Simultaneous introduction of phosphonic and carboxylic acid functions to hydroxylated macromolecules

Novel diblock and dihydrophilic ionic–nonionic copolymers, having phosphonic and carboxylic functions at the same carbon atom in the repeating units of the ionic block, were prepared. The addition of 2-diethylphosphono-ethyl acrylate (PC) to hydroxyl groups of the polyglycidol block of the poly(ethylene glycol)-b-polyglycidol block copolymer was followed by the dealkylation of phosphonic acid esters and the hydrolysis of carboxylic acid esters. The polymer was characterized by ¹H, ¹³C, and ³¹P NMR. The kinetics of the PC addition and the hydrolysis of the ethyl carboxylate function were also studied, and a simple bimolecular second-order reaction was established. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 432–443, 2004     

Synthesis of a novel liquid crystal rod–coil star block copolymer consisting of poly(methyl methacrylate) and poly{2,5‐bis[(4‐methoxy‐phenyl)oxycarbonyl] styrene} via atom transfer radical polymerization

A bromine capped star‐shaped poly(methyl methacrylate) (S‐PMMA‐Br) was synthesized with CuBr/sparteine/PT‐Br as a catalyst and initiator to polymerize methyl methacrylate (MMA) according to atom transfer radical polymerization (ATRP). Then, with S‐PMMA‐Br as a macroinitiator, a series of new liquid crystal rod–coil star block copolymers with different molecular weights and low polydispersity were obtained by this method. The block architecture {coil‐conformation of the MMA segment and rigid‐rod conformation of 2,5‐bis[(4‐methoxyphenyl)oxycarbonyl] styrene segment} of the four‐armed rod–coil star block copolymers were characterized by ¹H NMR. The liquid‐crystalline behavior of these copolymers was studied by differential scanning calorimetry and polarized optical microscopy. We found that the liquid‐crystalline behavior depends on the molecular weight of the rigid segment; only the four‐armed rod–coil star block copolymers with each arm's M_n,_GPC of the rigid block beyond 0.91 × 10⁴ g/mol could form liquid‐crystalline phases above the glass‐transition temperature of the rigid block. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 733–741, 2005     

Dihydrophilic block copolymers with ionic and nonionic blocks. I. Poly(ethylene oxide)‐b‐polyglycidol with OP(O)(OH)2, COOH,or SO3H functions: Synthesis and influence for CaCO3 crystallization

Dihydrophilic block copolymers of poly(ethylene oxide)‐b‐polyglycidol were prepared and polyglycidol blocks converted into ionic blocks containing  OP(O)(OH)₂,  COOH, or  SO₃H groups. Although phosphorylation of polyhydroxy compounds with POCl₃ usually leads to insoluble products, phosphorylation of poly(ethylene oxide)‐b‐polyglycidol using a POCl₃/ OH ratio equal to 1/1 gave soluble products, predominantly monoester of phosphoric acid (after hydrolysis) (provided that the reaction was conducted in triethyl phosphate as solvent). All copolymers were characterized by ¹H NMR, ¹³C NMR, and/or ³¹P NMR spectra for confirming their structure. The degree of substitution was determined from quantitative ¹³C NMR spectroscopy (inverted‐gate decoupling‐acquisition mode). Preliminary results indicate that from these three groups of block copolymers the phosphoric acid esters are the most effective ones at least in controlling the growth of CaCO₃ crystals in aqueous solution. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 955–963, 2001     

Synthesis,characterization, and self‐assembly of comb‐dendronized amphiphilic block copolymers

Novel amphiphilic comb‐dendronized diblock copolymers composed of hydrophobic Percec‐type dendronized polystyrene block and hydrophilic comb‐like poly(ethylene oxide) grafted polymethacrylate P(PEOMA) block were designed and synthesized via two steps of atom transfer radical polymerization (ATRP). The comb‐like P(PEOMA) prepared by ATRP of macromonomers (PEOMA) with two different molecular weights (M_n = 300 and 475) were used to initiate the sequent ATRP of dendritic styrene macromonomer (DS). The molecular weights and compositions of the obtained block copolymers were determined by ¹H NMR analysis. The copolymers with relatively narrow polydispersities (1.27–1.38) were thus obtained. The bulk properties of comb‐dendronized block copolymers were studied by using differential scanning calorimetry, polarized optical microscopy and wide‐angle X‐ray diffraction (WAXD). Similar to dendronized homopolymers, the block copolymers exhibited hexagonal columnar liquid‐crystalline phase structure. By using such amphiphilic comb‐dendronized block copolymers as building blocks, the rich self‐assembly morphologies, such as twisted string, vesicle, and large compound micelle (LCM), were obtained in a mixture of CH₃OH and THF. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4205–4217, 2008     

Self‐assembly of oligo(p‐phenylenevinylene)‐block‐poly(ethylene oxide) in polar media and solubilization of an oligo(p‐phenylenevinylene) homooligomer inside the assembly

Rod–coil amphiphilic diblock copolymers, consisting of oligo(p‐phenylenevinylene) (OPV) as a rod and hydrophobic block and poly(ethylene oxide) (PEO) as a coil and hydrophilic block, were synthesized by a convergent method. The aggregation behavior of the block copolymers in a selective solvent (tetrahydrofuran/H₂O) was probed with the absorption and emission of the OPV block. With increasing H₂O concentration, the absorption maximum was blueshifted, the emission from the molecularly dissolved OPV decreased, and that from the aggregated OPV increased. This indicated that the OPV blocks formed H‐type aggregates in which the OPV blocks aligned in a parallel orientation with one another. The transmission electron microscopy observation revealed that the block copolymers with PEO weight fractions of 41 and 62 wt % formed cylindrical aggregates with a diameter of 6–8 nm and a length of several hundreds nanometers, whereas the block copolymer with 79 wt % PEO formed distorted spherical aggregates with an average diameter of 13 nm. Furthermore, the solubilization of an OPV homooligomer with the block copolymer was studied. When the total polymer concentration was less than 0.1 wt %, the block copolymer solubilized OPV with a 50 mol % concentration. The structure of the aggregates was a cylinder with a relatively large diameter distribution. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1569–1578, 2005     

Disulfide‐centered star‐shaped polypeptide‐PEO block copolymers for reduction‐triggered drug release

Disulfide‐centered star‐shaped poly(ε‐benzyloxycarbonyl‐l ‐lysine)‐b‐poly(ethylene oxide) block copolymers (i.e., A₂B₄ type Cy‐PZlys‐b‐PEO) were synthesized by the combination of ring‐opening polymerization and thiol‐yne chemistry. Their molecular structures and physical properties were characterized in detail by FTIR, ¹H NMR, gel permeation chromatography, differential scanning calorimetry, wide‐angle X‐ray diffraction, and polarized optical microscope. Despite mainly exhibiting an α‐helix conformation, the inner PZlys blocks within copolymers greatly prohibited the crystallinity of the outer PEO blocks and presented a liquid crystal phase transition behavior in solid state. These block copolymers Cy‐PZlys‐b‐PEO self‐assembled into nearly spherical micelles in aqueous solution, which had a hydrophobic disulfide‐centered PZlys core surrounded by a hydrophilic PEO corona. As monitored by means of DLS and TEM, these micelles were progressively reduced to smaller micelles in 10 mM 1,4‐dithiothreitol at 37 °C and finally became ones with a half size, demonstrating a reduction‐sensitivity. Despite a good drug‐loading property, the DOX‐loaded micelles of Cy‐PZlys‐b‐PEO exhibited a reduction‐triggered drug release profile with an improved burst‐release behavior compared with the linear counterpart. Importantly, this work provides a versatile strategy for the synthesis of the disulfide‐centered star‐shaped polypeptide block copolymers potential for intracellular glutathione‐triggered drug delivery systems. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2000–2010     

Azobenzene‐Containing Block Copolymers as Light‐Induced Reworkable Adhesives: Effects of Molecular Weight,Composition, and Block Copolymer Architectures on the Adhesive Properties

We previously reported that ABA‐type triblock copolymers with azobenzene‐containing terminal blocks can be utilized as a light‐induced reworkable adhesive that enables repeatable bonding and debonding on demand. The reworkability was based on the photoisomerization of the azobenzene moiety and concomitant softening and hardening of the azo blocks. Our aim in this study is to investigate the effect of the composition, molecular weight, and block copolymer architectures on the reworkable adhesive properties. For this purpose, we prepared AB diblock, ABA triblock, and 4‐arm (AB)₄ star‐block copolymers consisting of polymethacrylates bearing an azobenzene moiety (A block) and 2‐ethylhexyl (B block) side chains and performed adhesion tests by using these block copolymers. As a result, among the ABA block copolymers with varied compositions and molecular weights, the ABA triblock copolymers with an azo block content of about 50 wt % and relatively low molecular weight could achieve an appropriate balance between high adhesion strength and low residual adhesion strength upon UV irradiation. Furthermore, the 4‐arm star‐block structure not only enhances the adhesion strength, but also maintains low residual adhesion strength when exposed to UV irradiation. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 806–813     

Reversible melting in nanophase‐separated poly(oligoamide‐alt‐oligoether)s and its dependence on sequence length,crystal perfection,and molecular mobility

The degree of reversibility of the melting of multiblock copolymers of alternating oligoamides and oligoethers was investigated with respect to the composition and molecular mass of the blocks. The analysis was conducted with temperature‐modulated calorimetry, and it revealed different degrees of reversibility of the melting process that depended on the block length, crystal perfection, and molecular mobility. For the oligoamide blocks, the amount of crystal that melts and crystallizes reversibly during quasi‐isothermal analysis increases with decreasing molar mass, and shorter amide sequences form poorer crystals that have a higher tendency toward reorganization. Reorganization of the oligoamides is also favored by the presence of the more mobile oligoether units. Reversible melting of the oligoether segments is influenced by the presence of glassy and crystalline oligoamide blocks in the adjacent nanophases. Because of the segmented nature of the copolymers, the oligoether segments are not free to flow as in an isotropic melt but are anchored to the oligoamide surfaces with different degrees of restriction that change the local equilibrium of melting and recrystallization. A comparison of the copolymers with the corresponding homopolymers provides information about the role of molecular nucleation and mobility in the reversibility of melting. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2969–2981, 2001     

One‐pot synthesis of conjugated poly(3‐hexylthiophene)‐b‐poly(phenyl isocyanide) hybrid rod–rod block copolymers and its self‐assembling properties

In this article, the synthesis of a series of conjugated rod–rod block copolymers based on poly(3‐hexylthiophene) (P3HT) and poly(phenyl isocyanide) (PPI) building blocks in a single pot is presented. Ni‐catalyzed Grignard metathesis polymerization of 2,5‐dibromo‐3‐hexylthiophene and subsequent addition of 4‐isocyanobenzoyl‐2‐aminoisobutyric acid decyl ester in the presence of Ni(dppp)Cl₂ as a single catalyst afford P3HT‐b‐PPI with tunable molecular weights and compositions. In solid state, microphase separation occurred as differential scanning calorimetric analysis of P3HT‐b‐PPI revealed two glass transition temperatures. In solutions, the copolymers can self‐assemble into spherical aggregates with P3HT core and PPI shell in tetrahydrofuran and exhibit amorphous state in CHCl₃. However, atomic force microscopy revealed that the block copolymers self‐assemble into nanofibrils on the substrate. These unique features warrant the resultant conjugated rod–rod copolymers' potential study in organic photovoltaic and other electronic devices. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2939–2947     

A–B–A stereoblock copolymers of N‐isopropylacrylamide

A–B–A stereoblock polymers with atactic poly(N‐isopropylacrylamide) (PNIPAM) as a hydrophilic block (either A or B) and a non‐water‐soluble block consisting of isotactic PNIPAM were synthesized using reversible addition fragmentation chain transfer (RAFT) polymerizations. Yttrium trifluoromethanesulfonate was used in the tacticity control, and bifunctional S,S′‐bis(α,α′‐dimethyl‐α″‐acetic acid)‐trithiocarbonate (BDAT) was utilized as a RAFT agent. Chain structures of the A–B–A stereoblock copolymers were determined using ¹H NMR, SEC, and MALDI‐TOF mass spectrometry. BDAT proved to be an efficient RAFT agent in the controlled synthesis of stereoregular PNIPAM, and both atactic and isotactic PNIPAM were successfully used as macro RAFT agents. The glass transition temperatures (T_g) of the resulting polymers were measured by differential scanning calorimetry. We found that the T_g of isotactic PNIPAM is molecular weight dependent and varies in the present case between 115 and 158 °C. Stereoblock copolymers show only one T_g, indicating the miscibility of the blocks. Correspondingly, the T_g may be varied by varying the mutual lengths of the A and B blocks. The phase separation of aqueous solutions upon increasing temperature is strongly affected by the isotactic blocks. At a fixed concentration (5 mg/mL), an increase of the isotacticity of the stereoblock copolymers decreases the demixing temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 38–46, 2008     

Synthesis and characterization of well‐defined [polystyrene‐b‐poly(2‐vinylpyridine)]n star‐block copolymers with poly(2‐vinylpyridine) corona blocks

This article describes the synthesis and characterization of [polystyrene‐b‐poly(2‐vinylpyridine)]_n star‐block copolymers with the poly(2‐vinylpyridine) blocks at the periphery. A two‐step living anionic polymerization method was used. Firstly, oligo(styryl)lithium grafted poly(divinylbenzene) cores were used as multifunctional initiators to initiate living anionic polymerization of styrene in benzene at room temperature. Secondly, vinylpyridine was polymerized at the periphery of these living (polystyrene)_n stars in tetrahydrofuran at ?78 °C. The resulting copolymers were characterized using size exclusion chromatography, multiangle laser light scattering, ¹H NMR, elemental analysis, and intrinsic viscosity measurements. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3949–3955, 2007     

Controlled ring‐opening polymerization of L‐lactide and 1,5‐dioxepan‐2‐one forming a triblock copolymer

Novel elastomeric A‐B‐A triblock copolymers were successfully synthesized in a new two‐step process: controlled ring‐opening polymerization of the cyclic ether–ester 1,5‐dioxepan‐2‐one as the amorphous middle block (B‐block) followed by addition and polymerization of the two semicrystalline L ‐lactide blocks (A‐block). A 1,1,6,6‐tetra‐n‐butyl‐1,6‐distanna‐2,5,7,10‐tetraoxacyclodecane initiator system was utilized and the reaction was performed in chloroform at 60 °C. A good control of the synthesis was obtained, resulting in well defined triblock copolymers. The molecular weight and chemical composition were easily adjusted by the monomer‐to‐initiator ratio. The triblock copolymers formed exhibited semicrystallinity up to a content of 1,5‐dioxepan‐2‐one as high as 89% as determined by differential scanning calorimetry. WAXS investigation of the triblock copolymers showed a crystal structure similar to that of the pure poly(L ‐lactide). © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1774–1784, 2000     

The synthesis and self‐assembly of ABA amphiphilic block copolymers containing styrene and oligo(ethylene glycol) methyl ether methacrylate in dilute aqueous solutions: Elevated cloud point temperatures for thermoresponsive micelles

A series of ABA amphiphilic triblock copolymers possessing polystyrene (PS) central hydrophobic blocks, one group with “short” PS blocks (DP = 54–86) and one with “long” PS blocks (DP = 183–204) were synthesized by atom transfer radical polymerization. The outer hydrophilic blocks were various lengths of poly(oligoethylene glycol methyl ether) methacrylate, a comb‐like polymer. The critical aggregation concentrations were recorded for certain block copolymer samples and were found to be in the range circa 10⁻⁹ mol L⁻¹ for short PS blocks and circa 10⁻¹² mol L⁻¹ for long PS blocks. Dilute aqueous solutions were analyzed by transmission electron microscopy (TEM) and demonstrated that the short PS block copolymers formed spherical micelles and the long PS block copolymers formed predominantly spherical micelles with smaller proportions of cylindrical and Y‐branched cylindrical micelles. Dynamic light scattering analysis results agreed with the TEM observations demonstrating variations in micelle size with PS and POEGMA chain length: the hydrodynamic diameters (D_H) of the shorter PS block copolymer micelles increased with increasing POEGMA block lengths while maintaining similar PS micellar core diameters (D_C); in contrast the values of D_H and D_C for the longer PS block copolymer micelles decreased. Surface‐pressure isotherms were recorded for two of the samples and these indicated close packing of a short PS block copolymer at the air–water interface. The aggregate solutions were demonstrated to be stable over a 38‐day period with no change in aggregate size or noticeable precipitation. The cloud point temperatures of certain block copolymer aggregate solutions were measured and found to be in the range 76–93 °C; significantly these were ∼11 °C higher in temperature than those of POEGMA homopolymer samples with similar chain lengths. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7739–7756, 2008     

Encapsulation and release by star‐shaped block copolymers as unimolecular nanocontainers

A five‐arm star‐shaped poly(ethylene oxide) (PEO) with terminal bromide groups was used as a macroinitiator for the atom transfer radical polymerization of tert‐butyl acrylate (tBA), resulting in five‐arm star‐shaped poly(ethylene oxide)‐block‐poly(tert‐butyl acrylate) block copolymers. The polymerization proceeded in a controlled way using a copper(I)bromide/pentamethyl diethylenetriamine catalytic system in acetonitrile as solvent. The hydrolysis of the tBA blocks of the amphiphilic star‐shaped PEO‐b‐PtBA block copolymer resulted in dihydrophilic star structures. The encapsulation of the star‐block copolymers and their release properties in acid environment have been followed by UV‐spectroscopy and color changes, using the dye methyl orange as a hydrophilic guest molecule. Characterization of the structures has been done by ¹H NMR, size exclusion chromatography, MALDI‐TOF, and differential scanning calorimetry. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 650–660, 2008     

Amphiphilic dendritic copolymers of tert‐butyl‐glycidylether and glycidol as a nanocontainer for an anticancer ruthenium complex

Dendritic copolymers comprising a hydrophobic core and hydrophilic shell with nearly equal numbers of hydroxyl groups in the shell and different densities in the core were prepared by a multi‐step process based on anionic ring‐opening polymerization. The diversity in the core density was obtained by using copolymer stars with poly(tert‐butyl‐glycidylether)‐block‐polyglycidol arms with nearly equal length of hydrophobic blocks and numbers of hydroxyl groups of polyglycidol but different numbers of arms as macroinitiators. The ability of the dendritic copolymers to serve as a nanocontainer for a ruthenium complex Ru(NH₃)₃Cl₃ with anticancer properties was studied. The possibility of improving the water solubility of this poorly soluble drug by loading it onto dendritic copolymers was investigated. The hydroxyl groups of the dendritic copolymers were used for complexation of the ruthenium compound to the shell. The loading efficiency was analyzed by UV–vis spectroscopy. The dendritic nanoparticles in their hydrated state were visualized using cryo‐TEM. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3488–3497     

Synthesis and self‐association behavior of poly[bis(2‐(2‐methoxyethoxy)ethoxy)phosphazene]‐b‐poly(propyleneglycol) triblock copolymers

Amphilic triblock copolymers with varying ratios of hydrophilic poly[bis (methoxyethoxyethoxy)phosphazene] (MEEP) and relatively hydrophobic poly(propylene glycol) (PPG) blocks were synthesized via the controlled cationic‐induced living polymerization of a phosphoranimine (Cl₃P?NSiMe₃) at ambient temperature. A PPG block can function as either a classical hydrophobic block or a less hydrophobic component by varying the nature of a phosphazene block. The aqueous phase behavior of MEEP‐PPG‐MEEP block copolymers was investigated using fluorescence techniques, TEM, and dynamic light scattering (DLS). The critical micelle concentrations (cmcs) of MEEP‐PPG‐MEEP block copolymers were determined to be in the range of 3.7–16.8 mg/L. The mean diameters of MEEP‐PPG‐MEEP polymeric micelles, measured by DLS, were between 31 and 44 nm. The equilibrium constants of pyrene in these micelles ranged from 4.7 × 10⁴ to 9.6 × 10⁴. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 692–699, 2009     

Fluorinated block copolymers containing poly(vinylidene fluoride) or poly(vinylidene fluoride‐co‐hexafluoropropylene) blocks from perfluoropolyethers: Synthesis and thermal properties

PFPE‐b‐PVDF and PFPE‐b‐poly(VDF‐co‐HFP) block copolymers [where PFPE, PVDF, VDF, and HFP represent perfluoropolyether, poly(vinylidene fluoride), vinylidene fluoride (or 1,1‐difluoroethylene), and hexafluoropropylene] were synthesized by radical (co)telomerizations of VDF (or VDF and HFP) with an iodine‐terminated perfluoropolyether (PFPE‐I). Di‐tert‐butyl peroxide (DTBP) was used and was shown to act as an efficient thermal initiator. The numbers of VDF and VDF/HFP base units in the block copolymers were assessed with ¹⁹F NMR spectroscopy. According to the initial [PFPE‐I]₀/[fluoroalkenes]₀ and [DTBP]₀/[fluoroalkenes]₀ molar ratios, fluorinated block copolymers of various molecular weights (1500–30,300) were obtained. The states and thermal properties of these fluorocopolymers were investigated. The compounds containing PVDF blocks with more than 30 VDF units were crystalline, whereas all those containing poly(VDF‐co‐HFP) blocks exhibited amorphous states, whatever the numbers were of the fluorinated base units. All the samples showed negative glass‐transition temperatures higher than that of the starting PFPE. Interestingly, these PFPE‐b‐PVDF and PFPE‐b‐poly(VDF‐co‐HFP) block copolymers exhibited good thermostability. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 160–171, 2003     

Facile syntheses,morphologies, and optical absorptions of P3HT coil‐rod‐coil triblock copolymers

Here we report syntheses, photophysical properties, and morphologies of a series of coil‐rod‐coil ABA triblock copolymers containing highly regioregular poly(3‐hexylthiophene) (P3HT) as the central rod block. A new methodology, based on the coupling reaction between living polymeric anions [polystyrene, polyisoprene, and poly(methyl methacrylate)] and aldehyde terminated P3HT, was successfully developed to synthesize the triblock copolymers with low polydispersities. This coupling reaction was effective for building blocks with a variety of molecular weights; therefore, a good variation in compositions of the triblock copolymers could be feasibly achieved. The non‐P3HT coil segments and the solvents were found to exhibit noticeable effects on morphologies of the spin‐coated thin films. Attachment of the coil segments to P3HT did not change the optical absorption of the P3HT segment as the block copolymers were dissolved in solution regardless the chemical structure and the molecular weight of the coil segment. Interestingly, different UV–vis absorption behaviors were observed for the spin‐coated thin films of the block copolymers, which closely related to their morphologies. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3311–3322, 2010     

Preparation of methoxy poly(ethylene glycol)/polyester diblock copolymers and examination of the gel‐to‐sol transition

Diblock copolymers consisting of methoxy poly(ethylene glycol) (MPEG) and poly(?‐caprolactone) (PCL), poly(δ‐valerolactone) (PVL), poly(L ‐lactic acid) (PLLA), or poly(lactic‐co‐glycolic acid) (PLGA) as biodegradable polyesters were prepared to examine the phase transition of diblock copolymer solutions. MPEG–PCL and MPEG–PVL diblock copolymers and MPEG–PLLA and MPEG–PLGA diblock copolymers were synthesized by the ring‐opening polymerization of ?‐caprolactone or δ‐valerolactone in the presence of HCl · Et₂O as a monomer activator at room temperature and by the ring‐opening polymerization of L ‐lactide or a mixture of L ‐lactide and glycolide in the presence of stannous octoate at 130 °C, respectively. The synthesized diblock copolymers were characterized with ¹H NMR, IR, and gel permeation chromatography. The phase transitions for diblock copolymer aqueous solutions of various concentrations were explored according to the temperature variation. The diblock copolymer solutions exhibited the phase transition from gel to sol with increasing temperature. As the polyester block length of the diblock copolymers increased, the gel‐to‐sol transition moved to a lower concentration region. The gel‐to‐sol transition showed a dependence on the length of the polyester block segment. According to X‐ray diffraction and differential scanning calorimetry thermal studies, the gel‐to‐sol transition of the diblock copolymer solutions depended on their degrees of crystallinity because water could easily diffuse into amorphous polymers in comparison with polymers with a crystalline structure. The crystallinity markedly depended on both the distinct character and composition of the block segment. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5784–5793, 2004     

Multiblock poly(4‐vinylpyridine) and its copolymer prepared with cyclic trithiocarbonate as a reversible addition–fragmentation transfer agent

The polymerization of 4‐vinylpyridine was conducted in the presence of a cyclic trithiocarbonate (4,7‐diphenyl‐[1,3]dithiepane‐2‐thione) as a reversible addition–fragmentation transfer (RAFT) polymerization agent, and a multiblock polymer with narrow‐polydispersity blocks was prepared. Two kinds of multiblock copolymers of styrene and 4‐vinylpyridine, that is, (ABA)_n multi‐triblock copolymers with polystyrene or poly(4‐vinylpyridine) as the outer blocks, were prepared with multiblock polystyrene or poly(4‐vinylpyridine) as a macro‐RAFT agent, respectively. GPC data for the original polymers and polymers cleaved by amine demonstrated the successful synthesis of amphiphilic multiblock copolymers of styrene and 4‐vinylpyridine via two‐step polymerization. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2617–2623, 2007