Gallery structure and exfoliation of organophilized montmorillonite: effect on composite properties

Wyoming montmorillonite was organophilized to different extents with N-cetylpyridinium chloride and its gallery structure was studied by WAXS. PP nanocomposites were prepared using this silicate and their structure, as well as tensile properties were determined as a function of composition. Two peaks were observed in the WAXS patterns of some of the treated silicates, one of which disappeared during processing. The orientation of the organic compound in the galleries depends on its size and amount, as well as on the ion density of the filler. Multiple peaks appearing in the WAXS pattern of organophilized silicate may arise from interference, but they may also indicate the presence of several populations of layer distances. Water is absorbed between the galleries of partially organophilized silicates leading to the separation of the layers resulting in the appearance of new scattering peaks. Exfoliation occurs only above a critical gallery distance, which corresponds to the thickness of two aliphatic chains. Although exfoliation of the silicate is determined by its organophilization and gallery structure, composite properties are dominated by interfacial interaction.     

聚苯乙烯/蒙脱土熔融插层复合的研究

用熔融法制备了聚苯乙烯／蒙脱土插层复合材料，用Ｘ 射线衍射、ＤＳＣ等手段研究了复合材料的结构与性能．聚苯乙烯熔体不能插层于钠基蒙脱土中，但能插层于经有机化合物处理过的蒙脱土中．     

Thermo-oxidative stability of polypropylene/layered silicate nanocomposites

Several series of experiments were carried out to check the effect of components on the stability of PP/layered silicate nanocomposites. The amount of organophilic montmorillonite (OMMT) changed between 0 and 6, while that of maleated polypropylene (MAPP) between 0 and 50 vol%. The composites were prepared in an internal mixer at 190 °C. Mixing speed and time were changed to study the effect of processing conditions on stability. The structure of the samples was characterised by various methods, while stability by the induction time of oxidation (OIT), the onset temperature of degradation (OOT) and by colour. Contrary to numerous claims published in the literature, which indicate the positive effect of layered silicates on the stability of polymer nanocomposites, our results clearly proved that both OMMT and MAPP accelerate degradation during processing and deteriorate the properties of PP composites. Residual stability decreases drastically with increasing amounts of both components, chain scission leads to the decrease of viscosity and to inferior strength and deformability. In spite of expectations, the effect of the components is independent of each other. Discoloration is caused mainly by the inherent colour of the filler and it decreases with increasing exfoliation. The most probable reason for decreased stability is the reaction of the components with the stabilisers, but this explanation needs further verification. Processing conditions influence degradation considerably, increasing shear rate and longer residence times lead to more pronounced degradation. The basic stabilization of commercial grade polypropylenes is insufficient to protect the polymer against degradation and without additional stabilization processing under normal conditions results in products with inferior quality.     

Comparative analysis of nanocomposites based on polypropylene and different montmorillonites

Nanocomposites of polypropylene (PP) were prepared by melt mixing using maleic anhydride modified polypropylene (PPg) and different organophilic montmorillonites (OMMT). The selected organo-modified clays differ in their initial particle size, amount and type of surfactant and/or their cation-exchange capacity. All composites have 80, 15 and 5 wt% of PP, PPg and OMMT, respectively. The materials were characterized using TGA, XRD, SEM and rotational rheometry. Cloisite 15A, Cloisite 93A, Nanomer I44 and a bentonite modified with octadecylammonium (B18) display intercalation and exfoliation after mixing and annealing and produce nanocomposites with different degrees of ‘solid-like’ rheological behavior. The composites based in Cloisite 15A and Nanomer I44, which use the same intercalant, show very similar phase structure and rheological response, regardless of the origin and initial characteristics of the clays. These nanocomposites are the most affected by the thermal history during rheological characterization in the molten state. On the other hand, Cloisite 10A and Cloisite 30B display collapse of the silicate layers after compounding with no evidence of exfoliation.     

A pulsed EPR study of surfactant layer structure in composites of a synthetic layered silicate with polystyrene and polycaprolactone

Double electron electron resonance (DEER), deuterium electron spin-echo envelope modulation (ESEEM) spectroscopy and 31P electron nuclear double resonance (ENDOR) spectroscopy were applied to site-specifically spin-labeled surfactants in the organically modified layered silicate magadiite and its composites with polystyrene (PS) and polycaprolactone (PCL). The organomagadiite consist of stacks of silicate platelets with surfactant layers between these platelets. In PS composites the stacks are dispersed in the polymer matrix as a whole, while melt processing with PCL leads to intercalation of polymer chains into the galleries between the platelets. The DEER data prove that even in the case of the non-intercalated PS composites the density of surfactant molecules changes drastically during composite formation on length scales of a few nanometers. Deuterium ESEEM data demonstrate that spin labels attached both in the middle and at the end of the alkyl chain have contact with the headgroups of neighboring surfactant molecules. By analysis of the 31P ENDOR spectra, two characteristic distances are found between the spin labels and the headgroups of phosphonium surfactants. The shorter, proximal distance can be assigned to headgroups in the same surfactant layer. By comparison with the basal spacing between consecutive silicate platelets the longer, distal distance is assigned to a layer of surfactants that is not attached to the surface of the next platelet but rather located between platelets. Altogether the data support a picture of trilayers of disordered surfactant molecules with their alkyl chains oriented nearly parallel to the surface.     

Preparation and Characterization of Poly(butyleneterephthalate)/Organoclay Nanocomposites

PBT/organic montmorillonite (MMT) nanocomposites were prepared via melt intercalation and their nanostructure was characterized by means of X‐ray diffraction and transmission electron microscopy. Nanocomposite formation requires sufficiently hydrophobic organically modified layered silicates, as well as the presence of polar interactions between silicate and polymer. Three different alkylammonium surfactants were used to modify MMT. In addition, epoxy resin was added as a third component, and the effects on the intercalation and exfoliation behavior of the PBT nanocomposites were investigated.     

Effect of interactions between the adsorbed species on the properties of single and mixed-surfactant monolayers at the air/water interface

Experimental data on surface tension available from the literature and generated in the present study are analyzed to estimate the applicability of adsorption models, based on the Frumkin equation, to nonionic and ionic surfactants and their mixtures. Optimization programs based on the least-squares method in media of Delphi V and Pascal VII are used. The effect of interactions between the adsorbed species on surface tension is considered in all cases. The results are compared to those obtained with the simpler Szyszkowski equation, employed in numerous studies of nonionic surfactants, when interactions are neglected. Cases where the Frumkin model can be successfully employed with ionic surfactants and mixtures are presented and the conditions of its applicability are analyzed. Related characteristic quantities (maximum adsorption, standard free energy of surfactant adsorption, energy of interaction between adsorbed species, standard free energy of counterion adsorption, degree of coverage by surfactant/counterion associates) are established as a function of: The properties of an adsorption layer from a mixture of nonionic and ionic surface-active species are compared to those of the single surfactants.     

Effects of organophilic clay on the solvent‐maintaining capability,dimensional stability,and electrochemical properties of gel poly(vinylidene fluoride) nanocomposite electrolytes

Four quaternary alkyl ammonium salts were used in an organophilic procedure, performed on montmorillonite clay, and resulted in intercalation in dimethylformamide (DMF) or ethylene carbonate (EC)/propylene carbonate (PC) as a cosolvent between poly(vinylidene fluoride) (PVdF) and the organophilic clay. An examination using X‐ray diffraction revealed that PVdF entered galleries of montmorillonite clay, and it exhibited exfoliation and intercalation phenomena when it was analyzed with transmission electron microscopy. Gel PVdF nanocomposite electrolyte materials were successfully prepared by the addition of the appropriate percentages of DMF or PC/EC as a cosolvent, organophilic clay, and lithium perchlorate to PVdF. The maximum ionic conductivity was 1.03 × 10^?2 S/cm, and the materials exhibited better film formation, solvent‐maintaining capability, and dimensional stability than electrolyte films without added organophilic clays. The results of cyclic voltammetry testing showed that the addition of the organophilic clays significantly enhanced the electrochemical stability of the polymer electrolyte system. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3873–3882, 2002     

Gas permeation and mechanical properties of polypropylene nanocomposites with thermally-stable imidazolium modified clay

Dialkyl imidazolium salt with better thermal stability than the commonly used dimethyldioctadecyl ammonium salt was synthesized and ion exchanged on the montmorillonite surface. Polypropylene nanocomposites with different volume fractions of the obtained organo-montmorillonite (OMMT) were prepared and the effect of the modified clay on the gas barrier and mechanical properties was studied. Wide angle X-ray diffraction (WAXRD) and transmission electron microscopy (TEM) were used to investigate the microstructure obtained. Thermal behavior of the composites analyzed by thermogravimetric analysis was observed to enhance significantly with the filler volume fraction. The gas permeation through the nanocomposite films markedly decreased with augmenting the filler volume fraction. The decrease in the gas permeation was even more significant than through the composites with ammonium treated montmorillonite. Better thermal behavior of the organic modification owing to the delayed onset of degradation hindered the interface degradation along with detrimental side reactions with polymer itself. Transmission electron microscopic studies indicated the presence of mixed morphology i.e., single layers and the tactoids of varying thicknesses in the composites. The crystallization behavior of polypropylene remained unaffected with OMMT addition. A linear increase in the tensile modulus was observed with filler volume fraction owing to partial exfoliation of the clay.     

Adsorption and Micellization in Solutions of Dodecylpyridinium Bromide–Nonionic Surfactant Mixtures

Dependences of the surface tension of aqueous solutions of cationic (dodecylpyridinium bromide) and nonionic (Tween 80, Triton X-100) surfactants and their mixtures on total surfactant concentration and solution composition were studied. The values of critical micellization concentration (CMC) and excess free energy of adsorption were determined from tensiometric measurements. Based on Rubingh–Rosen model (approximation of the theory of regular solutions), the compositions of micelles and adsorption layers at the solution–air interface as well as parameters of interaction between the molecules of cationic and nonionic surfactants were calculated for the systems indicated above. It was established that, in the case of surfactant mixtures with considerable difference in the CMCs, the micelles of individual surfactant with lower CMC value are formed. The effect of negative deviation from the ideality during the adsorption of surfactants from mixed solutions at the solution–air interface was disclosed. It was shown that the interaction energy depends significantly on the composition of mixed systems.     

Polypropylene-Clay Nanocomposites: Comparison of Different Layered Silicates

In former studies of the preparation of polypropylene(PP)-clay nanocomposites, different types of layered silicates were used. However, the obtained results were not comparable due to different preparation conditions and types of silicates. The aim of this work was the investigation of the influence of different layered silicates on the properties of the resulting nanocomposites. FT-IR-spectra, SAXS, TEM micrographs, elemental analysis, mechanical properties and surface tension measurements were used for the comparison of the four different layered silicates under investigation.     

聚丙烯/蒙脱土纳米复合材料Ⅰ.制备、表征及动态力学性能

用原位接枝插层法成功地制备了聚丙烯 /蒙脱土纳米复合材料 (PPMNC) .采用X射线衍射研究复合材料中蒙脱土硅酸盐片层间距 ,发现硅酸盐片层间距从 1 94nm升至 4nm左右 .同时研究了PPMNC的动态力学性能 ,结果表明 :PPMNC的动态储能模量明显高于聚丙烯 (PP) ,尤其在T >Tg 高温段 ,甚至可以达到PP基体的 2倍     

Mutual Influence of Some Flavonoids and Classical Nonionic Surfactants on Their Adsorption and Volumetric Properties at Different Temperatures

Due to the increasing practical use of mixtures of flavonoids with nonionic surfactants the presented studies were based on the measurements of surface tension and conductivity of aqueous solution of the quercetin (Q) and rutin (Ru) in the mixtures with Triton X-114 (TX114) and Tween 80 (T80) as well as the contact angle of model liquids on the PTFE surface covered by the quercetin and rutin layers. Based on the obtained results components and parameters of the quercetin and rutin surface tension were determined and the mutual influence of Q and Ru in the mixtures with TX114 and T80 on their adsorption and volumetric properties were considered. It was found, among others, that based on the surface tension isotherms of the aqueous solution of the single flavonoid and nonionic surfactant, the surface tension isotherms of the aqueous solution of their mixture, the composition of the mixed monolayer at the water-air interface as well as the CMC of flavonoid + nonionic surfactant mixture can be predicted. The standard Gibbs energy, enthalpy and entropy of the adsorption and aggregation of the studied mixtures were also found, showing the mechanism of the adsorption and aggregation processes of the flavonoid + nonionic surfactant mixture.     

Characterization of polypropylene (PP) nanocomposites for industrial applications

This study aims in the examination of a new class of materials named polymer layered silicate nanocomposites. In our case, composites are usually combinations of polypropylene matrix with solid mineral reinforcements named silicates (e,g. montmorillonite, a natural clay). In this study, two complementary techniques used to characterize nanocomposites. Fourier transform infrared spectroscopy (FT-IR) both in transmission and attenuated total reflectance (ATR) modes combined with X-ray photoelectron spectroscopy (XPS).     

Factors and processes influencing the reinforcing effect of layered silicates in polymer nanocomposites

The analysis of the tensile yield stress of a large number polymer/layered silicate composites showed widely differing mechanical properties. The composition dependence of yield stress can be described and evaluated quantitatively by a simple model developed earlier for particulate filled polymers. The comparison of data produced in our laboratory or taken from the literature indicated that several processes may take place during the preparation of the composites and a considerable number of factors influence composite properties. Quite a few of these are often neglected and percentage increase in modulus, strength or other properties is reported in published papers instead. The most important of such effects are changing matrix properties when a functionalized polymer is used to promote adhesion (PE, PP), modification of crystalline structure due to nucleation (PA, PP), plasticization or lubrication (PVC), decreased interaction (PA, PVC, PET, rubbers) or chemical reactions (PVC, PP, PET). Using a few simple assumptions, most of which are supported by previous experience, the extent of exfoliation can be estimated quantitatively in nanocomposites. The analysis of the tensile yield stress of more than 80 composites with various matrices indicated that the extent of exfoliation is very low in most composites; it reaches maximum 10% in the best case, which corresponds to about 10 silicate layers per stack. Although the approach has limitations and several factors were neglected during analysis, this result is in agreement with observations indicating that complete exfoliation rarely can be reached in thermoplastic/clay composites. In order to achieve larger reinforcement, silicates must be exfoliated more perfectly in the future.     

Adsorption/aggregation of surfactants and their mixtures at solid-liquid interfaces

Adsorption of surfactants and polymers at solid-liquid interfaces is used widely to modify interfacial properties in a variety of industrial processes such as flotation, ceramic processing, flocculation/dispersion, personal care product formulation and enhanced oil recovery. The behavior of surfactants and polymers at interfaces is determined by a number of forces, including electrostatic attraction, covalent bonding, hydrogen bonding, hydrophobic bonding, and solvation and desolvation of various species. The extent and type of the forces involved varies depending on the adsorbate and the adsorbent, and also the composition and other characteristics of the solvent and dissolved components in it. The influence of such forces on the adsorption behavior is reviewed here from a thermodynamics point of view. The experimental results from microcalorimetric and spectroscopic studies of adsorbed layers of different surfactant and polymer systems at solid-liquid interfaces are also presented. Calorimetric data from the adsorption of an anionic surfactant, sodium octylbenzenesulfonate, and a non-ionic surfactant, dodecyloxyheptaethoxyethylalcohol, and their mixtures on alumina, yielded important thermodynamic information. It was found that the adsorption of anionic surfactants alone on alumina was initially highly exothermic due to the electrostatic interaction with the substrate. Further adsorption leading to a solloid (hemimicelle) formation is proposed to be mainly an entropy-driven process. The entropy effect was found to be more pronounced for the adsorption of anionic-non-ionic surfactant mixtures than for the anionic surfactant alone. Fluorescence studies using a pyrene probe on an adsorbed surfactant and polymer layers, along with electron spin resonance (ESR) spectroscopy, reveal the role of surface aggregation and the conformation of the adsorbed molecules in controlling the dispersion and wettability of the system.     

The standard free energy of surfactant adsorption at air/water and oil/water interfaces: Theoretical vs. empirical approaches

The standard free energy of surfactant adsorption represents the work of transfer of a surfactant molecule from the bulk of solution to an infinitely diluted adsorption layer. This quantity can be determined by non-linear fits of surface-tension isotherms with the help of a theoretical model of adsorption. Here, the models of Frumkin, van der Waals and Helfand-Frisch-Lebowitz are applied, and the results are compared. Irrespective of the differences between these models, they give close values for the standard free energy. The results from the theoretical approach are compared with those from the most popular empirical approach. The latter gives values of the standard free energy, which are considerably different from the respective true values, with c.a. 10 kJ/mol for nonionic surfactants, and with c.a. 20 kJ/mol for ionic surfactants. These differences are due to contributions from interactions between the molecules in dense adsorption layers. It is concluded that the true values of the standard free energy can be determined with the help of an appropriate theoretical model. For the processed sets of data, the van der Waals model gives the best results, especially for the determination of the standard adsorption enthalpy and entropy from the temperature dependence of surface tension. The results can be useful for the development of a unified approach to the thermodynamic characterization of surfactants.     

Transient Surface Tension of an Expanding Liquid Sheet

We address the problem of dynamic surface tension using measurements of sheet diameters that results from the impact of a liquid jet of diameter d(0) on a small disk of diameter d(i) (d(i)/d(0) approximately 4). At low velocities, the sheet diameter D is related to d(0) by the Weber number We, constructed with the liquid density rho, the jet velocity u(0), and the surface tension sigma at the rim: D/d(0)=18 We=18 [rho u(0)(2)/(sigma/d(0))]. This relation expresses the equilibrium between inertial forces and surface tension forces at the sheet rim. When a surfactant has been dissolved in the bulk of the liquid prior to the formation of the initial jet, the rim surface tension, and therefore the sheet diameter, depends on the amount of surfactant adsorbed at the rim. This amount is fixed by a competition between surface formation induced by radial extension and repopulation of the liquid interface in surfactant. The experimental setup proposed here provides a method to measure dynamic surface tension from sheet diameter measurements and symmetrically to monitor the adsorption of a surfactant on a liquid surface. The available adsorption time ranges from 10 to 100 ms. Experimental data obtained with two surfactants are in agreement with a model of a diffusion-controlled adsorption at the interface. Copyright 2000 Academic Press.     

Monitoring surfactant-induced hemolysis by surface tension measurement

Surface tension measurements were employed to monitor the erythrocyte hemolysis process induced by surfactants. Two types of surfactants were used: the cationic surfactant DTAB and the anionic surfactant SDS. During DTAB-induced hemolysis, the changes in surface tension clearly demonstrate three stages. The first stage is characterized by surface tension increase, which is explained by surfactant removal from the suspending solution, due to adsorption onto cell membranes. In the second stage, surface tension remains constant, implying that equilibrium is attained between the membrane-bound surfactant and the surfactant in solution. The third stage is characterized by surface tension decrease that begins simultaneously with measurable cell-interior release, and lasts until hemolysis is completed. With SDS-induced hemolysis, the same three stages are observed at a low concentration; however, fluctuational increase in surface tension is obtained for higher concentrations. The latter is explained by additional adsorption of surfactant to solubilized membrane fragments.     

Polymer/surfactant interactions at the air/water interface

The development of neutron reflectometry has transformed the study and understanding of polymer/surfactant mixtures at the air/water interface. A critical assessment of the results from this technique is made by comparing them with the information available from other techniques used to investigate adsorption at this interface. In the last few years, detailed information about the structure and composition of adsorbed layers has been obtained for a wide range of polymer/surfactant mixtures, including neutral polymers and synthetic and naturally occurring polyelectrolytes, with single surfactants or mixtures of surfactants. The use of neutron reflectometry together with surface tensiometry, has allowed the surface behaviour of these mixtures to be related directly to the bulk phase behaviour. We review the broad range of systems that have been studied, from neutral polymers with ionic surfactants to oppositely charged polyelectrolyte/ionic surfactant mixtures. A particular emphasis is placed upon the rich pattern of adsorption behaviour that is seen in oppositely charged polyelectrolyte/surfactant mixtures, much of which had not been reported previously. The strong surface interactions resulting from the electrostatic attractions in these systems have a very pronounced effect on both the surface tension behaviour and on adsorbed layers consisting of polymer/surfactant complexes, often giving rise to significant surface ordering.