Visible-light-driven photocatalysis of heterostructure Ag/Bi<Subscript>2</Subscript>WO<Subscript>6</Subscript> nanocomposites and their photocatalytic degradation of dye under visible light irradiation

Ag/Bi₂WO₆ nanocomposites were successfully synthesized by a combination of hydrothermal method and ultrasonic vibration. The phases, vibration modes, constituents and morphologies were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, field emission scanning electron microscopy, transmission electron microscopy and X-ray photoelectron spectroscopy. The visible-light-driven photocatalytic activitiy of 0–10 wt% Ag/Bi₂WO₆ samples was studied by determining the photodegradation of rhodamine B under xenon lamp. In this research, 10 wt% Ag/Bi₂WO₆ nanocomposites exhibit the highest efficiency and have the promising photocatalytic properties for waste water treatment.     

Photodegradation of dye pollutants on TiO<Subscript>2</Subscript> pillared bentonites under UV light irradiation

TiO₂ pillared bentonite samples dried under different conditions are used to degrade 2,4-dichlorophenol and orange II under UV light irradiation. The supercritical dried sample exhibits a high activity for the photodegradation of 2,4-dichlorophenol and orange II due to its structural features. TOC and COD are measured during the degradation of 2,4-dichlorophenol under UV light irradiation using P25 and TiO₂ pillared bentonite samples dried under different conditions. The clay-based catalysts can be readily separated by filtration or sedimentation.     

Photocatalytic degradation of trichloroethylene on platinum ion-doped TiO<Subscript>2</Subscript> under visible light irradiation

Porous platinum ion-doped TiO₂ (Pt–TiO₂) was prepared by a sol–gel method and demonstrated to have superior photocatalytic activity for the photodegradation of gaseous trichloroethylene (TCE) under visible light (VL) irradiation from a xenon lamp equipped with 422-nm cut-off filter. Kinetic studies were performed to clarify the effect of the doping amounts, space times, VL intensity, and mole fractions of TCE, O₂, and H₂O on the degradation of TCE. Under ultraviolet (UV) irradiation, the photocatalytic activity of Pt–TiO₂ was the same as that of TiO₂, indicating that the doped Pt ion did not act as a recombination center for the photogenerated holes and electrons. Based on the kinetic data and reaction products, we conclude that the photocatalytic degradation of TCE on Pt–TiO₂ under VL irradiation proceeds similarly to TiO₂ under UV irradiation. We also performed the photocatalytic degradation of TCE at the space time of 7.5 × 10⁷ g s mol^?1 in a tubular reactor packed with the Pt–TiO₂ pellets which are more suitable than the Pt–TiO₂ powder for the practical remediation of the contaminated gas. TCE was completely degraded, i.e. 100% conversion was achieved under VL irradiation but only a small quantity of CO₂ was formed with the stoichiometric ratio of [CO₂]_formed/[TCE]_degraded of ca. 0.33. By switching the gas stream containing TCE to humid air, more CO₂ was formed, indicating that the dichloroacetates accumulated on the Pt–TiO₂ surface are photodegradable to CO₂ under VL irradiation.     

Ag<Subscript>3</Subscript>PO<Subscript>4</Subscript>/Bi<Subscript>2</Subscript>MoO<Subscript>6</Subscript> heterostructures with enhanced visible light photocatalytic activity for the degradation of rhodamine B

Highly efficient visible-light-driven Ag₃PO₄/Bi₂MoO₆ hybrid photocatalysts with different mole ratios of Ag₃PO₄ were prepared via sonochemical method and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that product are cubic Ag₃PO₄ nanoparticles supported on orthorhombic Bi₂MoO₆ nanoplates. Under visible light irradiation (>420 nm), the Ag₃PO₄/Bi₂MoO₆ photocatalysts displayed the higher photocatalytic activity than pure Bi₂MoO₆ for the decolorization of rhodamine B (RhB). Among the hybrid photocatalysts, 10% Ag₃PO₄/Bi₂MoO₆ exhibited the highest photocatalytic activity for the decolorization of RhB due to the efficient separation of electron–hole pairs.     

Selective aerobic photocatalytic oxidation of benzyl alcohol over spherical structured WO<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> nanocomposite under visible light irradiation

TiO₂/WO₃ nanocomposite with nanodisk morphology was prepared and successfully used as a photocatalyst. The nanocomposite was obtained via sonochemical and hydrothermal methods, using pomegranate juice as a capping agent. The products were characterized by FE-SEM imaging, BET, EDAX spectroscopy, X-ray diffraction, DRS, and FT-IR spectroscopy. TiO₂/WO₃ nanocomposite showed high sensitivity to absorb visible light in compared to TiO₂. In an optimized condition, the yield of the aerobic photocatalytic oxidation of benzyl alcohol derivatives reached to 65% for the TiO₂/WO₃ nanocomposite, while the conversion percent of the derivatives was less than 8% and 50% on the TiO₂ and WO₃ nanoparticles, respectively. Experimental results were supported by density functional theory (DFT) calculations. The DFT results in several solvents of different dielectric constants, confirmed the strong dependence of light absorption and photocatalytic activity to adsorption energy of the substrates on the surface of the nanoparticles (E_ad). In addition, the theoretical results showed an inverse correlation between the adsorption energy of benzyl alcohol and its conversion percent, accordance to the experimental trend.

Open image in new window

     

Investigation in SrTiO<Subscript>3</Subscript>-CaTiO<Subscript>3</Subscript>-PbTiO<Subscript>3</Subscript> ternary thin films by dielectric proprieties and Raman spectroscopy

Dielectric and Raman scattering experiments were performed on polycrystalline Pb_1−x−yCa_xSr_yTiO₃ thin films as a function of temperature. Temperature-dependent dielectric measurements revealed a decreasing ferroelectric-to-paraelectric phase transition temperature and peak dielectric permittivity showed a broad phase transition near room temperature with increasing levels of CaO₁₂ and SrO₁₂ clusters. Therefore, for higher levels of substitution, the possible random position of the CaO₁₂ and SrO₁₂ clusters leads to a diffuse state. At 100 kHz, the ferroelectric-to-paraelectric phase transition temperatures were 633, 495 and 206 K for PCST90 (Pb_0.90Ca_0.05Sr_0.05TiO₃), PCST70 (Pb_0.70Ca_0.15Sr_0.15TiO₃) and PCST30 (Pb_0.30Ca_0.35Sr_0.35TiO₃) thin films, respectively. The evolution of the Raman spectra was also studied as a function of temperature. The temperature dependence of the E(1TO) soft mode frequencies was used to characterize the phase transition. Raman peaks were observed above the ferroelectric-to-paraelectric phase transition temperature, although all optical modes should be inactive in Raman scattering. The origin of these modes was interpreted as a breakdown of the local cubic symmetry by the random distribution of CaO₁₂ and SrO₁₂ clusters.     

Synthesis,characterization, and photocatalytic properties of La<Superscript>3+</Superscript>-doped BiPO<Subscript>4</Subscript> photocatalysts

La³⁺-doped BiPO₄ photocatalysts were prepared via a hydrothermal process. Their morphologies, structures, and light absorption properties were evaluated. A small amount of La-doping (optimized at 2 mol %) could significantly improve the activity of BiPO₄ in the degradation of methylene blue under ultraviolet irradiation. After five recycles, the La³⁺-doped BiPO₄ did not exhibit any apparent loss in activity, confirming its stability despite recycling.     

Photocatalytic degradation of organic dyes by Er<Superscript>3+</Superscript>: YAlO<Subscript>3</Subscript>/Co- and Fe-doped ZnO coated composites under solar irradiation

In this work, the Er³⁺: YAlO₃/Co- and Fe-doped ZnO coated composites were prepared by the sol-gel method. Then, they were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy dispersive X-ray spectroscopy (EDX). Photo-degradation of azo fuchsine (AF) as a model dye under solar light irradiation was studied to evaluate the photocatalytic activity of the Er³⁺: YAlO₃/Co- and Fe-doped ZnO coated composites. It was found that the photocatalytic activity of Co- and Fe-doped ZnO composites can be obviously enhanced by upconversion luminescence agent (Er³⁺: YAlO₃). Besides, the photocatalytic activity of Er³⁺: YAlO₃/Fe-doped ZnO is better than that of Er³⁺: YAlO₃/Co-doped ZnO. The influence of experiment conditions, such as the concentration of Er³⁺: YAlO₃, heat-treatment temperature and time on the photocatalytic activity of the Er³⁺: YAlO₃/Co- and Fe-doped ZnO coated composites was studied. In addition, the effects of solar light irradiation time, dye initial concentration, Er³⁺: YAlO₃/Co- and Fe-doped ZnO amount on the photocatalytic degradation of azo fuchsine in aqueous solution were investigated in detail. Simultaneously, some other organic dyes, such as Methyl Orange (MO), Rhodamine B (RM-B), Acid Red B (AR-B), Congo Red (CR), and Methyl Blue (MB) were also studied. The possible excitation principle of Er³⁺: YAlO₃/Co- and Fe-doped ZnO coated composites under solar light irradiation and the photocatalytic degradation mechanism of organic dyes were discussed.     

Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>/BiFeO<Subscript>3</Subscript> heterostructure: preparation,characterization, and photocatalytic activity

Bi₂O₃/BiFeO₃ composite was successfully fabricated by a conventional sol–gel method and structural properties were characterized based on X-ray diffractometer, scanning electron microscope, transmission electron microscope, energy-dispersive X-ray analyzer, nitrogen adsorption–desorption measurement, and UV–visible diffuse reflectance spectroscopy. Bi₂O₃/BiFeO₃ had a good absorption for visible light, which was benefit to photocatalytic activity. The highest degradation efficiency was obtained when the content of Bi₂O₃ in Bi₂O₃/BiFeO₃ was 63.9%. Effect of experimental conditions was investigated, and the highest photocatalytic activity of Bi₂O₃/BiFeO₃ was observed at photocatalyst dosage of 0.5 g/L, initial BPA concentration of 10 mg/L, and solution pH of 6.3. Bi₂O₃/BiFeO₃ photocatalyst exhibited enhanced photocatalytic activity for BPA, and the reaction rate constant over Bi₂O₃/BiFeO₃ composite was 2.23, 3.65, and 8.71 times higher than that of BiFeO₃, Bi₂O₃ and commercial TiO₂ (P25), respectively. Bi₂O₃/BiFeO₃ showed high photocatalytic activity after three cycles, suggesting that it was a stable photocatalyst. The possible photocatalytic mechanism has been discussed on the basis of the theoretical calculation and the experimental results. The hydroxyl and superoxide radicals together with photogenerated holes played significant roles in the photocatalytic reaction.     

Photocatalytic property of surface-modified TiO<Subscript>2</Subscript> nanobelts under visible light irradiation

A novel plasmonic photocatalyst, i.e., acid-etched TiO₂ nanobelts attached with Ag/AgI nanoparticles (NPs) was prepared by deposition–precipitation-photoreduction method. Such surface-modified nanobelts had larger area than the normal one. Ag NPs were formed from AgI by photo-reduction under Xenon lamp irradiation. X-ray diffraction, scanning electron microscopy analysis, UV–Vis diffuse reflectance spectra and fluorescence spectra were used to characterize the structure and optical properties of the sample. The obtained sample exhibited strong photodegradation of methyl orange (MO) under visible light irradiation, which were attributed to both the surface plasmon resonance of Ag NPs and the visible light actived AgI. The photodegradation was accomplished by the transfer of photoexcited electrons from the Ag NPs to the acid-etched TiO₂ nanobelts. After four cycles of photodegradation the photocatalyst was still stable. This novel photocatalyst had a high potential application in wastewater-treatment and biomedical engineering.     

Chemical synthesis of Ni/TiO<Subscript>2</Subscript> nanophotocatalyst for UV/visible light assisted degradation of organic dye in aqueous solution

The Ni/TiO₂ nanoparticles with different Ni dopant content were prepared by a modified sol–gel method. The structure and photoinduced charge properties of the as-prepared catalysts were determined using X-ray diffraction, transmission electron microscopy, UV–vis diffuse reflectance spectroscopy and surface photovoltage spectroscopy techniques, and the photocatalytic efficiency of these catalysts was tested using an organic dye. It was shown that Ni modification could greatly enhance the photocatalytic efficiency of these nanocomposite catalysts by taking the photodegradation of methyl orange as a model reaction. With appropriate ratio of Ni and TiO₂, Ni/TiO₂ nanocomposites showed the superior photocatalytic activity than the single TiO₂ nanoparticles. Surface photovoltage spectra demonstrated that Ni modification could effectively inhibit the recombination of the photoinduced electron and holes of TiO₂. This electron–hole pair separation conditions are responsible for the higher photocatalytic performance of Ni/TiO₂ nanocomposites in the visible region of electromagnetic spectrum.     

Phase formation in the InPO<Subscript>4</Subscript>-Na<Subscript>3</Subscript>PO<Subscript>4</Subscript>-Li<Subscript>3</Subscript>PO<Subscript>4</Subscript> ternary system

The 950°C isothermal section of the InPO₄-Na₃PO₄-Li₃PO₄ ternary system was studied and constructed; one-, two, and three-phase fields are outlined. Five solid-solution regions exist in the system: solid solutions based on the complex phosphate LiNa₅(PO₄)₂ (olympite structure), the indium ion stabilized high-temperature Na₃PO₄ phase (Na_{3(1 − x)}In _x (PO₄); space group Fm [`3]\bar 3 m), the complex phosphate Na₃In₂(PO₄)₃, and the α and β phases of the compound Li₃In₂(PO₄)₃. A narrow region of melt was found in the vicinity of eutectic equilibria. All the phases detected in the system are derivatives of phases existing in the binary subsystems. Isovalent substitution of lithium for sodium in Na₃In₂(PO₄)₃ leads to a significant increase in the region of a NASICON-like solid solution.     

Whitlockite solid solutions in the Ca<Subscript>3</Subscript>(VO<Subscript>4</Subscript>)<Subscript>2</Subscript>-K<Subscript>3</Subscript>VO<Subscript>4</Subscript>-NdVO<Subscript>4</Subscript> system

Phase equilibria in the Ca₃(VO₄)₂-K₃VO₄-NdVO₄ system have been studied. An extensive calcium orthovanadate-based solid solution was found to form with the boundary compositions as follows: Ca₃(VO₄)₂-Ca₉Nd(VO₄)₇-Ca_9.33K_2.33(VO₄)₇-Ca_7.88K_2.63Nd_0.87(VO₄)₇. The unit cell parameters of the whit-lockite vanadates synthesized increase as the potassium and neodymium contents increase. Phase transitions from the low-temperature β phase to the β′ centrosymmetrical structure in Ca_{9.33 − 5z} K_{2.33 + z} Nd_3z (VO₄)₇ vanadates have been studied dilatometrically. The increase in the β ai β′ transition temperature caused by potassium is interpreted as arising from the filling in of vacant cation positions M(4) and M(6).     

Phase formation in the Ag<Subscript>2</Subscript>MoO<Subscript>4</Subscript>-MgMoO<Subscript>4</Subscript>-Al<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript> system

The subsolidus region of the Ag₂MoO₄-MgMoO₄-Al₂(MoO₄)₃ ternary salt system has been studied by X-ray phase analysis. The formation of new compounds Ag_{1 ? x} Mg_{1 ? x} Al_{1 + x} (MoO₄)₃ (0 ≤ x ≤ 0.4) and AgMg₃Al(MoO₄)₅ has been determined. The Ag_{1 ? x} Mg_{1 ? x} Al_{1 + x} (MoO₄)₃ variable-composition phase is related to the NASICON type structure (space group R \(\bar 3\) c). AgMg₃Al(MoO₄)₅ is isostructural to sodium magnesium indium molybdate of the same formula unit and crystallizes in triclinic system (space group P \(\bar 1\), Z = 2) with the following unit cell parameters: a = 9.295(7) Å, b = 17.619(2) Å, c = 6.8570(7) Å, α = 87.420(9)°, β = 101.109(9)°, γ = 91.847(9)°. The compounds Ag_{1 ? x} Mg_{1 ? x} Al_{1 + x} (MoO₄)₃ and AgMg₃Al(MoO₄)₅ are thermally stable up to 790 and 820°C, respectively.     

New photocatalysts based on cadmium and zinc sulfides for hydrogen evolution from aqueous Na<Subscript>2</Subscript>S-Na<Subscript>2</Subscript>SO<Subscript>3</Subscript> solutions under irradiation with visible light

Noble metal-free, Cd_{1 − x} Zn _x S-based photocatalysts for hydrogen evolution from aqueous solutions of sodium sulfide and sodium sulfite upon irradiation with visible light (λ > 420 nm) have been synthesized and characterized by a complex of physicochemical methods. The effects of pH and catalyst and substrate concentrations on the rate of photocatalytic hydrogen evolution have been investigated. Under the optimal conditions, the quantum efficiency of the process is up to 12.9%.     

Orientational disorder in crystal structures of (NH<Subscript>4</Subscript>)<Subscript>3</Subscript>ZrF<Subscript>7</Subscript> and (NH<Subscript>4</Subscript>)<Subscript>3</Subscript>NbOF<Subscript>6</Subscript>

Crystal structures of (NH₄)₃ZrF₇ (I) and (NH₄)₃NbOF₆ (II) are refined by X-ray diffraction at room temperature. The compounds are isostructural and belong to the structural type of elpasolite: space group F23; a(I) = 9.4185(3) Å, a(II) = 9.3371(5) Å; V(I) = 835.50(5) ų, V(II) = 814.02(8) ų; Z = 4; R(I) = 0.0145, and R(II) = 0.0138. The refinement of the structures in the space group Fm3m yields abnormally short X-X distances in the pentagonal bipyramid MX₇ (X = F, O). The oxygen atom in II is identified by Nb-X distances and occupies one of the axial vertices of the bipyramid. The Nb atom in II is statistically distributed over the position 24f, while Zr in I resides in the symmetry center. The pentagonal bipyramid MX₇ has six independent orientations in I and twelve in II. One of three crystallographically independent ammonium groups of the structures is disordered over six or twelve equivalent orientations.     

Vanadium-containing polyphosphomolybdate immobilized on TiO<Subscript>2</Subscript> nanoparticles: A recoverable and efficient catalyst for Photochemical,Sonochemical and photosonochemical degradation of dyes under irradiation of UV light

A new photocatalyst, nanoporous anatase TiO₂ crystalline particles coupled by Na₅PV₂Mo₁₀O₄₀ Keggin units, TiO₂-PVMo, was prepared by combination of the methods of sol-gel and hydrothermal treatment. The catalyst was characterized by X-ray diffraction (XRD), UV diffuse reflectance spectroscopy (UV-DRS), FT-IR spectroscopy, Scanning Electron Microscopy (SEM) and cyclovoltametery (CV). This photocatalyst exhibited a good photocatalytic (UV region) and sonocatalytic activity in the decomposition of different dyes in aqueous systems. The TiO₂-PVMo composite showed higher photocatalytic and sonocatalytic activity than pure polyoxometalate or pure TiO₂.     

Glass formation in the Al(IO<Subscript>3</Subscript>)<Subscript>3</Subscript>-Al<Subscript>2</Subscript>(SO<Subscript>4</Subscript>)<Subscript>3</Subscript>-HIO<Subscript>3</Subscript>-H<Subscript>2</Subscript>O system

On the basis of experimental data obtained in the study of glass-formation boundaries in the Al₂(SO₄)₃-HIO₃-H₂O, Al(IO₃)₃-Al₂(SO₄)₃-H₂O, and Al(IO₃)₃-HIO₃-H₂O systems and using geometrical analysis, we predict the positions of glass-formation boundaries in the Al(IO₃)₃-Al₂(SO₄)₃-HIO₃-H₂O four-component system along 60, 40, and 25 wt % H₂O sections.     

Phase equilibria in the system LaMnO<Subscript>3</Subscript>-SrMnO<Subscript>3</Subscript>-SrCrO<Subscript>4</Subscript>-LaCrO<Subscript>3</Subscript>

A continuous solid solution LaMn_1?y Cr _y O₃ with an orthorhombic structure is found to exist in the range of 0.0 ≤ y ≤ 1.0. An orthorhombic solid solution La_1?x Sr _x CrO₃ exists in the range of 0.0 ≤ x ≤ 0.1. The stability boundaries are determined for the perovskite phase La_1?x Sr _x Mn_1?y Cr _y O₃. An isobaric-isothermal section LaMnO₃-SrMnO₃-SrCrO₄-LaCrO₃ of the system La₂O₃-SrO-Mn₃O₄-Cr₂O₃ in air at 1100°C is designed.