Sonoactivated polycrystalline Ni electrodes for alkaline oxygen evolution reaction

The development of cost-effective and active water-splitting electrocatalysts is an essential step toward the realization of sustainable energy. Its success requires an intensive improvement in the kinetics of the anodic half-reaction of the oxygen evolution reaction (OER), which determines the overall system efficiency to a large extent. In this work, we designed a facile and one-route strategy to activate the surface of metallic nickel (Ni) for the OER in alkaline media by ultrasound (24 kHz, 44 W, 60% acoustic amplitude, ultrasonic horn). Sonoactivated Ni showed enhanced OER activity with a much lower potential at + 10 mA cm⁻² of + 1.594 V vs. RHE after 30 min ultrasonic treatment compared to + 1.617 V vs. RHE before ultrasonication. In addition, lower charge transfer resistance of 11.1 Ω was observed for sonoactivated Ni as compared to 98.5 Ω for non-sonoactivated Ni. In our conditions, ultrasound did not greatly affect the electrochemical surface area (A_ecsa) and Tafel slopes however, the enhancement of OER activity can be due to the formation of free OH^• radicals resulting from cavitation bubbles collapsing at the electrode/electrolyte interface.     

Zinc-chromium layered double hydroxides anchored on carbon nanotube and biochar for ultrasound-assisted photocatalysis of rifampicin

In this study, ZnCr layered double hydroxide (LDH), ZnCr LDH/carbon nanotube (CNT), and ZnCr LDH/Biochar (BC) were synthesized and characterized by various analyses. The successful synthesis and the great crystallinity of the samples were consented by XRD analysis. SEM and TEM were applied to study the morphology of the synthesized samples. The simultaneous presence of C, Zn, and Cr elements was well confirmed by EDX and dot mapping analyses demonstrating the successful preparation of nanocomposites. According to the BET analysis, ZnCr LDH nanocomposites with BC and CNT had more specific surface area compared to ZnCr LDH alone. The catalytic performances of the samples were determined for the degradation of rifampicin (RF). The degradation efficiency of the sonophotocatalytic process in the presence of 0.6 g L⁻¹ of ZnCr LDH/BC toward 15 mg L⁻¹ of RF under 150 W ultrasound and visible light irradiation was found to be about 100% within 40 min. The influence of the reactive species on the sonophotocatalytic process was assessed via the addition of different scavengers (para-benzoquinone (p-BQ), formic acid (FA), isopropyl alcohol (IPA)), and enhancers (hydrogen peroxide and potassium persulfate). The GC–MS analysis was carried out and eleven by-products during the RF decomposition were detected.     

Ultrasound-assisted conversion of tannic acid to gallic acid as a strategy to obtain value-added products

In this work, ultrasound was applied for the conversion of tannic acid into gallic acid using only diluted H₂O₂ as reagent. Experiments were carried out using several types of ultrasonic horns operating at 20 kHz (VC750W processor). The following experimental conditions were evaluated: H₂O₂ concentration (0.2 to 8.5 mol L⁻¹), horn type (10 to 25 mm of diameter), ultrasound amplitude (20 to 70%), sonication time (10 to 45 min), tannic acid concentration (170 to 1360 mg L⁻¹), and reaction temperature (50 to 90 °C). Gallic acid production was monitored with ultra-performance liquid chromatography with high-resolution time-of-flight mass spectrometry (UPLC-ToF-MS). The isolated gallic acid was confirmed with nuclear magnetic resonance (¹H and ¹³C NMR). It is important to emphasize that this study was developed as a proof of concept to demonstrate the potential of ultrasound for tannic acid conversion into gallic acid using just diluted H₂O₂. Under selected conditions gallic acid production yield was 128 ± 4 mg g⁻¹ of initial tannic acid (using 170 mg L⁻¹ of tannic acid as starting material). Reaction time was set as 30 min, which was carried out using 1 mol L⁻¹ H₂O₂ and ultrasound amplitude of 50% at 90 °C. At silent conditions (mechanical stirring, from 100 to 1000 rpm), gallic acid production was halved (less than 78 ± 4 mg g⁻¹ of initial tannic acid).     

Ultrasound-homogenization-assisted extraction of polyphenols from coconut mesocarp: Optimization study

Coconut pericarp (shell fiber (mesocarp) and shell (endocarp)), the main by-product of coconut production, is often discarded and causing serious environmental pollution. To make better use of coconut pericarp, the extraction process of polyphenols from coconut mesocarp (CM) carefully studied by screening seven solvent systems, optimizing the assisted ultrasonic process by response surface methodology, and comparing the four processes of Ultrasound-Assisted Extraction (UAE), Homogenization-Assisted Extraction (HAE), Homogenization-Ultrasound-Assisted Extraction (HUAE), and Ultrasound-Homogenization-Assisted Extraction (UHAE). The UAE and HAE are considered to be the main methods for efficient extraction of natural active ingredients. The former effectively destroys the cell wall structure and promotes the intermolecular diffusion based on the cavitation, thermal and mechanical effect of ultrasonic, while the latter breaks the material based on strong shear force between the rotor and stator. Their combinations (HUAE and UHAE) enhance the damage to the cell wall of raw materials and improve the extraction efficiency by the synergistic effect. The results showed that using 60% acetone (V : V) as extraction solvent, solid-liquid ratio of 1:5 g mL⁻¹, ultrasonic temperature of 80 ℃, ultrasonic time of 80 min, ultrasonic power of 225 W, and then homogenizing at 10,000 rpm for 10 min, the total flavonoid content of CM reached the maximum value of 551.99 ± 12.69 mg Rutin g⁻¹ dry weight (dw), while the total phenolic content reached the maximum value of 289.48 ± 4.41 mg GAE g⁻¹ dw at 10,000 rpm for 5 min, which may be related to the oxidative degradation of polyphenols caused by the increase of polyphenol oxidase with the extension of homogenization time. This study provides a technical guarantee for the further utilization of phenolic substances in CM.     

Peroxydisulfate-assisted sonocatalytic degradation of metribuzin by La-doped ZnFe layered double hydroxide

Metribuzin is an herbicide that easily contaminates ground and surface water. Herein, La-doped ZnFe layered double hydroxide (LDH) was synthesized for the first time and used for the degradation of metribuzin via ultrasonic (US) assisted peroxydisulfate (PDS) activation. The synthesized LDH had a lamellar structure, an average thickness of 26 nm, and showed mesoporous characteristics, including specific surface area 110.93 m² g⁻¹, pore volume 0.27 cm³ g⁻¹, and pore diameter 9.67 nm. The degradation efficiency of the US/La-doped ZnFe LDH/PDS process (79.1 %) was much greater than those of the sole processes, and the synergy factor was calculated as 3.73. The impact of the reactive species on the sonocatalytic process was evaluated using different scavengers. After four consecutive cycles, 10.8 % loss occurred in the sonocatalytic activity of the La-doped LDH. Moreover, the efficiency of the US/La-doped LDH/PDS process was studied with respect to the degradation of metribuzin in a wastewater matrix. According to GC–MS analysis, six by-products were detected during the degradation of metribuzin. Our results indicate that the US/La-doped ZnFe LDH/PDS process has great potential for efficient degradation of metribuzin-contaminated water and wastewater.     

Optimization of ultrasound-assisted dispersive solid-phase microextraction based on nanoparticles followed by spectrophotometry for the simultaneous determination of dyes using experimental design

A simple, low cost and ultrasensitive method for the simultaneous preconcentration and determination of trace amount of auramine-O and malachite green in aqueous media following accumulation on novel and lower toxicity nanomaterials by ultrasound-assisted dispersive solid phase micro-extraction (UA-DSPME) procedure combined with spectrophotometric has been described. The Mn doped ZnS nanoparticles loaded on activated carbon were characterized by Field emission scanning electron microscopy (FE-SEM), particle size distribution, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) analyses and subsequently were used as green and efficient material for dyes accumulation. Contribution of experimental variables such as ultrasonic time, ultrasonic temperature, adsorbent mass, vortex time, ionic strength, pH and elution volume were optimized through experimental design, and while the preconcentrated analytes were efficiently eluted by acetone. Preliminary Plackett–Burman design was applied for selection of most significant factors and giving useful information about their main and interaction part of significant variables like ultrasonic time, adsorbent mass, elution volume and pH were obtained by central composite design combined with response surface analysis and optimum experimental conditions was set at pH of 8.0, 1.2 mg of adsorbent, 150 μL eluent and 3.7 min sonication. Under optimized conditions, the average recoveries (five replicates) for two dyes (spiked at 500.0 ng mL⁻¹) changes in the range of 92.80–97.70% with acceptable RSD% less than 4.0% over a linear range of 3.0–5000.0 ng mL⁻¹ for the AO and MG in water samples with regression coefficients (R²) of 0.9975 and 0.9977, respectively. Acceptable limits of detection of 0.91 and 0.61 ng mL⁻¹ for AO and MG, respectively and high accuracy and repeatability are unique advantages of present method to improve the figures of merit for their accurate determination at trace level in complicated materials.     

NiFe LDH-CoPc/CNTs as novel bifunctional electrocatalyst complex for zinc–air battery

A new type of composite electrocatalyst was designed and prepared with NiFe layered double hydroxides (LDHs) for oxygen evolution reaction (OER) and CoPc for oxygen reduction reaction (ORR) supported on carbon nanotubes (CNTs). The NiFe LDH–CoPc/CNT composite exhibits higher electrocatalytic activity and stability than the commercial precious metal catalyst Pd/C + Ru/C in 6 M KOH electrolyte. The resulting rechargeable Zn–air battery showed high discharge voltage at 195 mW cm^?2. The discharge voltage is around 1.08~0.95 V and the charge voltage is lower, 2.07 V, after the cycle of 300 h at 80 mA cm^?2, indicating that zinc–air battery possessed high reversibility and durability over long charge and discharge cycles.     

Ultrasound-assisted formation of chitosan-glucose Maillard reaction products to fabricate nanoparticles with enhanced antioxidant activity

The influence of ultrasonic processing parameters including reaction temperature (60, 70 and 80 °C), time (0, 15, 30, 45 and 60 min) and amplitude (70, 85 and 100%) on the formation and antioxidant activity of Maillard reaction products (MRPs) in a solution of chitosan and glucose (1.5 wt% at mass ratio of 1:1) was investigated. Selected chitosan-glucose MRPs were further studied to determine the effects of solution pH on the fabrication of antioxidative nanoparticles by ionic crosslinking with sodium tripolyphosphate. Results from FT-IR analysis, zeta-potential determination and color measurement indicated that chitosan-glucose MRPs with improved antioxidant activity were successfully produced using an ultrasound-assisted process. The highest antioxidant activity of MRPs was observed at the reaction temperature, time and amplitude of 80 °C, 60 min and 70%, respectively, with ∼ 34.5 and ∼20.2 μg Trolox mL⁻¹ for DPPH scavenging activity and reducing power, respectively. The pH of both MRPs and tripolyphosphate solutions significantly influenced the fabrication and characteristics of the nanoparticles. Using chitosan-glucose MRPs and tripolyphosphate solution at pH 4.0 generated nanoparticles with enhanced antioxidant activity (∼1.6 and ∼ 1.2 μg Trolox mg⁻¹ for reducing power and DPPH scavenging activity, respectively) with the highest percentage yield (∼59%), intermediate particle size (∼447 nm) and zeta-potential ∼ 19.6 mV. These results present innovative findings for the fabrication of chitosan-based nanoparticles with enhanced antioxidant activity by pre-conjugation with glucose via the Maillard reaction aided by ultrasonic processing.     

Ultrasonic-assisted recycling of Nile tilapia fish scale biowaste into low-cost nano-hydroxyapatite: Ultrasonic-assisted adsorption for Hg2+ removal from aqueous solution followed by “turn-off” fluorescent sensor based on Hg2+-graphene quantum dots

This study was planned to recycle calcium and the phosphorus-rich Nile tilapia fish scale biowaste into nano-hydroxyapatite (FHAP), using ultrasonic-assisted extraction of calcium and phosphorus from fish scales, which was optimized in term of extraction time, acid concentration, extraction temperature, and ultrasonic power. These two elements were determined simultaneously by inductively coupled plasma atomic emission spectrometry and the FHAP phase was formed upon addition of the extracted element solution in alkaline medium using homogenous precipitation assisted with ultrasound energy. The FHAP adsorbent was characterized by x-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, and Brunauer-Emmett-Teller. A combination of FHAP and the ultrasonic method was then used to remove Hg²⁺ from aqueous solution. Four significant variables affecting Hg²⁺ removal, namely, adsorbent dosage, pH, ultrasonic power, and adsorption time, were studied. The results exhibited that the optimal conditions for maximizing the removal of Hg²⁺ were 0.02 g adsorbent dosage, pH 8, 0.4 kW ultrasonic power, 20 min adsorption time, and 30 °C adsorption temperature. The sorption mechanism of Hg²⁺ was revealed by isotherm modeling, indicating that FHAP adsorbent has a potential for Hg²⁺ removal in aqueous media with the maximum adsorption capacity being 227.27 mg g⁻¹. This adsorption behavior is in agreement with the Langmuir model as reflected by a satisfactory R² value of 0.9967, when the kinetics data were fitted with pseudo-second-order. Therefore, the FHAP could be an alternative adsorbent for the ultrasonic-assisted removal of Hg²⁺ at very high efficiency and within a very short period of time.     

Ultrasonic potential in maintaining the quality and reducing the microbial load of minimally processed pomegranate

Difficulty of Pomegranate fruit peeling and arils separation are the main motivations of progressive ready-to-eat pomegranate fresh arils industry. Also, extracted pomegranate arils are highly perishable due to water loss and microbial contamination expose. The aim of the current work was then to evaluate the effect of ultrasound for 15 and 30 min on maintenance of bioactive compounds and microbial load reduction of pomegranate arils cv. Rabbab. Treated arils were kept at 5 °C and analyzed during 15 days of storage. The most and least weight loss of arils obtained in control and 30 min treated samples, respectively. After 12 days of storage, all samples were decayed except those treated for 15 and 30 min. The ultrasound treatment significantly prevented degradation of anthocyanin and ascorbic acid compounds. Total phenol and antioxidant activity decreased during storage. At the end of storage, the most total phenol content (3898.6 mg GAE L⁻¹) was found in arils treated for 30 min whereas the most anthocyanin (91.93 mg L⁻¹), total antioxidant activity (82.65%), and ascorbic acid (2.53 mg L⁻¹) were found in arils treated for 15 min. Ultrasound treated arils had lower microbial load (total mesophilic bacteria in control and 30-min treated samples) in each stage during storage. At the end of storage, the microbial load in treated and control arils was 0.7 and 0.2 Log CFU g⁻¹, respectively). Overall, ultrasound treatment effectively reduced weight loss and preserved bioactive compounds during storage.     

A waveguide high-pass filter system for measuring the spectrum of pulsed terahertz sources

We propose a system for measuring spectra of terahertz (THz) pulses, including single pulses, which is based on high-pass filters (HPFs). The system consists of channels for measuring amplitudes of pulses (initial pulses and those transmitted via HPFs with different cutoff frequencies) and an algorithm for processing of the obtained data. The pulse spectrum is restored by using the iteration method or the amplitude–frequency method. The iteration method of spectrum restoration is applicable in the range of THz pulse durations from 10⁻⁹ s to 10⁻⁷ s. The amplitude–frequency method is applicable to THz pulses with durations exceeding 10⁻⁸ s. The system for measuring of THz pulse spectra was simulated by using the characteristics of specially developed waveguide HPFs. The relative simulation error of determining the central frequency by the amplitude–frequency method is equal to 2 · 10⁻⁶ for THz pulse durations of 10⁻⁵ s and longer.     

LDH of NiZnFe and its composites with carbon nanotubes and data-palm biochar with efficient adsorption capacity for RB5 dye from aqueous solutions: Isotherm,kinetic, and thermodynamics studies

In the study, the layered double hydroxide (LDH) of NiZnFe and its composites with date-palm biochar (LDH-DPb) and carbon nanotubes (LDH-cnt) were synthesized for adsorbing reactive black 5 (RB5) dye from aqueous solutions. In the first 5 min, rapid adsorption was followed by a gradual increase in both dye uptake and removal efficiency of up to 60 min of starting time. In the investigated pH range (3.0–8.0), the removal efficiency linearly decreased while the sorption capacity linearly increased for all three adsorbents as their doses increased to 0.3 or 0.4 g following a decreasing trend up to 0.6 g. By increasing the initial RB5 concentration from 10 to 100 mg L⁻¹, the removal efficiency linearly decreased. A nearly perfect fitting of the pseudo-second-order kinetic model to the adsorption data was observed; however, the Elovich kinetic model showed the heterogeneous surface of adsorbents with chemisorption. At the solid–liquid interface, from a thermodynamics point of view, we obtained the nonspontaneous nature of the adsorption of RB5 dye of the studied adsorbents with an increased disorder, which supported the endothermic nature onto the studied adsorption process. Furthermore, a nearly perfect fitting of the Langmuir model was obtained to the adsorption data, thereby suggesting the monolayer adsorption of RB5 dye onto the studied adsorbents. In the Dubinin–Radushkevich model, a good agreement of the calculated adsorption capacities to the experimental values were observed and the chemical adsorption of RB5 dye on to the studied adsorbents was proposed based on E (8 – 16 kJ mol⁻¹).     

High-efficient liquid exfoliation of 2D metal-organic framework using deep-eutectic solvents

The exfoliation of bulk two-dimensional metal–organic framework (MOF) into few-layered nanosheets has attracted much attention recently. In this work, an environmental-friendly route has been developed for layered-MOF (MAMS-1) delamination using deep eutectic solvent (DES), which is more sustainable and efficient alternative than conventional organic solvents for MOF nanosheet preparation. Under sonication condition, DES as solvents, the highest exfoliation rate of MAMS-1 is up to 70% with two host layers via poly(vinylpyrrolidone) (PVP) surfactant-assisted method. The presence of tert-butyl exteriors and the atomically thickness endow the MOF nanosheets stable suspension for at least one month. Due to the 2D structure and excellent stability, MAMS-1 nanosheet (MAMS-1-NS) was chosen as a good candidate to encapsulate Eu³⁺ cations. The obtained Eu³⁺@MAMS-1-NS acts as a multi-responsive luminescent sensor through fluorescence quenching, and can specifically recognize Fe³⁺ (LOD = 0.40 μM, K_SV = 1.05 × 10⁵ M^−l), Hg²⁺ (LOD = 0.038 μM, K_SV = 5.78 × 10⁶ M^−l), Cr₂O₇²⁻ (LOD = 0.33 μM, K_SV = 1.55 × 10⁵ M^−l) and MnO₄⁻ (LOD = 0.088 μM, K_SV = 4.49 × 10⁵ M^−l). Compared with bulk Eu³⁺@MAMS-1, the sensitivity of Eu³⁺@MAMS-1-NS is greatly improved owing to its ultrathin nanosheet morphology and highly accessible active sites on the surface.     

Controllable synthesis of layered Co–Ni hydroxide hierarchical structures for high-performance hybrid supercapacitors

A facile solvothermal method is developed for synthesizing layered Co–Ni hydroxide hierarchical structures by using hexamethylenetetramine (HMT) as alkaline reagent. The electrochemical measurements reveal that the specific capacitances of layered bimetallic (Co–Ni) hydroxides are generally superior to those of layered monometallic (Co, Ni) hydroxides. The as-prepared Co_0.5Ni_0.5 hydroxide hierarchical structures possesses the highest specific capacitance of 1767 F g⁻¹ at a galvanic current density of 1 A g⁻¹ and an outstanding specific capacitance retention of 87% after 1000 cycles. In comparison with the dispersed nanosheets of Co–Ni hydroxide, layered hydroxide hierarchical structures show much superior electrochemical performance. This study provides a promising method to construct hierarchical structures with controllable transition-metal compositions for enhancing the electrochemical performance in hybrid supercapacitors.     

Ionic liquid gating control of magnetic anisotropy in Ni0.81Fe0.19 thin films

Voltage control magnetism is one of the most energy efficient pathway towards magnetoelectric (ME) device. Ionic liquid gating (ILG) method has already shown impressive manipulation power at the IL/electrode interface to influence the structure, orbital as well as spin of the electrode materials. As key material in anisotropy magnetoresistance sensor and spin valve heterostructure, the permalloy Ni_0.81Fe_0.19 was utilized as the electrode to investigate the ILG induced magnetic anisotropy change. In this work, we realized magnetic anisotropy control in Au/[DEME]⁺[TFSI]^-/Ni_0.81Fe_0.19 (2.5 nm)/Ta heterostructure via ILG caused electrostatic doping. This is evidenced in situ reversible ferromagnetic field (H_r) shift with electron spin resonance (ESR) spectrometer. Aiming at the question whether the charge accumulation at the ionic liquid interface is the main control mechanism at low voltage, we carefully tested the relationship between the change of resonance field and the amount of surface charge. It was found that these two had a good linear relationship between −1 V and +1 V. Defining the linear parameter as A whose value is 28.7 mT m²/Col. Unlike previously reported chemical regulation of Co, this article used ionic liquids to physically regulate NiFe, which has not been studied in the previous ionic liquid regulation. And NiFe has a narrower resonance line width for easy reference to microwave devices. In addition, It also has a stronger ferromagnetic signal than Co, which can be more easily detected as a sensor device. Therefore, this system is more promising. The ILG control NiFe may lead to a new kind of magnetoelectric sensor devices and path a new way to low energy consumption spintronics.     

Nanofibrous membrane of polyacrylonitrile with efficient adsorption capacity for cadmium ions from aqueous solution: Isotherm and kinetic studies

The nanofibrous membrane of polyacrylonitrile (NMP) was successfully synthesized after NaOH and NaHCO₃ treatment aiming its functionalization using electrospinning for cadmium ion (Cd²⁺) adsorption. Field emission scanning electron microscopy (FE-SEM) revealed that small particles attached to the surface of functionalized PAN nanofibers. Equilibrium was attained after 60 min following a rapid uptake of Cd²⁺ with maximum adsorption capacity and percentage removal at an optimum solution pH of 7.0. The adsorbent dose of 0.3 g and 90 mg L⁻¹ of initial Cd²⁺ concentration yielded the maximum adsorption capacity. The pseudo-second-order kinetic model was the best fitted to the adsorption data, indicating that the chemisorption is the controlling mechanism of adsorption. The physisorption was proposed based on the calculated values of the mean free energy of adsorption from the D–R isotherm (E < 8 kJ mol⁻¹). Furthermore, three-parameter isotherm models indicated the homogeneous and heterogeneous Cd²⁺ adsorption onto NMP adsorbent.     

Ultrasound-assisted depolymerization of kappa-carrageenan and characterization of degradation product

Degradation of polysaccharides to afford low-molecular-weight oligosaccharides have been shown to produce new bioactivities that are not present in the starting material. The simplicity of ultrasonic treatment in the degradation of a polysaccharide, such as κ-carrageenan, offers practical advantage in producing degraded products with lower molecular weight that may have new interesting potential activities. This study embarked on investigating the effects in molecular weights and structural changes of κ-carrageenan under varying ultrasonic conditions. Molecular weight (MW) monitoring of ultrasonically-treated κ-carrageenan at various conditions were done by gel permeation chromatography. The product formed using the optimized condition was characterized using FTIR and NMR. The decrease in MW has been shown to be dependent on low concentration (5.0 mg mL⁻¹), high amplitude (85%), and long treatment time (180 mins) to afford a degraded κ-carrageenan with average molecular weight (AMW) of 41,864 Da, which is a 96.33% reduction from the raw sample with initial AMW of 1,139,927 Da. Structural analysis reveals that most of the peaks of the raw κ-carrageenan was retained with minor change. 1D and 2D NMR analyses showed that the sonic process afforded a product where the sulfate group at the G4S-4 position was cleaved forming a methylene in the G4S ring. The results would be useful in the structure–activity relationship of κ-carrageenan oligosaccharides and in understanding the effect in the various potential applications of degraded κ-carrageenan.     

Improving the signal amplitude of meandering coil EMATs by using ribbon soft magnetic flux concentrators (MFC)

This paper presents a new method of improving the ultrasonic signal amplitude from a meander line EMAT by using soft magnetic alloy ribbon (Fe₆₀Ni₁₀V₁₀B₂₀) as a magnetic flux concentrator (MFC). The flux concentrator is a thin soft amorphous magnetic material (Fe₆₀Ni₁₀V₁₀B₂₀) which is very sensitive to a small flux change. The MFC is used with the EMAT to improve the signal amplitude and it was observed that the peak signal amplitude increases by a factor of two compared to the signal without MFC. Two dimensional numerical models have been developed for the EMAT with MFC to quantify the improvement of the received signal amplitudes. Model calculations and experiments have been carried out for a wide range of ultrasonic frequencies (500 kHz-1 MHz) in different materials.     

Determination of the β-Glucosidase Activity in Different Soils by Pre Capillary Enzyme Assay Using Capillary Electrophoresis with Laser-Induced Fluorescence Detection

Enzyme activities can provide indication for quantitative changes in soil organic matter (SOM). It is known that the activities of most enzymes increase as native SOM content reflecting larger microbial communities and stabilization of enzymes on humic materials. β-Gucosidase (β-Glu) activities have been frequently used as indicators of changes in quantity and quality of SOM. In this study we propose a simple and very sensitive method, which has lower limit of detection compared with classic spectrophotometric method with the aim of determinate the β-Glu activity in soil samples using Fluorescein mono-β-D-glucopyranoside (FMGlc) as a substrate. The fluorescein released by the enzymatic reaction was quantified by capillary electrophoresis-laser induced fluorescence (CE-LIF) method. The background electrolyte (BGE) consisted in 40 mM phosphate buffer, pH 6. The LOD and LOQ for fluorescein were 1.3 10⁻⁷ mg mL⁻¹ and 6.4 10⁻⁶ mg mL⁻¹, respectively. This work deals with the minimization of the mixture for the enzymatic reaction and with the optimization conditions of CE separation. To the best of our knowledge, this is the first time that an enzymatic activity was detected in soil using CE-LIF system.     

Elaboration and electrochemical characterization of LaZr2Cr4Ni5-based metal hydride alloys

The elaboration of LaZr₂Cr₄Ni₅-based intermetallic compound was performed by mechanical alloying from LaNi₅ and ZrCr₂ precursors and characterized as active materials of negative electrodes in nickel-metal hydride (Ni-MH) batteries. The effect of the milling duration on the phase composition was investigated. The structural properties of the formed phases were determined by X-ray diffraction and quantified from the Rietveld refinement data. The increase of the milling time up to 40 h leads to the highest abundance of the LaZr₂Cr₄Ni₅ phase, estimated at a weight content of 60.6 %, and a complete elimination of the LaNi₅ intermetallic precursor. The chronopotentiometry, cyclic voltammetry, and chronoamperometry techniques were applied to characterize the electrochemical behavior of prepared LaZr₂Cr₄Ni₅-based compounds. The maximum discharge capacity was 152 mAh g⁻¹, and a high electrochemical stability was obtained in the alkaline solution. The value of the hydrogen diffusion coefficient is equal to 2.1 × 10⁻⁸ cm² s⁻¹, reflecting an appropriate electrochemical hydrogenation kinetic in the LaZr₂Cr₄Ni₅-based compounds.