Interfacial interaction in EVA‐carbon nanotube and EVA‐clay nanocomposites

Proper filler‐matrix compatibility is a key factor in view of obtaining nanocomposites with well‐dispersed nanofillers displaying enhanced properties. In this respect, polymer‐filler interaction can be improved by a proper combination of matrix and nanofiller polarities. This is explored for matrices ranging from nonpolar high density poly(ethylene) to ethylene‐vinyl acetate (EVA) copolymers with varying vinyl acetate contents, in combination with several types of organoclay or carbon nanotubes. A novel in situ characterization methodology using modulated temperature differential scanning calorimetry is presented to evaluate the matrix‐filler interaction. During quasi‐isothermal crystallization of the matrix, an “excess” contribution is observed in the recorded heat capacity signal because of reversible melting and crystallization. Its magnitude considerably decreases upon addition of nanofiller in case of strong interfacial interaction, whereas the influence is moderate in case of a less interacting matrix‐filler combination. It is suggested that the “excess heat capacity” can be used to quantify the segmental mobility of polymer chains in the vicinity of the nanofiller. Hence it provides valuable information on the strength of interaction, governed by the physical and chemical nature of matrix and filler. Heating experiments subsequent to quasi‐isothermal crystallization point at a certain degree of molecular ordering, responsible for crystal nucleation in EVA copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1291–1302, 2007     

Photo‐induced surface transformations of silica nanocomposites

The photo‐induced, physicochemical surface transformations to silica nanoparticle (SiNP) ‐ epoxy composites have been investigated. The silica nanocomposites (SiNCs) were prepared using a two‐part epoxy system with a 10% mass fraction of SiNPs and exposed to varying doses of high intensity, ultraviolet (UV) radiation at wavelengths representative of the solar spectrum at sea level (290 nm to 400 nm) under constant temperature and humidity. Visibly apparent physical modifications to the SiNC surface were imaged with scanning electron microscopy. Surface pitting and cracking became more apparent with increased UV exposure. Elemental and surface chemical characterization of the SiNCs was accomplished through X‐ray energy dispersive spectroscopy and X‐ray photoelectron spectroscopy, while attenuated total reflectance Fourier transform infrared spectroscopy revealed changes to the epoxy's structure. During short UV exposures, there was an increase in the epoxy's overall oxidation, which was accompanied by a slight rise in the silicon and oxygen components and a decrease in overall carbon content. The initial carbon components (e.g. aliphatic, aromatic and alcohol/ether functionalities) decreased and more highly oxidized functional groups increased until sufficiently long exposures at which point the surface composition became nearly constant. At long exposure times, the SiNC's silicon concentration increased to form a surface layer composed of approximately 75% silica (by mass). Published 2012. This article is a U.S. Government work and is in the public domain in the USA.     

Zero‐order kinetics of the thermal degradation of polypropylene/clay nanocomposites

The thermal degradation kinetics of polypropylene/clay microcomposites and nanocomposites were studied by thermogravimetric analysis. In comparison with pure polypropylene, the reaction order of the degradation of the composites became zero‐order, and the activation energy increased dramatically. The zero‐order kinetics were associated with the acidic sites (H⁺) created on the clay layers, whereas the increase in the activation energy was coupled with the shielding effect of clay. The kinetic analysis could provide additional mechanistic clues concerning the thermal stability and flammability of polymer/clay nanocomposites. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3713–3719, 2005     

Isothermal crystallization kinetics of polypropylene latex–based nanocomposites with organo‐modified clay

The effect of organo‐modified clay (Cloisite 93A) on the crystal structure and isothermal crystallization behavior of isotactic polypropylene (iPP) in iPP/clay nanocomposites prepared by latex technology was investigated by wide angle X‐ray diffraction, differential scanning calorimetry and polarized optical microscopy. The X‐ray diffraction results indicated that the higher clay loading promotes the formation of the β‐phase crystallites, as evidenced by the appearance of a new peak corresponding to the (300) reflection of β‐iPP. Analysis of the isothermal crystallization showed that the PP nanocomposite (1% C93A) exhibited higher crystallization rates than the neat PP. The unfilled iPP matrix and nanocomposites clearly shows double melting behavior; the shape of the melting transition progressively changes toward single melting with increasing crystallization temperature. The fold surface free energy (σ_e) of polymer chains in the nanocomposites was lower than that in the PP latex (PPL). It should be reasonable to treat C93A as a good nucleating agent for the crystallization of PPL, which plays a determinant effect on the reduction in σ_e during the isothermal crystallization of the nanocomposites. The activation energy, ΔE_a, decreased with the incorporation of clay nanoparticles into the matrix, which in turn indicates that the nucleation process is facilitated by the presence of clay. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1927–1938, 2010     

Melt blending of ethylene‐vinyl alcohol copolymer/clay nanocomposites: Effect of the clay type and processing conditions

Ethylene‐vinyl alcohol copolymer (EVOH)/clay nanocomposites were prepared via dynamic melt blending. The effect of the processing parameters on blends containing two clay types in different amounts was examined. The blends were characterized with a Brabender plastograph and capillary rheometer, differential scanning calorimetry, dynamic mechanical thermal analysis (DMTA), X‐ray diffraction (XRD), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). XRD showed advanced EVOH intercalation within the galleries, whereas TEM images indicated exfoliation, thereby complementing the XRD data. A dilution process with EVOH and clay treatment in an ultrasonic bath before melt blending did not add to the intercalation level. Different trends were observed for the EVOHs containing two different clay treatments, one claimed to be treated for EVOH and the other for amine‐cured epoxy. They reflected the differences in the amounts of the strongly interacting polymer for the two nanocomposites. Thermal analysis showed that the melting temperature, crystallization temperature, and heat of fusion of the EVOH matrix sharply decreased with both increasing clay content and processing times. Significantly higher viscosity levels were obtained for the blends in comparison with those of the neat polymer. The DMTA spectra showed higher glass‐transition temperatures for the nanocomposites in comparison with those of the neat EVOH. However, at high clay loadings, the glass‐transition temperature remained constant, presumably because of an adverse plasticizing effect of the low moleculared mass onium ions treating the clays. The storage modulus improved when clay treated for EVOH was used, and it deteriorated when amine‐cured epoxy clay was incorporated, except for the sonicated clay. TGA results showed significant improvements in the blends' thermal stability in comparison with that of the neat EVOH, which, according to TEM, was greater for the intercalated structures rather than for exfoliated ones. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1741–1753, 2002     

Preparation of the polymer–clay nanocomposites in exfoliated state by interface stabilization

To suppress the repulsive interfacial energy between hydrophilic clay and a hydrophobic polymer matrix for polymer–clay nanocomposites, a third component of amphiphilic nature such as poly(?‐caprolactone) (PCL) was introduced into the styrene–acrylonitrile copolymers (SAN)/Na‐montmorillonite system. Once ?‐caprolactone was polymerized in the presence of Na‐montmorillonite, the successful ring‐opening polymerization of ?‐caprolactone and the well‐developed exfoliated structure of PCL/Na‐montmorillonite mixture were confirmed. Thereafter, SAN was melt‐mixed with PCL/Na‐montmorillonite nanocomposite, and the SAN matrix and PCL fraction were completely miscible to form a homogeneous mixture with retention of the exfoliated state of Na‐montmorillonite, exhibiting that PCL effectively stabilizes the repulsive polymer–clay interface and contributes to the improvement of the mechanical properties of nanocomposites. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 246–252, 2004     

Separation of ethylene‐propylene copolymers and ethylene‐propylene‐diene terpolymers using high‐temperature interactive liquid chromatography

Ethylene‐propylene‐diene terpolymers (EPDM) are generally amorphous and, therefore, do not crystallize from solution. Consequently, fractionation techniques based on crystallization, such as crystallization analysis fractionation or temperature rising elution fractionation, cannot be used to analyze their chemical composition distribution. Moreover, no suitable chromatographic system was known, which would enable to separate them according to their chemical composition. In this study, two different sorbent/solvent systems are tested with regard to the capability to separate EPDM‐terpolymers and ethylene‐propylene (EP)‐copolymers according to chemical composition. While porous graphite/1‐decanol system is selective towards ethylene and ethylidene‐2‐norbornene, carbon coated zirconia/2‐ethyl‐1‐hexanol is preferentially selective towards ethylene. Consequently, the earlier system enables to separate both EP copolymers and EPDM according to the chemical composition and the latter mainly according to the ethylene content. The results prove that the chromatographic separation in both sorbent/solvent systems is not influenced by molar mass of a sample or by its long chain branching. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Gamma irradiation of high density poly(ethylene)/ethylene‐vinyl acetate/clay nanocomposites: possible mechanism of the influence of clay on irradiated nanocomposites

A further study on mechanical properties and morphology evolution of high density poly (ethylene)/ethylene‐vinyl acetate/and organically‐modified montmorillonite (HDPE/EVA/OMT) nanocomposites exposed to gamma‐rays (0–200 kGy) has been achieved. The results showed that nanocomposites have superior irradiation‐resistant properties to HDPE/EVA blend in mechanical properties. A transmission electron microscope study verified that a face‐face ordered nanostructure had been induced by gamma‐rays. The aim of this paper is to provide a possible mechanism on how the OMT influences the general properties of irradiated nanocomposites, based on the results of thermal, flammability and mechanical behavior. Three facts are postulated to be responsible for the mechanism. The first is the segregation of nano‐dispersed clay layers not only reduces polymer oxidation but prevents crosslinking reactions. The second is the nanostructure evolution induced by gamma‐rays, which may impart nanocomposites improved elasticity. The last is due to the Hofmann degradation, whose degraded products have opposite roles, accelerating polymer oxidation or promoting crosslinking reactions. These facts interact as well as compete with others. The properties of the nanocomposites strongly depended on the prevalent effects developing with increasing irradiation doses. Copyright © 2005 John Wiley & Sons, Ltd.     

Photo‐oxidation of poly(2,6‐dimethyl‐1,4‐phenylene oxide): A reinvestigation

Reinvestigation of poly(2,6‐dimethyl‐1,4‐phenylene oxide) photodegradation at wavelengths > 290 nm shows that both methyl groups and aromatic rings are sites of oxidation with their relative rates dependent on exposure conditions, based on infrared spectroscopy. The methyl group loss is linear with exposure and apparently proceeds by direct abstraction of a benzylic hydrogen by oxygen. The aromatic ring loss and carbonyl growth in the IR spectra appear to be auto‐accelerating and seem to proceed by electron transfer to oxygen, either sensitized or through a direct reaction with oxygen, and recombination of the polymer radical cation and superoxide to result in oxygen addition to the ring. Molecular weight loss in solution occurs to a significant degree only in the presence of oxygen, even in the presence of a hydrogen‐donating solvent, indicating that aryl ether photolysis is not a major pathway. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2318–2331     

Effect of different matrices and nanofillers on the rheological behavior of polymer‐clay nanocomposites

In this work, a comprehensive study of the rheological behavior under shear and isothermal and nonisothermal elongational flow of low density polyethylene (LDPE) and ethylene‐vinyl acetate copolymer (EVA) based nanocomposites was reported to evaluate their “filmability”, that is, the ability of these material to be processed for film forming applications. The influence of two different kinds of organoclay – namely Cloisite 15A and Cloisite 30B – and their concentration was evaluated. The presence of filler clearly affects the rheological behavior in oscillatory state of polyolefin‐based nanocomposites but the increase of complex viscosity and the shear thinning are not dramatic. A larger strain‐hardening effect in isothermal elongational flow is shown by the nanocomposites compared to that of the pure matrix, particularly for EVA based nanocomposites. The melt strength measured under nonisothermal elongational flow increases in the presence of the nanofiller, while the drawability is only slightly lower than that measured for the neat matrix. Moreover, the rheological behavior under nonisothermal elongational flow of EVA‐based nanocomposites is similar for both nanoclays used. Differently, LDPE‐based nanocomposites show a strong dependence on the type of organoclay. Finally, the mechanical properties of the materials were measured by tensile tests. They revealed that the presence of the filler provokes, in all the cases, an increase of the rigidity. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 344–355, 2010     

Radiation effects on styrene–butadiene–ethylene–propylene diene monomer‐multiple walled carbon nanotube nanocomposites: vulcanization and characterization

Varying compositions of styrene–butadiene rubber (SBR) and ethylene–propylene diene monomer (EPDM) 50:50 blend containing multiple walled carbon nanotube (MWNT) as nanoparticulate filler (0.5–5%) were prepared and their efficacy for radiation vulcanization was analyzed by gel‐content, Charlesby‐Pinner parameter, and crosslinking density measurements. Radiation sensitivity of the nanocomposites increased with increase in the MWNT fraction and radiation dose in the dose range studied. The elastic modulus, tensile strength increased with the radiation dose, while elongation at break exhibited downward trend. The extent of reinforcement as assessed using Kraus equation suggested high reinforcement of blend on MWNT addition. The reinforcing mechanism of nanocomposites was studied by various micromechanics models which predicted higher modulus than the experimentally observed results, indicating agglomeration in the nanocomposites. The thermal stability of the composites increased with increase in MWNT loading has been attributed to the antioxidancy induced by nanotubes and higher crosslinking extent of the nanocomposites. Copyright © 2010 John Wiley & Sons, Ltd.     

Influence of hybrid system of nanofillers on the functional properties of postconsumer PET‐G–based nanocomposites

In this article, postconsumer poly (ethylene glycol‐co‐1,4‐cyclohexanedimethanol terephthalate) (PET‐G) foils have been modified with three types of carbon nanofillers that differ in size and shape, ie, multiwalled carbon nanotubes (MWCNTs), graphene nanoplatelets (GNP), and nanosized carbon black (nCB), thus enabling the reusage of recyclate in receiving new functional materials. The series of polymer hybrid nanocomposites have been prepared via a two‐stage polycondensation process, be means of glycolysis of postconsumer PET‐G foil, followed by polycondensation in the presence of carbon nanofillers. The scanning electron microscopy revealed that nanoadditives were uniformly dispersed into the whole volume of polymer matrix. The results present the synergistic effect of hybrid system of nanofillers in improving tensile properties of PET‐G. It has been found that the incorporation of three types of carbon nanofillers has not affected the glass transition temperature of the polymer matrix. Moreover, the incorporation of carbon nanofillers, and the mixture of two, or even three of those, caused an improvement in thermal conductivity and thermal stability.     

The role of thiophosphoryl disulfide on the co‐cure of CR‐EPDM blends

Bis(diisopropyl)thiophosphoryl disulfide (DIPDIS) has been used as a coupling cum curing agent for the compatibilization of blends of ethylene propylene diene monomer rubber (EPDM) with chloroprene rubber (CR). Electrical and mechanical properties of the blend vulcanizates have been studied to find the efficiency of the vulcanizing cum coupling activity of DIPDIS. The study reveals that CR in the presence of DIPDIS greatly improves the physical properties of EPDM. It is noted that the physical properties of the vulcanizates obtained from CR‐EPDM blend depend upon CR:EPDM ratio. The scanning electron microscopy (SEM) study reveals that it is possible to form a coherent blend of CR and EPDM in the presence of DIPDIS. Copyright © 2004 John Wiley & Sons, Ltd.     

The distribution coefficient of oil and curing agent in PP/EPDM TPV

The distribution coefficients of oil and curing agent in PP/EPDM TPV were calculated by measuring the melting point of the PP phase using differential scanning calorimetry (DSC). The PP/EPDM TPV was prepared by using a twin screw extruder and a peroxide curing agent was used. The peroxide induces the degradation of PP, resulting in the decrease of T_m. The oil in PP phase also decreases the Tm. Based on the T_m difference among pure PP and PP/EPDM TPV before and after extraction by cylcohexane, the calculated oil distribution coefficient is 0.537. The addition sequence of PP, oil, and curing agent has a significant effect on the T_m and the calculated curing agent distribution coefficient is 0.52. Both of the coefficients are less than 1. Based on the calculation of the two coefficients, a rationale design of thermoplastic vulcanizate (TPV) can be made by proper control of raw materials, addition sequence, and processing parameters. Copyright © 2007 John Wiley & Sons, Ltd.     

Studies on grafting of tris(2‐methoxyethoxy)vinylsilane onto ethylene‐propylene‐diene terpolymer

New graft copolymer was prepared by incorporating tris(2‐methoxyethoxy)vinylsilane (TMEVS) on ethylene‐propylene‐diene terpolymer (EPDM) by using dicumyl peroxide (DCP) as initiator, in Haake Rheocord 90 torque rheometer. The effect of EPDM concentration, TMEVS concentration, reaction time, reaction temperature and initiator concentration on the graft co polymerization was studied. The grafting efficiency of TMEVS on EPDM was confirmed by Fourier Transform infrared (FT‐IR) spectroscopy. The grafting efficiency increased with increase in the silane concentration upto 6% by weight. The grafting efficiency decreased beyond 6% by weight due to homopolymerization of TMEVS and non‐availability of carbon–carbon double bond in the EPDM terpolymer. The thermal properties of peroxide cured EPDM and hot water cured EPDM‐g‐TMEVS were studied by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) analysis. The results show thermal properties like degradation tempertature and glass transition temperature of the EPDM‐g‐TMEVS were increased due to introduction of TMEVS on to EPDM terpolymer as well as the formation of thermally stable three‐dimensional network. Copyright © 2004 John Wiley & Sons, Ltd.     

Compatibilization level effects on the structure and mechanical properties of rubber‐modified polyamide‐6/clay nanocomposites

Exfoliated polyamide‐6 (PA6)/organically modified montmorillonite clay (OMMT) nanocomposites (PNs) were modified with partially maleinized styrene–ethylene/butadiene–styrene triblock copolymers (SEBS) at three maleinization levels in an attempt to link in these materials high toughness with appropriate small‐strain and fracture tensile properties. OMMT stayed only in the PA6 matrix, and no preferential location in the matrix/rubber interphase was observed. The increased dispersed phase size upon the addition of OMMT was attributed to interactions between maleic anhydride (MA) functionalized SEBS and the surfactant of OMMT. The rubber particle size generally decreased when the MA content of SEBS increased, and this indicated compatibilization. The subsequent good adhesion led to tough nanocomposites across a wide range of both strain rates and fracture modes. As the critical interparticle distance (τ_c) decreased with the MA content, and the other parameters that could influence the surface‐to‐surface mean interparticle distance did not change, it is proposed that in these PNs higher adhesion leads to a smaller τ_c value. Finally, the presence in the matrix of a nanostructured clay makes the rubber content necessary for the toughness jump to increase and τ_c to decrease. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3611–3620, 2005     

Band‐Structure Engineering of ZnO by Anion–Cation Co‐Doping for Enhanced Photo‐Electrochemical Activity

To look for efficient visible light‐driven catalysts for photo‐electrochemical (PEC) water‐splitting, the band structure and optical absorption of monodoped, compensated, and noncompensated n–p pairs of co‐doped bulk ZnO are systemically studied by using both general gradient approximation and hybrid density functional theory approaches (PBE and HSE). Calculations show that n–p co‐doping cannot only enhance the stability that stems from the strong electrostatic attraction between the n‐ and p‐type dopants, but also effectively reduce the band‐gap of ZnO. More importantly, compensated (Ti+C) and noncompensated (Sc+C) and (Cr+C) co‐doped ZnO may be compelling candidates for PEC water‐splitting because of their narrowed band‐gaps, potentially reduced electron–hole recombination centers, appropriate band‐edge positions, enhanced optical absorption, and good stability.     

Great improvement of low‐temperature impact resistance of isotactic polypropylene/ethylene propylene diene monomer rubber blends by traces of carbon nanotubes and β‐nucleating agents

In this work, a considerable low‐temperature toughness enhancement of isotactic polypropylene (iPP) was achieved by adding 30 wt% ethylene propylene diene monomer rubber (EPDM) as well as traces of β‐nucleating agent (β‐NAs) and carbon nanotubes (CNTs). The impact strength of the iPP/30 wt% EPDM blend with 0.1 wt% β‐NAs reached 6.57 kJ/m² at ?20°C, over 2.5 times of pure iPP. A slightly improved impact strength was further found in the β‐nucleated iPP/30 wt% EPDM at the presence of 0.05 wt% CNTs. The presence of traces of CNTs, β‐NAs, and EPDM displayed synergistic low‐temperature toughness reinforcement effect on the iPP blends. The underlying toughening mechanism was attributed to the formation of a great amount of voids and plastic deformation of iPP matrix affected by CNTs, β‐NAs, and EPDM. Our work provided a feasible strategy to significantly increase the low‐temperature toughness of iPP.     

A novel superhydrophobic surface based on low‐density polyethylene/ethylene‐propylene‐diene terpolymer thermoplastic vulcanizate

A novel superhydrophobic surface based on low‐density polyethylene (LDPE)/ethylene‐propylene‐diene terpolymer (EPDM) thermoplastic vulcanizate (TPV) was successfully fabricated where the etched aluminum foil was used as template. The etched aluminum template, consisted of countless micropores and step‐like textures, was obtained by metallographic sandpaper sanding and the subsequent acid etching. The surface morphology and the hydrophobic properties of the molded TPV surface were researched by using field emission scanning electron microscope and contact angle meter, respectively. From the microstructure observation of the superhydrophobic LDPE/EPDM TPV surface, the step‐like textures obtained via molding with etched aluminum foil template and a large number of fiber‐like structures resulted from the plastic deformation of LDPE matrix could be found obviously. The obtained TPV surface exhibited remarkable superhydrophobicity, with a contact angle of 152.0° ± 0.7° and a sliding angle of 3.1° ± 0.8°.     

Gold‐loading magnetic core–shell organic/inorganic nanocomposites: facile preparation and multiple properties

Magnetic composite nanospheres (MCS) were first prepared via mini‐emulsion polymerization. Subsequently, the hybrid core–shell nanospheres were used as carriers to support gold nanoparticles. The as‐prepared gold‐loading magnetic composite nanospheres (Au‐MCS) had a hydrophobic core embed with γ‐Fe₃O₄ and a hydrophilic shell loaded by gold nanoparticles. Both the content of γ‐Fe₃O₄ and the size of gold nanoparticles could be controlled in our experiments, which resulted in fabricating various materials. On one hand, the Au‐MCS could be used as a T₂ contrast agent with a relaxivity coefficient of 362 mg^?1 ml S^?1 for magnetic resonance imaging. On the other hand, the Au‐MCS exhibited tunable optical‐absorption property over a wavelength range from 530 nm to 800 nm, which attributed to a secondary growth of gold nanoparticles. In addition, dynamic light scattering results of particle sizing and Zeta potential measurements revealed that Au‐MCS had a good stability in an aqueous solution, which would be helpful for further applications. Finally, it showed that the Au‐MCS were efficient catalysts for reductions of hydrophobic nitrobenzene and hydrophilic 4‐nitrophenol that could be reused by a magnetic separation process. Copyright © 2014 John Wiley & Sons, Ltd.