Assembly of Pt nanoparticles on electrospun In2O3 nanofibers for H2S detection

In this paper, we presented a simple and effective solution route to deposit Pt nanoparticles on electrospun In₂O₃ nanofibers for H₂S gas detection. The morphology and chemical structure of the as-prepared samples were analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and X-ray photoelectron spectra (XPS). The results showed that large quantities of In₂O₃ nanofibers with diameters about from 60 to 100 nm were obtained and the surface of them was decorated with Pt nanoparticles (5–10 nm in size). The In₂O₃ nanofibers decorated by Pt nanoparticles exhibited excellent gas sensing properties to H₂S, such as high sensitivity, good selectivity and fast response at relatively low temperature.     

Fabrication of mesoporous SiO2–C–Fe3O4/γ–Fe2O3 and SiO2–C–Fe magnetic composites

A synthetic method for the fabrication of silica-based mesoporous magnetic (Fe or iron oxide spinel) nanocomposites with enhanced adsorption and magnetic capabilities is presented. The successful in situ synthesis of magnetic nanoparticles is a consequence of the incorporation of a small amount of carbon into the pores of the silica, this step being essential for the generation of relatively large iron oxide magnetic nanocrystals (10 ± 3 nm) and for the formation of iron nanoparticles. These composites combine good magnetic properties (superparamagnetic behaviour in the case of SiO₂–C–Fe₃O₄/γ–Fe₂O₃ samples) with a large and accessible porosity made up of wide mesopores (>9 nm). In the present work, we have demonstrated the usefulness of this kind of composite for the adsorption of a globular protein (hemoglobin). The results obtained show that a significant amount of hemoglobin can be immobilized within the pores of these materials (up to 180 mg g⁻¹ for some of the samples). Moreover, we have proved that the composite loaded with hemoglobin can be easily manipulated by means of an external magnetic field.     

Kinetics of adsorption of Saccharomyces cerevisiae mandelated dehydrogenase on magnetic Fe3O4–chitosan nanoparticles

The adsorption of Saccharomyces cerevisiae mandelated dehydrogenase (SCMD) protein on the surface-modified magnetic nanoparticles coated with chitosan was studied in a batch adsorption system. Functionalization of surface-modified magnetic particles was performed by the covalent binding of chitosan onto the surface of magnetic Fe₃O₄ nanoparticles. Characterization of these particles was carried out using FTIR spectra, transmission electron micrography (TEM), X-ray diffraction (XRD) and vibrating sample magnetometry (VSM). Magnetic measurement revealed that the magnetic Fe₃O₄–chitosan nanoparticles were superparamagnetic and the saturation magnetization was about 37.3 emu g⁻¹. The adsorption capacities and rates of SCMD protein onto the magnetic Fe₃O₄–chitosan nanoparticles were evaluated. The adsorption capacity was influenced by pH, and it reached a maximum value around pH 8.0. The adsorption capacity increased with the increase in temperature. The adsorption isothermal data could be well interpreted by the Freundlich isotherm model. The kinetic experimental data properly correlated with the first-order kinetic model, which indicated that the reaction is the adsorption control step. The apparent adsorption activation energy was 27.62 kJ mol⁻¹ and the first-order constant for SCMD protein was 0.01254 min⁻¹ at 293 K.     

Synthesis of Co/MFe2O4 (M=Fe, Mn) core/shell nanocomposite particles

Monodispersed cobalt nanoparticles (NPs) with controllable size (8–14 nm) have been synthesized using thermal decomposition of dicobaltoctacarbonyl in organic solvent. The as-synthesized high magnetic moment (125 emu/g) Co NPs are dispersible in various organic solvents, and can be easily transferred into aqueous phase by surface modification using phospholipids. However, the modified hydrophilic Co NPs are not stable as they are quickly oxidized, agglomerated in buffer. Co NPs are stabilized by coating the MFe₂O₄ (M=Fe, Mn) ferrite shell. Core/shell structured bimagnetic Co/MFe₂O₄ nanocomposites are prepared with tunable shell thickness (1–5 nm). The Co/MFe₂O₄ nanocomposites retain the high magnetic moment density from the Co core, while gaining chemical and magnetic stability from the ferrite shell. Compared to Co NPs, the nanocomposites show much enhanced stability in buffer solution at elevated temperatures, making them promising for biomedical applications.     

Hydrothermal synthesis of monodisperse Fe3O4 nanoparticles based on modulation of tartaric acid

In this paper, monodisperse Fe₃O₄ nanoparticles with single crystalline structure were synthesized via a facile environment-friendly method. And the size of the nanoparticles ranges from 10 nm to 15 nm. As-synthesized Fe₃O₄ were characterized by X-ray diffraction instrument (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FT-IR) spectrometer and field emission transmission electron microscope (FE-TEM). The effect of tartaric acid (TA) amount on products was investigated by XRD and TEM. The results indicated that TA could commendably modulate the crystalline phase, morphology and size of nanometer Fe₃O_4. A possible generated mechanism of Fe₃O₄ crystals was proposed in virtue of UV–vis absorption spectra. Besides, the magnetic properties of as-synthesized Fe₃O₄ were detected.     

Fabrication,characterization and X-band microwave absorption properties of PAni/Fe3O4/PVA nanofiber composites materials

This work presents a study of microwave absorption properties of PAni/Fe₃O₄/PVA nanofiber composites with different ratio of Fe₃O₄ nanoparticles. The morphology of the composites nanofibers study by Field Emission Scanning Electron Microscopes (FESEM) and Transmission Electron Microscope (TEM) showed that the low content of Fe₃O₄ nanoparticles presence in the composites nanofibers indicates very much uniform surface, in the composites nanofiber without many bends, but some bends develop at higher content of Fe₃O₄ nanoparticles as indicated in the TEM image. Image-J software was used to further investigate the diameter of the composites nanofiber and found to be in the range of 152 to 195 nm. The nanofiber composites show excellent electric and magnetic properties and therefore vary with the addition of Fe₃O₄ nanoparticles in the composites nanofiber. In addition the PAni/Fe₃O₄/PVA composites nanofibers were further characterized by X-ray diffraction spectra (XRD) and Four Transformation infrared spectra (FTIR). The XRD pattern shows the presence of PAni nanotubes containing Fe₃O₄ nanoparticles by indicating peaks at 23.4⁰ and 35.43⁰ which was further supported by FTIR analysis. Microwave vector network analyzers (MVNA) were used to estimate the microwave absorption properties of the composites nanofibers. The absorption parameters was found to be −6.4 dB at 12.9 GHz within the range of X-band microwave absorption frequency, this reflection loss is attributed to the multiple absorption mechanisms as a result of the improved of impedance matching between dielectric and magnetic loss of the absorbent materials demonstrating that these materials can be used as protective material for electromagnetic radiation.     

Electrochemical activity of nanocrystalline Fe3O4 in aprotic Li and Na salt electrolytes

Fe₃O₄ powders, whose average particle sizes were 400 nm, 100 nm, and 10 nm in diameter, were prepared in order to investigate the effect of particle size on their electrochemical activity. X-ray diffraction and electron microscopy measurements confirmed that all the prepared samples were identified as inverse-spinel type Fe₃O₄, whose crystallite/particle sizes were between 400 nm and 10 nm. We found that the electrochemical activity of Fe₃O₄ in a lithium salt electrolyte was enhanced with a decrease in the particle size from 400 nm to 10 nm. The 10 nm nanocrystalline Fe₃O₄ powder demonstrated the high discharge capacities of about 130 and 160 mAh g⁻¹ with a satisfactory capacity retention as the active cathode material of Li and Na batteries, respectively.     

An investigation on polycaprolactone/chitosan/Fe3O4 nanofibrous composite used for hyperthermia

Hyperthermia is considered as an effective supplementary cancer treatment. However, the uneven temperature distribution is the major challenge in hyperthermia. Nanotechnology could solve this problem by applying magnetic nanoparticles directly or in nanofibers as implants. Low solubility, poor cancer targeting, and leakage are limitations of free magnetic nanoparticles. In this work, Fe₃O₄ nanoparticles were loaded into polycaprolactone/chitosan blended nanofibers in various contents. Magnetic, chemical, physical, and morphology of the derived nanofibrous composites were then studied. The results showed the magnetic properties of the nanocomposite had low coercivity, which was close to superparamagnetic particles. Chemical analysis showed that components had no interaction with each other. Nevertheless, Fe₃O₄ was slightly transformed to other iron oxides. However, the magnetic analysis showed this transformation had no significant effect on final magnetic content of the nanofibers. The results of X‐ray diffraction (XRD) (19.5 nm), transmittance electron microscopy (TEM) (21.6 nm), and vibration sample magnetometer (VSM) (17 nm) suggested that the magnetic nanoparticles were single domain. Thermal analysis results showed that 7% Fe₃O₄ nanofibers had more heat increase as oppose to other nanofibrous composites in the alternative magnetic field (AMF). Nonetheless, the heat performance of 3% Fe₃O₄ nanofibers was more than others according to its specific power absorption (SPA). Therefore, due to the importance of using nanoparticles in the least possible content, this method can be used as a postsurgical treatment by applying these nanofibrous composites as implants on the tumor site. Moreover, these nanofiber composites could carry anticancer drugs, which are applied as a multi‐mode treatment system.     

磁靶向纳米Fe3O4-TiO2复合物的制备及其对肝癌细胞的光催化杀伤效应

采用三种低温溶胶-凝胶法制备了具有不同Fe₃O₄掺杂量的磁靶向纳米Fe₃O₄-TiO₂复合物, 通过X射线衍射(XRD)、透射电镜(TEM)、傅里叶变换红外(FTIR)光谱、紫外-可见(UV-Vis)光谱、荧光光谱(FS)及磁性能分析等表征方法筛选出包覆均匀、分散性好、磁性能优异及光催化活性较高的纳米Fe₃O₄-TiO₂复合物. 以四甲基偶氮唑蓝(MTT)法检测肝癌细胞(HepG2)的存活率, 考察纳米Fe₃O₄-TiO₂复合物在外磁场作用下对HepG2 细胞的光催化杀伤效应. 结果表明: 采用方法三制备的5%(质量分数)Fe₃O₄-TiO₂复合物具备核-壳结构, 在混悬液中分散性较好, 平均粒径约为50 nm, 具有较强的光催化活性和良好的磁响应性, 同时将纳米TiO₂的光响应范围拓宽至444 nm; 在外磁场作用下, 紫外光和可见光激发纳米Fe₃O₄-TiO₂复合物对HepG2细胞的杀伤效应差异不大, 且均强于纳米TiO₂; 其杀伤效应在0-1.0 T范围内随着外磁场强度的增大而增强.     

可循环磁性Pt/Fe3O4-MCNT催化剂上的肉桂醛选择性加氢反应

采用多步法依次将制备的Fe₃O₄纳米颗粒和Pt纳米颗粒负载到多壁碳纳米管(MCNT)上得到Pt/Fe₃O₄-MCNT磁性催化剂,以X射线衍射(XRD)、透射电镜(TEM)、超导量子干涉磁强计(SQUID)和热重-差热分析(TG-DTA)对Pt/Fe₃O₄-MCNT磁性催化剂的结构和磁性质进行了表征。研究发现预制备的Fe₃O₄纳米颗粒与Pt纳米颗粒均匀地分散于MCNT上,新制备以及多次使用后的Pt/Fe₃O₄-MCNT室温下都具有良好的超顺磁性。研究了Pt/Fe₃O₄-MCNT磁性催化剂上的肉桂醛选择性加氢反应,结果显示催化剂具有良好的C=O加氢活性,肉桂醛转化率在50%左右时,肉桂醇选择性可达96%以上。尺寸均一的Pt粒子均匀的分散在催化剂上可能是催化剂具有良好的C=O加氢选择性的重要原因。在外加磁场作用下催化剂可以高效地从液相反应体系中分离,经多次循环使用后仍具有良好的催化性能。     

纳米Fe_3O_4及钴离子掺杂Fe_3O_4:有机碱共沉淀制备和磁性质

以有机碱四甲基氢氧化铵(TMAH)为沉淀剂合成了纳米Fe3O4和Co2+掺杂的纳米Fe3O4粒子。分别讨论了碱用量,铁盐溶液浓度,反应温度,有机碱及PEG-4000的分散性等因素对纳米Fe3O4的形貌影响。结果表明,所合成的纳米Fe3O4为30nm左右的反尖晶石型面心立方结构,有机碱除了起沉淀剂作用,还能够提高纳米Fe3O4的分散性。本文还讨论了不同Co2+掺入量的纳米Fe3O4粒子的磁性质,结果表明Co2+掺杂的纳米Fe3O4粒子的矫顽力在不同掺入量的下有较大的改变。当Co2+掺入量为10.0%时,纳米Fe3O4的矫顽力达到最大值,为1628Oe。     

可循环磁性Pt/Fe_3O_4-MCNT催化剂上的肉桂醛选择性加氢反应

采用多步法依次将制备的Fe3O4纳米颗粒和Pt纳米颗粒负载到多壁碳纳米管(MCNT)上得到Pt/Fe3O4-MCNT磁性催化剂,以X射线衍射(XRD)、透射电镜(TEM)、超导量子干涉磁强计(SQUID)和热重-差热分析(TG-DTA)对Pt/Fe3O4-MCNT磁性催化剂的结构和磁性质进行了表征。研究发现预制备的Fe3O4纳米颗粒与Pt纳米颗粒均匀地分散于MCNT上,新制备以及多次使用后的Pt/Fe3O4-MCNT室温下都具有良好的超顺磁性。研究了Pt/Fe3O4-MCNT磁性催化剂上的肉桂醛选择性加氢反应,结果显示催化剂具有良好的C=O加氢活性,肉桂醛转化率在50%左右时,肉桂醇选择性可达96%以上。尺寸均一的Pt粒子均匀的分散在催化剂上可能是催化剂具有良好的C=O加氢选择性的重要原因。在外加磁场作用下催化剂可以高效地从液相反应体系中分离,经多次循环使用后仍具有良好的催化性能。     

Surface modified Fe3O4 nanoparticles as a protein delivery vehicle

We report a one-step synthesis of Fe₃O₄ nanoparticles coated with PEG. The formation of the Fe₃O₄ core and the polymer coating took place simultaneously. Furthermore, these nanoparticles were modified with 3-APTES, providing a -NH₂ functional group, and applied in the immobilization of lysozyme. In this paper, the modified magnetic nanoparticles acting as a general agent to immobilize proteins are around 10 nm in size. The protein immobilization can be adjusted flexibly by changing either the amount of glutaraldehyde or the buffer solution.     

Porous cobalt oxide (Co3O4) nanorods: Facile syntheses, optical property and application in lithium-ion batteries

We developed a facile synthetic route of porous cobalt oxide (Co₃O₄) nanorods via a microemulsion-based method in combination with subsequent calcination process. The porous structure was formed by controlled decomposition of the microemulsion-synthesized precursor CoC₂O₄ nanorods without destruction of the original morphology. The as-prepared Co₃O₄ nanorods, consisting of small nanoparticles with diameter of 80–150 nm, had an average diameter of 200 nm and a length of 3–5 μm. The morphology and structure of synthesized samples were characterized by transmission electron microscopy and scanning electron microscopy. The phase and composition were investigated by X-ray powder diffraction and X-ray photoelectron spectroscopy. The optical property of Co₃O₄ nanorods was investigated. Moreover, the porous Co₃O₄ nanorods exhibited high electrochemical performance when applied as cathode materials for lithium-ion batteries, which gives them good potential applications.     

Synthesis, crystal structure and characterization of iron pyroborate (Fe2B2O5) single crystals

Single crystals of iron(II) pyroborate, Fe₂B₂O₅, were prepared at 1000–1050 °C under an argon atmosphere. The crystals were transparent, yellowish in color and needle-like or columnar. The crystal structure of Fe₂B₂O₅ was analyzed by single-crystal X-ray diffraction. Refined triclinic unit cell parameters were a=3.2388(2), b=6.1684(5), c=9.3866(8) Å, α=104.613(3)°, β=90.799(2)° and γ=91.731(2)°. The final reliability factors of refinement were R1=0.020 and wR2=0.059 [I > 2σ(I)]. Transmittance over 50% in the visible light region from 500 to 750 nm was observed for a single crystal of Fe₂B₂O₅ with a thickness of about 0.3 mm. The light absorption edge estimated from a diffuse reflectance spectrum was at around 350 nm (3.6 eV). Magnetic susceptibility was measured for single crystals at 4–300 K. Fe₂B₂O₅ showed antiferromagnetic behavior below the Néel temperature, T_N≈70 K, and the Weiss temperature was T_W=36 K. The effective magnetic moment of Fe was 5.3μ_B.     

Development of Fe3O4-poly(l-lactide) magnetic microparticles in supercritical CO2

The Fe₃O₄-poly(l-lactide) (Fe₃O₄-PLLA) magnetic microparticles were successfully prepared in a process of solution-enhanced dispersion by supercritical CO₂ (SEDS), and their morphology, particle size, magnetic mass content, surface atom distribution and magnetic properties were characterized. Indomethacin (Indo) was used as a drug model to produce drug-polymer magnetic composite microparticles. The resulting Fe₃O₄-PLLA microparticles with mean size of 803 nm had good magnetic property and a saturation magnetization of 24.99 emu/g. The X-ray photoelectron spectroscopy (XPS) test indicated that most of the Fe₃O₄ were encapsulated by PLLA, which indicated that the Fe₃O₄-PLLA magnetic microparticles had a core–shell structure. After further loading with drug, the Indo-Fe₃O₄-PLLA microparticles had a bigger mean size of 901 nm, and the Fourier transform infrared spectrometer (FTIR) analysis demonstrated that the SEDS process was a typical physical coating process to produce drug-polymer magnetic composite microparticles, which is favorable for drugs since there is no change in chemistry. The in vitro cytotoxicity test showed that the Fe₃O₄-PLLA magnetic microparticles had no cytotoxicity and were biocompatible, which means there is potential for biomedical application.     

用于高效去除水中孔雀石绿的三层结构磁性复合材料Fe3O4@聚丙烯酸@ZiF-8的制备

设计并合成了一种以磁性纳米粒子为核,聚合物为中间层,金属有机骨架材料为外层的三层结构磁性复合材料(Fe₃O₄@PAA@ZIF-8)。首先利用溶剂热法制备Fe₃O₄纳米粒子,然后通过蒸馏沉淀聚合法在Fe₃O₄纳米粒子表面包覆聚丙烯酸(PAA)层,最后通过原位沉积法在PAA外部包覆ZIF-8。在对Fe₃O₄@PAA@ZIF-8的组成和结构进行表征的基础上,深入研究其对孔雀石绿(MG)的吸附性能。透射电子显微镜(TEM)显示Fe₃O₄@PAA@ZIF-8具有明显的三层结构,Fe₃O₄的平均粒径为117nm,PAA层厚度约为17 nm,ZIF-8层的厚度约为14 nm。Fe₃O₄@PAA@ZIF-8对MG的吸附量随着p H的升高而增大,吸附过程符合准二阶动力学模型和Langmuir等温吸附模...     

Chitosan–iron oxide nanobiocomposite based immunosensor for ochratoxin-A

The rabbit immunoglobulin antibodies (IgGs) have been immobilized onto nanobiocomposite film of chitosan (CH)–iron oxide (Fe₃O₄₎ nanoparticles prepared onto indium–tin oxide (ITO) electrode for detection of ochratoxin-A (OTA). Excellent film forming ability and availability of –NH₂ group in CH and affinity of surface charged Fe₃O₄ nanoparticles for oxygen support the immobilization of IgGs. Differential pulse voltammettry (DPV) studies indicate that Fe₃O₄ nanoparticles provide increased electroactive surface area for loading of IgGs and improved electron transport between IgGs and electrode. IgGs/CH–Fe₃O₄ nanobiocomposite/ITO immunoelectrode exhibits improved characteristics such as low detection limit (0.5 ng dL⁻¹), fast response time (18 s) and high sensitivity (36 μA/ng dL⁻¹ cm⁻²) with respect to IgGs/CH/ITO immunoelectrode.     

用于高效去除水中孔雀石绿的三层结构磁性复合材料Fe3O4@聚丙烯酸@ZiF-8的制备

设计并合成了一种以磁性纳米粒子为核，聚合物为中间层，金属有机骨架材料为外层的三层结构磁性复合材料(Fe₃O₄@PAA@ZIF 8)。首先利用溶剂热法制备Fe₃O₄纳米粒子，然后通过蒸馏沉淀聚合法在Fe₃O₄纳米粒子表面包覆聚丙烯酸(PAA)层，最后通过原位沉积法在PAA外部包覆ZIF 8。在对Fe₃O₄@PAA@ZIF 8的组成和结构进行表征的基础上，深入研究其对孔雀石绿(MG)的吸附性能。透射电子显微镜(TEM)显示 Fe₃O₄@PAA@ZIF 8 具有明显的三层结构，Fe₃O₄的平均粒径为 117nm，PAA 层厚度约为 17 nm，ZIF 8层的厚度约为 14 nm。Fe₃O₄@PAA@ZIF 8对 MG 的吸附量随着 pH 的升高而增大，吸附过程符合准二阶动力学模型和 Langmuir等温吸附模型。此外，Fe₃O₄@PAA@ZIF 8还表现出良好的重复利用性能，8次循环利用后对MG(500 mg·L^-1)的最大吸附量仍可达982 mg·g^-1。     

Novel fabrication of magnetic thermoplastic nanofibers via melt extrusion of immiscible blends

A novel technique of fabricating magnetic thermoplastic nanofibers by the control of the phase separation of immiscible polymer blends during melt extrusion was presented. The magnetic poly(vinyl alcohol‐co‐ethylene) (PVA‐co‐PE)/Fe₃O₄ composite nanofibers were prepared via the melt extrusion of cellulose acetate butyrate matrix and PVA‐co‐PE preloaded with different amounts of Fe₃O₄ nanoparticles. The morphologies of magnetic composite nanofibers were characterized by scanning electron microscopy. The uniform dispersion of Fe₃O₄ nanoparticles in nanofiber matrixes and crystal structures were confirmed using transmission electron microscopy and wide angle X‐ray diffraction. Thermogravimetric analysis was employed to quantify the exact loading amount of Fe₃O₄ nanoparticles in the composite nanofibers. The magnetic measurements showed that composite nanofibers displayed superparamagnetic behavior at room temperature. With increasing content of Fe₃O₄ nanoparticles, the saturation magnetization of the magnetic composite nanofiber significantly improved. The prepared magnetic composite nanofibers might have found potential applications in the sensors and bio‐molecular separation fields. Copyright © 2012 John Wiley & Sons, Ltd.