超声清洗装置空化噪声谱分析法空化噪声级测量

空化强度是用以衡量液体介质中空化活动的剧烈程度,同时空化效应在超声清洗中起关键作用,因此,测量超声清洗槽中的空化强度便可了解其中空化活动的情况.当发生空化时,液体介质中会产生成分复杂空化噪声,对空化噪声谱进行分析和计算得到空化噪声级,据此可判断空化强度.实验测得结果表明:超声清洗装置内稳态空化分布广泛、均匀,瞬态空化分...     

超声空化与超声医学

随着超声技术应用广泛而迅速的发展,整整一个世纪来,超声空化成了经久不衰的研究课题,特别近１０年来,超声空化成了多种学科的基础研究热点。本扼要地介绍了起声空化的最新研究进展,以及超声空化与超声医学发展的密切关系。     

High-efficiency degradation catalytic performance of a novel Angelica sinensis polysaccharide-silver nanomaterial for dyes by ultrasonic cavitation

Currently, the polluted wastewater discharged by industry accounts for the major part of polluted bodies of water. As one of the industrial wastewaters, dye wastewater is characterized by high toxicity, wide pollution, and difficulty in decolorization degradation. In this paper, a novel composite nanomaterial catalyst of silver was prepared by using Angelica sinensis polysaccharide (ASP) as a reducing and stabilizing agent. And the optimum reaction conditions explored are V_AgNO3 = 5 mL (300 mM) and v_ASP = 7% (w/v) for 6 h at 90 °C. In addition, the ASP-Ag nanocatalyst was characterized by several techniques. The results demonstrated that ASP-Ag nanoparticles were successfully synthesized. Degradation rate, which provides a numerical visualization of the percentage reduction in pollutant concentration. With the wrapping of ASP, the ultrasonic catalytic degradation rates of different organic dyes including rhodamine B (RB), methylene blue (MB), and methyl orange (MO) were from 88.2%, 88.7%, and 85.2% to 96.1%, 95.2% and 93.5% at room temperature, respectively. After the experiments, when c_dyes = 10 mg/L, the highest degradation rate can be observed under c_APS-AgNPs = 10 mg/L with the most powerful cavitation frequency f = 59 kHz. The effect of ultrasonic frequency on the acoustic pressure distribution in the reactor was investigated by using COMSOL Multiphysis^@ software to propose the mechanism of ultrasonic degradation and the mechanism was confirmed by OH radical trapping experiments. It indicates that OH produced by the ultrasonic cavitation effect plays a determinant role in the degradation. And then, the intermediate products of the dye degradation process were analyzed by gas chromatography and mass spectrometry (GC–MS), and the possible degradation processes of dyes were proposed. The resulting products of degradation are SO₄²⁻, NH₄⁺, NO₃⁻, N₂, CO₂ and H₂O. Finally, the recycling degradation experiments showed that catalyst maintains a high degradation rate within reusing 5 cycles. Thus, this catalyst is highly efficient and recyclable.     

Numerical modelling of ultrasonic waves in a bubbly Newtonian liquid using a high-order acoustic cavitation model

To address difficulties in treating large volumes of liquid metal with ultrasound, a fundamental study of acoustic cavitation in liquid aluminium, expressed in an experimentally validated numerical model, is presented in this paper. To improve the understanding of the cavitation process, a non-linear acoustic model is validated against reference water pressure measurements from acoustic waves produced by an immersed horn. A high-order method is used to discretize the wave equation in both space and time. These discretized equations are coupled to the Rayleigh-Plesset equation using two different time scales to couple the bubble and flow scales, resulting in a stable, fast, and reasonably accurate method for the prediction of acoustic pressures in cavitating liquids. This method is then applied to the context of treatment of liquid aluminium, where it predicts that the most intense cavitation activity is localised below the vibrating horn and estimates the acoustic decay below the sonotrode with reasonable qualitative agreement with experimental data.     

超声空化状态对苯酚降解的影响

给出不同空化状态下超声波降解苯酚溶液的实验结果,比较了相应的声压级频谱和合成声强。研究了苯酚溶液的浓度,二阶铁盐,超声辐射时间对苯酚降解率的影响,讨论了不同空化状态下的声压级频谱特征。     

Numerical 3D flow simulation of ultrasonic horns with attached cavitation structures and assessment of flow aggressiveness and cavitation erosion sensitive wall zones

As a contribution to a better understanding of cavitation erosion mechanisms, a compressible inviscid finite volume flow solver with barotropic homogeneous liquid–vapor mixture cavitation model is applied to ultrasonic horn set-ups with and without stationary specimen, that exhibit attached cavitation at the horn tip. Void collapses and shock waves, which are closely related to cavitation erosion, are resolved. The computational results are compared to hydrophone, shadowgraphy and erosion test data. At the horn tip, vapor volume and topology, subharmonic oscillation frequency as well as the amplitude of propagating pressure waves are in good agreement with experimental data. For the evaluation of flow aggressiveness and the assessment of erosion sensitive wall zones, statistical analyses of wall loads and of the multiplicity of distinct collapses in wall-adjacent flow regions are applied to the horn tip and the stationary specimen. An a posteriori projection of load collectives, i.e. cumulative collapse rate vs. collapse pressure, onto a reference grid eliminates the grid dependency effectively for attached cavitation at the horn tip, whereas a significant grid dependency remains at the stationary specimen. The load collectives show an exponential decrease towards higher collapse pressures. Erosion sensitive wall zones are well predicted for both, horn tip and stationary specimen, and load profiles are in good qualitative agreement with measured topography profiles of eroded duplex stainless steel samples after long-term runs. For the considered amplitude and gap width according to ASTM G32-10 standard, the analysis of load collectives reveals that the distinctive erosive ring shape at the horn tip can be attributed to frequent breakdown and re-development of a small portion of the tip-attached cavity. This partial breakdown of the attached cavity repeats at each driving cycle and is associated with relatively moderate collapse peak pressures, whereas the stationary specimen is rather unfrequently stressed at the end of each subharmonic oscillation cycle by the violent collapse of the complete cavity.     

Study on a novel omnidirectional ultrasonic cavitation removal system for Microcystis aeruginosa

Microcystis aeruginosa, as a typical alga, produces microcystin with strong liver toxicity, seriously endangering the liver health of human and animals. Inhibiting the bloom of the Microcystis aeruginosa in lakes becomes a significant and meaningful work. Ultrasonic cavitation is currently considered to be the most environmentally friendly and effective method for the removal of Microcystis aeruginosa. However, the commercialized ultrasonic algae removal systems require multi-Langevin transducers to achieve omnidirectional ultrasonic irradiation due to the single irradiation direction of the Langevin transducer, resulting in the complex design and high energy consumption. To achieve a low-cost, simple structure, and high-efficiency algae removal system, a novel omnidirectional ultrasonic cavitation removal system for Microcystis aeruginosa is proposed. The proposed system is major composed of a novel omnidirectional ultrasonic transducer, which generates the omnidirectional ultrasonic irradiation by its shaking-head motion coupled by two orthogonal bending vibration modes. Modal simulation, sound field simulation, and cavitation bubble radius simulation are first carried out to optimize the geometric sizes of the proposed transducer and verify the correctness of the omnidirectional ultrasonic irradiation principle. Then the vibration characteristics of the transducer prototype are measured by vibration tests and impedance tests. Finally, the feasibility and effectiveness of the proposed omnidirectional ultrasonic removal system for Microcystis aeruginosa are evaluated through the algae removal experiments. The experimental results exhibit that the algal cells damaged by ultrasonic irradiation from the proposed system do not have the ability to self-repair. In addition, the algal removal rates reached 55.41% and 72.97% after 30 min of ultrasonic treatment when the corresponding ultrasonic densities are 0.014 W/mL and 0.021 W/mL, respectively. The proposed omnidirectional ultrasonic algae removal system significantly simplifies the configuration and reduces energy consumption, presenting the potential promise of algae removal and environmental protection.     

Acoustic resonance for contactless ultrasonic cavitation in alloy melts

Contactless ultrasound is a novel, easily implemented, technique for the Ultrasonic Treatment (UST) of liquid metals. Instead of using a vibrating sonotrode probe inside the melt, which leads to contamination, we consider a high AC frequency electromagnetic coil placed close to the metal free surface. The coil induces a rapidly changing Lorentz force, which in turn excites sound waves. To reach the necessary pressure amplitude for cavitation with the minimum electrical energy use, it was found necessary to achieve acoustic resonance in the liquid volume, by finely tuning the coil AC supply frequency. The appearance of cavitation was then detected experimentally with an externally placed ultrasonic microphone and confirmed by the reduction in grain size of the solidified metal. To predict the appearance of various resonant modes numerically, the exact dimensions of the melt volume, the holding crucible, surrounding structures and their sound properties are required. As cavitation progresses the speed of sound in the melt changes, which in practice means resonance becomes intermittent. Given the complexity of the situation, two competing numerical models are used to compute the soundfield. A high order time-domain method focusing on a particular forcing frequency and a Helmholtz frequency domain method scanning the full frequency range of the power supply. A good agreement is achieved between the two methods and experiments which means the optimal setup for the process can be predicted with some accuracy.     

超声空化对丙酮激光喇曼光谱的影响

本研究设计了一种可吸入超声的喇曼光谱样品池,对丙酮的激光喇光曼谱的检测表明,超声空化降低了喇曼光谱的强度,我们认为,超声空化减少了激光光路上参与散射的丙酮分子数是光谱强度降低的主要原因。     

The influence of air content in water on ultrasonic cavitation field

Cavitation is a complex physical phenomenon affected by many factors, one of which is the gas dissolved in the medium. Researchers have given some efforts to the influence of gas content on sonoluminescence or some specific chemical reactions in and around the bubble, but limited work has been reported about the influence on the ultrasonic cavitation field distribution. In this work, the intensity distribution of the ultrasound field in a cleaning tank has been measured with the hydrophone. After analysed and visualised by MATLAB software, it was found that the cavitation intensity distribution in degassed water was much better than that in tap water. And further study proved that degassing process can improve the cavitation effect dramatically both in intensity and scope. Finally, the cavitation fields in mediums with different gas content were measured and the specific influence of air content on cavitation field was discussed.     

超声空化及其声流结构实验研究*

超声空化及其声流效应在医学、化工和能源等领域得到广泛应用。本文采用高速摄像和粒子图像测速系统分别研究了超声场下的空化形态和声流场结构的时空演化规律。实验研究了50W,100W,200W和250W等四种不同输入功率对18kHz的超声变幅杆附近空化及其声流场的影响。研究结果表明：（1）在变幅杆下端面处观察到由大量空化气泡均匀分布组成的倒置锥形空泡结构,并且锥形空泡结构为稳态流动结构。（2）在超声变幅杆附近产生了两种不同的声流形式,第一种是变幅杆底端的射流型声流,第二种是变幅杆两侧的回旋流。此外,通过研究空泡与声流场中最大速度点之间的空间对应关系,发现声流是因为空泡流动带动而产生的。（3）空间位置和输入功率能显著影响射流型声流的流场结构,但是对回旋流的影响十分微弱。     

Damage characteristics and surface description of near-wall materials subjected to ultrasonic cavitation

For the analysis of ultrasonic cavitation erosion on the surface of materials, the ultrasonic cavitation erosion experiments for AlCu4Mg1 and Ti6Al4V were carried out, and the changes of surface topography, surface roughness, and Vickers hardness were explored. Cavitation pits gradually expand and deepen with the increase of experiment time, and Ti6Al4V is more difficult to erode by cavitation than AlCu4Mg1. After experiments, the cavitation damage characteristics such as the single pit, the rainbow ring area, the fisheye pit, and some small pits were observed, which can be considered to be induced by a single micro-jet impact, ablation effect caused by the high temperature, micro-jet impingement with a sharp angle, and multibeam micro-jets coupling impact or negative pressure in the local area produced by micro-jet impact, respectively. The surface roughness and Vickers hardness of the material increase slowly after rapid growth at different points in time as the experiment time increases. With the increase of the ultrasonic amplitude, both of them first increase and then decrease after the ultrasonic amplitude is greater than 10.8 μm. The increases in surface roughness and Vickers hardness tend to decrease as the viscosity coefficient increases. Ultrasonic cavitation can cause submicron surface roughness and increase surface hardness by 20.36%, so it can be used as a surface treatment method.     

Physical and chemical effects of acoustic cavitation in selected ultrasonic cleaning applications

Acoustic cavitation in a liquid medium generates several physical and chemical effects. The oscillation and collapse of cavitation bubbles, driven at low ultrasonic frequencies (e.g., 20 kHz), can generate strong shear forces, microjets, microstreaming and shockwaves. Such strong physical forces have been used in cleaning and flux improvement of ultrafiltration processes. These physical effects have also been shown to deactivate pathogens. The efficiency of deactivation of pathogens is not only dependent on ultrasonic experimental parameters, but also on the properties of the pathogens themselves. Bacteria with thick shell wall are found to be resistant to ultrasonic deactivation process. Some evidence does suggest that the chemical effects (radicals) of acoustic cavitation are also effective in deactivating pathogens. Another aspect of cleaning, namely, purification of water contaminated with organic and inorganic pollutants, has also been discussed in detail. Strong oxidising agents produced within acoustic cavitation bubbles could be used to degrade organic pollutants and convert toxic inorganic pollutants to less harmful substances. The effect of ultrasonic frequency and surface activity of solutes on the sonochemical degradation efficiency has also been discussed in this overview.     

Directional transport and random motion of particles in ALF ultrasonic cavitation structure

The motion of particles of different properties and sizes in ALF ultrasonic cavitation structure is investigated experimentally with high-speed photography. Particles tend to transport along the bubble chain and move towards the focus repeatedly and predictably in ALF cavitation structures. Particles at the focus aggregate and separate alternately over time. The separation of particles mainly occurs in the expansion process of cavitation bubbles, while the movement and aggregation of particles mostly take place during the collapse stage. The directional transport of particles along the bubble chain of ALF cavitation cloud and the random aggregation and dispersion at the focus of ALF are all related to the cavitation bubbles attached to the particles. The directional transportation (predictable, repeatable and pipeline-free) and aggregation of particles in ALF cavitation clouds may be used in special occasions, for example, drug delivery and targeted therapy.     

Chemical activation of ultrasonic cavitation

A method for intensifying ultrasonic cavitation in water and aqueous solutions has been proposed, which consists of a chemical fixation of dissolved oxygen. The influence of selected reducing agents on the intensity of cavitation in water and alkaline solutions has been investigated.     

Investigation on ultrasonic cavitation erosion of TiMo and TiNb alloys in sulfuric acid solution

Two kinds of Ti-alloys, i.e., TiMo and TiNb alloys are manufactured in this paper, and their ultrasonic cavitation erosion behaviors in 0.1 M H₂SO₄ solution are evaluated by the mean depth erosion (MDE), SEM and white light photograph. The results show that MDE of TiMo and TiNb alloys obviously increase with increasing the cavitation erosion time, however, they evidently decrease with the increment of Mo or Nb content at each fixed cavitation erosion time, and even some large blank areas (uneroded areas) still exist on the sample surface after ultrasonic cavitation erosion for 2 h in the case of Ti10Mo and Ti20Nb samples, implying the enhanced anti-cavitation erosion property of Ti-alloy by adding Mo or Nb element. The MDE of Ti10Mo or Ti20Nb sample is lower than that of TC4 sample in the case of each cavitation erosion time, indicating the better cavitation erosion resistance of of Ti10Mo or Ti20Nb sample. The influences of Mo and Nb on the passivity of TiMo and TiNb alloys during the ultrasonic cavitation erosion are detected by potentiodynamic curves. The results display that Ti, TC4, TixMo (x = 1, 5, 10) and TixNb (x = 5, 10, 20) samples are all almost in the passive state within the potential region from 0V_SCE to 1.5V_SCE during ultrasonic cavitation erosion, and the passive current density evidently decreases with increasing Mo or Nb content, indicating the enhanced passive characteristic by adding Mo or Nb alloys during the ultrasonic cavitation erosion.     

Generation and control of acoustic cavitation structure

The generation and control of acoustic cavitation structure are a prerequisite for application of cavitation in the field of ultrasonic sonochemistry and ultrasonic cleaning. The generation and control of several typical acoustic cavitation structures (conical bubble structure, smoker, acoustic Lichtenberg figure, tailing bubble structure, jet-induced bubble structures) in a 20–50 kHz ultrasonic field are investigated. Cavitation bubbles tend to move along the direction of pressure drop in the region in front of radiating surface, which are the premise and the foundation of some strong acoustic cavitation structure formation. The nuclei source of above-mentioned acoustic cavitation structures is analyzed. The relationship and mutual transformation of these acoustic cavitation structures are discussed.     

Study of ultrasonic cavitation during extraction of the peanut oil at varying frequencies

The ultrasonic extraction of oils is a typical physical processing technology. The extraction process was monitored from the standpoint of the oil quality and efficiency of oil extraction. In this study, the ultrasonic cavitation fields were measured by polyvinylidene fluoride (PVDF) sensor. Waveform of ultrasonic cavitation fields was gained and analyzed. The extraction yield and oxidation properties were compared. The relationship between the fields and cavitation oxidation was established. Numerical calculation of oscillation cycle was done for the cavitation bubbles. Results showed that the resonance frequency, f_r, of the oil extraction was 40 kHz. At f_r, the voltage amplitude was the highest; the time was the shortest as reaching the amplitude of the waveform. Accordingly, the cavitation effect worked most rapidly, resulting in the strongest cavitation intensity. The extraction yield and oxidation properties were closely related to the cavitation effect. It controlled the cavitation oxidation effectively from the viewpoint of chemical and physical aspects.     

The role of passive potential in ultrasonic cavitation erosion of titanium in 1 M HCl solution

The influence of the applied passive potential on the ultrasonic cavitation erosion of Ti specimen in 1 M HCl solution was investigated by mass loss experiment, scanning electron microscopy (SEM), electrochemical impedance spectra (EIS) and Mott–Schottky plot. The results showed that Ti was in the passive state within the potential region from −0.3 V_SCE to 1.5 V_SCE under ultrasonic cavitation erosion. The applied passive potential can obviously decrease the mass loss of Ti caused by ultrasonic cavitation erosion in 1 M HCl solution. The resistance of the passive film increased, the flat band potential moved to positive direction, and the donor density of the passive film decreased with increasing the passive potential. Finally, a physical model was provided to explain the experimental results based on energy band and semi-conductive theories.