氢化物发生–原子吸收光谱法测定铅粉中痕量砷、锑

建立氢化物发生–原子吸收光谱法联用测定铅粉中痕量砷、锑的方法。试样用稀硝酸溶解,用5%抗坏血酸溶液作为砷(Ⅴ)、锑(Ⅴ)的预还原剂,5%的硫脲溶液作为其它元素的掩蔽剂,选用1%硼氢化钠溶液作为还原剂,氢化物反应在10%盐酸介质中进行。在优化的试验条件下,砷、锑的质量浓度在0~20 ng/m L范围内与吸光度线性相关,相关系数r2分别为砷0.999 6,锑0.993 8,方法的检出限分别为砷0.40 ng/m L,锑0.75 ng/m L。砷、锑测定结果的相对标准偏差分别为4.96%,6.27%(n=6),铅粉样品加标回收率分别为砷87.6%,锑79.3%。该方法准确可靠,可用于测定铅粉中痕量砷、锑。     

顺序注射-氢化物发生原子吸收法测定砷

通过在气液分离器的液体出口处增置微型电磁阀,延长样品和还原剂NaBH4在气液分离器中的反应时间,实现了单注射泵顺序注射-氢化物发生原子吸收法测定砷。本法自动化程度高,分析速度112次／h,样品消耗量为0．4mL;4μg/L As测定10次的相对标准偏差为2．0％;检出限0．09μg/L。用于标样中砷的测定,结果满意。     

流动注射-氢化物发生-电热原子吸收光谱法测定水中痕量汞

在酸性溶液中,水样中多种状态存在的汞用高锰酸钾或溴酸钾氧化为二价汞离子,应用流动注射技术和氢化物发生法与电热原子吸收光谱法相结合,在253.7 nm波长下测定了汞含量。方法的线性范围为0.2~15μg.L-1(r=0.999 9)。测得方法的检出限(3σ)为0.094μg.L-1。在水样中加入不同量的汞标准溶液作回收试验,测得回收率在95.7%~104.6%之间。     

氢化物发生-原子吸收光谱法测定萤石粉中砷

提出了以氢化物发生-原子吸收光谱法测定萤石粉中砷的方法,研究了酸介质、还原剂、载气流量等因素对测定的影响,并选择出最佳工作条件.砷的检出限为0.052μg·g-1,线性范围为0.10～6.00 μg·L-1,回收率在90.0%～102.0%之间,相对标准偏差为9.8%.     

氢化物发生-电热原子吸收光谱法测定人发中铅

经清洗并干燥的人发样用硝酸-高氯酸混合酸溶解,试样溶液中铅(Ⅱ)转化成铅烷(PbH4)及试样中铅量的测定采用WHG-102A2型流动注射氢化物发生器及GGX-9型原子吸收光谱仪的联用而自动完成.方法的最佳测定条件,包括铁氰化钾的加入量、原子化温度、高氯酸的影响及干扰试验等作了试验和选择.方法的检出限为0.25μg·L-1,在8μg·g-1的水平上进行精密度试验,测得结果的相对标准偏差(n=10)为3.0%.     

流动注射氢化物发生-原子吸收光谱法测定中药中的微量砷

探讨了流动注射氧化物发生-原子吸收光谱法测定微量砷的最佳条件,建立了中药中微量砷的流动注射氧化物发生-原子吸收光谱分析方法。砷的检出限为0.59μg/L,线性范围为0～30μg/L,线性回归方程为A=0.02228c 6.282×10~(-3),相关系数r=0.9992,相对标准偏差为2.6％～4.4％,回收率为91％～103％。方法操作简便、快速,灵敏度及自动化程度高。     

氢化物发生-原子吸收光谱法测定大米中微量砷

砷是一种毒性很大的元素，对人的心肺、呼吸、神经、生殖、造血、免疫系统都有不同程度的损伤作用]。由于大气、地下水、土壤、肥料和农药等污染，砷会在粮食的可食部分积累，因此砷的测定已成为食品和环境监测的必测项目。测砷的常规方法有砷斑法、银盐法。目前，氢化物原子吸收光谱法，氢化物原子荧光法已有报道。本文采用氢化物发生—原子吸收光谱法测定大米中砷，本法具有灵敏度高，干扰少，操作简便等特点，结果满意。     

氢化物发生-原子吸收光谱法测定蔬菜中痕量铅

采用微波消化、氢化物发生-原子吸收光谱法测定蔬菜中痕量铅。研究了硼氢化钾用量、酸介质及其酸度对铅的测定影响,采用铁氰化钾-草酸体系可消除金属元素对铅测定的干扰。检出限为0．023μg·L-1,回收率为97．8％～105．6％,RSD为0．8％～1．8％,线性范围为0～40μg·L-1。     

氢化物发生-原子吸收光谱法测定食品中的汞

研究了采用氢化物发生-原子吸收光谱法测定食品中痕量汞的方法,通过采用氢化物发生器,选择合适浓度的载流和硼氢化钾,获得了较为满意的分析结果。在测定汞含量5～20μg/kg的食品标准样品时,测试结果相对标准偏差RSD为2.2%～3.7%,回收率为84.9%～97.5%,检出限为0.2μg/L,完全满足食品行业汞元素痕量检测要求,操作简便、快速。     

流动注射-氢化物发生-原子吸收光谱法测定中草药中砷

中草药样品经硝酸-高氯酸-硫酸消化处理后,在酸性条件下用硫脲和抗坏血酸将砷(Ⅴ)还原为砷(Ⅲ),然后再以硼氢化钾为还原剂,稀盐酸为载液,用流动注射氢化物发生原子吸收光谱法测定砷含量.砷的质量浓度在1.6～32.0 μg·L-1范围内与其吸光度呈线性关系,检出限(3s/k)为0.32 μg·L-1.用此方法分析了3种草药样品,砷的测定值的相对标准偏差(n=6)在5.1%～8.1%之间,加标回收率在91.4%～106.1%之间.     

Separation of trace antimony and arsenic prior to hydride generation atomic absorption spectrometric determination

A separation method utilizing a synthetic zeolite (mordenite) was developed in order to eliminate the gas phase interference of Sb(III) on As(III) during quartz furnace hydride generation atomic absorption spectrometric (HGAAS) determination. The efficiency of the proposed separation method in the reduction of suppression effects of transition metal ions on As(III) signal was also investigated. Among the volatile hydride-forming elements and their different oxidation states tested (Sb(III), Sb(V), Se(IV), Se(VI), Te(IV), and Te(VI)), only Sb(III) was found to have a signal depression effect even at low (μg l⁻¹) concentrations under the experimental conditions employed. It has been shown that mordenite adsorbs Sb(III) quantitatively, even at a concentration of 1000 μg l⁻¹, at pHs greater than two, and also, it reduces the initial concentrations of the transition metal ions to lower levels which can be tolerated in many studies. The adsorption of Sb(III) on mordenite follows the Freundlich isotherm and is endothermic in nature.     

氢化物-原子吸收光谱法测定冶金企业废水中的砷

采用HNO3/HClO4(体积比10∶1)消解冶金废水样品,经6mol.L-1 HCl溶液酸化后,加入碘化钾(3%)、抗坏血酸(1%)及硫脲(1%)混合溶液进行还原,用氢化物-原子吸收光谱法(HG-AAS)测定了样品中的As含量.结果表明,该方法的检出限为0.297μg/L,相对标准偏差RSD为5.463%,样品加标回收率为93%～108%;其操作方便、选择性好、灵敏度高、干扰少,适合于复杂废水中微量和痕量As的测定.     

Determination of ultra trace arsenic species in water samples by hydride generation atomic absorption spectrometry after cloud point extraction

Cloud point extraction (CPE) methodology has successfully been employed for the preconcentration of ultra-trace arsenic species in aqueous samples prior to hydride generation atomic absorption spectrometry (HGAAS). As(III) has formed an ion-pairing complex with Pyronine B in presence of sodium dodecyl sulfate (SDS) at pH 10.0 and extracted into the non-ionic surfactant, polyethylene glycol tert-octylphenyl ether (Triton X-114). After phase separation, the surfactant-rich phase was diluted with 2 mL of 1 M HCl and 0.5 mL of 3.0% (w/v) Antifoam A. Under the optimized conditions, a preconcentration factor of 60 and a detection limit of 0.008 μg L⁻¹ with a correlation coefficient of 0.9918 was obtained with a calibration curve in the range of 0.03–4.00 μg L⁻¹. The proposed preconcentration procedure was successfully applied to the determination of As(III) ions in certified standard water samples (TMDA-53.3 and NIST 1643e, a low level fortified standard for trace elements) and some real samples including natural drinking water and tap water samples.     

Determination of total arsenic in seawater by hydride generation atomic fluorescence spectrometry

In this work, the determination of total As in seawater by hydride generation atomic fluorescence spectrometry was studied. The influence of the chemical, flow and instrumental parameters were investigated and optimized. The pre-reduction of As(V) to As(III) was performed using KI plus ascorbic acid in 3.5 mol L^− 1 HCl medium. No multiplicative interference was present and external aqueous calibration could be used. The limit of detection was 36 ng L^− 1, while the repeatability was 2% (n = 10), at a 500 ng L^− 1 concentration level. The sample throughput was 15 h^− 1 if triplicate measurements were made. The accuracy was assessed by the analysis of a seawater certified reference material and excellent agreement between the obtained and certified values was verified. The procedure was used for the analysis of seawater offshore samples collected at the Brazilian coast and results ranging from 860 to 1200 ng L^− 1 were found.     

Investigation of thallium hydride generation using in situ trapping in graphite tube by atomic absorption spectrometry

Thallium hydride was generated from aqueous solutions by merging sample and sodium tetrahydroborate reductant in a batch system. In situ preconcentration of volatile thallium hydride in a preheated graphite furnace coated with palladium, which was used as both the collection medium and atomizer, greatly improved the sensitivity for the determination of thallium by hydride generation atomic absorption spectrometry. The presence of tellurium can increase the generation efficiency of thallium hydride. The operating conditions were optimized. The calibration graph is linear up to 100 ng and the characteristic mass for thallium was 0.92 ng which is seventeen times lower than that obtained with the heated quartz tube atomizer.     

Determination of toxic and non-toxic arsenic species in urine by microwave assisted mineralization and hydride generation atomic absorption spectrometry

Flow injection — microwave oven — hydride generation — atomic absorption spectroscopy (FI-MO-HG-AAS) has been optimized for the determination of the total and toxic arsenic in urine with and without persulfate, respectively. With microwave oven assisted digestion of urine with 5% (w/v) K₂S₂O₈ and 5% (w/v) NaOH all arsenicals completely can be converted to arsenate, which is determined by HG-AAS to give the total concentration of the six species present in urine. The detection limits of 4–6 g l^–1, the relative standard deviation of 3–7% and the high sample throughput make the methods suitable for rapid routine on-line determination. Application of the proposed procedures to the analysis of urine from people on a diet rich in seafood revealed a significant increase in total urinary arsenic due to the rapid excretion of organoarsenicals. Efficient decomposition and quantitative recovery of all arsenic species in spiked urine is achieved by using 5% K₂S₂O₈ in 5% NaOH at 4.6 ml min^–1, microwave power of 700 W and a 1.5 m coil.     

Speciation of inorganic arsenic by electrochemical hydride generation atomic absorption spectrometry

A simple procedure was developed for the speciation of inorganic arsenic by electrochemical hydride generation atomic absorption spectrometry (EcHG–AAS), without pre-reduction of As(V). Glassy carbon was selected as cathode material in the flow cell. An optimum catholyte concentration for simultaneous generation of arsine from As(III) and As(V) was 0.06 mol l⁻¹ H₂SO₄. Under the optimized conditions, adequate sensitivity and difference in ratio of slopes of the calibration curves for As(III) and As(V) can be achieved at the electrolytic currents of 0.6 and 1 A. The speciation of inorganic arsenic can be performed by controlling the electrolytic currents, and the concentration of As(III) and As(V) in the sample can be calculated according to the equations of absorbance additivity obtained at two selected electrolytic currents. The calibration curves were linear up to 50 ng ml⁻¹ for both As(III) and As(V) at 0.6 and 1 A. The detection limits of the method were 0.2 and 0.5 ng ml⁻¹ for As(III) and As(V) at 0.6 A, respectively. The relative standard deviations were of 2.1% for 20 ng ml⁻¹ As(III) and 2.5% for 20 ng ml⁻¹ As(V). The method was validated by the analysis of human hair certified reference material and successfully applied to speciation of soluble inorganic arsenic in Chinese medicine.     

Determination of major antimony species in seawater by continuous flow injection hydride generation atomic absorption spectrometry

The capabilities and limitations of the continuous flow injection hydride generation technique, coupled to atomic absorption spectrometry, for the speciation of major antimony species in seawater, were investigated. Two pre-concentration techniques were examined. After continuous flow injection hydride generation and collection onto a graphite tube coated with iridium, antimony was determined by graphite furnace atomic absorption spectrometry. The low detection limits obtained (∼5 ng l⁻¹ for Sb(III) and ∼10 ng l⁻¹ for Sb(V) for 2.5 ml seawater samples) permitted the determination of Sb(III) and total antimony in seawater with the use of selective hydride generation and on-line UV photooxidation. The number of samples that can be analyzed is about 15 per hour for Sb(III) determinations and 10 per hour for total antimony determinations. The analysis of seawater samples showed that Sb(V) was the predominant species, even in the presence of important biological activity.     

Arsenic in marine tissues — The challenging problems to electrothermal and hydride generation atomic absorption spectrometry

Analytical problems in determination of arsenic in marine tissues are addressed. Procedures for the determination of total As in solubilized or extracted tissues with tetramethylammonium hydroxide and methanol have been elaborated. Several typical lyophilized tissues were used: NIST SRM 1566a ‘Oyster Tissue’, BCR-60 CRM ‘Trace Elements in an Aquatic Plant (Lagarosiphon major)’, BCR-627 ‘Forms of As in Tuna Fish Tissue’, IAEA-140/TM ‘Sea Plant Homogenate’, NRCC DOLT-1 ‘Dogfish Liver’ and two representatives of the Black Sea biota, Mediterranean mussel (Mytilus galloprovincialis) and Brown algae (Cystoseira barbata). Tissues (nominal 0.3 g) were extracted in tetramethylammonium hydroxide (TMAH) 1 ml of 25% m/v TMAH and 2 ml of water) or 5 ml of aqueous 80% v/v methanol (MeOH) in closed vessels in a microwave oven at 50 °C for 30 min. Arsenic in solubilized or extracted tissues was determined by electrothermal atomic absorption spectrometry (ETAAS) after appropriate dilution (nominally to 25 ml, with further dilution as required) under optimal instrumental parameters (pyrolysis temperature 900 °C and atomization temperature 2100 °C) with 1.5 μg Pd as modifier on Zr–Ir treated platform. Platforms have been pre-treated with 2.7 μmol of zirconium and then with 0.10 μmol of iridium which served as a permanent chemical modifier in direct ETAAS measurements and as an efficient hydride sequestration medium in flow injection hydride generation (FI-HG)–ETAAS. TMAH and methanol extract 96–108% and 51–100% of As from CRMs. Various calibration approaches have been considered and critically evaluated. The effect of species-dependent slope of calibration graph or standard additions plot for total As determination in a sample comprising of several individual As species with different ETAAS behavior has been considered as a kind of ‘intrinsic element speciation interference’ that cannot be completely overcome by standard additions technique. Calibration by means of CRMs has given only semi-quantitative results. The limits of detection (3σ) were in the range 0.5–1.2 mg kg^− 1 As dry weight (wt.) for direct ETAAS analysis of extracts in both TMAH and MeOH. Within-run precision (RSD%) was 5–15% and 7–20% for TMAH and MeOH extracts at As levels 4–50 mg kg^− 1 dry wt., respectively.     

石墨炉原子吸收法测定石脑油中微量砷

试样用四氢呋喃（THF）有机溶剂稀释,以硝酸镍为基体改进剂,研究采用石墨炉原子吸收法直接进样测定石脑油中的砷量。研究表明,砷量在0～50μg／L范围内线性关系良好,回收率93％～104％。