Gas solubility of carbon dioxide in poly(lactic acid) at high pressures

The sorption of carbon dioxide in poly(lactic acid) (PLA) was studied by quartz crystal microbalance at high pressures. To address the effect of the D isomer present in the polymer on the gas sorption, measurements were performed in PLA with two different L:D contents, 80:20 and 98:2. New data for the solubility of carbon dioxide in PLA 80:20 and PLA 98:2 over a temperature range from 303.2 to 323.2 K and up to 5 MPa are presented. The results obtained were correlated with the dual‐mode sorption model and the Flory‐Huggins equation. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1010–1019, 2006     

Sorption and partial molar volumes of C2 and C3 hydrocarbons in polypropylene copolymers

The sorption of C₂ and C₃ hydrocarbons in two ethylene–propylene copolymers and a propylene homopolymer and the simultaneous dilation of the polymers were measured at temperatures of 287–363 K and pressures up to 4 MPa. The sorption isotherms were well described by the Flory–Huggins theory of dissolution. Dilation isotherms in the form of elongation versus pressure were similar in shape to the corresponding sorption isotherms. Solubility coefficients, partial molar volumes, and Flory–Huggins interaction parameters were determined from these isotherms. The thermal expansivities of the hydrocarbons dissolved in the polymers were 0.002–0.005 K^?1, and the Flory–Huggins interaction parameters depended not only on temperature but also on concentration. At 323 K, the calculated solubilities of propylene in the ethylene–propylene‐rubber regions of the copolymers were 1.8 times higher than in the amorphous regions of the propylene homopolymer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1255–1262, 2001     

Solubility and partial molar volume of carbon dioxide and ethane in crosslinked poly(ethylene oxide) copolymer

Experimental solubility and sorptive dilation data are reported for carbon dioxide and ethane in a crosslinked poly(ethylene oxide) (XLPEO) rubbery copolymer. Five different temperatures (253 ≤ T(K) ≤ 308) were considered, with a maximum gas pressure of 2.09 MPa (20.6 atm). The polymer was prepared by photopolymerization of a solution containing 70 wt % poly(ethylene glycol) methyl ether acrylate (PEGMEA) and 30 wt % poly(ethylene glycol) diacrylate (PEGDA). Sorption isotherms were described by the Flory‐Huggins model. For each gas, the Flory‐Huggins interaction parameter was a decreasing function of temperature and did not show a composition dependence. Dilation and sorption data were combined to calculate the partial molar volume (PMV) of the gases in the polymer, which was an increasing function of temperature. Based on a comparison with literature data for a XLPEO homopolymer prepared from pure PEGDA over the same range of operating conditions, an effect of the network composition on both gas solubility and PMV was found. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 456–468, 2010     

On the crystallinity effect on the gas sorption in semicrystalline linear low density polyethylene (LLDPE)

This article describes the solubility of carbon dioxide, ethylene and propane in 1‐octene based polyethylene of 0.94, 0.92, 0.904, and 0.87 densities. The isotherms obtained in the gas sorption experimental device display a sorption behavior similar to that of glassy polymers. We apply the dual model to semicrystalline polymers assuming that Henry's sites are related to the amorphous phase, which decreases when the crystallinity percentage increases, whereas the surface of the crystalline phase acts as a Langmuir site with higher gas‐polymer affinity than glassy polymers. The good concordance of the calculated k_D values, using the Flory‐Huggins theory of polymer diluent mixtures, with the experimental results suggest that Henry's gas sorption fulfills this theory and, therefore, it may be a suitable way to estimate polymer‐gas enthalpic interactions. Particularly, the variation of k_D with the crystallinity fraction is exponential and the proportionality of the total sorption with the amorphous content seems only apparent. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1798–1807, 2007     

Light olefins/paraffins sorption in poly(lactic acid) films

The sorption behavior of small molecules like ethane and ethylene in poly (lactic acid) (PLA) was studied in the temperature interval from 283 to 313 K using a Quartz Crystal Microbalance (QCM). The effect of the polymer structure on the solubility selectivity of PLA films with respect to these two gases was studied using polymer with two different L:D ratios (98:2 and 80:20). Furthermore, the polymer films were submitted to different thermal treatments to address the influence of crystallinity and morphology of the noncrystalline fraction on the sorption behavior. The sorption results obtained indicate that ethylene solubility coefficient in annealed PLA 98:2 is about 26% higher than that of ethane and 41% higher in PLA 98:2 melted. The dual‐mode sorption model describes well the sorption isotherms behavior, which is concave concerning the pressure axis. The fully amorphous PLA presents the better selectivity for the studied gases, since the crystallinity seems to produce a negative effect on the selectivity. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1312–1319, 2008     

Basic studies on gas solubility in natural rubber–cellulose composites

This work reports sorption processes of oxygen, carbon dioxide, methane, ethylene, and propylene in films of both vulcanized natural rubber and vulcanized rubber–regenerated cellulose composites. The curves representing the pressure dependence of the concentration of carbon dioxide in the composites clearly exhibit a slight concavity with respect to the abscissa axis as a result of adsorption processes taking place in Langmuir sites located in the glassy cellulose component. Adsorption processes are also detected in the sorption curves of ethylene at low pressures. The concavity with respect to the ordinate axis of the curve concentration of propylene versus pressure at high pressure is pretty well described by the Flory‐Huggins formalism. The solubilities of the other gases mainly obey Henry's behavior, adsorption processes in the glassy component being in most cases negligible. Values of the interaction χ parameter for gas–natural rubber and gas–natural rubber composites are obtained from the comparison of the experimental solubility coefficients with those predicted by the Flory‐Huggins theory. The theory suggests that Henry's constant is a linear function of the boiling temperature of the gases. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2131–2140, 2005     

Simultaneous measurement of the solubility of nitrogen and carbon dioxide in polystyrene and of the associated polymer swelling

New experimental results for the solubility of nitrogen and carbon dioxide in polystyrene are reported, accompanied by data on the change in volume of the polymer caused by the sorption process. The two phenomena were measured simultaneously with a combined technique, in which the quantity of penetrating fluid introduced into the system was evaluated by pressure‐decay measurements in a calibrated volume, whereas a vibrating‐wire force sensor was employed for weighing the polymer sample during sorption inside of the high‐pressure equilibrium cell. The use of the two techniques was necessary because the effects of swelling and solubility could not be decoupled in a single gravimetric or pressure‐decay measurement. The sorption of nitrogen in polystyrene was studied along three isotherms from 313 to 353 K at pressures up to 70 MPa. The sorption of carbon dioxide was measured along four isotherms from 338 to 402 K up to 45 MPa. The results are compared with values from the literature when possible, although our data extend significantly the pressure ranges of the latter. The uncertainties affecting our measurements with nitrogen are 1 mg of N₂/g of polystyrene in solubility and 0.1% of the volume of the polymer. For carbon dioxide, the uncertainties are 5 mg of N₂/g of polystyrene and 0.5% respectively, carbon dioxide being about 1 order of magnitude more soluble than nitrogen. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2063–2070, 2001     

Solubility and diffusivity of methylmethacrylate and butylacrylate monomers in a MMA–BA copolymer

Mutual diffusion coefficients and sorption isotherms of methyl methacrylate (MMA) and butyl acrylate (BA) monomers in methyl methacrylate‐butyl acrylate copolymer (MMA‐BA) have been measured by gravimetric sorption. MMA is found to have higher solubility and diffusion rates in the copolymer than BA. Sorption data for MMA were interpreted using classical Flory‐Huggins thermodynamic theory with a constant interaction parameter (χ). A modified version of this theory has been applied to correlate the sorption data of BA, which exhibit a temperature and concentration‐dependent χ parameter. For MMA, the isotherm data reveal enhanced polymer‐solvent interactions with increasing temperature, while for BA the data indicate a drive toward phase separation with increasing temperature. Despite the difference in thermodynamic behavior, both monomers are found to exhibit Fickian diffusion and the diffusivity data are correlated reasonably well with the Vrentas‐Duda free volume theory. Some deviation between the free‐volume correlation and the experimental data is observed at the lowest temperature and BA concentration examined. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1996–2006, 2007     

Polymer modification using difluoromethane (HFC 32) and carbon dioxide

The infusion of difluoromethane (HFC 32) and CO₂ into polystyrene and polyethylene has been characterized using a quartz crystal microbalance technique over a range of temperatures and pressures. The results were adequately modeled by Flory‐Huggins theory. Significant plasticization was observed in the polymeric materials and it is shown that manipulation of the experimental temperature, pressure, and rate of depressurisation can cause significant changes in the morphology of the samples. It is demonstrated for the first time how rate constant data for the kinetics of gas sorption can be extracted quickly and easily from in situ quartz crystal microbalance measurements. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1072–1083, 2006     

Kinetics of the volume phase transition in poly(n‐isopropylacrylamide) gels prepared under high pressure

New poly(N‐isopropylacrylamide) gels were prepared under high pressure (ca. 200 MPa) during gelation. The preparation‐pressure dependence of the deswelling speed of the gels was measured with a conventional T‐jump method. The deswelling time of a gel rod 2.2 mm in diameter prepared at 193 MPa was about 200 s, 1000 times faster than that of a homogeneous poly(N‐isopropylacrylamide) gel. Moreover, the collective diffusion coefficient, the thermal fluctuation, and the ensemble‐average intensity of the swollen gel networks were obtained with dynamic light scattering measurements. Both the enthalpy and entropy of the gels were estimated from equilibrium swelling curves with the Flory–Huggins interaction parameter evaluated with mean field theory based on the Flory‐type of the Gibbs free‐energy formula. It was found that the networks of the gels had an inhomogeneous structure newly introduced by the preparation pressure. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2315–2325, 2001     

Carbon dioxide, ethylene and water vapor sorption in poly(lactic acid)

The objective of this work is to study the gas/vapor sorption in poly(lactic acid) (PLA) with a 98:2 (l:d) ratio using a quartz crystal microbalance (QCM). For that purpose, the sorption of carbon dioxide, ethylene and water vapor in poly(lactic acid) (PLA) with a 98:2 (l:d) ratio, in temperature range from 283 to 313 K and up to atmospheric pressure was measured. The measured isotherms indicate that the sorption mechanism is sorbate dependent, since carbon dioxide and ethylene seem to have predominantly a Langmuir type of mechanism while water is predominantly Henry controlled. Two temperature protocols were used and only ethylene sorption is affected by them. Comparisons with previously measured gas sorption data in PLA 80:20 using the same temperature protocol indicate that the l:d ratio plays a dominant role in gas/vapor sorption in PLA.     

Inverse gas chromatographic characterization of triblock copolymer of polystyrene–poly(ethylene oxide)–polystyrene

The thermodynamic properties of triblock copolymer of polystyrene–poly (ethylene oxide)–polystyrene (PS‐b‐PEO‐b‐PS) were investigated by means of inverse gas chromatography (IGC) using 15 different kinds of solvents as the probes. Some thermodynamic parameters, such as specific retention volume, molar heats of sorption, weight fraction activity coefficient, Flory‐Huggins interaction parameter, partial molar heats of mixing and solubility parameter were obtained to judge the interactions between PS‐b‐PEO‐b‐PS polymers and solvents and the solubility of the polymers in these solvents. It was found that increasing PEO content in PS‐b‐PEO‐b‐PS resulted in the increase in the solubility of PS‐b‐PEO‐b‐PS in alkanes and acetates solvents, but the solubility in alcohols had no change, and more PEO content in polymer caused a small decrease in the solubility parameter of PS‐b‐PEO‐b‐PS polymer, © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2015–2022, 2007     

Investigation of polymer–solvent interactions in poly(styrene sulfonate) thin films

The swelling behavior of acid form poly(styrene sulfonate) (PSS‐H) thin films were investigated using in situ spectroscopic ellipsometry (SE) to probe the polymer–solvent interactions of ion‐containing polymers under interfacial confinement. The interaction parameter (χ), related to the polymer and solvent solubility parameters in the Flory–Huggins theory, describes the polymer‐solvent compatibility. In situ SE was used to measure the degree of polymer swelling in various solvent vapor environments, to determine χ for the solvent‐PSS‐H system. The calculated solubility parameter of 40–44 MPa^1/2 for PSS‐H was determined through measured χ values in water, methanol, and formamide environments at a solvent vapor activity of 0.95. Flory–Huggins theory was applied to describe the thickness‐dependent swelling of PSS‐H and to quantify the water‐PSS‐H interactions. Confinement had a significant influence on polymer swelling at low water vapor activities expressed as an increased χ between the water and polymer with decreasing film thickness. As the volume fraction of water approached ～0.3, the measured χ value was ～0.65, indicating the water interacted with the polymer in a similar manner, regardless of thicknesses. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1365–1372     

Sorption of methanol/MTBE and diffusion of methanol in 6FDA–ODA polyimide

This article discusses the diffusion and solubility behavior of methanol/methyl tert‐butyl ether (MTBE) in glassy 6FDA–ODA polyimide prepared from hexafluoroisopropylidene 2,2‐bis(phthalic anhydride) (6FDA) and oxydianiline (ODA). The diffusion coefficients and sorption isotherm of methanol vapor in 6FDA–ODA polyimide at various pressures and film thicknesses were obtained with a McBain‐type vapor sorption apparatus. Methanol/MTBE mixed‐liquid sorption isotherms were obtained by head‐space chromatography and compared with a pure methanol sorption isotherm obtained with a quartz spring balance. Methanol sorption isotherms obtained with the two methods were almost identical. Both methanol sorption isotherms obeyed the dual‐mode model at a lower activity, which is typical for glassy polymer behavior. The MTBE was readily sorbed into the polymer in the presence of methanol, but the MTBE sorption isotherm exhibited a highly nonideal behavior. The MTBE sorption levels were a strong function of the methanol sorption level. Methanol diffusion in the polymer was analyzed in terms of the partial immobilization model with model parameters obtained from average diffusion coefficients and the dual‐mode sorption parameters. Simple average diffusion coefficients were obtained from sorption kinetics experiments, whereas the dual‐mode sorption parameters were obtained from equilibrium methanol sorption experiments. An analysis of the mobility and solubility data for methanol indicated that methanol tends to form clusters at higher sorption levels. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2254–2267, 2000     

Sorption and partial molar volume of gases in poly (dimethyl siloxane)

Sorption of N₂, O₂, Ar, CH₄, CO₂, C₂H₄, and C₂H₆ in poly (dimethyl siloxane) liquid and rubber and the dilation of the polymers due to sorption of the gases are studied at 25°C under pressures up to 50 atm. In the liquid, the sorption isotherms for low-solubility and high-solubility gases are described by Henry's law and the Flory–Huggins equation, respectively. Gas sorption in the rubber, which contains a 29 wt % silica filler, follows the dual-mode sorption model, though marked hysteresis is observed in the sorption of O₂ and CH₄. The dilation isotherms increase linearly or exponentially in both polymers with increasing pressure. Considering that gas molecules adsorbed into micropores of the filler particles do not participate in the dilation, partial molar volumes of the dissolved gases in the rubber are determined from data of sorption and dilation. The values are nearly equal to the partial molar volumes in the liquid (48–60 cm³/mol).     

Separation studies of hydrazine from aqueous solutions by pervaporation

Separation of hydrazine from aqueous solutions with ethylcellulose membranes has been investigated by using the pervaporation technique. The effect of membrane thickness, concentration polarization, and feed concentration on flux and selectivity were evaluated. A separation mechanism is proposed based on the measurements of sorption, and diffusion coefficients, and estimations of Flory–Huggins interaction parameters and Hansen's solubility parameter. States of water, hydrazine, and hydrazine hydrate are explained with DSC spectra. The specific interaction sites in ethylcellulose matrix where the solvent interacts extensively with the polymer have been identified by FTIR analysis. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1969–1980, 1999     

Transport of hexane vapor in polystyrene at 25°C I. Analysis of integral sorption data

A series of measurements of integral n-hexane vapor sorption at 25°C and moderate activity, in polystyrene microspheres of varying radii, exhibits typical non-Fickian behavior: nonoverlap of curves of fractional uptake versus (square root of time)/radius. The data are examined in light of a sorption isotherm indicating hexane solubility in excess of that predicted by the Flory–Huggins equation, up to the hexane activity at which the glass transition apparently occurs. A transport analysis is developed based on the assumption that below the transition temperature T_g the rate of sorption is limited by the rate of polymer chain relaxations induced by the penetrant, which facilitate hexane entry into, and immobilization in, glassy microvoids.     

Evaluation of gas sorption parameters and prediction of sorption isotherms in glassy polymers

A model of continuous‐site distribution for gas sorption in glassy polymers is examined with sorption data of CO₂ and Ar in polycarbonate. A procedure is presented for determining from a measured isotherm the number of sorption sites in a polymer, an important parameter that previously had to be assumed. With this parameter value and solubility data obtained at zero pressure, the model can reasonably predict sorption isotherms of CO₂ in glassy polycarbonate for a wide temperature range. The number of sorption sites and the average site volume evaluated from CO₂ sorption isotherms are employed for the prediction of Ar sorption isotherms with zero‐pressure solubility data and the independently measured partial molar volume of Ar. A reasonable fit to the measured isotherms of Ar is achieved. With the proposed procedure, the continuous‐site model shows several advantages over the conventional dual‐mode sorption model. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 883–888, 2000     

Sorption and transport of linear alkane hydrocarbons in biaxially oriented polyethylene terephthalate

Equilibrium sorption and uptake kinetics of n‐butane and n‐pentane in uniform, biaxially oriented, semicrystalline polyethylene terephthalate films were examined at 35 °C and for pressures ranging from 0 to approximately 76 cmHg. Sorption isotherms were well described by the dual‐mode sorption model. Sorption kinetics were described either by Fickian diffusion or a two‐stage model incorporating Fickian diffusion at short times and protracted polymer structural relaxation at long times. Diffusion coefficients increased with increasing penetrant concentration. n‐Butane solubility was lower than that of n‐pentane, consistent with the more condensable nature of n‐pentane. However, n‐butane diffusion coefficients were higher than those of n‐pentane. Infinite‐dilution, estimated amorphous phase diffusion and solubility coefficients were well correlated with penetrant critical volume and critical temperature, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 1160–1172, 2001     

Gas sorption,diffusion, and permeation in poly(dimethylsiloxane)

The permeability of poly(dimethylsiloxane) [PDMS] to H₂, O₂, N₂, CO₂, CH₄, C₂H₆, C₃H₈, CF₄, C₂F₆, and C₃F₈, and solubility of these penetrants were determined as a function of pressure at 35 °C. Permeability coefficients of perfluorinated penetrants (CF₄, C₂F₆, and C₃F₈) are approximately an order of magnitude lower than those of their hydrocarbon analogs (CH₄, C₂H₆, and C₃H₈), and the perfluorocarbon permeabilities are significantly lower than even permanent gas permeability coefficients. This result is ascribed to very low perfluorocarbon solubilities in hydrocarbon‐based PDMS coupled with low diffusion coefficients relative to those of their hydrocarbon analogs. The perfluorocarbons are sparingly soluble in PDMS and exhibit linear sorption isotherms. The Flory–Huggins interaction parameters for perfluorocarbon penetrants are substantially greater than those of their hydrocarbon analogs, indicating less favorable energetics of mixing perfluorocarbons with PDMS. Based on the sorption results and conventional lattice solution theory with a coordination number of 10, the formation of a single C₃F₈/PDMS segment pair requires 460 J/mol more energy than the formation of a C₃H₈/PDMS pair. A breakdown in the geometric mean approximation of the interaction energy between fluorocarbons and hydrocarbons was observed. These results are consistent with the solubility behavior of hydrocarbon–fluorocarbon liquid mixtures and hydrocarbon and fluorocarbon gas solubility in hydrocarbon liquids. From the permeability and sorption data, diffusion coefficients were determined as a function of penetrant concentration. Perfluorocarbon diffusion coefficients are lower than those of their hydrocarbon analogs, consistent with the larger size of the fluorocarbons. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 415–434, 2000