized electrochemically by direct anodic oxidation of dibenzofuran in mixed electrolytes of boron trifluoride diethyl etherate (BFEE) containing certain amount of trifluoroacetic acid (TFA). The oxidation potential of dibenzofuran in pure BFEE was measured to be only 1.31 V versus saturated calomel electrode (SCE). This value was much lower than that determined in acetonitrile + 0.1 mol L^?1 TBATFB (2.14 V vs. SCE). The addition of TFA to BFEE can further decrease the oxidation potential of the monomer to 1.07 V versus SCE in the mixed electrolyte of BFEE + 30% TFA. PDBF films obtained from this medium showed good electrochemical behavior, good electrochromic properties, and good thermal stability with conductivity of 10⁰ S cm^?1. FTIR and ¹H NMR spectra showed that the polymer was grown mainly via the coupling of the monomer at C₍₃₎ C₍₁₀₎ or C₍₄₎ C₍₉₎ positions (Scheme 1). As‐formed PDBF films were partly soluble in tetrahydrofuran (THF) or chloroform. Fluorescent spectral studies indicated that either soluble or PDBF in solid state was a good blue light PDBF emitter. To the best of our knowledge, this is the first report that free‐standing PDBF films can be electrodeposited. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1125–1135, 2006     

Fabrication of novel conjugated polymer nanostructure: Porphyrins and fullerenes conjugately linked to the polyacetylene backbone as pendant groups

A new series of conjugated polyacetylenes with conjugately linked fullerene and porphyrin groups as pendant units were prepared by a copolymerization reaction catalyzed by chloronorbornadiene rhodium(I)dimer‐triethylamine ([Rh(nbd)Cl]₂‐NEt₃) in anhydrous CHCl₃. These polymers were characterized with UV–vis spectroscopy, fluorescence spectroscopy, and voltammetry. Scanning electron microscopy indicated that the morphology of the copolymers consisted of uniform nanorods with a diameter of about 100 nm and a length of about 300 nm. Thin films of the copolymers produced steady and prompt photocurrent at an irradiation of 20.0 mW cm^?2 of white light, which was higher than that of a mixture of poly[5‐(4‐Ethynyl‐phenyl)‐10,15,20‐tris(4‐carbomethoxyphenyl)porphyrin zinc] and C₆₀. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2851–2861, 2005     

Thiourethane‐based thiol‐ene high Tg networks: Preparation,thermal, mechanical,and physical properties

Thiourethane‐based thiol‐ene (TUTE) films were prepared from diisocyanates, tetrafunctional thiols and trienes. The incorporation of thiourethane linkages into the thiol‐ene networks results in TUTE films with high glass transition temperatures. Increases of T_g were achieved by aging at room temperature and annealing the UV cured films at 85 °C. The aged/annealed film with thiol prepared from isophorone diisocyanate and cured with a 10,080‐mJ/cm² radiant exposure had the highest DMA‐based glass transition temperature (108 °C) and a tan δ peak with a full width at half maximum (FWHM) of 22 °C, indicating a very uniform matrix structure. All of the initially prepared TUTE films exhibited good physical and mechanical properties based on pencil hardness, pendulum hardness, impact, and bending tests. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5103–5111, 2007     

Low‐potential facile electrosynthesis of free‐standing poly(1H‐benzo[g]indole) film as a yellow‐light‐emitter

High‐quality free‐standing poly(1H‐benzo[g]indole) (PBIn) films were synthesized electrochemically by direct anodic oxidation of 1H‐benzo[g]indole (BIn) in boron trifluoride diethyl etherate. PBIn films obtained from this medium showed good electrochemical behavior and better thermal stability with a conductivity of 0.29 S cm^?1. PBIn films with low band gap value (1.59 eV) were insoluble in acetone and tetrahydrofuran. The structure and morphology of the polymer were studied by UV–vis, FTIR, and scanning electron microscopy, respectively. The results of quantum chemistry calculations and the spectroscopies of dedoped PBIn indicate that the polymerization of BIn mainly occurs via C₍₂₎ and C₍₅₎ position. The polymer film was compact with regular nanoparticles on the surface. Fluorescent spectral studies indicate that solid‐state PBIn film is a good yellow‐light‐emitter. Thermal stability of PBIn film is higher than poly(indole‐6‐carboxylic acid), poly(5‐formylindole), and polyindole. To the best of our knowledge, this is the first report on the electrosynthesis of free‐standing polyindole derivatives as yellow‐light‐emitter. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2730–2738     

Judiciously balancing steric and electronic influences on 2,3‐diiminobutane‐based Pd(II) complexes in nourishing polyethylene properties

A new series of palladium complexes ( Pd1–Pd5 ) ligated by symmetrical 2,3‐diiminobutane derivatives, 2,3‐bis[2,6‐bis{bis(4‐FC₆H₄)₂CH}₂‐4‐(alkyl)C₆H₂N]C₄H₆ (alkyl = Me L1 , Et L2 , ⁱ Pr L3 , ^t Bu L4 ) and 2,3‐bis[2,6‐bis{bis(C₆H₅)₂CH}₂‐4‐{(CH₃)₃C}C₆H₂N]C₄H₆ L5 , have been prepared and well characterized, and their catalytic scope toward ethylene polymerization have been investigated. Upon activation with MAO, all palladium complexes ( Pd1–Pd5) exhibited good activities (up to 1.44 × 10⁶ g (PE) mol^?1(Pd) h^?1) and produced higher molecular weight polyethylene in the range of 10⁵ g mol^?1 with precise molecular weight distribution (M _w/M _n = 1.37–1.77). One of the long‐standing limiting features of the Brookhart type α‐diimine Pd(II) catalysts is that they produce highly branched (ca. 100/1000 C atoms) and totally amorphous polymer. Conversely, herein Pd5 produced polymers having dramatically lower branching number (28/1000) as well as improved melting temperature up to 73.1 °C showing well‐controlled linear architecture, and very similar to polyethylene materials generated by early‐transition‐metal based catalysts. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 3214–3222     

Adsorption of long-chain aliphatic amines—components of corrosion inhibitors

Adsorption of certain long-chain aliphatic amines with 6–18 carbon atoms is studied on a stationary mercury drop electrode using the impedance method. It is found that adsorption of amines with C₆–C₁₂ results in the formation of an adsorption layer with the limiting capacitance of about 5 μF/cm². In the case of amines with C₁₄–C₁₆, the limiting capacitance is approximately 0.5–0.7 μF/cm². The most probable reason for such abrupt decrease in the adsorption layer capacitance is the formation of condensed layers of adsorbate molecules at the electrode surface. The adsorption parameters are calculated for hexylamine. The surface activity is estimated for amines with 10–14 carbon atoms in their chains.     

New approaches for the synthesis of hindered C60‐containing polyphosphazenes via functionalized intermediates

Two new approaches were developed to synthesize C₆₀‐containing polyphosphazenes. Accordingly, two new reactive macromolecular intermediates ( P4 and P8 ) were obtained from poly(dichlorophosphazene) by the direct nucleophilic substitution reaction. In one approach, a predesigned amimo end–functionalized polyphosphazene ( P4 ) was prepared and then reacted with C₆₀ molecules in chlorobenzene to yield C₆₀‐containing polyphosphazene; in the other approach, a polyphosphazene containing 4‐methyl phenoxy groups as side chains was first prepared, and then part of the 4‐methyl groups were converted to azidomethyl groups (in P8 ), which reacted with C₆₀ to yield C₆₀‐containing polyphosphazene. The polymers were characterized by ¹H NMR, ¹³C NMR, IR, and UV–visible spectra and by gel permeation chromatography. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2877–2885, 2004     

Synthesis of photocrosslinkable hyperbranched polyesters and their film properties

Hyperbranched polyesters with terminal methacryloyl groups (HBPEAc) were synthesized by the one‐pot polyaddition of bisphenol A diglycidyl ether and trimesic acid in the presence of methacrylic acid with a number‐average molecular weights of 5100–7700 in 70–83% yields. The photoradical polymerization of HBPEAc was examined in the presence of 2‐methyl‐1‐[4‐(methylthio)phenyl]‐2‐morpholinopropan‐2‐one (Irgacure 907®) as a photoinitiator in the film state upon UV irradiation to afford the corresponding cured films quantitatively. The crosslinking densities of the cured films of HBPEAc were higher than those of the corresponding linear ones, and birefringence cannot be detected for the cured films of HBPEAc because of their random structures. Furthermore, an alkaline‐developable hyperbranched polyester containing pendant carboxyl groups (HBPEAc‐COOH) was prepared by the addition reaction of HBPEAc with cis‐1,2,3,6‐tetrahydrophthalic anhydride, and its patterning properties were examined to give the resolution of a 55‐μm‐line and 275‐μm‐space pattern by UV irradiation with 700 mJ/cm². © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4642–4653, 2005     

Low potential electrochemical polymerization of diphenyl ether and characterization of its polymers

High‐quality poly(diphenyl ether) (PDPE) films with electrical conductivity of 4.4 × 10^?1 S cm^?1 were synthesized electrochemically by direct anodic oxidation of diphenyl ether (DPE) in boron trifluoride diethyl etherate (BFEE) containing 5% concentrated sulfuric acid (SA) (by volume). The oxidation potential onset of DPE in pure BFEE was measured to be only 1.37 V versus a saturated calomel electrode (SCE), which was much lower than that determined in acetonitrile + 0.1 mol L^?1 tetrabutylammonium tetrafluoroborate (1.98 V vs. SCE). The addition of SA to BFEE can further decrease the oxidation potential onset of the monomer to 1.18 V versus SCE in the mixed electrolyte of BFEE + 5% SA. PDPE films obtained from this medium showed good redox activity and stability even in concentrated SA. Dedoped PDPE films were partly soluble in the strong polar organic solvent dimethyl sulfoxide. Fluorescent spectral studies indicated that soluble PDPE was a good blue‐light emitter with a quantum yield of 0.30. Infrared spectroscopy and quantum chemistry calculations indicated that the electropolymerization of DPE occurred mainly at C₄ and C_4′. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5932–5941, 2007     

Field effect conductance of conducting polymer nanofibers

We report on the electrical conductance of nanofibers of regioregular poly(3‐hexylthiophene) (RRP3HT) as a function of gate‐induced charge. Nanofibers of RRP3HT were deposited onto SiO₂/Si substrates by casting from dilute p‐xylene solutions. An analysis of the nanofibers by atomic force microscopy revealed fiber lengths of 0.2–5 μm, heights of 3–7 nm, and widths of approximately 15 nm. A field effect transistor geometry was used to probe the conductance of webs of nanofibers and single nanofibers; in these measurements, gold electrodes served as source and drain contacts, and the doped SiO₂/Si substrate served as the gate. Temperature‐dependent transport studies on webs of nanofibers revealed an activation energy of 108 meV at a gate‐induced hole density of 3.8 × 10¹² charges/cm². Pretreating SiO₂ with a hydrophobic hexamethyldisilazane (HMDS) layer reduced the activation energy to 65 meV at the same charge density. The turn‐on gate voltage on treated and untreated substrates increased in magnitude with decreasing temperature. Conductance measurements on single nanofibers on HMDS‐treated SiO₂ yielded hole mobilities as high as 0.06 cm²/Vs with on/off current ratios greater than 10³. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2674–2680, 2003     

Solid polymer electrolytes I,preparation, characterization,and ionic conductivity of gelled polymer electrolytes based on novel crosslinked siloxane/poly(ethylene glycol) polymers

A series of crosslinked siloxane/poly(ethylene glycol) (Si–PEG) copolymers were synthesized from the reactive methoxy‐functional silicone resin (Si resin) and PEGs with different molecular weights via two kinds of crosslinking reactions during an in situ curing stage. One of the crosslinking reactions is the self‐condensation between two methoxy groups in the Si resin, and another one is an alkoxy‐exchange reaction between the methoxy group in the Si resin and the OH group in PEG. The synthesized crosslinked copolymers were characterized by Fourier transform infrared spectroscopy, DSC, and ¹³C NMR. The crosslinked copolymers were stable in a moisture‐free environment, but the Si? O? C linkages were hydrolyzed in humid conditions. The gel‐like solid polymer electrolytes (SPEs) were prepared by impregnating these crosslinked Si–PEG copolymers in a propylene carbonate (LiClO₄/PC) solution. The highest conductivity reached 2.4 × 10^?4 S cm^?1 at 25 °C and increased to 8.7 × 10^?4 S cm^?1 at 85 °C. The conductivities of these gel‐type SPEs were affected by the content of LiClO₄/PC, the molecular weights of PEGs, and the weight fraction of the Si resin. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2051–2059, 2004     

Internal stress in plasma polymer films prepared by cascade arc torch polymerization

Thin plasma polymer films were deposited from several liquid monomers (mainly siloxane‐type monomers) in a low‐temperature cascade arc torch (CAT) reactor. The effects of monomer structures and plasma parameters on internal stress in the films were experimentally studied. By appropriately adjusting these factors, the internal stress in the film was reduced nearly two orders of magnitude from 10⁹ to 10⁷ dyn/cm². It was noted that the polymer films prepared from siloxane‐type monomers showed lower internal stress than their hydrocarbon counterpart. Fourier transform‐infrared spectroscopy (FTIR) studies indicated that a large amount of Si O Si structure from siloxane monomers, which are very flexible bonds, was preserved in the resultant plasma polymers. Ellipsometry results suggested that the internal stress can be qualitatively correlated with the refractive index of the plasma polymer film. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1577–1587, 1999     

Soluble alkyl substituted poly(3,4‐propylenedioxyselenophene)s: A new platform for optoelectronic materials

Optical and electrochemical properties of regiosymmetric and soluble alkylenedioxyselenophene‐based electrochromic polymers, namely poly(3,3‐dibutyl‐3,4‐dihydro‐2H‐selenopheno[3,4‐b][1,4]dioxephine) (PProDOS‐C₄), poly(3,3‐dihexyl‐3,4‐dihydro‐2H‐selenopheno[3,4‐b][1,4]dioxephine) (PProDOS‐C₆), and poly(3,3‐didecyl‐3,4‐dihydro‐2H‐selenopheno[3,4‐b][1,4]dioxephine) (PProDOS‐C₁₀), are highlighted. It is noted that these unique polymers have low bandgaps (1.57–1.65 eV), and they are exceptionally stable under ambient atmospheric conditions. Polymer films retained 82–97% of their electroactivity after 5000 cycles. The percent transmittance of PProDOS‐C_n (n = 4, 6, 10) films found to be between 55 and 59%. Furthermore, these novel soluble PProDOS‐C_n polymers showed electrochromic behavior: a color change form pure blue to highly transparent state in a low switching time (1.0 s) during oxidation with high coloration efficiencies (328–864 cm² C^?1) when compared to their thiophene analogues. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Annealing Temperature Dependence of the Size of C60 Clusters in C60-Doped Silicon Oxide Films

C₆₀-doped silicon oxide thin films were prepared by spin-coating a viscous solution formed upon soaking at 40°C an acidic toluene/ethanol solution of C₆₀, phenyltriethoxysilane, and tetraethoxysilane with a C₆₀–to–Si molar ratio of 2.5 × 10^–3. The films were submitted to annealing at 300–500°C in Ar to investigate variation in the size of C₆₀ clusters embedded in the films by photoluminescence spectroscopy. The film before annealing was found to contain the clusters consisting of ca. 60 C₆₀ molecules, suggesting that C₆₀ is present well-dispersed in the film. The molecules in the film aggregated to increase the size with increasing annealing temperature, indicating that the molecules diffuse easily in the film upon heating and therefore the size of the clusters is controllable with the annealing temperature.     

Synthesis of a [60]fullerene‐functionalized poly(vinyl chloride) derivative by stereospecific chemical modification of PVC

The covalent attachment of [60]fullerene (C₆₀) to two poly(vinyl chloride) (PVC) samples with different isotactic content is achieved by direct reaction in o‐dichlorobenzene (o‐DCB) solution in the presence of AIBN. The extent of fullerenation is controlled by varying the C₆₀ feed ratio. The pendant C₆₀‐chemically modified PVC polymers are soluble in tetrahydrofuran (THF) and have been characterized by UV–vis, NMR, FTIR, DSC, TGA, cyclic voltammetry, and SEM. The quantitative microstructural analysis after covalent attachment of the bulky C₆₀ moiety to the PVC has been followed by ¹³C NMR spectroscopy. From the results it can be concluded that the modification of PVC by graft reaction through free radical reaction proceeds by a stereoselective mechanism. This conclusion has been confirmed on the basis of the increase of the glass‐transition temperature (T_g) and the thermal stability of the C₆₀‐chemical modified PVC samples. The fullerenated PVCs obtained show good electron acceptor properties, as evidenced by electrochemical investigations. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5408–5419, 2007     

Supramacromolecular chemistry: Self‐assembly of polystyrene‐based multi‐armed pseudorotaxane star polymers from multi‐topic C60 derivatives

Multitopic dibenzylammonium derivatives ( 4 ) of C₆₀ were prepared by Bingel reactions of C₆₀ with a malonate diester ( 2 ) containing two t‐BOC protected dibenzylamine moieties, followed by deprotection and protonation. Self‐assembly of model pseudorotaxanes 5 from the multidibenzylammonium C₆₀ derivatives with dibenzo‐24‐crown‐8 was studied by ¹H NMR spectroscopy and mass spectrometry. Self‐assembly of linear and star‐shaped pseudorotaxanes 8 with up to 12 arms based on polystyrenes bearing terminal DB24C8 host units ( 7 ) and the guest functionalized C₆₀ salts was demonstrated by ¹H NMR spectroscopy and solution phase viscometry. These studies provide further evidence of the potential of supramacromolecular chemistry in construction of complex polymeric architectures. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6472–6495, 2009     

Synthesis and properties of Q‐silicon crosslinked siloxane networks: H3PO4‐catalyzed sol–gel dehydration/crosslinking of α,ω‐bis(hydroxy)oligodimethylsiloxanes with tetrakis(hydroxydimethylsiloxy)silane

Six silicate‐crosslinked oligodimethylsiloxane thin films were prepared by the phosphoric acid (1 mol %) catalyzed condensation of α,ω‐bis(hydroxy)oligodimethylsiloxane (P) and tetrakis(hydroxydimethylsiloxy)silane (Q). Other acid catalysts were evaluated. P and Q were prepared by the Pd‐catalyzed oxidation of the corresponding Si? H compounds with water. The starting materials were characterized by IR and ¹H, ¹³C, and ²⁹Si NMR. A thermal cure was achieved with H₃PO₄ in 24 h and with poly(phosphoric acid) in 3 h at 110–120 °C. Dynamic mechanical analysis was used to determine the glass‐transition temperatures and to evaluate the mechanical properties of the films. Their thermal stabilities (≥300 °C) in air and N₂ were determined by thermogravimetric analysis. Small amounts of non‐crosslinked P were recovered from the films by Soxhlet extractions with CH₂Cl₂ and analyzed by IR, gel permeation chromatography, and ²⁹Si NMR. The crosslink densities were evaluated by the CH₂Cl₂ absorption capacities of the films. The surface properties of the films were determined by static and dynamic contact‐angle measurements. Electrochemical impedance spectroscopy was carried out to evaluate the corrosion‐protective properties of the coatings on mild steel as a function of the exposure time to 0.5 N NaCl. The biofoul‐release properties of the films were evaluated with sporelings from mature Ulva linza plants and barnacles. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2237–2247, 2006     

Fluorene‐based alternating polymers containing electron‐withdrawing bithiazole units: Preparation and device applications

We report here the synthesis via Suzuki polymerization of two novel alternating polymers containing 9,9‐dioctylfluorene and electron‐withdrawing 4,4′‐dihexyl‐2,2′‐bithiazole moieties, poly[(4,4′‐dihexyl‐2,2′‐bithiazole‐5,5′‐diyl)‐alt‐(9,9‐dioctylfluorene‐2,7‐diyl)] (PHBTzF) and poly[(5,5′‐bis(2″‐thienyl)‐4,4′‐dihexyl‐2,2′‐bithiazole‐5″,5″‐diyl)‐alt‐(9,9‐dioctylfluorene‐2,7‐diyl)] (PTHBTzTF), and their application to electronic devices. The ultraviolet–visible absorption maxima of films of PHBTzF and PTHBTzTF were 413 and 471 nm, respectively, and the photoluminescence maxima were 513 and 590 nm, respectively. Cyclic voltammetry experiment showed an improvement in the n‐doping stability of the polymers and a reduction of their lowest unoccupied molecular orbital energy levels as a result of bithiazole in the polymers' main chain. The highest occupied molecular orbital energy levels of the polymers were ?5.85 eV for PHBTzF and ?5.53 eV for PTHBTzTF. Conventional polymeric light‐emitting‐diode devices were fabricated in the ITO/PEDOT:PSS/polymer/Ca/Al configuration [where ITO is indium tin oxide and PEDOT:PSS is poly(3,4‐ethylenedioxythiophene) doped with poly(styrenesulfonic acid)] with the two polymers as emitting layers. The PHBTzF device exhibited a maximum luminance of 210 cd/m² and a turn‐on voltage of 9.4 V, whereas the PTHBTzTF device exhibited a maximum luminance of 1840 cd/m² and a turn‐on voltage of 5.4 V. In addition, a preliminary organic solar‐cell device with the ITO/PEDOT:PSS/(PTHBTzTF + C₆₀)/Ca/Al configuration (where C₆₀ is fullerene) was also fabricated. Under 100 mW/cm² of air mass 1.5 white‐light illumination, the device produced an open‐circuit voltage of 0.76 V and a short‐circuit current of 1.70 mA/cm². The fill factor of the device was 0.40, and the power conversion efficiency was 0.52%. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1845–1857, 2005